Search Documents

By James L. Christensen, Gregory Sanchez, Michael P. Walker

The Fogg Museum expansion project required excavation and construction in a congested urban area in Cambridge, Massachusetts. A soldier pile tremie concrete (SPTC) wall provided the support of excavation and now serves as the permanent basement wall of the new expansion of the museum. The existing Fogg museum had a single basement level. The new expansion has a two-level basement for new exhibit space and an amphitheater. The east side of the site is about 20 feet above the basement level of the existing Fogg structure which resulted in a significant unbalanced load that needed to be resolved without damaging the original Fogg structure. The SPTC wall was supported with a combination of tiebacks and internal bracing. The final depth of the excavation was about 40 feet below street level. Strict movement control was imposed because the existing museum contained an Italian Renaissance-style courtyard. The southeast corner of the SPTC wall had to accommodate underpinning of an historic concrete ramp which was ultimately incorporated into the expansion. Challenges during construction included excavating the SPTC wall panels up to 12 feet into argillite bedrock which had occasional diabase dikes and sills. The following topics are discussed in more detail after a general project.

Jan 1, 2015

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By Dan Mahrt

"In June of 2009, a slope failure occurred along River Road in Bismarck, North Dakota. The slope failure affected approximately 300 feet of River Road with vertical displacements up to 3 feet, resulting in closure of the road. River Road travels along the Missouri River in Bismarck in a geologic area riddled with historic slope failures of varying sizes. River Road is a city roadway which travels along the Missouri River. The toe of the failure extended into the Missouri River, therefore methods to repair the slope needed to be constructed within United States Army Corps of Engineers (USACE) requirements, and be acceptable to the City of Bismarck. As this is a scenic area along the river, the stakeholders desired to maintain the scenic landscape along the roadway as a part of the slope stabilization.Due to the magnitude movement of the failure mass, the geometry of the failure was relatively easy to evaluate. In evaluating remediation options and collaborating with the USACE, the team determined that the scarp was situated primarily within the navigable portion of the Missouri River. This required USACE approval for any repair or remedial work downslope of the roadway. The City of Bismarck wished to reopen the roadway as soon as possible, therefore stabilization options were limited to working within the road right-of-way to avoid permitting for working within the navigable waterway.The remediation solution for this project involved a combination of driven H-pile and placement of lightweight fill to re-construct the roadway at the original grades, and avoid impacting the navigable portions of the Missouri River. This paper discusses the unique project constraints and the innovative solution using multiple technologies to successfully stabilize the slope.BackgroundIn June 2009, Bismarck, North Dakota experienced two consecutive days of significant rain resulting in over 5 inches of precipitation in a 36-hour period. Shortly after these rain events, a slope failure was noted on River Road, a city street along the Missouri River in Bismarck. Initial findings noted the slope failure affected about a 300-foot long portion of the roadway, with vertical displacements of about 2 feet. The city of Bismarck closed the roadway and began evaluating repair solutions for the road."

Jan 1, 2016

By Christian Hoyme, Jochen Maurer

Most of the current foundation projects are suffering from disconnected information silos. In the first silo there is the planning of the project with corresponding data, presented by paper or digital drawings. Here will Building Information Modeling (BIM) be one of the trends for the future. We will see more and more projects leaving the “old way” of 2D drawings and moving into 3D planning including metadata of the foundations. But even with a perfect BIM model of a jobsite, we are not at final end of digitalization. While execution of the project at the jobsite, a second data silo is evolving. Data collected directly from construction equipment and manual measurements is currently undervalued in most projects. Paper is passed to the equipment operator and major data from measurements on site are noted on paper and digitized afterwards. Automatically collected data is not be used to create site progress reports or similar report. So, the real “data” just flows around without connection to any other data already existing in projects. And then the third silo arises: The documentation of the project. Data collected on paper es reentered to create some basic documentation of the work handed over to the client. Spreadsheet software is still the “tool-to-be-used” to create at least some documentation. Finally, the documentation is not connected to the data created while planning and not connected to the automatically collected data from the jobsite. A connected jobsite in the foundation industry must link these information silos and have to create a full data-workflow from the design through the execution to the as-built documentation. INTRODUCTION Building information modelling (BIM) is currently the most popular term of construction business in Germany and probably all over the world. But as often there are many different definitions out there and everyone has his own definition or at least understanding what BIM is about. But for sure it is the most relevant for the construction industry in the near future. Most popular is the digital twin for the upper structure of a building. In most cases the BIM models just shows the building itself, but there is more to be implemented. For example: projects where a special foundation is needed, BIM should include also the foundation elements with meta data. There are several advantages. Not only the clash detection of anchors, but also the possibilities to check the interaction with neighbor constructions, power lines and so on are a use case. For sure most of the special foundation elements are not relevant for the whole lifecycle of a building. But during construction and later the demolition the information about the hidden elements is important and gives a benefit to all stakeholders. In the future there will be not the question: “What is already in the ground?”. The risk for following construction projects on the same ground will be minimized.

Jan 1, 2019

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique?s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay, and silt formations.

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique’s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay,

Jan 1, 2017

By Bo Westerberg, Mattias Andersson, Yvonne Rogbeck

"Deep stabilisation has been used in Sweden for decades. The method has been improved to allow it to be used in different types of soils and with new binders. One challenging soil type in Sweden is so-called sulphide soil, a fine-grained soil which contains organic material and iron sulphides. There have been some cases in Sweden of problems when using deep stabilisation in this type of soil, and in one case a slope failure occurred. This paper shows that it is possible to achieve good results with deep stabilisation in sulphide soils. Laboratory and field studies from a test site along the Botniabanan railway line in Sweden are presented. Geotechnical and chemical properties of the natural soil were investigated in the laboratory and one or more of these properties may explain the differences in the stabilising effect of sulphide soils. The strength of the laboratory samples and the columns in the field were tested and compared. It is shown that a satisfactory stabilisation effect can be achieved with the proper choice of binder, amount of binder added, curing time and mixing energy. In sulphide soils, more binder additive is needed than in “ordinary” inorganic clays.1. INTRODUCTIONThe term sulphide soils is used in this paper to refer to the unique types of sulphide soil commonly found in the coastal areas along the north-eastern coastline of Sweden between the cities of Gävle and Haparanda, a distance of about 900 km. Sulphide soils are in general very compressible, susceptible to creep deformation and normally show low undrained shear strength. A sulphide soil may have a negative environmental impact through acidification and chemical action if it is subjected to oxygen, for example during excavation or lowering of the ground water table, Mácsik (1999). In foundation engineering works, efforts are made, for environmental or/and economic reasons, to use the sulphide soil as the foundation instead of excavating it. Deep stabilisation by means of columns is a potential method for use when sulphide soil needs to be improved in order to reduce settlements or/and increase the stability of embankments.Sulphide soils were formed as sediments at river mouths and off the coast in the special environment prevailing at the time of sedimentation, Mácsik (1994). The water in which the sulphide soil was sedimented was brackish/sweet and the environment was typically deficient in oxygen. The environment prevented complete decomposition of the organic material in the sediments. As a result, sulphide soils were formed primarily in the form of a fine-grained composition of clay and silt minerals, iron sulphides and organic matter. Such environments still exist today and new sulphide soil sediments continue to be formed."

Jan 1, 2015

Technically speaking, the concept of NDT sounds like the "magic bullet" when faced with a questionable drilled shaft. All the Contractor or Engineer needs to do is select an NDT method, apply it, understand the details and extent of the defect and determine whether it will impact the load carrying capacity of the shaft during it’s design life. Unfortunately, it is not that simple. NDT is a tool utilized to indirectly assess the condition of the completed drilled shaft. For the most effective interpretation, NDT data should be correlated with the subsurface information, visual observation, and detailed shaft installation records. The basis for acceptance or rejection of drilled shafts should not be solely based on NDT. The parties responsible for specifying, interpreting and using the NDT results must understand the capabilities and limitations of the method to be utilized, in conjunction with the relevant subsurface conditions of the site, before selecting and specifying a system and acting on the results. This is necessary so that an appropriate NDT method can be specified and contracted. In this manner the results and roles of the responsible parties can be clearly defined.

Jan 1, 2004

By Pierre Gouvin, Michael Oakland

"This paper covers the rapid response methods used to monitor the emergency response to damage to an historic structure. An architectural gem, the latest incarnation of the old south Church was completed in 1875, utilizing local conglomerate (pudding stone), combined with brownstone and other materials to make an incredible showcase for priceless stained glass and other details epitomizing the height of the American Industrial Revolution. As part of required American with Disabilities retrofits to the adjacent Metropolitan Boston Transit Authority Station (MBTA), a support of excavation system was implemented with tradition sheet piles. During excavation (SOE) it was determined that Jet Grouting would need to supplement the sheeting to close openings in the SOE. During Jet Grouting, the eastern side of the structure was bisected, and lifted over 2 inches up and to the south. The movement occurred rapidly, within minutes, and subsided when Jet grouting was discontinued. The paper will describe the nature of the immediate response to get a real time monitoring program established, and the follow on monitoring program that ensued to provide the needed information to the stakeholders about this critical structure to evaluate stability, safety and to develop a long term remediation plan. The real time systems and instruments used consisted of Automated Motorized Total Stations (AMTS) and Automated Crackmeters. The Paper will describe the techniques used to control construction in safe manner.INTRODUCTIONThe Old South Church of Boston was constructed in 1875 and is one of the best examples of High Victorian Gothic Architecture in the Northeast. (Fig. 1) shows the newly constructed Old South in 1882. The Roxbury Conglomerate used to construct the church combined with large stained glass window by Clayton and Bell of London provides its unique appearance. Like most of the structures constructed in Boston’s Back Bay at that time, the church is founded on timber piles which penetrate the fill and organic soils to bear in the upper Boston Blue Clay. The churches interior includes high vaulted plaster ceilings and a 1920’s E. M. Skinner organ with exposed pipes as long as 32 ft. in length. The Church was added to the list of National Historic Landmarks in 1970 and is a featured Boston attraction."

Jan 1, 2017

By Nils Schneider, Marc Peters, Stefan Frey, Andrea Fluck

Due to the worldwide population growth, the development of sustainable infrastructure and the exploration of renewable energies plays a key role to handle the rising megacity trends and to limit carbon footprint. Herrenknecht AG is a leading manufacturer of Tunnel Boring machines and has constantly endeavored through its extensive Research and Development programs to address limitations faced by the civil engineering industry as regards to construction equipment capabilities. New mechanized technologies, mainly coming from the tunnelling industry, have been developed by Herrenknecht AG as an efficient alternative to conventional civil engineering, where tailor-made concepts are required to comply with restricted conditions onsite. Very often this innovation led technology capability has meant making construction processes safer due to minimal human intervention and also far more productive due to higher performance as compared to other latest or conventional methods of construction. The rising need for even higher building structures and large-capacity bridges involve the development of innovative deep foundation technologies for on- and offshore operation. Conventional methods like bore piles reach their technical and economic limits under certain conditions. For building shafts and foundations, the mechanized Vertical Shaft Sinking Machine technology (VSM) from Herrenknecht AG is a proven innovation and has now been used in various onshore infrastructure projects worldwide to construct a total of 94 circular shafts in depths of up to 115 meters. It operates below the groundwater level, completely remote-controlled from the surface in a diameter range from 4.5 to 18 meters. Subsequently Herrenknecht noted that Offshore foundations, especially in non-drivable ground conditions such as soft and hard rock (e.g. limestone, sandstone, mudstone, granite etc. or soft soil with high density) and shallow continental shelf (water depth approx. 20-60m), presented construction challenges and equally an opportunity for building high performance equipment. The latter construction conditions usually requires drilled installation methods for applications such as harbor enlargements, bridge foundations and foundations for offshore wind turbines. The Offshore Foundation Drilling technology (OFD®) is Herrenknecht’s latest innovation, incorporating our learnings from the VSM and full-face Tunnel Boring machines, and the OFD® enables a rapid and economical offshore installation in such variable ground and rock conditions. This paper will discuss the technology behind the new mechanized technology of VSM and Herrenknecht’s latest innovation of the OFD® along with their respective application fields in foundations construction. The paper will further present in details, their range of benefits to the construction industry.

Nov 1, 2022

By K. Rainer Massarsch

"Part 1 of 2 By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenINTRODUCTIONConstruction activities, such as driving of piles and sheet piles, soil compaction or excavation generate noise and vibrations. In populated areas these can have a negative impact on the environment, disturb inhabitants and, under unfavorable conditions, cause damage to buildings and installations. This condition is aggravated by the growing public awareness of environmental issues and the increasing use of vibration-sensitive electronic equipment and machinery in industry. In many countries, environmental regulations are enforced more stringently and limit or even prohibit the use of impact or vibratory hammers. This development has restricted the use of cost-effective foundation methods, such as driven and vibrated piles and sheet piles.Vibration problems are gaining importance in many European countries and extensive research has been performed during the past decade, especially with respect to traffic vibrations (Massarsch, 2004). Significant progress has been made owing to the availability of high-quality field measurements and an improved theoretical understanding of how vibrations are generated and transmitted through soil layers. These findings can also be applied to vibration problems associated with construction activities. However, this information is not yet appreciated by the geotechnical profession and even less by the construction industry.This paper discusses the effects of ground vibrations on the surrounding soil and on buildings, with particular emphasis on the different mechanisms of damage that may occur. Guidance is given on the elements which should be taken into account in an assessment of risks associated with piling projects. A simplified method is proposed for assessing the risk of settlements or strength loss in soil deposits. Limiting vibration levels are presented, based on the Swedish standard, which can be used to assess the risk of damage to buildings. Aconcept to predict ground vibrations caused by pile driving and the mechanisms which control the propagation of ground vibrations, will be presented in the second part of this paper."

Jan 1, 2004

By Peter Cali, Wesley Schmutzler

"The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.IntroductionDuring hurricane Katrina the levee that constitutes LPV-111 was overtopped and breached in several locations. The United States Army Corps of Engineers (USACE) was presented with the task of increasing the level of the flood protection around New Orleans after Hurricane Katrina to the 100- Year hydraulic grade - the level of protection that provides risk reduction from a storm surge that has a 1% chance of being equaled or exceeded in any given year - and the firm project completion deadline was June 2011.LPV-111 is located in East New Orleans and a large portion of the levee is adjacent to the Bayou Sauvage National Wildlife Refuge. The levee could not encroach on this area. This provided a limited footprint for the levee and made construction of conventional levee difficult, if not impossible. The total length of the project was 5.3 miles. Included in the project was the rehabilitation of one main pumping station and one smaller pump station for water management within the refuge. Short sections of “T” wall were used at the tie in at the Lake Borgne Surge Barrier, the main pump station and the CSX Railroad crossing"

Jan 1, 2017

By Kaustuv Bhattacharya, Manish Kumar, Nirbhay Singh, Prodyot Kr. Ray, Praveen Soin

This paper highlights salient features of an excavation 38 m (Length) by 10 m (Width) by 24 m (Depth) carried out in Central Kolkata. Secant pile wall (SPW) formed using a combination of alternating 1200 mm & 800 mm diameter piles was used. Six layers of struts and waler beams, including bottom slab were utilized as lateral restraints to piles. The geotechnical profile for excavation zone was predominantly silty sand to sandy silt. The profile is characteristic of river channel deposit usually encountered in Kolkata. Temporary stage analysis (including seepage analysis) and design were carried out in FEM softwares. Design checks for clay bursting, piping, bottom heave, etc. were also carried out. Extensive instrumentation and monitoring were carried out during the excavation period to check parameters such as ground movement, pile movement, piezometric heads, etc. as per review levels. During excavation, ground improvement using Tube-a-manchette grouting technique was also required to be carried out as per field observations. The paper discusses some of the major challenges faced as well as measures taken to counter them, during deep excavation carried out in silty soils in a very congested Urban setting in the heart of a Megacity.

Sep 1, 2022

By Vijaya Bhushan Rao, Ali Semercioglu, Jason Redgers

Large diameter steel water tanks with high storage capacities impart heavy loads deep into the ground, generally requiring deep foundations to adequately support them. The use of ground improvement as a sustainable and cost effective alternative is tempting but the design of the foundations for such heavily loaded, thin-shelled structures have to meet several performance requirements such as bearing capacity, limiting the specified total settlements, typically limiting the radial differential settlement to 13mm over 10m along the circumference and dishing settlement from edge to center of 1/120 as per standard API 650 Appendix B as well as the mitigation of liquefaction induced settlement risk. Any inadequacy in the soil investigation, geotechnical design, or misrepresentation of stresses of the foundations may lead to serviceability compromise or potentially catastrophic failures. Therefore, the selection of the foundation is dependent on the availability of suitable ground report and the limitations imposed by operational requirements. Two such case studies are evaluated and compared in this paper, with tank diameters ranging from 41 to 106m in the Kingdom of Saudi Arabia, (KSA) which were founded on two types of soils and supported on deep foundations i.e., stone columns and bored cast-in-situ piles.

Oct 1, 2022

By A. B. Cerato, M. K. ElSawy, A. Elgamal

"Helical piles are gaining popularity as foundations for new construction as well as retrofitting option for deficient foundations. More recently, large diameter helical piles are used to support structures in regions characterized with high seismic hazard. Even though they have proven to be viable in seismic areas such as New Zealand, where they experienced little damage during the Christchurch earthquake, the knowledge about their seismic analysis and performance is largely lacking. Therefore, there is a need for comprehensive study to evaluate their performance under seismic loading. The current objective of this study is to investigate the performance of helical piles through a full-scale testing program that was performed at the NEES/UCSD Large High Performance Outdoor Shake Table (LLHPOST). The experimental setup involved ten steel piles of different configurations installed in dry sand. The piles were loaded with different masses and were subjected to different earthquake signals to simulate different dynamic behavior. This paper compares the performance of different moment curve fitting methods used to interpret the test data. Furthermore, the effects of different frequency content of loading on the pile response is illustrated in terms of deflection along the shafts of tested piles with different configurations.INTRODUCTIONEarthquakes are a major hazard for structures situated in seismic regions, and dynamic loading must be a design consideration. Successful design of a foundation system entails providing a safe and economic foundation solution to resist earthquake loading. Different foundation options have been used to support buildings in high seismic regions. Helical piles represent a viable foundation option that offers several advantages in terms of ease of installation, lower cost and environmental impact, ability to approximate the axial capacity directly from torque readings and more (Perko 2009). However, they are not typically considered as an option in many seismic regions. Meanwhile, several buildings supported on helical piles in New Zealand have survived the Christchurch earthquake with negligible damage, which encourages performing further research to understand the behaviour of these piles under seismic loading.A helical pile consists of a steel shaft fitted with a steel helix/helices. The helical pile is installed by applying torque to its head via mechanical torque. Nowadays, helical piles are used in a wide range of applications such as foundations for light posts and residential houses. The static behaviour of helical piles has been studied extensively and is relatively well understood (Tsuha and Aoki 2010; Mittal et al. 2010; Sakr 2011; Elsherbiny and El Naggar 2013; El Sharnouby and El Naggar 2012; Elkasabgy and El Naggar 2015; Weidong et al. 2015 and Bagheri and Naggar 2015) However, the dynamic and seismic behaviours of helical piles is seldom investigated (Elkasabgy and El Naggar 2013). This underscores the knowledge gap currently present regarding the seismic behaviour of helical piles."

Jan 1, 2017

It is my great pleasure as mayor of the city of Amsterdam to welcome you today to Amsterdam, and to the 10th International Conference on Piling and Deep Foundations. The history of Amsterdam has been connected intimately with your professions of geo-engineering and geotechnology, since its very first days. It is good to be aware that you are part of a very old tradition. The knowledge that we need today to build and renew the city has been gathered over a century long process so that we fortunately can stand on the shoulders of the giants before us. During the centuries people living in this part of the Netherlands have always struggled against the water. The same waters that brought the opportunity for a seafaring country to discover the world and to build an empire in the 17th century were a threat to the low lying Netherlands.

Jan 1, 2006

By Sudip Basack

"The topic of pile foundation subjected to lateral cyclic load is an age-old problem confronted by Geotechnical Engineers. The environment prevalent in ocean and shorelines necessitates the piles supporting offshore and onshore structures to be designed accounting for the lateral cyclic loading resulting from the effects of sea waves. The quasi-static nature of this type of loading induces remarkable deterioration in the interactive performance of the soil-pile system. This can be manifested as progressive loss in pile capacity associated with increased pile head deflection. The work reported herein is aimed towards conducting rigorous theoretical analysis using finite difference technique so as to analyze the lateral cyclic loading response of a single, vertical pile embedded in cohesionless soil. The theoretical results are compared with the experimental results and reasonably good agreement is noted. This paper presents a brief description of the theoretical analysis carried out with some typical results and the relevant conclusions drawn therefrom. 1. INTRODUCTIONOffshore structures, namely, quay & harbour structures, jetties, tension leg platforms, oil drilling platforms, etc. are largely supported on pile foundations. Apart from usual loads from superstructures, these piles are subjected to continuous action of wave loading. This type of lateral loading is quasi-static cyclic in nature which results in considerable degradation in the interactive performance of the pile-soil system initiating progressive reduction in pile capacity associated with increased pile-soil stiffness. This may ultimately lead to disastrous consequences.Amongst limited research works in this field, the major contributions are made by Matlock (1970), Idriss et al (1978), Poulos (1982), Vucetic et al (1988), Long & Venneste (1994) and Basack (1999). A brief review of these works indicates that the degradation of the pile-soil system under lateral cyclic loading mainly depends upon the following parameters: number of cycles, frequency (cycles per unit time), cyclic load level (ratio of cyclic load amplitude to the lateral static ultimate pile capacity, in case of loadcontrolled mode) and cyclic displacement level (ratio of cyclic displacement amplitude applied at the pile head to the external pile diameter, in case of displacement-controlled mode). As pointed out by Poulos (1981 & 1982), the degradation is mainly due to: 1) partial to zero dissipation of excess pore water pressure generated during cyclic loading in progress, 2) destruction of interparticle bond with particle realignment and 3) rearrangement and gradual accumulation of permanent plastic deformation around pile"

Jan 1, 2005

By John P. Turner, Benjamin J. Turner

"Tieback anchors are now used routinely for landslide stabilization in the USA and abroad. It is generally understood by design engineers that friction loss over the unbonded length of a tieback anchor is inherent to the system, and such loss is permitted as long as it does not exceed a certain threshold, typically 20 percent of the post-tensioning load. However, recent experience from projects utilizing tieback anchors with unbonded lengths in excess of 150 feet has demonstrated that this criterion may be difficult to achieve, particularly in certain ground conditions. Furthermore, anchor friction loss, even if below the 20-percent threshold, has important implications for the stability of the slope that are often ignored in practice. This paper presents the results of a study in which friction loss is quantified from load test data for projects in a variety of ground conditions by means of a “wobble coefficient.” Factors that may influence the wobble coefficient are examined, and recommendations for addressing this issue in practice are presented. A recent instrumented load-test program for a landslide stabilization project in Southern California is examined, demonstrating that with appropriate monitoring controls, uncertainty with regard to friction loss can be minimized. IntroductionSteel-strand tieback anchors have been used by the geotechnical community to support shoring systems for many decades, and more recently as a means to stabilize landslides. For strand encased in grease-filled plastic sheathing, which is intended to allow the strand to elongate freely, some load can still be transferred by friction between the strand and the grease and between the grease and sheathing. The sheathing then transfers load to the surrounding grout and, in the case of ground anchors, to the surrounding soil or rock. The resulting decrease in load over the length of the unbonded zone is known as “friction loss.”A widely used criterion for ground anchor acceptance based on load testing is that the measured anchor elongation must achieve a minimum value of 80 percent of the theoretical elastic elongation, or in other words the actual elongation can be up to 20 percent less than the theoretical value. This ensures that the majority of the load applied at the anchor head is reaching the bond zone behind the assumed failure surface, since load shed within the failure mass does not contribute to stability. This criterion acknowledges that friction loss is an inherent feature of the anchor system which cannot be eliminated completely, only minimized."

Jan 1, 2017

By Esam Abraham

A 13.6 mile portion of the 500 kV Tehachapi Renewable Transmission Project crosses the mountains of the Angeles National Forest. Access and environmental constraints precluded road development for most transmission tower foundations, tower erection and conductor stringing operations. Because of the access constraints, helicopter-supported micropile foundation construction was used for this steep and environmentally sensitive portion of the project. The general methodologies incorporated on the project represent innovative implementations of micropile design criteria, preconstruction micropile installation and verification testing, on-site geotechnical characterization, micropile and pile cap installation, and proof load testing. Challenges in constructing the 224 foundations for 56 transmission towers provide lessons learned related to transmission lattice steel tower specific design constraints, construction challenges (environmental and geotechnical), and construction schedule.

Jan 1, 2010

By Paul Doherty

It is known that the axial capacity of a displacement piles installed in clay varies with time. Consolidation theory suggests that dissipation of porewater pressure set-up during pile installation would lead to increased effective stress and hence higher pile resistance. In recent years a number of case histories have reported time dependent capacity increases for piles installed in sand. Although there is some debate regarding the physical mechanisms controlling this phenomenon, known as ageing, it is unrelated to pore pressure dissipation as piles in sand are installed in primarily drained conditions. A series of field tests designed to investigate ageing effects in soft clay are presented in this paper. Full-scale load tests on 6m long 250 mm square concrete piles, which were driven into soft clay are described. The piles were first tested approximately 100 days after installation, at which stage full equalization of the excess pore pressures had occurred. Static load tests were then performed up to 10 years after pile installation. The piles exhibited significant ageing, with their shaft resistance increasing by up to 66% over a 10 year period. Possible mechanisms for such aging characteristics are explored.

Jan 1, 2011