Search Documents

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By J. A. Meech, R. J. Tucker

"Since the establishment of froth flotation as an effective method of mineral beneficiation there has been both academic and industrial interest in the levels of the various reagents required to perform the desired separations. Academic interest was spurred by a desire to understand the mechanisms involved - industrial interest by a need to improve the efficiency of the process. These efficiency improvements can take two forms: cost reductions due to reduced reagent consumption and/or improved separation efficiencies. The latter are indicated by either improved grade-recovery relationships for removal of a valuable mineral from gangue, or improved separation of two similar valuable minerals.The processing of lower grade ore bodies at higher tonnage rates has necessitated increased interest in both reagent consumption and metal recovery. Furthermore, the development of accurate and functional on-stream analysis equipment in the 1960's and 1970's has allowed for a better understanding of the dynamic processes involved in a flotation circuit and has required a more concrete statement of the relationships and reactions between the minerals and chemicals in the flotation pulp. Development of these relationships is necessary in order to make use of on-stream analysis to control the process at, or near its more efficient level."

Jan 1, 1984

By E. H. Smith

"The El Indio mine treats a complex mixture of copper and gold/silver ores at its plant located in the high Andes in Chile. The plant utilizes conventional crushing, grinding and flotation to produce a copper/gold/silver concentrate. Due to high levels of arsenic and antimony, the flotation concentrate must be roasted prior to custom smelting. The flotation tailings is leached and additional gold recovered from a CIP circuit. Present and future metallurgical developments are discussed in this paper. INTRODUCTIONIn late 1989, LAC Minerals purchased 65 % of Bond International Gold and as a result became controlling shareholder of the El Indio Mine through Bond and San Jose.El Indio is a world class, complex sulphide gold deposit located in the hydrothermal alteration belt of the Andes mountains in the 4th Region of Chile. The mine is located in the high Andes about 185 km east of La Serena at an elevation of 4000 meters. The 1450 workers at El Indio live in the mine camp at 3200 m and on days off are bussed to La Serena.The El Indio mine was started in 1979 by St. Joe Minerals Corp., bought by Bond in 1987 and subsequently by LAC in 1989. The mine has produced 2.7 million oz. of gold, 9.5 million oz. of silver and 170,000 t of copper since start of operation. The mill is currently operating at a rate of 2850 t/d and producing a copper/gold concentrate which is roasted to produce a copper/gold calcine and high quality, saleable crude AS2O3 . A small proportion of the precious metals are also produced as bullion from the leach circuit.Total production during 1989 was 224,197 ounces of gold, 1,309,342 ounces of silver and 26,968 tonnes of copper. The average cash cost of production for the period was U.S. $96 per ounce of gold, net of by-product credits. The average realized price was $5. 30 per ounce of silver and $1.14 per pound of copper."

Jan 1, 1991

By A. Wright, P. Lacombe, R. del Villar, D. Hodouin, C. Sepulveda

"The data acquisition from industrial plants is a fundamental step for process modelling in process optimization, process analysis and automatic control.The introduction, some years ago, of modern distributed control and data acquisition systems in concentrators imposes a new approach in designing experimental schemes for data acquisition campaigns and new criteria for the treatment of the obtained discrete information.This paper presents the methodology applied to sample a zinc flotation circuit at Les Mines Selbaie, Joutel, PQ. Values of 85 process variables were obtained form the Distributed Control and Data Acquisition System (Bailey Network 90) and transferred to the DOS environment. Another 11 variables (flowrates and valve positions) were directly sampled using an IBM-PC compatible computer equipped with a data acquisition card and a signal processing circuit.All variables, under the vector form, were processed in the PC-MATLAB environment to either filter or eliminate the non-linear disturbances and noises, producing useful data for model development. The filtering algorithms are also presented.INTRODUCTIONProcess control does not need to be justified. Whether manual or automatic, any processing plant requires some form of control to accomplish its main objectives: a good quality product and a target throughput. Process control of mineral processing plants has steadily evolved from manual control, where the operator skills and/or experience play an important role, to some level of automatic control, usually considered better, as less human subjectivity is involved, at least when actions have to be taken.The design of these control systems requires the knowledge of the dynamics of the process it is deemed to control. Process modelling is therefore an essential step in the assessment and the design of a control strategy. The choice of model will depend on the available resources and manpower."

Jan 1, 1991

By M. Leroux, P. Lacombe, S. R. Rao, J. Y. Kim, J. A. Finch, G. Labonté, N. Macminn, M. Ounpuu

"Laboratory investigations on two complex ores, the A1 zone ore from Les Mines Selbaie and the Lyon Lake ore from Mattabi Mines Ltd. (Division of Noranda Minerals), have been carried out to determine some of the main variables in collectorless flotation. In particular, the effect of pulp potential (controlled by gas composition), conditioning time, pH and grinding media have been studied.Chalcopyrite showed the greatest response to collectorless flotation among the four major sulphide minerals present, followed by galena. Flotation of sphalerite was variable from minimal to important depending on the mineralogy and the pre-treatment performed. Appreciable silver recovery was achieved collectorlessly for the Lyon Lake ore while it could not be achieved for the A1 zone ore of Les Mines Selbaie. It appears that the difference between the two ores is related to silver's predominance as tetrahydrite in the Lyon Lake ore while it is as argentite and native silver in the A1 zone ore.The response of the ores to collectorless flotation is strongly dependent on the pulp potential, Ep, and pH. Using different gas compositions and different conditioning times it was found that collectorless flotation occurs when Ep is +195 to +295 mv (vs SHE). The actual on-set potential for collectorless flotation is dependent on the ore. A too high potential or prolonged oxidation leads to a decrease in selectivity. Some other factors were examined, notably the effect of pH and the type of grinding media on the selectivity achieved in the laboratory.Preliminary results from a plant trial at Mattabi Mines Ltd. confirmed that collectorless flotation occurs and that it is preferential for chalcopyrite and to a lesser extent galena. Collectorless flotation was not attempted at Les Mines Selbaie. However, examination of the distribution of collector between the different addition points in the copper circuit suggests that it may be present."

Jan 1, 1990

By C. Larsen, D. Fragomeni, A. Vien, D. G. Fisher

"MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling errors, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law.This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance."

Jan 1, 1991

By T. J. Yeomans

"The Kidd Creek metallurgical site is situated twenty-six kilometres east of Timmins, Ontario. The site consists of a 4.5 niillion tonne per year concentrator, a 127,000 tonne per year electrolytic zinc plant and a 79,000 tonne per year copper smelter/refinery complex.The concentrator commenced operations in 1966 and was expanded to its present capacity in 1978. The zinc plant commenced operations in 1972, and the copper smelter/refinery in 1983.The concentrator tailings, and both liquid and solid waste products from the other plants are disposed of within a 1215 hectare tailings disposal area. Here, a method known as centraljzecl thickened discharge is used to form a stable cone-shaped hill. A low permanent perimeter dyke structure encloses the cone and directs cone run-off and thickener overflow to a treatment pond. After treatment with lime slurry, this neutralized effluent is recycled to the metsite and also discharged into the Porcupine River system.The tailings system has been in operation in its present form since 1972, upon completion of dykes and a 110 metre thickener unit. Underflow densities were continuously increased until thickener overloading became a serious problem. This necessitated the construction of a second 110 metre thickener, which was completed in 1983. Target densities have been achieved without difficulty since then.This paper discusses the operation of the tailings system, reviews past performance, and outlines future operations."

Jan 1, 1986

By Patrick Pelletier Jr., Pierre-Alexandre Bossé, Gianni Bartolacci, Ian Orford, Steve Parent

"Over the last decades, many authors have shown the importance of froth in the flotation process. Mineral recovery is related to froth recovery and flotation. Selectivity is affected by froth characteristics, especially structure and loading. The characteristics of froth textures could therefore be used for diagnosing flotation.Machine imaging, especially image texture analysis, allows on-line measurement of important froth characteristics and process state classification. The measured characteristics include froth texture, loading and stability indicators. To extract information from images, texture analysis tools are used as well as a block-matching algorithm (BMA). For process state classification, images are analyzed with the same tools and clustering is done with multivariate data analysis algorithms.Two case studies, Brunswick Mine Concentrator Cu/Pb circuit and LaRonde Mine Zn circuit, are presented to show that these indicators may be used for diagnosis and control. The influence of manipulated variables on measured froth features is shown as well as the relationship between froth characteristics, mineral recovery and flotation selectivity.INTRODUCTIONImaging is a way to depict abstract characteristics of a scene or an object; it is often related to other types of scientific observations, chemical component concentrations, for example (Geladi and Grahn, 1996). In this paper, the scene is flotation froth. Imaging can be especially useful in applications where it is difficult to obtain the measurements needed for process analysis – froth flotation, for example."

Jan 1, 2006

By Pierre Lacombe

"The operation of the Louvicourt Mine will have to rely on stringent grade control and on the optimization of the amount of blocked ore made available per given development effort. All of the above being necessary to obtain the highest throughput at the lowest mining cost.To assist in achieving these objectives, the need for production of a competent fill with short curing time was recognized early by the project partners. As well, operating costs associated with the selected method should be as low as possible while meeting the technical criteria.A feasibility study comparing filling methods showed potential benefits in all aspects of the paste fill use, except for its higher capital costs and increased operational complexity. This last consideration was tackled by the conservative design approach adopted in the flowsheet development of the paste fill plant.Since commissioning of the plant has just been completed at this time, the paper will focus on the feasibility study and its background, the design of the plant and testwork results at pilot plant and plant scale.RésuméLe succès de l 'opération de Louvicourt Mine dépendra d' un contrôle serré des teneurs du minerai et de la maximisation de la quantité de minerai développée par effort uni ta ire. Ces critères devant etre respectés afin d'obtenir le taux de production le plus élevé au coût le plus bas.De façon à satisfaire ces contraintes, les partenaires du projet ont reconnu tôt la nécessité de produire un remblai de qualité tout en maintenant un temps de curage court. De plus, les coût d'opération associés a cette opération se devaient d'être des plus avantageux sans sacrifier l'atteinte des objectifs techniques.Une étude de faisabilité comparant différentes méthodes de remblayage a démontré que le remblai en pâte offre des aspects positifs sous taus les angles, si ce n'est de son coût en capital initial élevé et de sa complexité relative d'opération. Ce dernier point fut considéré de près par l'adoption d' une approche conservatrice lors de la conception de l'usine de rernblai.Puisque la mise en service de l'usine n'a été faite que les détails de l 'étude de faisabilité et ses fondements, 1 'usine et des résultats d' essais obtenus a l'échelle de l'usine seront discutés."

Jan 1, 1995

By P. D. R. Maltby

"With the narrow vein structure of Nova Scotia gold deposits, selective mining is rarely possible and mill heads will be too low (below 0.10 oz per ton of gold) to support a conventional mill of up to 1000 ton per day capacity at present gold prices. The recent operation of a small 100 t.p.d. mill at Cochrane Hill using fine grinding - leaching - filtration supported this assertion. Milling costs exceeded $25.00/ton of feed mainly due to high capital, labour and maintenance costs.Accordingly, since 1981, efforts have been directed towards the development of a cheap gold extraction process in terms of both capital and operating costs. The main criteria is to produce gold below US $200 per oz including all administration, mining and process stages. This paper describes such a process development for Cochrane Hill. LOCATION AND HISTORY OF THE PROPERTYThe Cochrane Hill property is located about 8 miles North of Sherbrooke, N.S. on highway No. 7. Sherbrooke is about 180 miles east of Halifax. Gold was originally discovered at Cochrane Hill in the 1860's. Early work consisted of trenching. In the 1930's a small shaft was sunk to about 80 feet and some tonnage treated using a stamp mill with gravity concentration of gold.Northumberland Mines Ltd. acquired a 70% interest in the property in 1977. Subsequent drilling indicated a potential zone of gold mineralization with a drill-indicated tonnage of one million tons having a grade of 0.07 ounces per ton of gold (all high assays cut to 1 oz) down to a depth of 300 feet recoverable by open pit mining methods. In broad terms, the goldbearing zone is about 50 feet wide and 800 feet long and dips at about 70°."

Jan 1, 1984

By David Rahal, Des Erasmus, Ken Major

"Over the past twenty years there has been an increased emphasis on fine grinding in the minerals industry. This spurred the development of a range of new fine grinding equipment in the 1990s. At that time, the Knelson-Deswik mill was developed in South Africa for the pigments industry.Knelson Milling Solutions currently offers a wide range of laboratory, pilot and production scale mills. These mills bridge the gap between traditional low speed vertical mills and the high speed horizontal mills (tip speed < 3 and > 15 m/s respectively). They are designed to run at tip speeds between 10 and 12 m/s and are capable of operating with very dense grinding media. The result is a power intensity that is higher than the low speed mills and overlaps that of the high speed mills. This allows the mill to be customized for a wide range of grinding applications.A case study at Aquarius Platinum’s Kroondal Mine shows that the Knelson-Deswik technology can produce a consistent product size despite feed variations. It also shows that the throughput was proportional to the slurry density at Kroondal. The case study identified increasing the slurry density as a process change that can increase throughput and reduce the specific energy consumption.INTRODUCTIONThe increasing complexity and finer grain sizes of modern ore bodies have increased the importance of effective mineral liberation in obtaining acceptable grades and recoveries (Jankovic, Valery and La Rosa, 2003; Lichter and Davey, 2006; Napier-Munn, Morell, Morrison and Kojovic, 1996). This trend has increased the significance of fine grinding technology because the input energy increases exponentially as the required product size decreases from 100 to 10 microns (Gao and Weller, 1993a).The US Department of Energy recently provided the context for the potential energy savings in the US Mining Industry (BCS, 2007). They reported that grinding consumes approximately 494 TBtu/year. This was over double the consumption of the second highest equipment category, diesel materials handling systems (211 TBtu/yr). The proportion of grinding energy allocated to fine grinding can only be expected to increase as finer ore deposits are mined. It is therefore critical that fine grinding efficiency continue to improve through the selection of appropriate equipment and the development of best practices for existing applications."

Jan 1, 2011

Burr Mineral Resource has: ?Grade / Thickness / Tonnage ?Dry Caprock ?Low Carnallite ?Low Clay / Insolubles ?Flat & Continuous Deposit ?Proper depth

May 1, 2009

By R. F. Hochstein, A. J. Neale, B. C. Flintoff

"Process control technology holds very significant potential benefits for many mineral and coal processing plants. The impact can be expected in terms of performance improvements (e.g. increased throughput, better quality control, higher availability), through reduced operating costs (e.g. lower reagent consumptions, manpower reductions) and in the form of intangibles (e.g. reduced vulnerability to manpower turnover, increased productivity in the user group). However, the installation of a process control system will represent considerable capital expenditure and will generate an operating cost. No management team would approve the funding for such a project without some reasonable measure(s) of the profitability of a proposed system. This paper describes a methodology for addressing the justification problem. Of particular interest is the approach to quantifying performance improvements, frequently found to be the predominant benefit of process control.INTROPUCTIONProcess control has become widely recognized as an essential component of any processing operation. It has direct impact on productivity, process efficiency and product marketability. The reported pay backs associated with successful installations underscore this observation. As a consequence, many operators who have little in the way of process automation are looking to initiate control projects, while those who currently enjoy some level of automation are looking to upgrade existing control systems (= process + instrumentation + hardware + software + operators + support). While the emphasis here would appear to be on retrofit process control projects, new plants, or those currently in the design stage, will usually find themselves in one of these categories shortly after startup 1."

Jan 1, 1990

By M. W. Lewis

A mine&apos;s inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine &rsquo;s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By M. W. Lewis, B. Sambirsky, J. Werner

A mine’s inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By M. Beth McClenaghan

This paper summarizes diamond exploration techniques used in glaciated terrain, focusing on indicator mineral and geochemical methods applied to glacial sediments. Understanding the ice flow history, depositional history, and stratigraphy of glacial sediments are essential to successful sampling, interpretation and follow-up of indicator mineral and geochemical anomalies related to kimberlites. Kimberlite indicator minerals survive glacial transport over long distances and the relative abundance of each mineral in till is a function of the primary mineralogy of individual kimberlites. Indicator mineral distributions observed at a regional scale define the net effect of glacial dispersal, often along different ice flow directions. Local-scale distributions define individual dispersal trains. The medium sand (0.25 to 0.5 mm) fraction of heavy mineral concentrates prepared from glacial sediment samples is best suited for indicator mineral surveys. The application of till geochemistry to diamond exploration is increasing because it is significantly cheaper than indicator mineral analysis and it can be performed quickly. The <0.063 mm (silt+clay) and 0.5 to 2.0 mm (coarse sand) fractions provide the best geochemical contrast between background and kimberlite-rich till. Kimberlite pathfinder elements that provide good contrast include Ni, Cr, Ba, Co, Sr, Rb, Nb, Mg, Ta, Ca, Fe, K, Ti and REE, the relative importance of which will depend on kimberlite composition as well as that of the surrounding bedrock.

May 1, 2002

By Peter Rubie, Toni Kojovic, Fengnian Shi

"Mining companies have recognized that characterization of ore breakage plays an essential role in the design and optimization of comminution circuits.Recently the Julius Kruttschnitt Mineral Research Centre (JKMRC) has developed a new breakage model incorporating the effect of particle size, and a new breakage characterization testing device, called the JK Rotary Breakage Tester (JKRBT), which allows rapid testing of particle breakage under high energy single impact and low energy repetitive impact conditions.Positive feedback received from mining company sponsors to the new technology has prompted the JKMRC to further validate the device and the model through a formalized validation program using machines designed and manufactured by Russell Mineral Equipment (RME). The first unit was installed and commissioned at the Anglo Platinum laboratory in Johannesburg in March 2007 and four more major mining companies will participate in the validation program in 2008, including Barrick, BHP Billiton, Rio Tinto and Teck Cominco. The results from validation tests at the JKMRC and Anglo Research have shown that the JKRBT generates statistically similar breakage parameters to the traditional Drop Weight Test, but with significant advantages over its predecessor. Application of the JKRBT in geometallurgical testing with the AMIRA P843 GeM project has confirmed the JKRBT device offers a rapid and consistent method for determining the hardness of drill core samples. The JKRBT has the potential to revolutionize ore testing, with applications in laboratory impact breakage characterization of rock samples, drill cores, coal and other materials. It also stands poised to significantly advance the process control and management of comminution circuits since the concept is readily adaptable to on-line ore hardness measurement.INTRODUCTIONMining companies have long recognized that the performance of a comminution machine such as a crusher or an autogenous / semi-autogenous grinding (AG/SAG) mill depends not only on the machine operating conditions, but also on the “hardness” of the feed material to be broken. This recognition has driven significant interest in laboratory particle breakage characterisation and testing. The laboratory breakage characterization tests can be roughly classified in two broad groups based on their primary breakage modes: tumbling and impact/compression. The famous Bond ball/rod mill tests (Bond, 1952 and 1961) represent the typical tumbling test and have become the industry standard for estimating the specific energy (kWh/t) of rod and ball mills. However, as the energy application in the single particle impact tests can be well defined and controlled, the latter have received significant attention in the last 30 years. It was estimated that mining companies worldwide spent over three million US dollars on single particle impact breakage characterization testing in 2006."

Jan 1, 2009

"At a current mining rate of 3,750 tons per day, La Mine Doyon is currently the largest gold mine in Canada. La Mine Doyon is an open pit gold mine located in the Abitibi area of Northwestern Quebec. The project is a joint venture between Soquem, a Quebec Crown Corporation in the resource development field and Lac Minerals Ltd., a publicly-held, resource development company. Lac Minerals is the managing company and operator of the project.Doyon went into production in 1980 on a very limited basis at 600 tons/day, and has seen a step wise increase to the current rate of 3,750 tons/day. Initially, all the ore was processed at Noranda Mines, Horne Division as flux for the copper smelter. The East Malartic Mill in Malartic was then upgraded and began processing Doyon ore. The third step in the progressive increase of throughput was the commissioning of the Doyon mill in November of 1982. Doyon ore is currently being processed at all three locations.During 1983, an exploration ramp was driven to explore the ore below the ultimate pit depth. Current plans indicate the sinking of a shaft and the commencement of underground mining during the next 2 or 3 years.Since its humble beginning, La Mine Doyon has always been a success; ore reserves have been extended to the east and the west and will soon be confirmed at depth, the mining and processing rates have been increased 6 fold, and the recovery has been increased from a designed recovery of 85% to over 95%. The intent of this paper is to trace the history and reasons for these rather dramatic improvements."

Jan 1, 1984

By K. Norris

"The Campbell mill has undergone numerous changes over the past 43 years. However the rate of change has increased significantly in the last 4 years. A new grinding circuit, carbon-in- pulp circuit, pressure oxidation plant, and column flotation circuit are all new additions. Other changes have occurred in the last 2 years including a large reduction in sodium cyanide consumption, and the introduction of a computer controlled grinding circuit. More improvements are planned in the next 2 years. Some of these improvements include the construction of an effluent treatment plant, and the replacement of filtering and Merrill-Crowe precipitation with carbon-in-leach and electrowinning.Recent changes and improvements to the Campbell mill are a commitment by Campbell mill personnel and Placer Dome Inc. to decrease operating costs, increase gold recovery and gold production, improve industrial hygiene and safety, and meet environmental compliance with current government legislation.INTRODUCTIONThe Campbell Mine has been and continues to be one of Canada's premier gold mines. Campbell Mine is 100% owned and operated by Placer Dome Incorporated. Milling of ore commenced in 1949 at a rate of 300 tons/day producing 58,000 ounces per year of gold. In 1992 Campbell Mine will mill 1340 tons/day of ore at a grade of 0.6 ounces/ton, producing 275,000 ounces of gold at a cash cost of $205.00 Cdn./ounce.This paper discusses some of the changes that have been made to the Campbell mill in the past 4 years. The flowsheet has undergone extensive changes and will continue to change rapidly in the next 2 to 3 years. A simplified flowsheet of the Campbell mill is shown in figure 1."

Jan 1, 1992

By J. E. Nesset, J. A. Finch, Rosenblum. F., S. Somot

"In a previous presentation at the CMP, evidence was shown for the formation of hydrogen sulphide (H2S) in self-heating experiments on pyrrhotite-rich samples (Somot and Finch, 2006). Oxidation of H2S is strongly exothermic leading to the proposition that H2S is playing a key role in the self-heating process. Subsequently, tests in two weathering apparatus (I and II) were run under varying oxygen levels to further examine conditions leading to self-heating. To characterise their resulting self-heating capacity the samples from the weathering tests were subjected to a modified Stage B test using the self-heating apparatus developed by Rosenblum and co-workers (Rosenblum and Spira, 1995; Rosenblum et al., 2001). Results showed highest self-heating after weathering occurs under low oxygen conditions, supporting the H2S hypothesis. It was observed that highest heating rates are not directly related to highest weight gains of samples.INTRODUCTION“Sulphides” refer to several types of minerals containing sulphur in its lowest oxidation state of - 2. Self-heating is the spontaneous heating of a material without external heat input. It is well established that some sulphides will self-heat on exposure to moisture and oxygen (Farnsworth, 1977; Good, 1977; Rosenblum et al., 2001; Wu and Li, 2005). This process is highly exothermic and if the heat generated is not dissipated, combustion may occur when the temperature reaches the ignition point of the sulphide (typically 350-400 °C). The hazards of sulphide self-heating range from handling hot material, to sulphur dioxide release, to fires. The literature documents self-heating incidents underground, on ships and trucks transporting sulphide concentrates, and in mine waste (tailing) disposal areas (Stachulak, 1990; Lukaszewski, 1969; Headley et al., 1977). Lukaszewski (1969), Farnsworth (1977), and Good (1977) note that sulphide minerals can act as fuel to promote underground mine fires. Based on such findings, sulphide minerals could become classified as hazardous materials, making transport of concentrates and storage of mine waste subject to stricter and more costly regulation. The problem is one the industry is keen to avoid."

Jan 1, 2009