Search Documents

By R. F. Robertson

"Adsorption isotherms of hexyl mercaptan vapour on synthetic sphalerite, zinc sulphide and zinc oxide were de-termined with a gravimetric McBain-Baker micro balance incorporated in the B.E.T. apparatus. Isotherms are given for hexyl mercaptan on synthetic sphalerite at 25°C, 0.5°C and 50°C; on zinc sulphide at 25°C and 1.5°C; and on zinc oxide at 25°C. All these isotherms are sigmoidal, with a definite change in slope at or close to the mono-layer. The amount of mercaptan adsorbed below the monolayer increases almost linearly with relative pressure to P/P0 = 0.8.Above this value, the amount adsorbed increases very rapidly with relative pressure. Hysteresis loops appear in the isotherms for all adsorption-desorption cycles. These loops are completely reversible. It is not possible to desorb the mercaptan monolayer from any of the adsorbents, even at elevated temperatures."

Jan 1, 1966

By Y. Duna

The reliability of mine ventilation systems is critical to normal and safe production in a mine and includes reliability of the following parts: ventilation system branch (or passage), ventilation structures, ventilation network, and the fan. Among these, the reliability of a ventilation branch may be considered the foundation of the whole ventilation system. The branch ventilation flow includes four parameters: air volume; toxic and hazardous gas concentrations; temperature, and dust concentration. The calculation model for the reliability of a branch was established based on the analysis of normal distribution of flows in any one branch. Then, the efficiency of the ventilation structures and fire risk compromising the reliability of branch was studied. The results obtained were as follows: if the air volume, toxic and hazardous gas concentrations, temperature and coal dust concentrations of the branch are within reasonable limits, set at any stable state and at the same time, then this branch is reliable.

Aug 1, 2013

By R. P. Viljoen, A. D. Scheglov, A. L. Sokolov

"Abstract -The distribution of mineralized provinces is analyzed on the basis of their genetic link with specific blocks of the earth's crust including ancient platforms, mobile belts and zones of tectonic­ magmatic activation. Mobile and fold belts surround the Siberian platform in Russia and the Kaapvaal craton in South Africa, with decreasing age zoning away from ancient platform margins. The main differences in the geological development of the two cratonic areas are: (1) the long period before the final stabilization of the Siberian platform (3600 Ma to 1600 Ma) and the comparatively short period of time for the stabilization of the Kaapvaal craton (3600 Ma to 3050 Ma) and (2) the intensive multiple activation of the marginal zones of the Siberian platform and the tectonically­ controlled, magmatic sedimentary, intracratonic activity, typical of the Kaapvaal craton. Mineralization of the Siberian platform is largely characterized by marginal reactivation zones of differing ages although mineralized intracratonic Cu-bearing basins of Proterozoic age are also known. Mineralization of the Kaapvaal craton is mainly related to the formation of the intracratonic basins i.e., Witwatersrand (Au, U) and Transvaal (Au). The latter is characterized by multi-age volcanic-intrusive activity including the emplacement of Bushveld Complex (Cu, Ni, Pt, Cr, Au, V). The Siberian platform is characterized by the prolonged development of inherited mineralization from Archean until the late Mesozoic. The main period of mineralization in the Kaapvaal craton is restricted to the middle Proterozoic.The Baykal-Patomskaya and Namaqua-Natal mobile zones occupy similar positions adjacent to the Siberian and Kaapvaal cratons, respectively, and demonstrate similar modes of metallogenic development: i.e., the early formation of exhalative Pb-Zn-Cu deposits during the early stage and magmatic Cu deposits during the late stage. The more remote mobile belt near the Siberian plat­ form, the Trans-Baykal, is characterized by intensive multi-age mineralization (Wo, Mo, Sn, fluorite), related to a period of tectonic-magmatic activation. The Saldania Belt occupies a similar position near the Kaapvaal craton but is known for its poor Au, and Cu rnineralization. lt does, however, have some similarities with Trans-Baykal Belt in regard to Mo-W bearing granitoids.The phenomenon of interference of geosynclinal, orogenic, platform, and tectono-magmatic activation regimes is known for the Russian section of the Pacific Ocean Volcanic Belt."

Jan 1, 1994

By P. D. Hodgson, G. L. Kelly, H. Beladi

"The formation of ultrafine ferrite by strain induced transformation is assessed using rolling and hot torsion experiments. These experiments are used to examine the impact of thermomechanical processing conditions and steel chemistry on strain induced austenite to ferrite transformation and the formation of ultrafine ferrite. The critical strain for dynamic strain induced transformation increased with increasing carbon equivalence, deformation temperature and austenite grain size. The deformation structure in the austenite grains changes with the thermomechanical processing conditions.Drawing on these results and the current literature, the important factors for the production of ultrafine ferrite are described and a mechanism proposed."

Jan 1, 2004

By J. B. Evans

"THE OPPORTUNITY to participate in a CIM seminarconcerning the direction of mining engineer trainingis perhaps fortuitous as it comes at a time when theengineering schools which have invited inspection byCanadian Accreditation Board of the Canadian Councilof Professional Engineers are examining theirrespective curricula.Currently there exists considerable soul-searching in various engineering schools across Canada where questions such as the following are being posed.- Have we achieved the correct balance between subjects related to technical methodology and subjects devoted to conceptual planning and design?- Should we include ""applied humanities"" in our program? (Whatever ""applied humanities"" might mean!)- Should courses covering pollution control, ecology, economics, technical writing, professional conduct and ethics be offered as compulsory subjects, as electives, or not at all?- Is it a better scheme to have students complete an Arts or Science degree before entering engineering?- Do we place too much emphasis on pure mathematics and sciences with the result that insufficient time is available for instruction in the engineering applications of these subjects?- Should English expression and/ or literature be included in the engineering programs and, if so, should these subjects be presented by the English department or by English lecturers captive to the engineering school? - Is the present program directed primarily at research activities rather than preparing engineers for their future roles in industry? - Should we teach our own versions of mathematics and physics? - Do we have sufficient engineers on the faculty strength or are we overloaded with Ph.D.'s from the pure sciences? - How flexible should the program be, what should the compulsory vs elective course content be, and what freedom of choice, if any, should be given with respect to elective courses? - To what extent should students contribute to faculty decisions?- How far should we pursue computer science subjects and do we need to make our students proficient in computer programming? - How far should operations research and mathematical models be carried in the undergraduate program when the students have limited experience in the real engineering world? - Realizing that an engineer never completes his education, should the undergraduate program cover ""bare bones"" engineering and should instruction in particular disciplines be left to graduate schools and / or industry?"

Jan 1, 1972

By P. Blonde

Recent analysis has suggested that a balanced recovery profile can improve flotation bank performance. Test work was conducted to test the balanced profile concept at the Penhorwood talc mine near Timmins, Ontario, Canada. Plant trials were devised to determine how to control the recovery profile and the resultant impact on grade and recovery in a rougher bank of four cells. Accompanying gas dispersion measurements revealed a maintenance issue with one cell that was corrected. By manipulating air and frother addition it was possible to bring the bank closer to a balanced recovery profile and the down-the-bank grade/recovery improved. Plant production showed an increased talc grade at similar yield with the balanced profile. The results provide justification for a long term plant trial.

Aug 1, 2013

By R. W. Thompkins

In order to evaluate the impact of air quality control on mine design, a few examples are given of cases in wh.ich ventilation has affected the economics of the total design problem. Principles for the drainage of gas contaminants are shown, and the contamination control problems created by differential pressures in complicated booster fan installations are discussed. The paper also deals with the use of advanced mathematics for solving some of the ventilation problems likely to be encountered.

Jan 1, 1967

By Yin Wang, Lin Li, Zhongwei Bi, Like Wei, Wen Li, Shaogang Li, Bin Zhang, Hongjie Li

Presently,Many long-wall fully-mechanized faces in shallow depth coal seams are below room and pillar goaf in Shendong mining area. When the working face is advanced out of concentrated coal pillar in upper room and pillar goaf, strong strata behaviors often cause support crushing accident. Aiming at a support crushing accident which happened in Shigetai coal mine of Shenhua group in Shendong mining area, this paper analyses the stress transfer process while mining out of concentrated coal pillar by numerical simulation software FLAC3D. According to the feature, simplifying the roof of upper room and pillar goaf as supporting-beam structure explains mechanism of large area collapse in room and pillar goaf roof. Based on the feature of supporting-beam structure, deep-hole blasting concentrated coal pillar technology is proposed to control the strong strata behaviors in Shigetai coal mine. The blasting control effect is confirmed through characteristics of strata behaviors, growth circumstance of ground crack and multi-point extensometer monitoring results. By using control technology, Shigetai coal mine has been successfully avoided support crushing accident.

Jan 1, 2015

By M. Silver, R. H. McCorkell

The effects of covering materials on radon emanations from uranium mine mill tailings were investigated. Granular materials with air in the spaces allow radon to pass freely. Moist covers of compost or soil decrease radon emanation from tailings. Water-saturated covers were more effective, and freezing the tailings with these covers further decreased radon escape. Water itself is a poor radon barrier probably due to circulation. Plants had no effect on radon emanation through soil. Although radon diffusion through water-saturated powders appears to be very slow and inefficient, about 25% of the radon escaping from the grains in water-saturated tailings diffuse to the surface and emanate when no cover is present. The radon escaping from tailings through covers of water-saturated compost or soil is no more than could be accounted for by radon produced in the covers themselves.

Jan 1, 1987

By C. M. Campbell

IN 1902, a famous Canadian geologist made the following statement : ?'From what we know row of the iron-ore fields of the Province, we may feel that Ontario is assured of a great future as an iron-ore producing country. Judging from the extent of the territory over which the newly discovered ranges have been found, Ontario should in the not far distant future take her place as one of the chief iron producers in the world". In 1905, an official of the Department of Mines said: "In ten years Canada will have b:ecome a great metallurgical country. You will see an iron industry in this Dominion larger than in any country in the world. Canada will yet furnish the world with its iron supply. It will be the same with iron as with wheat. A decade from now Canada will outstrip all other countries in wheat growing. The production of iron at a cheaper rate than it can be made elsewhere will cause Canada to take a similar position as far as iron is concerned". In 1924, a former President of the Institute, in arguing his claim for inconceivable mineral wealth in this country, stated as a "certainty" that iron-ore deposits on the scale of the ones in Minnesota would be found "again and again" in the Canadian Precambrian. In 1930, a Minister of Mines announced that "The country surrounding Churchill holds large deposits of valuable iron and coal", and he stated that, at that place, 'We will have an industry in iron that will compare with Pittsburgh". These statements are definite promises, just as definite and important as the statement "I promise to pay" on a note, and they are not fulfilled by casually stating, as is the habit, that someday we will work our low-grade iron ores. Nor are they fulfilled by stating, as is often done, "Oh, So-and-So did not mean that ' . Due to their importance and to the prominent positions held by the men who made these statements, they were widely circulated throughout Canada. They were taken at their face value, and on the strength of them and many more of the same kind in regard to our other resources we have planned and built, at huge expense, provinces, governments, civil services, railways, and other equipment. The reserves that were to justify these expenditures have not appeared. There has not been a ton of iron ore mined in Canada for many years, and important commercial reserves are unknown. We have built the mill, but adequate ore is lacking.

Jan 1, 1937

By Karl J. C. Harries

"14.1. INTRODUCTION1The boilerplate of an agreement is not a single provision, but a series of provisions that are expected in “every agreement”. They are sometimes also referred to as the “lawyer’s provisions”. Many businessmen consider the boilerplate to be superfluous and, to some extent, window-dressing by the lawyers – even legalese. They will often offer advice to the effect that it can “pretty well be ignored”. Such advice could not be more wrong.Most boilerplate provisions are essential parts of every agreement. Some may be part of a “standard package” and may have little relevance to the agreement at hand, but these are the exception rather than the rule. The exceptions should not be treated as justification for giving all these provisions short shrift. The boilerplate should receive the same review, consideration, and negotiation as the provisions that set forth the business deal. It is often these provisions that make the deal work or that are turned to at the time of disputes. If they are inadequate, as they sometimes are (unfortunately, some draftsmen are also loath to review or update their standard boilerplate provisions or to tailor them to the deal at hand), they can create problems, rather than offer solutions. Such problems can be costly and time-consuming for the parties to address. Inadequate or incomplete provisions may ultimately be one of the reasons for the parties to turn to the courts to settle their differences. On the other hand, good boilerplate provisions can help keep them out of the courts.One of the principal objectives of an agreement should be to provide procedures, or mechanics, for implementing agreed principles and for the parties to follow to settle their differences, real or perceived, without going to the expense and disruption of a lawsuit. An agreement should aim to keep the parties away from the courts, not serve as a springboard to the courts. It must nevertheless be acknowledged that, if there is a major falling-out among the parties to an agreement, the chances are that, however carefully the provisions of that agreement have been negotiated and drafted, the parties will end up before the courts or some other adjudicating body."

Jan 1, 2003

The effect of superficial gas rate distribution (Jg profile) on down-the-bank metallurgical response was tested in the rougher-scavenger bank (eight 10-m3 tank cells, 4 roughers and 4 scavengers) at Highland Valley Copper Mine's Cu/Mo separation circuit. Three Jg profiles were tested: (a) as found (i.e., typical practice), (b) increasing decreasing (i.e., increasing from cell 1 to 4 and decreasing from cell 5 to 8), and (c) decreasing-increasing (i.e., decreasing from cell 1 to 4 and increasing from cell 5 to 8). The Jg profile approach proved to be of considerable value. Profile (b) gave the best metallurgical results, i.e., the highest down-the-bank grade/recovery (increase in grade at constant recovery was approx. 3-4% compared to the as found case) and the most efficient Cu/Mo separation (cumulative Cu recovery was reduced by almost half - approx. from 20% to 12%, at 99% Mo recovery). The success of the evaluation prompted the implementation of profile (b). Detailed gas dispersion characterization tests (Jg and Db (bubble size)) showed significant discrepancies between the Jg measured directly (using the McGill University sensor) and the Jg calculated from field instrument readings (volumetric gas flowmeter) and machine dimensions (cell cross-sectional area). Tests were designed to reveal the source of disagreement. It was observed that a significant number of bubbles were not able to float (i.e., they were entrained with the tailings), the evidence appearing to be a significant number of very small bubbles (approx. 200-300 µm) which did not have sufficient buoyancy to rise. Consequently, rather than relying on the field instrument, the evaluation depended on the McGill University Jg sensor, which collects bubbles in a tube near the pulp-froth interface, thus providing significance to the data as the measurements were obtained from bubbles that almost certainly floated.

Jan 1, 2007

By R. A. Nemchek

Over the years, concentrator plant design has evolved from a large number of small grinding mills to a small number of large mills. In many cases, all of the tonnage runs through a single mill (typically a large SAG mill), so that the plant?s performance hinges on the productivity of this one machine. Industry specifications attempt to address the critical nature of today?s grinding mills in a manner that is often overly complex, neglects economics, and is not clearly focused on the end user?s goals. This paper surveys current industry practices, and proposes an improved approach to standards writing recognizing that product design, procurement, manufacturing, and quality are all inter-related in contributing to a project?s success. The lessons learned here can be extended to specifications for all types of machinery.

Jan 1, 2012

By L. M. Amaratunga, G. G. Hein, D. N. Yaschyshyn

Fine tailings produced in the milling process have traditionally been disposed of in tailings ponds. Attempts have been made to use these fine tailings in backfill, however, to date the majority of backfill operations have utilized only a small percentage of fines. The remaining fines are, therefore, being sent to tailings ponds creating a waste disposal and environmental problem. This disposal practice is even more acute in the gold milling industry where fine grinding, required for value liberation, results in the production of large quantities of fine tailings, of which a large percentage cannot be used in backfill. Through Cold-Bond Tailings Agglomeration (CBTA), these fine tailings can be agglomerated into pellets which can then be used as a coarse aggregate in back-fill. This paper presents the results of using these pellets to create an Agglomerated Tailings Paste Fill (ATPF) made entirely of fine gold mill tailings and cementing binders. Through this process, supplementary imported aggregates such as sand, gravel, rock-chips are not required while still maintaining adequate back fill strength. By using this CBTA technology, fine tailings are diverted from tailings ponds and becomes utilized as a value added resource in the form of aggregates for use in paste fill.

Jan 1, 1997

By Wallace R. Horn

"MR. CHAIRMAN AND GENTLEMEN :I begin this talk by making a couple of comments which are of the nature of disclaimers.Firstly, and as the Chairman has otherwise indicated, I was neither ""born into"" nor have I spent more than a few years of my professional life in the mining industry. I mention this because many might, and perhaps rightly, consider that an added qualification in presenting a report of what the industry has accomplished. Indeed, I am not here to blindly defend all of its actions and inactions in respect to environmental control over the years. Nor am I here to seek absolution of the industry's past transgressions - if indeed that is the word. Mistakes might be a better one. I concluded some time ago that the effects of those mistakes are too difficult to assess against the sea of errors of our total society. I should mention too that I am not an environmental engineer or specialist - only a portion of my interest is involved with this field. Perhaps this permits a perspective which allows a more accurate and objective view.One further comment here. My job today, as I understand it, is to generally report upon the nature and extent of the response of the metals mining industry to control of the environment. In the case of an industry operating at more than a hundred locations and for various reasons at various stages of progress, it is not an easy job. On the other hand, I wanted to avoid the use of generalities because, especially within the context of environmental or ecological opinion and of the practice of condemnation of industrial segments, I think we've had about enough of generalities until we know far more than we do.Finally, I am quite aware that a statement of future plans to achieve environmental control does not impress or satisfy as many people as it may have done some years ago. Public opinion demands to know what is currently underway, today."

Jan 1, 1972

By R. G. K. Morrison

As mines grow deeper, the problem of ground control becomes one of increasing importance. The literature on the subject has grown extensively in the past few years, but is still far from conclusive. Detailed and precise observations are on record covering most phases of the problem, and control measures have progressed to the point where, in a large measure, they are effective. The success of methods to date must be attributed to the efforts which have been exerted to reduce convergence of stope walls and to the realization that a regular progression of stope faces approaching longwall has a beneficial effect. This paper attempts to explain the relationship between these two factors and the general problem of ground control. The problem at present lacks the co-ordination of the practical with the scientific outlook, but fortunately as time goes on there are indications that our scientific friends are becoming more interested and more familiar with the practical issues involved. Opinions vary widely regarding the mechanism of the problem and there are several schools of thought, two only of which will be discussed. One associates the incidence of rock-bursts with the stresses built up by a sagging hanging-wall, while the other takes the view that stresses primarily responsible for the sagging hanging-wall are also the cause of rock-bursts. The first group starts its reasoning from the convergence of the walls, probably the most conspicuous feature of deep mining, and works back to the conclusion that rock-bursts are in sorne way due to the breaking up of the sagging layers. The second group begins with the stress zone apparent around excavations at depth and follows mathematical conceptions based on certain assumptions which, in the absolute sense, are known to be inaccurate, but which are justified by the similarity between the conclusions reached and the results obtained in practice. This reasoning is followed to the point where rock-bursts result from the failure, under stress, of rock in situ, quite independent of wall convergence.

Jan 1, 1939

By Ian E. Efford

The paper gives an assessment of Canada's energy supply-and-demand position, the current situation and projections into the future, as well as a review of some alternative energy futures for Canada. The main elements of Canada's energy strategy for the period 1977-1990, with particular reference to the role of energy conservation, are discussed, leading in to the development of the national energy conservation program.

Jan 1, 1977

By V. L. Eardley-Wilmot

Diatomite as prepared for the market is a fluffy, white powder, remarkably light in weight-it weighs only 10 to 15 pounds per cubic foot, or one-tenth as much as sand. Being extremely porous and inert, it is in large and increasing demand for insulation and filtration purposes, as general filler, and for many other uses. Structure Structurally, diatomite is quite different from any other known commercial material. It is composed of myriads of microscopically small, siliceous shells of diatoms which belong to a group of flowerless aquatic plants called algae. When these plants die, the siliceous remains sink to the bottom of the water and form beds of diatomite. Over 8,000 species of diatoms are known, named, and tabulated. The intricate scroll-work and patterns on many of these are one of the marvels of nature, and yet so small are they that from 40 to 70 million separate diatoms may be contained in one cubic inch of material. However, the size and shape of these diatoms, which vary greatly (compare Figures 5 and 6), have an important bearing on the commercial use of the diatomite. The diatoms in the majority of the known deposits are so typical of that deposit that, after a micro-examination, an expert can usually tell not only from what part of the world, but also from what particular deposit, the sample has come.

Jan 1, 1931

By C. Morlot, C. Auvray, E. Fourreau, J. Talandier

"During the excavation of underground galleries in a rock mass, reorganisation of the stress field around the site results in damage to the surrounding material. In the framework of research undertaken at the ANDRA underground laboratory in France, galleries have been excavated in a Callovo-Oxfordian argillite formation. The damage has manifest as a number of fracture systems in the adjacent rock. Observations have shown that fractures generated during excavation and storage exploitation are able to self-seal during re-saturation of the site in the post-closure stage. Although indirect evidence for argillite self-sealing has previously been reported, from experiments performed both in situ and on samples, no direct observations of self-sealing have yet been made.For the present study, we performed a range of self-sealing experiments using a newly-developed triaxial compression cell placed within a nano-CT scanner with a 10 µm resolution. The body of the compression cell is X-ray transparent, allowing sample healing to be monitored directly. The samples contained an artificial fracture that had been generated in the laboratory, into which a fluid was injected. The fractures were orientated either perpendicular or parallel to the plane of anisotropy of the material. Our initial results demonstrate that when fluid is injected perpendicular to the plane of anisotropy, the flow-rate has no apparent influence on the kinetics of fracture closure. Permeability varies significantly, from 2.10-14 to 2.10-18 m2 over 116 hours. Post-test observations of the fracture lips show swelling that appears to be orientated perpendicular to the fracture plane and therefore parallel to the plane of anisotropy. Initial results for an injection parallel to the plane of anisotropy suggest that, in this case, the rate of flow affects the kinetics of fracture closure. For a flow-rate of 0.25 ml/min, closure begins after around one minute. In contrast, for a rate of 0.05 ml/min, it is necessary to wait several minutes before partial sealing of the zone is observed. The reduction in permeability is again significant, from 2.10-15 to 4.10-18 m2 over 96 hours. After completion of the test, swelling was observed in elongated zones that lie parallel to the fracture plane and therefore to the plane of anisotropy."

Jan 1, 2015

By V. Songmene, A. Tahan, J. P. Michaud

The machining of thin wall parts, often used in the aeronautical industry still creates a number of problems, including panel deformation. Quality and productivity are often affected. This study seeks to determine the optimal conditions for cutting in order to guarantee a competitive fabrication of parts while still maintaining quality and delivery deadlines. The studied model (Spar) is a typical structural part used in the assembly of airplane wings. The main objective of this study was to improve two performance aspects: surface quality finish (quality criteria) and the rate of cutting by stock removal (economic criteria). To achieve this objective, we used an evaluation process of the geometrical error issuing from the machine-tool. We also determined the stability zones of the machine-tool's dynamic system. Finally, a series of high-speed machining tests (finishing cuts) were conducted using an experimental structured approach (16 000 - 24 000 rpm). Profile measures of surface roughness and cycle times registered during trials allowed us to establish optimal cutting conditions. Surface roughness improved as well as cutting by stock removal. Four parameters were taken into consideration: axial depth of cut, chip load, spindle speed, and cutting fluid. Finally, the influence of the type of cutting fluid was evaluated to show that it did not significantly affect machining results.

Jan 1, 2006