Search Documents

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998

By S. Schwartz, T. Bilney

"Over recent years a number of techniques have been developed as part of the AMIRA1 P9 project to represent mathematically or measure directly sub-processes occurring in flotation cells. These include the determination of:•,?a machine parameter (bubble surface area flux, Sb);•,?a froth parameter (froth recovery, Rf );•,?entrainment and drainage parameters (???and d); and•,?an ore floatability parameter (Pi).These flotation parameters allow the plant engineer to develop a model of the flotation circuit that can be used as a powerful tool to diagnose the performance of that circuit. The recently developed JKSimFloat V6 flotation simulator uses these parameters to predict the flotation circuit performance that would arise from changes in operating conditions and circuit configuration.This new flotation technology was applied to the Placer Kanowna Belle Gold Mine in Western Australia. A series of plant surveys, cell characterisation measurements and laboratory batch tests were conducted to determine the flotation circuit model parameters to be used within the JKSimFloat V6 simulatorA thorough flotation circuit analysis was then performed at Kanowna Belle using JKSimFloat V6. The recommendations that were provided by this circuit analysis have resulted in large improvements in the flotation performance at Kanowna Belle. These include a 1.3% increase in flotation gold recovery and a substantial decrease in operating costs. The analysis is still ongoing, however, the benefits already obtained from applying this technology have resulted in a US$1.3 million a year improvement to the mine."

Jan 1, 2005

By Andy Cole

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual-alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

May 1, 2002

By Camilo I. Morales

At present, many open pit mines are designed to operate and feed a processing plant with ore characteristics that were defined in the design of the mining business, which are not necessarily the same as those found during the operation. This is the case of Spence Mine, whose design was conceived considering the extraction of primary iron sulphides, however, with the extraction of such minerals, it was necessary to mine and process minerals with secondary enrichment. Then it is necessary to work with a greater selectivity degree in the operation, however the capacities of the mine and operational resources were not designed for this. Thus, the changes in the general conditions of the operation should be considered as a series of geometallurgical restrictions to achieve production schedules. The above facts impacts directly in the short-term planning, whose task is to achieve the goals proposed in productive long-term planning because the company does not have the tools necessary to plan with the degree of selectivity required, so it should be done by hand, discretizating and scheduling the production polygons. Naturally, this manual process in the short term planning deviate sharply from the areas in operation, opening new fronts and benches that result in a significant increase in costs and a loss of the value of the mineral resource to miss the exploitation sequence. The research presented in this paper is related to the development of a mathematical programming model to support the short-term planning, so as to integrate the challenge of selective mining with geometallurgy restrictions, to provide the planner a guide to construction of the polygon of exploitation, guiding the fines production to achieve the goals of the proposed production plan.

Oct 1, 2009

By S. Dicarlo

"In late 1985, B-zone ore was first processed through the Eldor Mines mill at Rabbit Lake. Extensive modifications had been completed in order to mill this ore. In-plant process development was initiated to tune up the new circuits and concentrated on leaching, solvent extraction, impurity and uranium precipitation and tailing and effluent treatment. This process development effort and the results are described.INTRODUCTIONEldor Mines, a division of Eldorado Resources Limited, operates the Rabbit lake mine-mill complex at Collins Bay on the western shore of Wollaston Lake in northeastern Saskatchewan.The first orebody was discovered in 1968 by Gulf Minerals Canada Limited below a small body of water named Rabbit Lake. Ore from the Rabbit Lake (RL) deposit was first processed through the new mill in June, 1975, with depletion scheduled over the next ten years. Continued exploration in the area led to the discovery of four orebodies in the vicinity of Collins Bay: A-zone (1971), B-zone (1977), D-zone (1978) and Eagle Point (1980). Collins Bay is about ten kilometres from the mill facility.In 1982, Gulf Minerals was acquired by Eldorado Nuclear Ltd., who continued the development effort to bring the B-zone deposit into production. The RL pit was mined out in May, 1984 with stockpiled ore providing mill feed until startup on B-zone ore, which was scheduled for November, 1985."

Jan 1, 1988

By T. Yalcin

"This paper describes the development of a mathematical model for determining the liberation of an ore at various grinding sizes, based on the combined results of microscopic counting, grinding tests, and chemical analysis.The method is illustrated with an application to the magnetite ore of Sherman Mine in Temagomi, Ontario. For this ore, a degree of liberation of 98.7% was determined at a grinding size of 90% passing 44 microns, which closely corresponds to the final grinding size employed at the Sherman Mine Concentrator.Introduction Liberation characteristic of ores have direct and significant bearing on overall economics of concentration processes.Target grades and recoveries can be achieved only it minerals are adequately liberated prior to separation. Degree of liberation depends on the extent of size reduction. However, due to the high costs associated with size reduction processes, it is important to keep size reductions within limits of satisfactory liberation. Prevention of excessive size reduction is also necessary because of inefficient mineral separations in very fine sizes. Hence, a study of reduction size — liberation relationship is essential for optimum profit from milling operations.A number of procedures have been developed for liberation studies (1-12), but there is lack of method for universal adoption.A new approach is presented in this paper that might provide a realistic estimate of liberation and give a practical guidance as to the degree of size reduction required for satisfactory liberation."

Jan 1, 1985

By D. M. Wyslouzil

"Micron or sub-micron size gold inclusions in sulphide minerals cannot be extracted by conventional cyanidation. The gold surfaces must first be exposed by decomposition of the sulphides. As an alternative to roasting, pressure oxidation was found to be a most satisfactory method to decompose the sulphides and expose the gold particles. For cyanidation the pressure oxidation pulp has to be neutralized and stabilized with lime. It was found that thiourea can extract the gold directly from the pressure oxidation pulp without pH adjustment and oxidant addition. The main obstacles against the common use of thiourea are circumvented by a recently described control method of the emf during leaching.INTRODUCTION Amalgamation and cyanidation are the most conventional processes for gold extraction. The prerequisite for gold extraction is the possibility of gold surface to be contacted by mercury or by the cyanide solution. Encapsulated gold has little chance of contact and this leads to poor extractions.The reasons why a gold ore may be refractory are: micron or sub-micron size gold particles included in the sulphide minerals, such as pyrite and arsenopyrite; presence of and association with antimony, arsenic, tellurium and carbonaceous minerals. Some alternative processes, such as double oxidation(1,2), pretreatment with lime , H202, chlorine and Caro's acid, roasting and thiourea leach, have solved some of the problems of ""refractory"", but the sub-micron gold in sulphide minerals still shows little response. Roasting and the cyanidation of the calcine was one of the most successful approaches for this type of gold ore.There are two disadvantages to the roasting process: (1) the generation of sulphur, arsenic, antimony and mercury containing gases is undesirable and the control is extremely expensive; (2) gold particles might be fused in the roasted product and the oxidized base metals in the calcine might reduce the cyanidation efficiency. In recent years the pressure oxidation process has been considered as one of the more effective and satisfactory methods to decompose the sulphide minerals and expose the gold surface to the cyanide leach solution. The pollution problem could be better controlled and the gold extraction is more amenable."

Jan 1, 1985

By B. St. Pierre

"The alchemists' symbol for antimony is a diamond with a dot in the centre. The latin name ''stibium'' gives this mineral its chemical symbol ""Sb"" and the name to the principal ore containing antimony. This is Stibnite, a sulphide of antimony, and the valuable mineral at the Consolidated Durham operations. Stibnite chemically pure contains 71.69% antimony metal.Antimony is used in many forms, as an alloy in the production of metal products and as chemical compounds of oxides and sulphides. In Biblical times, antimony was used as a medicine and as eyebrow makeup.Today, the largest single use of the metal is as a hardener and strengthener of lead, and corrosion inhibitor in storage batteries. New applications for antimony in its oxide form as fire retardants are broadening the overall demand especially in the chemical, plastic and fabric industries. Other users include the Military for such things as tracer bullets, shrapnel, smoke screens and flame throwers. An unusual property of the metal is that it contracts when heated which has made it a valuable alloying metal in the printing industry, for heat shields on re-entry vehicles used in the space programmes, and also for the manufacture of bearings."

Jan 1, 1977

By J. Flemming, R. O. Burt

"The Tanco pegmatite is located in the Bird River greenstone belt of southeastern Manitoba approximately 160 km northeast of Winnipeg (Figure 1). This pegmatite body was discovered in 1929 and subsequently attempts were made to exploit it for tin by Jack Nutt Mines Ltd. and later in the middle 1950's by Montgary Oil Ltd., who extensively developed but did not produce from, its lithium deposits. In 1966 systematic investigation of the pegmatite as a potential source of tantalum led to the founding of Tantalum Mining Corporation of Canada Ltd. (TANGO) in 1967 and production of tantalum concentrates from the Bernie Lake mine commenced in 1969. Tanco is currently jointly owned by Hudson Bay Mining and Smelting Co., Cabot Beryl co Inc. of Boston, and the Province of Manitoba. (Williams and others 1978, Burt 1979, Burt and others 1982), continued until the end of 1982, when, due to falling demand and prices, operations were suspended.During the 1970's Tanco had investigated the potential of the lithium orebody; carrying our research into both the concentration of the ore and into the production of lithium chemicals. However lithium chemicals were in an over-supply situation, due in part to the production from Chilean brine deposits (Buckley, 1983), and Tanco' s own plans were put into abeyance. The potential alternative market, the direct use of concentrates in the glass and ceramics industry, did not at the time justify the cost of constructing a new plant."

Jan 1, 1986

By S. Nagamatsu

Alumina supported gold catalyst prepared by spray reaction method (spr) provides gold particle with about 20 nm of diameter. The gold particle size is larger than conventional gold catalysts. However, the spr catalyst shows higher catalytic activity for NO-CO reaction. In the present paper, we have discussed the local structures of spr-Au/Al2O3 catalyst by using Au L3-edge XANES spectra. In order to investigate the local structures of Au-sites, multiple scattering approach to XANES analysis was applied. Calculated Au L3-edge XANES spectra for fcc-Au and Au2O3 were in good agreement with the observed spectra. XANES spectra for spr-Au/Al2O3 were characterized by 4 types of Au sites (bulk, interface, surface and peripheral). In this case, almost all gold sites (> 90 %) are bulk site. The other sites are less than 10 % of gold particle. However, the experimental and the calculated results of Au L3-edge XANES spectra for spr-Au/Al2O3 require about 30 % of gold oxide or hydroxide. Bulk of Al2O3 contains a certain number of gold nano-particles, which was incorporated in the bulk Al2O3 support. In the interface area, gold oxide forms a few layers. This result was also supported by DV-Xa electronic structure calculations. The comparison of the catalytic activities of the spray catalysts and the impregnation catalyst for the NO-CO reactions imply synergy effects between gold nano-particles and alumina support.

Oct 1, 2003

By Dan Marshall, David H. Watkinson

Abstract - Cobalt, Ontario, is renowned for the 12.6 billion grams (445 million ounces) of silver produced from the area since discovery in 1903 by workers of the Timiskaming and Northern Ontario Railway. Native silver generally occurs with cobalt arsenides and sulfosalts in near-vertical carbonate veins cutting the Huronian sedimentary rocks of the Gowganda Formation, the Archean metavolcanics and/or the Nipissing diabase. All major deposits have been found within a few hundred meters of the unconformity between the Archean and Huronian rocks in general proximity to the Nipissing diabase and volcanogenic sulfide mounds within the Archean meta-volcanics. Silver has been mobilized from one or more of the local country rocks by hyper-saline brines and deposited in or near zones of mixing where the saline brines encounter paleometeoric water transported to depth along the unconformity or local structures. Previous work has shown that chloride complexes are the dominant ligands responsible for silver transport. These hypersaline brines, represented as halite-bearing fluid inclusions at room temperature, have been trapped as primary fluid inclusions within vein minerals. Pressure-temperature conditions of vein formation have been derived from mineral equilibria, maximum lithostat and fluid-inclusion studies. These data are consistent with vein formation occurring over the temperature range 300°C to 350°C, with pressures constrained between 60 Mpa and 136 Mpa (600 bars and 1360 bars).

Jan 1, 2000

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016

By E. S. Yan, R. Graley

"The StackCell was developed to overcome the engineering and design challenges that are commonly associated with existing flotation technology such as pneumatic, self-aspirating cells, mechanical cells, and flotation columns. These challenges include high energy consumption, large floorspace requirements, and size. They are most evident when designing systems to process streams containing a high volumetric flow rate coupled with a significant float yield. Unlike many metalliferous and industrial mineral applications, fine coal flotation circuits are typically characterized by feed streams containing a low solids content (<5%, by weight) where up to 85% of the feed can report to the product launder. With input from major engineering houses and end-users, the Eriez Flotation Division (EFD) developed the StackCell technology with the goal of providing an additional flotation option for end-users. This technology was designed specifically to overcome these challenges by providing an efficient method of separation in terms of metallurgy, but also with respect to equipment size, energy consumption, and installed costs. Besides being placed in tandem with existing cells to provide cost-effective supplemental capacity, this technology can be installed in a stand-alone arrangement as recently demonstrated at Patriot Coal’s Kanawha Eagle preparation plant. This manuscript provides an understanding of the underlying fundamentals of this new technology and presents data from Kanawha Eagle in addition to other industrialscale installations.INTRODUCTIONOver the past decade, column flotation has continued to gain acceptance as an alternative method for recovering fine coal due to superior metallurgical performance as compared to mechanical flotation cells. This point has been proven on numerous occasions by comparison of plant flotation data with the release analysis separation curve (Dell et al., 1972). Data from a release analysis test approximates the ultimate flotation response of a coal sample. In North America, a number of investigations have been published that document bottom-line improvements achieved using column cells (Luttrell et al., 1999; Kohmuench et al., 2004; Baumgarth et al., 2005). According to these reports, the benefits are derived from an overall increase in plant yield that can be achieved due to the improved product grade in the flotation circuit. In particular, the application of wash water to a deep froth utilized in column flotation minimizes the nonselective recovery of high-ash ultrafines that are hydraulically entrained in the froth by conventional flotation machines."

Jan 1, 2013

By M. W. Grabinsky

Better in situ performance data is required in order to advance the rational geomechanical design of cemented paste backfill systems. A few in situ test programs have been conducted, but these have suffered from too few measurement locations within the stope and have not used enough different types of transducers to fully capture the information of significance. In this paper the important geomechanical design aspects are listed, the underlying physical phenomena are described, and some previous in situ measurement efforts are reviewed. A new approach to in situ measurement campaigns is then described including measurement techniques, locations, and the logistical aspects of mobilizing transducers in an active mining environment. A work-in-progress is used to illustrate the principles and concepts involved.

May 1, 2007

By P. V. Avotins, I. Djurkovic, D. R. Nagaraj, M. Grunjic, A. Day

"As part of a major reconstruction and expansion of the Majdanpek Copper Mine, an investigation and optimization of the flotation collector regime was undertaken. The flotation response of the major minerals to various reagents and the effect of pulp chemistry was studied from both a fundamental and practical point of view. These studies led to plant trials and the eventual adoption of a modified collector suite which improved both copper and gold recoveries.INTRODUCTIONThe Majdanpek Copper Mine processes 40,000 tons per day of ore containing about 0.43% cu. In addition to copper, the ore also contains recoverable quantities of molybdenite and gold. The mine has been in operation since 1961 and is the largest in Yugoslavia. It is currently undergoing major reconstruction and expansion. The flowsheet of the Majdanpek concentrator is shown on Figure 1.The ore body is variable in composition and changes in mill feed require proper control of operating variables to achieve the optimum metallurgical results. A detailed study including grindability, flotation response, and solid-liquid separation was carried out on several samples of the ore. Flotation response and the choice of reagent chemistry were found to be very important in achieving the highest recoveries of metal values. An automatic reagent control scheme insured that optimum dosages were used in the plant.The flotation collectors used at the present time include sodium isopropyl xanthate (SIPX), AERO 3302 Promoter and AERO 5415 Promoter. The addition of AERO 5415 to the reagent suite is a recent development and was based on the favorable results obtained in the extensive laboratory testing program conducted to establish the optimum reagent combination and dosages. Subsequent plant tests confirmed that AERO 5415 provided significant improvements in copper and gold recoveries. A description of the mineralogy of the Majdanpek ore and details of laboratory and plant metallurgical data are given in this paper. The chemistry of AERO 5415 Promoter and its interaction with minerals relevant to Majdanpek ore are also discussed."

Jan 1, 1992

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By Ernie Doell, Trung Nguyen

"In early 1995 Cluff Mining commissioned a newly constructed high density tailings thickener at its Cluff Lake uranium mill. The 85 ft diameter high density thickener is one of the first of its kind in North America, and incorporates the novel paste technology in its design to produce densified (in the range of 60 -65% solids) mill tailings suitable for stable deposition in the tailings management area. This paper discusses the impetus behind the installation of such an unconventional thickener, and the many trying experiences in making it operational.IntroductionCluff Mining, a wholly owned subsidiary of Cogema Resources Inc., is the operator of a uranium mine and mill complex at Cluff Lake which is located in northern Saskatchewan. Since 1980, the company has developed and mined out several different ore bodies within the Cluff Lake region for the production of uranium concentrates, commonly known as yellow cake. Based on the known ore reserves, the Cluff Lake operations are projected to last till the early 2000's.Tailings from the Cluff Lake mill have been discharged to a tailings management area consisting of a tailings pond and two facilities for primary and secondary treatment systems. The tailings pond has an impervious bentonite lined dam, and it is divided into a solids and a liquids holding areas. Until the beginning of 1995, the mill tailings were discharged in two separate lines to the solids pond; one line carried the slurry residue of 45-50% solids (w/w) from the CCD circuit, and the other discharged raffinate tails containing less than 1 % (w/w) gypsum precipitate. Supernatant in the solids pond is treated in the primary treatment system prior to discharging to the liquids pond. Figure 1 shows the site plan of Cluff Lake tailings management area.It has been estimated that by the end of 1995 the solids pond would be filled to about 60% of its design capacity, and probably would be full before the year 2000. Therefore, Cluff Mining had to consider a more efficient tailings disposal method that could extend the service life of the existing Cluff Lake tailings management area. A high density tailings thickener was believed to be the most practical and economical system for tailings disposal at Cluff Lake mine."

Jan 1, 1996

By J. S. Phipps, D. R. Skuse

"Aqueous slurries of fine particle size calcium carbonate are used in a diverse range of end-use products. In many cases, the end use performance is governed by the fineness of the particle size distribution. In turn, the maximum fineness of the particle size distribution is primarily determined by the efficiency of the dispersants used during the production process. Here we report the sodium polyacrylate mediated dispersion of calcite and kaolin. Firstly, we report a colloid chemical description of the dispersant behaviour and attribute the stabilisation to both steric and electrostatic mechanisms. Secondly, we describe how the understanding developed in the first part of the study can be utilised to produce more effective dispersant systems which allow the preparation of, added value, higher solids and finer particle size calcium carbonate slurry products.INTRODUCTIONConcentrated aqueous dispersions of fine, particulate kaolin and calcium carbonate are used extensively in the coating of paper. Currently more than 10 million tonnes of such dispersions are used annually in North America and Europe alone, and worldwide consumption is growing at around 3% per year.Generally, paper is coated to enhance its visual appearance. Firstly, coatings improve the optical properties of the blank sheet, i.e. its brightness (or whiteness), opacity and gloss. Secondly, they improve the physical properties of the sheet that will influence the quality of the final printed image, such as surface smoothness, porosity, and ink absorption. In order to achieve these aims economically, paper coatings must be applied at high speeds and with minimal drying costs.Kaolin and calcium carbonate pigments are the major components of most paper coating formulations. Particle size distributions are chosen to maximise the optical benefits that they confer, and to allow the production of formulations that can be easily pumped, handled and coated. Coating pigments are generally produced and transported as slurries, and so it is important to obtain dispersions with the highest possible solids content, both to minimise drying costs and the quantity of water transported. This paper examines the dispersant technology that is currently used in the industry and the mechanisms by which it functions, and illustrates ways in which this technology has developed and could be further improved in the future."

Jan 1, 2003

By Patrick M. Y. Waye

As mines utilise more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with high speed data at 30 Mbps and the other for mine wide evacuation and safety applications. The high speed data system incorporates stateof- the-art data networking technologies and the existing leaky cable narrow band radio channels. The new system provides over the same basic infrastructure the high speed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow band radio channels. The second system is a system for mine wide evacuation with "through the earth" communication infrastructure. Emergency situation can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, regular reporting from miners working alone.

May 1, 2001

By Xie Qiang

It is known that the stress state inside rock discs under Brazilian tests is neither simple compression nor tension, but a complex combination of both stress types, as well as for a beam subjected to bending, where compressive and tensile stresses are separated by the neutral axis. In this study, AE generation was obtained on pure white marbles from south Portugal that were submitted to both Brazilian and bending tests. Main questions to be answered were: (1) Does Kaiser effect exist in tests which create complex distributions of tension and compression? (2) Are there any meaningful differences in AE behavior of marble under Brazilian and bending tests?

May 1, 2009