Search Documents

By Zhiye Zhao, Jianping Sun, Zhipeng Xu

"The subsea rock cavern project is an underground storage facility. For cost-effective and safe excavation, the risk caused by the groundwater seepage into the rock cavern must be addressed. As one of the essential steps of the assessment work, the hydraulic conductivities of the fractured rock masses should be reliably determined based on the limited measured data and geological information from the few boreholes. On the basis of site investigation data and monitored water flow and water pressure data during excavation, this paper presents an estimation method for hydraulic conductivities of the rock masses containing water bearing zones.INTRODUCTIONIn the development of underground rock caverns/tunnels, the uncertainty of hydro-geological conditions plays a critical role in terms of construction cost and construction safety. Excessive groundwater seepage has been identified as one of the key safety factors which always lead to vast loss, such as the Seikan Tunnel in Japan which encountered sudden water inflow and then catastrophic face collapsing, tunnel flood during excavation (Xu et al., 2013). As a key factor in the risk management associated with the groundwater leakage into rock cavern, the hydraulic conductivity determination is very important for cost estimation, reliable water control and construction management.The case presented in this paper is an underground project consisted of a cluster of rock caverns/tunnels for storage of hydrocarbon products. These caverns are located in heterogeneous sedimentary bedrock, at a depth of 130 m beneath a basin, and the crowns of caverns are located at about 100 m below the sea bottom. The caverns/tunnels are designed at two levels, the water curtain tunnels are at the upper level, and oil storage caverns are at the lower level, as shown in Figure 1. A number of horizontal and vertical water injection holes drilled from the upper water curtain gallery tunnel will establish continuous horizontal and vertical water curtains for providing a stable pressure distribution around the caverns, to keep oil/gas inside the lower storage caverns. As the hydrostatic pressure of groundwater around the storage caverns is higher than the pressure of stored oil and gas, the stored oil and gas will not leak out of the cavern (Lu, 2010; Xu et al., 2015). Groundwater pressure gauges are installed in the water curtain gallery tunnels, and water from the operational and access tunnels is injected continuously into the curtains to maintain the pressure. Some monitoring data are recorded at different construction stages. This paper proposes suitable methods to predict the hydraulic conductivity in rock mass and to determine the hydraulic conductivity in the water bearing zones."

Jan 1, 2015

By M. El Tokhi, H. Arman, B. M. Amin

"This paper aims to overview some mechanical and physical features of the gabbroic rocks. The study has two phases: filed study/in-situ measurements and laboratory work. During the field studies, rock block samples were collected from different locations of the study area to represent the different types of the gabbroic rocks. Either core or rock samples for various tests were prepared from rock samples taken to the laboratory. The unconfined compressive strength (UCS), indirect tensile strength (ITS), point load index (PLI), Schmidth hammer rebound value (SHV), slake durability index (SDI), sonic velocity (SV) and unit weight (UW) test were carried out either on the selected rock block samples or core samples.INTRODUCTIONThe geology of the United Arab Emirates (UAE) has been divided into three major rock units (Lippard et al., 1986); an autochthonous succession, allochthonous units composed mainly of Mesozoic rocks and include the Sumeini Group (concomittent slope sediments), Hawasina Complex (basinal sediments) and the Semail ophiolite nappe (massive slice of former oceanic crust), that were emplaced as a series of thrust nappe in the Late Cretaceous and Neo-autochthonous sequence of Maastrichtian and Lower Tertiary sediments.The Semail Ophiolite (600 km long and up to 150 km wide) is thought by some authors (Glennie et al., 1990) to have been generated along a subduction related back-arc spreading axis during the Cenomanian-Turonian and was obducted onto the Arabian continental margin during the Campanian. Others, however, consider it to represent a primitive arc-spreading center related to oblique subduction Lippard et al., 1986). The Ophiolitic rocks in the study area comprise mantle and crustal sequences. The mantle peridotite and crustal gabbros are the dominant rock types of the exposed Semail Ophiolite north of the Hatta zone. This paper is only concentrated on the gabbroic rocks."

Jan 1, 2015

By Jon Errey, Aleksandar Petrovic, Karl Haase

"Developing a gold deposit of this magnitude in the Amazonian jungle of Guyana posed many challenges. This paper describes not only the process & logistical challenges arising from the remote mine site location in a tropical environment with a local industry unaccustomed to recent large scale gold mining operations, but also the innovative technical solutions employed to address the unique ore body characteristics. The best examples of this approach were dealing with the initial high clay content saprolite ore from the development phase and primary mining pits whilst ensuring that the design also implemented the right method to deal with the future fresh rock in an environmentally sensitive habitat. In order to do this separate individual crushing flowsheets were generated, focusing on the specific material handling equipment that would be suitable to handle these various types of material and ensure high recoveries were maintained.INTRODUCTIONAurora gold mine is located in forested region of Guyana, 170 km west of capital Georgetown, and 130 km West North-West of Bartica, a settlement at the junction of the Essequibo and Cuyuni Rivers.The Aurora gold project (Aurora) is a 5,000 tonne per day open-pit/underground operation, which will produce a total of 3.29 million oz. gold – averaging 194,000 oz. per year – over an initial 17 year mine life. At the final investment decision in 2014 Aurora had a total resource of 6.54 million ounces in the measured and indicated categories (62.83 million tonnes at 3.24 g/t Au) as well as additional 1.82 million ounces in the inferred category (16.93 million tonnes at 3.34 g/t Au)."

Jan 1, 2016

By John Tribe

"This paper gives the organizational history of Luscar Ltd. and its various coal producing operations. Each 0/ the operations is then described individually. They include the Bienfait Mine, the Boundary Dam Mine, the Diplomat Mine, the Luscar Mine and the Coal Valley Mine. The company's plans/or expansion are also discussed. IntroductionLuscar Ltd. is an Edmonton-based energy company formed in 1967 through an amalgamation of two pioneer coal companies-Mountain Park Collieries and Luscar Coals Ltd. In 1912, Mountain Park Collieries initiated the development of an underground mine in the Coal Branch area of Alberta. This mine necessitated the establishment of a townsite and the provision of rail access. The second operation, Luscar Coals Ltd., was established in 1921 at Luscar, Alberta. This was also an underground operation and required the development of a rail spur and townsite. The product from both mines was used to fuel railway steam locomotives until the 1950's. The market demand for coal decreased as the use of the diesel locomotive increased, so that these operations were finally closed in 1954. Through the amalgamation of the two companies in 1967, however, Luscar Ltd. was formed to become an active participant in the revival of coal operations. Western Canadian Luscar Ltd. is involved in the exploration, development, production and marketing of coal, coal products, oil and gas. Luscar Ltd. is currently participating in five producing mines (Fig. I). The Diplomat Mine, approximately 125 miles southeast of Edmonton, was in production when it was acquired in 1949 by Luscar Coals Ltd. In 1966, the Bienfait Mine and char plant were added. The Luscar Mine, which is a 50/50 joint venture of Luscar Ltd. and the Consolidation Coal Company of Canada, and is operated by Cardinal River Coals Limited, started production in 1969 on the original Luscar Coals Ltd. mine site. The Boundary Dam Mine was opened in 1974. Both the Bienfait and Boundary Dam operations are located in the lignite coal fields of southeastern Saskatchewan. The most recent addition to the group is the Coal Valley Mine, 40 miles southwest of Edson, Alberta. It commenced commercial production in July, 1978 under the operation of Luscar Stereo (1977) Limited."

Jan 1, 1980

By Michael Arriagada, Ivan Arriagada

"As mines return to shafts to economically exploit deeper reserves, two methods mine owners use to minimize short term costs are: sinking shafts in phases and refurbishing old, existing shafts. While there may appear to be benefits to utilizing existing infrastructure, often this is not the case, resulting in missed deadlines and added costs. Similarly, if proper long term planning is not executed when sinking a shaft in phases, additional costs and downtime will be accrued. This paper will take an in depth look at both of these options with an eye towards optimizing costs, minimizing downtime, and facilitating construction. INTRODUCTION With the onset of mechanized mining and large capacity trucks, many mines turned away from shafts and began to use ramps to haul ore to surface. However, continual exploitation of mineral reserves located closer to surface, combined with the subsequent unearthing of additional resources at greater depths, forced mines to go deeper and deeper to extend the life and keep the operation running. In shallow mines, hauling ore by truck was an economical option. However, as mines get deeper, driving ramps takes additional time, and hauling over longer and longer distances becomes less economic, both in terms of cost and time. For this reason Mexico, in particular, has seen a jump in the number of shafts which have been put into production, as well as having a number of shafts in different stages of development and still more in the conceptual stages. Many of the shaft projects in Mexico are being designed in phases, with the hoist and equipment purchased capable of reaching the ultimate planned depth of the shaft, but with sinking operations stopping short at an intermediate depth. A loading pocket is then installed to start exploiting mineral at this depth sooner, with subsequent phases planned for a later date using either a rock pentice or bulkhead to separate the sinking operations from the active shaft above. Currently, we are directly involved in two such projects which are actively being deepened, as well as having seen various others already reach completion. If done properly with the long-term plan in mind, sinking in phases can be a very viable option, allowing for faster production while fully utilizing the equipment at various depths. However, there are many issues which can arise when sinking a shaft in phases that if not properly examined and planned for from the outset, have the potential to eliminate the gains hoped for when it was decided to sink in this manner."

Jan 1, 2019

By C. H. Bucknam

Net carbonate value (NCV) characterization methods for acid generation potential measurement originated from studies on the Carlin Trend during the 1990's and have been subsequently standardized through cooperation of the Acid Drainage Technology Initiative Metal Mining Sector and the American Society of Testing and Materials International. The paper describes the evolution and standardization of the NCV methods, the importance of mineralogy in interpreting the results and application of the methods to implementation of the Global Acid Rock Drainage (GARD) Guide.

Jan 1, 2011

By J. Font

The RAF or copper fire refining process at the Caletones smelter of CodelcoChile consists of several pyrorefining stages that successively lowers the levels of S, Fe, Pb, As, Sb, Te, Se and to some extent 0 in the copper melt, allowing the production of high quality fire-refined copper of 99.93 % purity (RAF copper). This chemical feature of the RAF copper is only achieved by quite long processing times, and a considerable consumption of fluxes and fuels in the RAF vessels. The main goal of this study was to improve the RAF process performance by thermodynamic considerations and industrial scale tests, i.e., an in situ approach for the process as featured by intensive sampling, characterization and subsequent modifications. Thus, both theoretical and industrial data were derived, and based on kinetic and thermodynamic evaluations, a higher operational standard was achieved for the RAF process. These new operational practices allowed enhancing the overall economic of the RAF process, by reducing the time and operational costs, and consequently increasing the availability of the vessels.

Jan 1, 2007

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By Donald F. MacDonald

METAL PRICES RISE WITHIN the past nine months, the mining industry of the world has been revivified by a spectacular price advance for the metals. ln fact, practically all geological raw materials have been marked up during this period. Reviving industry started the price rise, but the armaments race among the nations has intensified it. These factors, coupled with our decided building shortage, which must be made up, will probably maintain metal prices at decidedly favourable levels over the next two or three years, or longer. OUR MINERAL CIVILIZATION It is interesting to recall that in the past hundred years, while the white population of the world increased some three ta three and a half fold, the consumption of minerals increased seventy-five fold. In other words, ours is a mineral civilization. If we disregard short slumps, which we will occasionally experience, it seems certain that the bread upward trend in mineral consumption will be maintained for many decades into the future. Nations without reasonably abundant and diverse mineral deposits will eventually become nations without much power. Canada is blessed with a splendid store of minerals. Its mineral industry is now facing an exceptionally rosy future. What of the mineral industry of Nova Scotia? GEOLOGICAL RESEARCH ALLOWED TO LAG RN NOVA SCONA Many years ago, when geological science was in? its infancy, much geological study was carried on in Nova Scotia. In 1827, Francis Alger began work on the iron ores in the Bay of Fundy region. In 1886, E. R. Faribault began his series of remarkable papers on Nova Scotia geology. Between these dates, many others published papers on the geology of the Province. The most outstanding of this early group of geologists was Sir William Dawson, whose published works on Nova Scotian geology extended over the period from 1845 to 1891.

Jan 1, 1937

By O. C. Rojas, J. Sanhueza, J. C. Vargas

Empresa Nacional de Minería (ENAMI) is dedicated to the promotion of small and mid scale Chilean mining industry. Paipote, ENAMI Copper Smelter, processes a variety of mineral products as the result of this promotion. The mineral products characterize a wide variation of copper, iron, sulfur and precious metals content as well as the significant dispersion in the content of impurities, such as arsenic, antimony and bismuth. The Smelter Modernization Program, initiated in1997, introduced a series of technological and operational changes. The development of operational planning and control strategies was necessary to optimize the blending of a wide variety of concentrates and the control of metallurgical processes in order to ensure the stable operation, fulfillment of environmental regulations and the quality of produced copper anodes. A permanent optimization process carried out in the last decade led to the permanent increase of the smelting capacity and the production of anodes and sulfuric acid. Additionally, introduced improvements affected the smelter efficiency and metallurgical recovery, demonstrating the possibilities of the optimization of a small smelting facility reflected in good metallurgical and economic results. This paper presents the smelter evolution, introduced technological and process control changes as well as incorporated new reactors and equipment as a continuous process of optimization.

Jan 1, 2007

By Steve T. Laflin

Since the beginning of the nuclear era, there has never been a commercial solution for the large quantities of depleted uranium hexafluoride generated from uranium enrichment. In the United States alone, there is already in excess of 1.6 billion pounds of DUF6 currently stored. INIS is constructing a commercial uranium processing and fluorine extraction facility. The INIS facility will convert depleted uranium hexafluoride and use it as feed material for the patented Fluorine Extraction Process to produce high purity fluoride gases and anhydrous hydrofluoric acid. The project will provide an environmentally friendly and commercially viable solution for DUF6 tails management.

Aug 1, 2010

By Vladislava A. Ignatkina, Victor D. Samyguin

"Within the limits of two-phase approach, considering mass transfer with pulp and air streams was shown that each bubble appears to be an elementary carrier, transporting particles from the collection zone into the froth. The kinetics of flotation was described by the exponential equation in which first order flotation speed constant has to be replaced with two-phased coefficient of a mass transfer. Criteria of selectivity of two ore fractions separation, based on determination of optimum time at which maximum difference between extractions and components content in separated fractions were offered. An interrelation between optimum time of pulp residence in a flowing chamber of a flotation machine, time of bubbles mineralization and an optimum airflow has been ascertained. Cumulative criterion of mass transfer efficiency of flotation process has been ascertained to be a form of the spectrum and its position on axis of three-phase coefficient of a mass transfer.INTRODUCTIONRegularities of a mass transfer of three bearing streams: pulp stream, air stream and froth stream underlie theory of mineral complexes flotation (Samygin, Filippov, & Shekhirev, 2003)However, only description of mass transfer in pulp stream by means of kinetic equations that were simple and convenient for practical use, has gained a full distribution (Tykhonov, 2009;Rubinstein&Filippov, 1980; Saleh, 2010).Within the limits of a single-phase approach, the role of gas stream in increase of speed and selectivity of flotation, was associated with an improvement of hydrodynamic mode. An influence of particles and bubbles sizes (Rubinstein&Filippov, 1980; Rubinstein&Samygin, 1998, Samygin et al., 2003; Dai, Fornasiero,& Ralston, 2000), of pulpflow and airflow (Finch& Dobby, 1990) and turbulent energy intensity (Shubert, 1979; Massinaei, 2007) on the flotation process has been studied. It was stated that flotation selectivity is increasing by means of gradual airflow increase from first to final cameras of the impeller flotation machine (Aslan&Boz,2010; Finch, 2011) and by means of using a multizone flotation machine (Samyguin, Filippov, Matinin, Lekhatinov, &Tertyshnikov, 2013)."

Jan 1, 2016

By J. Janeson

Wall control at the Pipe Open Pit is of primary importance in ensuring the long-term stability of the operation, while keeping costs to a minimum. Blasting techniques have been adapted to the variations in competence and structure of the wall rocks. A portion of the perimeter wall is being developed in incompetent peridotite . A recent change in pit slope design provides a wide safety berm on alternate benches. A support program which consists of pinning the crests of wide berms with vertical reinforced concrete dowels and horizontal bolting of walls shows evidence of increasing the stability of the pit walls. This paper describes the blasting and support techniques which are contributing to successful wall control in the Pipe operation.

Jan 1, 1979

By Y. Wong

The quality and quantity of secondary deposits, which include tailings streams and tailings dams, are increasing around the globe. The tailings are already mined, available and liberated to such an extent that the recovery of a valuable product is highly economical in terms of CAPEX & OPEX. The most widely used process for the recovery of these valuable ultra-fine haematite iron particles is the Wet High Intensity Magnetic Separation technique, originally developed by Dr. Jones over 55 years ago. Many of the original machines are still working today. The aim of this paper is to demonstrate the capabilities in terms of grade and yield of using sophisticated magnetic separation modules. All results and figures are obtained from test works, design- and engineering works. Two types of tailings have been identified for processing. Firstly, tailings that have already been deposited in a Tailings Storage Facility, and secondly, live tailings streams from an existing wet iron ore beneficiation plant. In both cases, the technical and practical results are shown along with relevant flow sheets and plant layouts. Finally, this paper highlights the total predicted power- and water consumptions, capital requirements and projected operating expenses. The results show that the operating costs are significantly lower than the mining and processing operations which are required for an equivalent amount of iron ore. The recovery % of iron depends on various factors but is within the 30–50% range, at an equivalent grade to the mainstream product. Another significant benefit is that the magnetic separation process is water positive, meaning that water is released rather than added in the process. The processing of secondary deposits will therefore result in an overall reduction in operating costs, an increase in product yield from a plant, extend the mine life and offer environmental benefits by reducing the tailings footprint and water usage.

Jan 1, 2016

By Patrice Nadeau, Yuejun Zhang, Dan Chen, Liming Huang, Claude Gagnon

"The traditional Denver flotation cell is generally suitable to process material ranging approximately from 5 µm to 300 µm. For floating over 300 µm material, its efficiency is significantly getting lower mainly due to the difficulty to suspend coarse particles uniformly, which decreases the chances of particles to attach to bubbles and increases the chances of detachment.RTFT (Rio Tinto Fer et Titane) owns one of the world’s largest hemo-ilmenite deposits. Considering the whole processing technology, the ore is only crushed to -1180 µm. The crushed ore contains about 0.32% S and most of the sulfur is removed by rotary kilns in the ore preparation plant. In order to achieve a similar S reduction, without emitting SO2 into the air, an alternative technology by flotation was pursued.Laboratory and pilot scale-up tests showed that traditional Denver flotation cell could perfectly remove the sulfur from the material sizing 0-300 µm. For the coarser particle sizes, two different models of equipment were tested to improve flotation efficiency: HF (HydroFloat Separator) from Eriez and CLF from BGRIMM (Beijing General Research Institute of Mining and Metallurgy), China. The D6” HF, which is a device that combines flotation and gravity separation, demonstrated its ability to recover those very coarse particles. As compared to the Denver flotation cell, the modified 25 L CLF coarse particle flotation cell achieved better results at higher pulp solids percentage and with a shorter flowsheet."

Jan 1, 2016

A direct comparison has been undertaken between laboratory wind tunnel experimentation and computational fluid dynamics simulation of a 3D manufactured analogue for a body of fractured broken rock, created with CAD/CAM techniques. Detailed descriptions of the ?design? of the analogue (using a discrete element analysis multi-body simulator), its manufacture (using computer aided design and 3D printing technology) and the laboratory experimentation (inserting the physical analogue into a laboratory scale wind tunnel) are presented. The agreement of the results of direct experimental observations on the manufactured analogue with the values from CFD simulations of those experiments justifies the utilization of a CFD environment for the practical investigation of geometric factors controlling air flow and heat exchange in complex assemblages of broken rock blocks. The ultimate goal is described, that of developing functional relations between bulk properties of such assemblages (such as their porosity and bulk density) and the low-level geometric factors that dictate the air flow behaviour, such as the equivalent perimeter length of the cross-sectional area available for flow, or average flow path tortuosity. A practical application area of the work in the mining context is also described; equivalent continuum air flow and heat transfer constitutive models developed on the CFD tool from such functional relations are useful in characterization of seasonal heat storage in large scale bodies (approximately 1 km3) of broken rock.

Aug 1, 2013

This paper describes results of an investigation of fracture during tube expansion of 5052 and 5754 aluminum seam-welded tubes to optimize the forming of aluminum tubes during hydroforming. The tubes were produced in laboratory by press forming of tubular blanks and pilot-scale high frequency induction welding. The effect of property mismatch between the weld and base metal has been investigated. The material work-hardening was obtained by roll forming of sheet blanks in the 0-temper and H32 temper condition. The results showed that a significant work-hardening can be present in aluminum tube without causing weld fracture during tube expansion. The work-hardening increases the yield-strength mismatch between base metal and weld. Annealing reduces the hardness of base metal leading to more uniform deformation during tube expansion. As a result the occurrence of weld fracture is reduced. The study showed significant deformation of the welds during tube expansion. Weld thinning can be as large as parent-material thinning before fracture. To avoid fracture at the weld joint, good formability and high yield strength of the weld is needed. FEM simulation showed that minimizing the width of the weld joint can reduce thinning of the weld.

Jan 1, 2004

By S. Xu

Magnesium alloy AM50 is of interest to automotive cradle application because of it excellent castability and good ductility. In this work, microstructure and mechanical properties of both low pressure die cast (LPDC) and high pressure die cast (HPDC) AM50 test bars are characterized. Microstructure was examined using optical microscope, scanning electron microscope (SEM) and transmission electron microscope (TEM). Phase identifications were performed using energy dispersive x-ray spectrometer (EDS) and TEM diffraction. It has been found that LPDC produces much coarser microstructure than HPDC. At the same time, the HPDC samples are more heterogeneous in microstructure and composition close to grain boundaries. Particles with various dimensions and morphologies of two different intermetallic phases, Mg17A112 and A18Mn5, were found in all the samples. Mechanical tests were performed under conditions similar to those related to an engine cradle application. LPDC samples show lower strength but better creep resistance than HPDC mainly due to the difference in grain sizes and grain boundary microstructure between LPDC and HPDC. Creep curves are well described by the empirical Andrade equation. Tensile-compressive yield and creep asymmetries were found in AM50, i.e. better deformation resistance in tension than in compression. The average yield asymmetry ratio for all the samples is 0.87. Microstructural examinations on the samples tested in tension, compression and creep showed that the deformation mechanisms in AM50 were slip plus twining at temperatures up to 125°C. The examinations indicate the important role of twining in the asymmetry phenomenon. The creep results indicate that dynamic precipitation of the Mg17A112 phase during testing is not the mechanism directly responsible for the creep asymmetry in AM50.

Jan 1, 2004

By X. -G. Chen, J. Qin, K. Liu, D. Racine

"Understanding the thermo-mechanical fatigue (TMF) behavior of materials plays a significant role in the safety design of critical components used in aerospace and automotive industries, such as engine blocks and cylinder heads, which undergo the cyclic change of temperature and stress. However, the cyclic changes of temperature, stress and strain make it difficult using the traditional testing methods to accurately simulate the TMF process. In the present work, the Gleeble® 3800 system was successfully applied to develop a reliable procedure to measure the TMF behavior of aluminum alloys. The modified setup together with the new designed program allows the Gleeble system to precisely simulate the cyclic profiles of temperature and mechanical strain. The novel procedure includes the calibration and verification of the TMF setup to ensure the test validity with Young’s modulus measurement, multi-cycle measurement of the thermal strain and zero stress adjustment followed by online monitoring the TMF cycles. The results of the TMF testing of an AA6061 alloy under cyclic temperatures (60–300°C) and various strain amplitudes (0.2–0.6%) were demonstrated. Its TMF behavior was characterized by the typical hysteresis loops and cyclic stress-strain response.INTRODUCTION The thermo-mechanical fatigue (TMF) behaviour becomes increasing important to evaluate the elevated-temperature properties of materials used as the critical components in automotive and aerospace industries, such as the gas turbines (Hu, Shi & Yang, 2016; Moverare, 2007; Segersäll et al., 2015) and engine blocks (Grieb, Christ & Plege, 2010; Javidani & Larouche, 2014). During the cycles of start-up and shutdown of the engines, these components undergo a complex change of loading. Meanwhile, a dramatic temperature gradient exists on the components due to the cooling system. Therefore, the cyclic changes of load and temperature can give rise to the TMF and may limit the use life of such components (Hu, Shi & Yang, 2016; Javidani & Larouche, 2014; Moverare, 2007). Hence, performing the TMF tests to precisely simulate the cyclic changes of load and temperature to understand the TMF behaviours of materials is playing a significant role in the safety design of these components. For TMF tests, two principal types of cycles are generally employed, including the in-phase (IP) cycle where the load and temperature are at the same phase (i.e. maximum load at highest temperature) and out-of-phase (OP) cycle where the maximum load is applied at minimum temperature (Kliemt, 2012; Miller, 2014). The most significant damage mechanisms in engine components are reported to be OP TMF cycles (Javidani & Larouche, 2014; Kliemt, 2012)."

Jan 1, 2018

By P. D. Barrette

This paper deals with the flow of granular materials in bins. A hybrid Lagrangian-Eulerian numerical model is introduced. The model is based on Particle-In-Cell (PIC) advection, and continuum equations describing a Mohr-Coulomb criterion. Experiments were conducted to test and verify the performance of the numerical model. Tests were done using three types of particles. Measurements of material properties and flow rates were carried out. Video records were also obtained and used to examine flow patterns. The results indicate that the numerical simulations produce deformation patterns and flow rates which are in good agreement with the experimental observations.

May 1, 2007