Search Documents

By J. Aydt, W. McCombe, H. McLaughlin, L. Nightingale-Mercer

The McClean Lake mill is located approximately 850 kilometers north of Saskatoon, Saskatchewan, Canada and is operated by Orano Canada Inc. (Orano). The mill was designed to process high grade uranium ores, and in 2014 completed a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum. This expansion included significant changes to the mill’s secondary leach circuit in support of safely processing high grade ore directly from the Cigar Lake mine. In particular, inter-stage pumps were introduced for slurry transfer between the secondary leach tanks, replacing the original pressure feed forward operation. The design and selection process for these pumps was strongly influenced by the uncertainty related to actual radiation dose exposure when processing undiluted high grade ore (up to 30%U), and consequently the desire to maintain minimal occupancy in the vault enclosure containing the secondary leach tanks. These constraints resulted in the decision to install positive displacement pumps above the leach tanks in a suction-lift configuration. Operating experience with this design has shown that the pump capacity is significantly de-rated due to process solution gas-entrainment and pipe scale build-up, particularly in the front end of the secondary leach circuit where reagent dosage is high. Experience processing high grade ore also provided accurate radiation dose data to demonstrate that the level of occupancy in the leaching vault enclosure could be re-evaluated to accommodate alternate pump configurations. This paper reviews the lessons learned and improvements made to safely increase the capacity and reliability of the leach inter-stage pump system.

Jan 1, 2020

By S. J. van Rensburg

Competition for resources, including water and arable land, refocused attention on water and gold tailings management with respect to quantity and quality. MINTEK established and validated an "Advanced Leach Facility" to record kinetic leach information aimed at gold refractory sulphide ores. This facility was developed because of the need for additional leach process information to enable proactive decision making. Instead of focussing on optimised gold recovery only, the impacts of pre-oxidation methodologies were evaluated by considering key parameters, including cyanide speciation, reagent consumption, thiocyanate, arsenic, heavy metals, salt loads, water quality and residue stability. Results from oxidative leaching of a refractory gold ore employing oxygen, ozone, ultra-fine grinding, high shear and pressure oxidation are discussed. The relative cyanide and lime costs and environmental and sustainability effects associated with these technologies are briefly outlined.

Jan 1, 2011

By A. A. Bakke

"The Fort Knox gold deposit is hosted within the Fort Knox Pluton, a Cretaceous multiphase granitic body that intrudes the Fairbanks schist. Gold occurs along the margins of stockwork veins and veinlets, quartz-filled shear zones, and along fractures within the granite. The mineralization is generally sulphide-poor and closely associated with trace amounts of bismuth, tellurium and to a lesser extent with molybdenum and tungsten. At present, proven/probable reserve estimates, based on a cutoff grade of 0.39 g/t Au, are 158.3 million tonnes grading 0.83 g/t Au.The Fairbanks schist comprises the bulk of the country rock. The dominant lithologies present include muscovite-quartz schist and micaceous quartzite. Immediately north and south of the main orebody, mixed metamorphic lithologies of the Cleary sequence, a subunit of the Fairbanks schist, have been mapped. Development of local zones of weakness, most likely due to a broad regional warping event, resulted in brittle-ductile deformation and activation of a northwest-southeast shear couple between contrasting lithologies.The Fort Knox Pluton consists of at least three phases based primarily on textural differences. Intrusion of a fine-grained granite was followed by a medium-grained porphyritic granite. The youngest intrusive phase is a coarse-grained, seriate porphyritic granite, the Vogt Stock. The Vogt Stock forms an elongate dome with the axis in the east-west direction. Structures displayed in the overlying units, believed to be the result of doming, include tension fiSSUres and longitudinal fractures.Premineralization fractures, the result of the magmatic doming, provided conduits for initial stockwork quartz vein development and quartz enrichment in shear zones. Weak development of vein-controlled phyl/ic, potassic, albitic, and argillic alteration styles are present. Evidence of a late thermal event resulting in a low-temperature alteration assemblage of calcite + zeolite (stilbite) + chalcedony + clay occupies breccia zones, joint surfaces, and fractures within the granite."

Jan 1, 1995

By M. Bozorgtabar

Metal Matrix Composites (MMC) have a ductile matrix containing ceramic particles, Due to their improved wear properties, Al?SiC composites have economical applications in many industrial uses where wear is a problem, One of the most serious difficulties in manufacturing Al-SiC composites is obtaining adequate 'wetting' of the particles by the melt. In this research work, a stir casting system was designed for the improved manufacturing Al-SiC composites, The effect of some production variables such as the addition of SiC particles to the aluminum melt on wettability, was also studied. The results showed that the manual addition of particles would not be successful in manufacturing and that a system of adding silicon carbide particles through controlled temperature, atmosphere and improved mixing was needed.

Jan 1, 2005

By R. Krentz, P. D. Cordingley

The nickel-cobalt sulphides produced from limonitic laterite ores by Moa Nickel S.A. in Cuba are refined at the Corefco nickel-cobalt refinery in Canada. Major changes to the refining process were required when the Moa sulphide feed, with its unusually high cobalt content, was introduced in the early 1990's. In the period 1994 to 2005 the production capacity of the refinery has increased dramatically to match increases at Moa, and significant process improvements incorporated. The process flowsheet consists of the original ammonia leach process, optimized for cobalt chemistry and overall leaching capacity. Extraction of metal values is followed by the unique nickel-cobalt separation technology, in which most of the cobalt is separated from the ammoniacal nickel sulphate leach solution by precipitation as a nickel-cobalt hexammine salt. This salt is refined from a Co:Ni ratio of 1:1 to over 10,000:1 by selectively leaching nickel, redissolution and recrystallization in ammonium sulphate solution. Nickel and cobalt are recovered using the well-known Sherritt hydrogen reduction technology. This paper reviews the chemistry described above, examines some of the changes in operating conditions made over the years and highlights some of the recent physical changes made to the refinery.

Jan 1, 2005

By J. W. McCammon

CRANGES in construction ideas and the continually rising costs of labour and conventional building materials, particularly since World War II, have prompted widespread investigations into the development and adaptation of new materials to meet the new requirements and to help reduce costs. Lightweight aggregates have been prominent in these investigations. The lightweight aggregates most commonly used today are foamed slag, cinders, pumice, diatomite, exfoliated vermiculite, expanded perlite, and bloated clay or shah. Lightweight aggregates contribute to the building industry in several ways: ( 1) in large structures the reduction in deadweight effected by the use of lightweight materials reduces the amount of reinforcing and structural steel necessary to support the structure; ( 2) the decrease in weight of lightweight blocks makes handling easier and faster; (3) pre-fabricated floor and roof slabs and tilt-up walls of lightweight concrete have become feasible and popular; ( 4) lightweight aggregate concrete has good nailability and is easily channelled; (5) concrete and plaster made with lightweight aggregate have good heat and sound insulation properties.

Jan 1, 1957

By C. J. Edmonds

Of the gold mined in Canada over 90 percent is extracted from the ore by the process of "cyanidation". In this process crushed ore is treated with lime to provide "protective alkalinity" and cyanide, usually in the form of sodium cyanide. The gold is dissolved in the cyanide solution, which after further treatments for clarification, is precipitated by the addition of zinc dust. Wastes from the process consist of tailings which will contain cyanides. Water consumption, mill size, effluent quantity and quality are depicted in transparency (1). It should be noted that as far as the wastes are concerned it has been impossible to postulate a typical situation. Variation from the above data will occur. A summary of data from tailings pond effluents is presented in transparency (2). The figures in parentheses indicate the usual range of values for the parameter.

Jan 1, 1973

By Brennan Lang

Why Seal Tunnels? ?Restore groundwater levels to pre-mining conditions. ?Saturate rock mass to reduce acid rock drainage. ?Reduce discharge flow to the environment. ?Reduce or regulate flows to a water treatment plant.

May 1, 2002

By T. R. Chari

The safe-level dilution of low-level radioactive wastes in large volumes of selected granular material is proposed as an alternative method of permanent waste disposal to current Canadian practice of concentration and encapsulation. Accepting the fact that a "background level" of radioactivity exists throughout the world, the authors feel that the concept of controlled dilution of radioactive wastes to a level in keeping with "background" is a plausible alternative to current thinking on the subject and is worthy of equal consideration.

Jan 1, 1979

By M. Rafati

In this investigation, the effects of T4 and T6 heat treatments of AZ91 magnesium cast alloy have been studied. The effects of different microstructural details such as morphology, size and distribution of precipitates and their influence on fracture mechanisms were investigated by optical and scanning electron microscopy. The mechanical strength of the alloy after T6 treatment was found to increase in comparison to the T4 treatment, due to the formation of discontinuous precipitates in the grain boundaries. Precipitation in this alloy occurs in two ways: continuous precipitation, which nucleates and grows inside the grains, and discontinuous precipitation, which forms at the grain boundaries. During ageing, the length of the continuous precipitates increases, and, hence, interprecipitate distance decreases. The formation of discontinuous precipitates causes initiation and propagation of cracks at and the weakening of the grain boundaries. This is the principal reason for the reduction of the ultimate tensile strength in T6 heat treatment in comparison to the T4 condition.

Jan 1, 2006

By T. Gerritsen, C. Martinez, F. Stober, T Ma, J. R. Frias, M. Sedighy, J. Janzen

Electrode control systems regulate power by physically positioning electrodes. Due to the weight and inertia of the electrodes and hoist equipment, this is a relatively slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +/- 20% or more around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicana's laterite nickel furnace, yielding excellent results with a 3 to 1 reduction in power fluctuations.

Jan 1, 2005

By W. A. Alexander

Introduction In the course of a programme of research on beryllium in progress in these laboratories, knowledge of the recrystallization temperature became necessary. As the information is not available in the literature, the determination of this temperature for metallic beryllium was undertaken. By the reduction of grain size through working and recrystallization and the probable simultaneous induction of preferred orientation, it was hoped to improve the working properties of beryllium at lower temperatures. The recrystallization temperature is usually determined by observing the lowest temperature of annealing at which new crystals are formed in severely cold-worked metal or alloys. This temperature is profoundly influenced by the following factors: the purity of the metal, in the case of an element, or the composition of the alloy; the degree of straining or working; the temperature of straining; the original grain size; and the time held at the annealing temperature. The observed temperature is lowered by higher purity, more severe straining, lower temperature of working, smaller original grain size, and longer time of annealing. Beryllium presents special difficulties in that the percent elongation in tension is effectively zero, so that ordinary squeezing or rolling was not possible. A possible means of straining was suggested by the fact that indentation hardness tests could be made. It was known from earlier work that the metal could be worked at elevated temperatures, so that working at the lowest feasible temperature and quenching might also be a means of producing strain. The purity of the metal is also a point of some uncertainty in the case of beryllium. Losano has prepared 99.96% Be which appears to be the best reported. Distilled metal used in the present work approached this purity. However, by analogy with other metals, residual impurities may have a pronounced effect on the recrystallization. Further purification of beryllium would evidently entail considerable difficulties due to the highly reactive nature of the metal, and was not attempted.

Jan 1, 1947

By R. B. Humphrey

Cut-and-fill mining methods at the Thompson Mine have undergone significant changes since production began in 1961. Changes have been introduced in almost all aspects of the mining operation, from the original timbered chutes and air-operated slushers to the present-day bored raises, footwall ore passes and load-haul-dump units. This paper describes the evolution of mechanized cut-and fill mining methods, highlighting the changes in design for stopes and service openings, ground support methods; hydraulic filling and ventilation systems. A mechanized stoping area is described from the initial mining concept through design, development, construction and mining cycles.

Jan 1, 1979

By G. C. Bateman

THE cause of silicosis and its prevention have held the attention of medical men and mine operators for many years and at the present rime the study of this disease is more than ever to the fore, even though a considerable abatement in the incidence of silicosis has been noted of late. This abatement is due to individual and collective efforts. The Industry is keenly alive to the situation and much research is being carried on. Silica dust is assumed to be a contributing factor in the cause of silicosis. How it acts progressively in the early silicoric is nor fully understood. As the study advances, more effective measures of control may be evolved. At present the Industry has three known methods of reducing the incidence: 1. By thorough X-ray examination of all applicants, with special reference to chest conditions. Those who are considered to be susceptible to the disease are prevented from entering the industry. 2. Thorough ventilation of the mine. 3. Control of tuberculosis in mining centres and removal of miners when first symptoms of tuberculosis become apparent. In 1934, the Ontario Mining Association formed a Committee, known as the Technical Silicosis Research Committee, to study and supervise work on problems related to silicosis. This Committee obtained the full-rime services of a mining engineer to carry our research work at the mines in the Province of Ontario. The Ontario Mining Association has also provided funds for the purpose of carrying on research work along pathological and biological lines. This work is being done in the Department of Medical Research of the University of Toronto, in the Banting Institute, under the supervision of Sir Frederick Banting. The Silicosis Committee work in full cooperation with the doctors in the Banting Institute and provide material from the mines for the it use.

Jan 1, 1936

By Mike Smith, George Chung

"A 23 million dollar Flotation Plant has been commissioned at the Iron Ore Company of Canada in 1998. Nine OK-50 cells &re used to float silica in this 1,400 tomes per hour plant. The paper details project development, construction and operating results. This plant gives IOC the capability to produce not only high quality blast furnace pellets of varying silica, CaO and MgO levels, but also a high iron, DR grade pellet. The first activity was simply to sit down with the suppliers, Outokumpu, Wemco. GL&V and Svedala, to discuss applications and share experiences. We learnt what each supplier had to offer, what features would particularly suit this application, what options were offered, what were the materials of construction, how the equipment is maintained, which wear parts require replacement, etc., etc. We tried to learn as much about the equipment as the suppliers themselves knew. Then we tried to learn more: we contacted users and asked about any weak points, which options were worth incorporating and which items were not. We then discussed these points with the suppliers and established how potential problems might be overcome."

Jan 1, 1999

By Etienne Roy Grégoire

Since the early 1990s, the Canadian mining industry has been increasingly defined by the signing of Impact and Benefit Agreements (IBAs) between mining companies and Aboriginal peoples. While these agreements are intended to complement the legal system, they also serve to establish the legitimacy of mining projects and to encourage the harmonious integration of these projects into their social and environmental contexts. Beyond their practical implications, what are the effects of such agreements on the ability of Aboriginal communities to access the institutional space where the authorization of mining projects and the conditions of their implementation are decided? Can we view IBAs as a preliminary step towards the operationalization of the principle of Free, Prior and Informed Consent? This paper aims to explore the potential of IBAs as a sustainable solution to the legitimacy issues that result from the implementation of the formal regulatory framework governing mining activities in this jurisdiction. We highlight what constraints and opportunities the James Bay and Northern Quebec Agreement (JBNQA) engenders for local communities and draw attention to the ways in which the negotiation of the Raglan IBA and the environmental evaluation processes act upon each other. We find that certain structural problems - and problems of legitimacy ? related to mining in Northern Quebec cannot be solved by the sole signature of an IBA, which suggests the need for caution when considering such agreements as a panacea. The Raglan case demonstrates that IBAs, like other modes of regulation relying on the direct interface between companies and communities, would benefit from a stricter framework and more explicit ties with official regulation channels.

Aug 1, 2013

By Michael J. Lawrence

"The VALMIN Code was developed and formally adopted by The Australasian Institute of Mining and Metallurgy (AusIMM) in 1995 and a revision was issued in 1998. The VALMIN Code applies to all relevant reports under the Australian Corporations Law, including submissions to the Australian Stock Exchange (ASX) and the Australian Securities and Investments Commission (ASIC).The VALMIN Code and Guidelines sets standards for the preparation and commissioning of independent assessment and/or valuation reports on mineral and petroleum assets or mineral and petroleum securities.It is mandatory for AusllvI:M's members to follow this Code in these relevant circumstances and failure to do so will result in serious sanction of the member by the Ausllvllvfs Ethics Committee. Public support for the use of this Code has been given by regulators (ASX/ASIC) and market participants ( eg major accountancy firms). It is also endorsed as a guide to general best practice in project assessment and valuation.This paper will discuss how the VALMIN Code has worked in practice over the past few years. It will also examine areas where the Code could be improved and how it could form the basis of a new Canadian Code for mineral property valuation."

Jan 1, 2003

By Bergh. L. C.

On line monitoring and diagnosis systems of process operating performance are becoming an important part of industrial programs, leading to improve process operation and therefore product quality over time. In processes, such as the contact section of a sulphuric acid plant, a large number of input variables, highly correlated, are presented. These characteristics usually pose more difficulties in modelling the process for monitoring and diagnosis purposes. Multivariate statistical projection methods, such as Main Component Analysis, have been proposed to effectively deal with these situations. The application of these ideas to a section of a 2350 MTD sulphuric acid plant, located at the Caletones Smelter, including dry tower, gas blowers, catalytic reactor and S03 absorber processes, is discussed here. A PCA model with eight main components is used for monitoring and diagnosis of more than seventy operating variables. Hottelling's T2 and Q residuals test were used for detecting measurement problems in relevant variables, and for identifying which set of variables were responsible for driving the process outside its normal operating region. Furthermore, considerable information for the correction of the tested operating problems was given by the use of these techniques.

Jan 1, 2007

By Jamel Sgaoula

During 1998 COGEMA Resources Inc. announced that operations at the Cluff Lake mine will be suspended indefinitely by the end of year 2000 as a result of deteriorating uranium market conditions. To remain profitable, Cluff Lake mine started an aggressive cost reduction program. A cost reduction team was formed to look for ways to lower production costs. The focus of this team was to screen all areas and to come up with ideas to improve the economy of the mine and ensure the viability of the operations over the remaining three years of operations. Among the areas where significant savings were achieved are: (1) replacement of portion of cement with fly ash in backfill; (2) backfill optimization; and (3) new shotcrete plant installation on site for bulk in-house shotcrete production. This paper details the research work carried out by Cluff Lake mine on these projects and results of its application.

May 1, 2001

By R. L. Eadie, J. L. Luo

The effect of plastic deformation on near-neutral pH stress corrosion cracking (SCC) also known as environmentally assisted cracking was studied by cracking rate measurements. All the tests were conducted in a synthetic near-neutral pH solution. The traditional potential drop tests using compact toughness (C-T) specimens with 2-3 mm long pre-cracks showed varying plastic deformation by rolling would increase the material's susceptibility to SCC. This was confirmed by cyclic loading tests using double notched flat tensile specimens with 200-300 µm long pre-cracks which gave the same results that the specimen with large scale plastic deformation by tensile loading had a relatively faster crack growth rate than that with only small scale plastic deformation.

Jan 1, 2005