Search Documents

By J. W. McCammon

WHEN times are booming and metal prices are high, most mining men pay little attention to the industrial mineral industry. However, when metal prices drop and mines close down, many mining eyes begin to scan the less glamorous non-metallic field. For some this proves a temporary diversion, but others find this branch of mining, with its generally more stable conditions, to their liking and enter it permanently. The resulting gradual influx of trained mining men into the industrial mineral industry ?has been one of several factors responsible for the rise in production of non-metallic materials in our Province. Another and ?perhaps the most important factor influencing the production of industrial minerals has been the growth in the population of British Columbia. Because most industrial minerals .are low priced and either heavy or bulky commodities they are normally sold on relatively local markets. Thus the extent of the development of the industrial mineral industry of a region is largely governed by the size of the population and the level of industrialization of that region. This point is well shown by com-paring population and industrial mineral production statistics for 1936, 1946, and 1956 (see Figure 1)9. Note that not only has the overall production rate grown with the population increase, but that the per capita production has risen greatly.

Jan 1, 1958

By Arnfinn Prugger

"The construction of the new Scissors Creek shaft at the Rocanville mine, the first potash shaft successfully completed in Saskatchewan Canada since 1979, is summarized here. Located 15km from the existing Rocanville surface plant, this new 6 m inside-diameter, 1121 m deep service shaft was built for fresh-air ventilation and access. Shaft construction in the Saskatchewan sedimentary basin involves sinking through five different rock-types: glacial tills, shales, sandstones, carbonates and salts. The first four rock- types are all water-bearing, and the salts will dissolve in water. This results in five different sinking challenges and requires five different shaft lining designs. The upper 580 m of rock (the till – shale – sands sequence) was frozen before sinking, and grouting methods were used for water control through deeper carbonate levels. Challenges that were faced and overcome during shaft sinking are reviewed, and ideas that future operators working in sedimentary basin environments might consider in order to avoid these difficulties are discussed.INTRODUCTIONThe Nutrien Inc. (formerly Potash Corporation of Saskatchewan Inc. / PotashCorp) Rocanville potash mine in southeast Saskatchewan, Canada has been in continuous production since 1971. Devonian potash, formed approximately 380 Mybp, is mined in a sedimentary basin environment at approximately 1000 m depth below surface in this area of Saskatchewan. The predominant use for finished potash products is fertilizer: potash fertilizer is concentrated and nearly pure KCl (i.e. greater than 95% pure KCl). Currently 10 potash mines are in operation in Canada, all in Saskatchewan. In 2018 Saskatchewan mines produced ˜ 23 million tonnes of finished potash products, which is approximately 35% of World demand of ˜ 66 million tonnes for the year (e.g. Nutrien Inc., 2019).In November, 2007 it was announced that the Rocanville potash mine would be expanded to increase production from 3.0 Million tonnes per year (Mtpy) to approximately 6.0 Mtpy of finished potash products, requiring an increase in hoisting capability from approximately 9.0 Mtpy to over 18.0 Mtpy. The Rocanville potash mine has historically been accessed through two shafts: a production and ventilation exhaust shaft, and a service and ventilation fresh-air shaft located approximately 200 m from each other. All surface offices, processing facilities, etc. are situated near these original shafts.A very important part of the recent Rocanville expansion involved the construction of a new service shaft (6 m diameter, 1121 m deep) for fresh-air ventilation and access, approximately 15km west of the existing surface plant. Once this third shaft was completed in 2015, the historical service shaft was converted to a second exhaust and production shaft. Three shafts are now available for mine access, ventilation and ore hoisting at Rocanville. As of December 31, 2017, annual nameplate capacity for Rocanville was 6.5 million"

Jan 1, 2019

By G. T. Lapidus, A. Garcés, O. J. Restrepo

"Colombian nickel laterites have historically been processed by pyrometallurgy. However, due to the depletion in ore grades, alternative processes are required. Hydrometallurgical processes, such as pressure acid leaching, have been proposed as alternatives to extract nickel from deposits with suitable characteristics. Such a leaching process requires high concentrations of acid to achieve acceptable extractions, and is not selective. In this study, an alternative aqueous alkaline glycine system has been employed to evaluate the leaching behaviour of a Colombian nickel laterite which contains 1.15% Ni, 0.12% Co and 41.1% Fe. Additionally, the effect of the addition of chloride ions, the use of a reducing agent and the application of a pre-treatment to improve the extraction of nickel were evaluated. Extractions of 4.63% Ni, 42.16% Co and 0.33% Fe were obtained using a 1M solution of glycine at pH 9. In addition, an increase in nickel extraction from 4.63% to 25.68% was achieved by applying a pre-treatment to the sample. The results show that even though nickel dissolution was much slower than in acid leaching, it was selective over other metals such as iron, proving the proposed method to have potential as a process for the extraction of nickel from Colombian laterites.INTRODUCTION Before 2010, most of the industrial operations used pyrometallurgical processes for the extraction of nickel, mainly in saprolitic regions of deposits, with greater contents of the metal. Nevertheless, due to the gradual depletion of such deposits, different hydrometallurgical processes have been studied as alternatives to process those nickel laterites with low grade and those which present problems of refractoriness due to the presence of acid consuming materials (McDonald & Whittington, 2008; Oxley & Barcza, 2013; Wang et al., 2012). However, such leaching processes require high concentrations of acid to achieve acceptable extractions and they are not selective. Facing lateritic nickel ore deposits containing high levels of acid consuming materials, an alkaline leaching medium becomes an advantageous alternative over acidic media, due to the increase in selectivity and decreased corrosiveness and reagent consumption (Tanda, Eksteen, & Oraby, 2017). Unlike conventional acidic reagents used for metal recovery, alkaline reagents can selectively dissolve the desired metal, leaving in the solid residue other elements such as iron, magnesium and aluminum, which are problematic in subsequent stages of metals separation and recovery. Furthermore, there are no serious corrosion problems associated with alkaline leaching, even at higher reagent concentrations, or at elevated temperature and pressure (Ntumba Malenga, Mulaba-Bafubiandi, & Nheta, 2015)."

Jan 1, 2017

By G. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment. The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate. The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

By H. Mindivan

In the present study, the feasibility of recycling AA6061 Al alloy chips by a combination of ciyomilling, cold compaction and hot extrusion processes was investigated. Furthermore, the effect of Al powder addition to the recycled Al alloys chips on the mechanical properties was investigated. The characterization of recycled Al alloys was made by structural examination and mechanical tests (hardness, compression and dry sliding wear tests). The results indicated that by increasing wt. % of Al powder added to the recycled Al alloy chips the studied properties (the density, hardness, compressive strength and wear resistance) increased due to reduction of porosity in the recycled Al alloys.

Jan 1, 2011

By T. W. Wong, M. A. Whitney, A. Hadadzadeh

Uniaxial compression tests were performed on cylindrical specimens, 10mm in diameter and 15mm in height, machined from an extruded AZ31B magnesium billet. The tests were conducted under isothermal conditions to a true strain of 0.5. The study compares macroscopic flow anisotropy between the extruded (ED) and transverse (TD) directions in the temperature range of 300°C to 500°C, and strain rate range of 0.001s-1 to 1s-1. Compression of ED specimens at low strain rate (0.001s-1) exhibited axisymmetric flow, and no significant differences were observed between geometries of specimens deformed above 350°C under the same strain rate. Deformation of TD specimens at low temperature and/or low strain rate resulted in elliptical cross-sections, with the anisotropy of flow being less significant at higher temperatures. Other studies performed using rolled plates have proposed that pyramidal slip and cross-slip at higher temperature eliminate the effects of initial texture, while the dominance of prismatic slip at lower temperatures will result in anisotropic flow. It is believed that the initial fiber texture common among extruded HCP-structured materials plays a role in the anisotropic deformation behaviour observed in the extruded specimens

Jan 1, 2015

By T. C. Murphy, W. Taciuk

In 1966, the Iron Ore Company of Canada commissioned a wet magnetic scavanging plant for the recovery of fine magnetite values p.resent in spiral tailings discharged from a spiral gravity separation process. The plant includes dewatering, grinding, classification, thickening, mini-wedge screening, and primary, secondary and tertiary wet magnetic separation stages. The source of feed varies in quantity and quality, so the original design included variable operational procedures to deal with these conditions.

Jan 1, 1972

By P. Au, P. Patnaik, H. Saari, D. Y. Seo, S. Bulmer

Ti-48Al-2Cr-2Nb-xW (where x = 0, 0.5, and 1 at. %) powders were consolidated by hot isostatic pressing (HIP). The consolidated samples were solution heat treated above the a-transus followed by stepped cooling to room temperature. Selected samples were subsequently aged at 950 °C for up to 72 hours. The post-heat treatment microstructure was examined by optical and electron microscopy. It was found that increasing holding time above the a-transus generated a more homogenous microstructure. Utilizing the stepped cooling sequence, especially with a transition temperature of 1270 °C, massively transformed gamma (Ym) was diminished. Aging caused coarsening of the fully lamellar microstructure in the 0%W and 0.5%W samples while almost no coarsening occurred in the 1 % W sample. Precipitates began to form during aging in samples containing W. The precipitates at the lamellar interfaces are fine and have a needle like shape, while precipitates at the lamellar grain boundaries are coarse and circular in shape. The size and number of the precipitates depend on aging time and the level ofW content.

Jan 1, 2006

By W. Hawker, A. M. Ivana

"Pressure oxidation is used to liberate gold from refractory sulphide ore and concentrates with over fifteen autoclaves in operation. Despite the importance of pressure oxidation, the autoclave chemistry and chemical thermodynamics are not well established. For example, there is no consensus on aqueous iron speciation or stability of jarosite phases. Additionally, there remains questions about basic ferric sulphate formation and stability. In addition to a review of the current state of knowledge, a methodology to study the ferric precipitation reaction and relate the results to chemical thermodynamic predictions is presented which will be used to accurately define the phase boundaries of the iron precipitates in the future (hematite, jarosite and basic ferric sulphate).INTRODUCTION With declining availability of orebodies that respond to simple leaching conditions, pressure oxidation has become a prevalent technology to liberate gold locked in sulphide mineral matrices. Gold pressure oxidation was established 32 years ago, with McLaughlin being the first facility in 1985 (Thomas & Pearson, 2016). Pressure oxidation is carried out at elevated temperatures ranging from 180 to 240°C as shown in the summary of operations in Table 1 (Ruonala et al., 2016; Fleming, 2010).A considerable amount of research has been done to study iron solubility and precipitation under autoclave conditions (Tozawa & Sasaki, 1986; Umetsu et al., 1977; Sasaki et al., 1993; Fleuriault, 2016; Cheng & Demopoulos, 2004; Papangelakis et al., 1994; Yue et al., 2003). These reports provide a description of the process chemistry and iron behaviour in the autoclave. However, there remain questions about the type and stability of aqueous species and solid phases. This detailed information is required to build a robust chemical thermodynamic model of the system, allowing for equilibrium and kinetic reaction limitations to be discerned."

Jan 1, 2017

By A. A. Shirzadi, E. R. Wallach

"Liquid gallium has been used successfully to modify/remove the surface oxides prior to diffusion bonding similar and dissimilar nickel-base superalloys. Using this approach, bonds in nickel-base superalloys with ""virtually invisible interfaces"" were produced, and the compositions in the bond region were very close to those of the bulk alloys. Room temperature tensile and bend tests showed no preferentially failure at the bond lines. Creep tests on samples made between two different Inconel alloys also showed failure away from the joint, i.e. in the parent metal of the Inconel alloy with lower creep resistance. The high temperature lifetimes of these samples were as long as those of the unbounded Inconel, confirming that the joining approach has no adverse effect on the nickel-base superalloys being joined."

Jan 1, 2006

By R. Esteban, D. Runnels, J. Torrealba-Vargas, G. Couture

"Data handling is an important step in the development of a simulator of a mineral processing circuit. The model requires representative data of the scenario to be modeled. The model development involves protocols that must be followed very closely to complete a successful project.Data handling of large and diverse datasets (metallurgical test results, geological data, mining models, historical data, etc.) is a key element of the model. The information needs to be processed, reconciled, interpreted, modeled and presented to support the design or the optimization of a mineral processing plant.Best practice recommends that teams from different disciplines (such as mining, metallurgy, geology and environmental) interact to define the most important variables that could influence the simulator. For example by adopting a geometallurgical approach in the earlier stages of the project, it is possible to consolidate the number of main ore rock types in a testwork program (saving money and time) by involving geologists and metallurgists in the sample selection and data interpretation.Planning the development of a model involves an understanding of the software capabilities but also the limitations and the magnitude of the data required to calibrate the model in case of changes in the project.A successful model requires a deep understanding of the circuit to be modeled and thus plant personnel should be considered as members of the team.This paper describes the use of the "state of the art" tools for data analysis, simulation and optimization; and shows three practical examples of the use those tools in the design of mineral processing plants."

Jan 1, 2015

By Christopher Riley

A relatively unexplored lead zinc deposit lies about 12 miles northwest of Revelstoke, B.C., in the highly metamorphosed Monashee Group of rocks of the Shuswap Terrane, Precambrian in age. Host rocks are of sedimentary origin and consist of gneisses, schists, marbles and quartzites with intermediary types. The marbles and quartzites provide good horizon markers. Using these it is possible to interpret the controlling structure which is a syncline overturned to the north, dipping south at about 45°, and plunging east at about 12°. The syncline is truncated at about halfway of its length on a peak on the west side of which a partial cross section together with superimposed minor folds may be seen. The quartzites and the two marble beds may be traced over much of the structure. There are two lodes, above the marble and below the quartzite, which converge eastward and which are the exposed edges of the same host bed -an impure limestone.

Jan 1, 1961

By W. G. Deeks

CANADIANS are world leaders in marketing metal and mineral products. Noranda Sales Corporation Ltd. is an international metal and mineral product marketing company operating from Toronto and London, England, where it operates a wholly owned sales subsidiary and is a 50% partner in Rudolf Wolff and Company Ltd., a charter member and the largest metal broker on the London Metal Exchange. Noranda Sales employs 97 people, of whom 52 are university trained and professionally competent in international resource product marketing. We market for 19 companies or divisions in the Noranda Group and 39 companies for whom we act as agent, consultant and purchaser of resource production. Our business in 1976 was 1.5 billion dollars carried out in 45 countries and covering 24 products and materials. Today, ownership of most of the mining industry in Canada has transferred back to Canadians, and this is said with the knowledge that a significant part of the Canadian industry has been Canadian owned and managed from its very early days. Noranda Mines Limited is such an example. It was born in 1922 as the result of a copper-gold showing at Noranda, Quebec, discovered by Ed Horne, a prospector, financed with a grubstake by a syndicate mainly composed of New York businessmen. Shortly after the discovery, when the shares of the company had risen, the syndicate was sold to Canadian interests and, since that time, Noranda has been dominantly Canadian owned and certainly Canadian managed. Today, over 90% of Noranda's shareholders are Canadian, who hold an equivalent percentage of the stock.

Jan 1, 1977

By Z. F. Lodhi, J. H. W. De Wit, H. A. Terry

Zinc and its alloys have been extensively used as replacements for Cadmium coatings in aeronautical and automobile industries. Zn alloys with low Co or Fe have been highly investigated but coatings with higher amount of Co are very difficult to achieve due to anomalism associated with these coatings. Anomalous Zn-Co-Fe alloy is a relatively recent addition to the family of Zn alloys. It is found that the addition of Fe in the electrolyte assist in overcoming the anomalism. In this research Zn-Co-Fe alloys especially with higher amount of Co (>15%) and Fe (~1%) are investigated, after overcoming the anomalism associated with its deposition, and the corrosion resistance is compared with pure Zn and Cd. It is found that an increase in Co to higher than 25 % accounts for a shift in the OCP to a level near Cd yet keeps it electronegative to steel. The coating shows superior corrosion resistance, in terms of its sacrificial and barrier properties in 3.5% NaC1 as compared to Zn and Cd.

Jan 1, 2006

By Bob Drew, Goran Vukovic, Bojan Zivanovic, Klaus Gamweger

Reaction bath temperature is a major factor in processing liquid metals and in many applications where a balance between process duration and temperature has to be found to run a procedure efficiently. Also extremes of temperature can decrease the output of a process if too cold or even make it impossible, conversely overheating can be detrimental to both the product and furnace integrity. With the help of the new online temperature measurement system very accurate monitoring of the process is possible in contrast to the current routine practice where the temperature is measured periodically with dip thermocouples. The system works with a digital, fiber optic pyrometer, which is embedded in a refractory housing. Installation in the lining is possible below liquid level as nitrogen is blown to keep the system open and to ensure continuous sight from the optical head of the pyrometer to the molten metal through the tuyere. This permanent temperature measurement gives optimal process control with the potential of taking appropriate actions at an early stage enabling proactive process control. Therefore energy savings and even process endpoint detections can be realized.

Jan 1, 2015

By J. Dennett, M. Faris, M. Antonio, M. Collins, N. Tuffrey, R. Ellenwood, V. Reddy

"In January 2012, AngloGold Ashanti Córrego do Sítio Mineração, with assistance from Sherritt International Corporation, commissioned a new autoclave for pressure oxidation of refractory gold concentrate at the Córrego do Sítio operation in Brazil. Start-up of the plant occurred in a few weeks and enhanced gold recovery was realized almost immediately, with 94% gold extraction achieved in carbon in leach (CIL), compared to less than 70% without pressure oxidation. This paper describes start-up and commissioning of the plant and provides an overview of plant performance over the last five years.INTRODUCTION In 2008, AngloGold Ashanti purchased the former São Bento property from Eldorado Gold, which, along with AngloGold Ashanti’s existing Córrego do Sítio mine, was renamed AngloGold Ashanti Córrego do Sítio Mineração (AGA Mineração). Later that year, the Sherritt Technologies division of Sherritt International Corporation (Sherritt) was contacted to begin batch and continuous pilot plant tests to determine the amenability of the AGA Mineração refractory gold concentrates to the pressure oxidation process. Based on the results of the batch and pilot plant tests, AGA Mineração requested basic and detailed engineering studies to be conducted by Sherritt, eventually leading to commissioning of the plant in January 2012. AGA Mineração’s plant is located in southeastern Brazil in the state of Minas Gerais, near the city of Belo Horizonte. AGA Mineração`s Phase 1 mine plan covers three sites in the Laranjeiras, Carvoaria Velha and Cachorro Bravo ore bodies, and is designed to process 60,000 tonnes of refractory gold concentrate per year to produce 140,000 ounces of gold per year with an 11 year life of mine (AngloGold Annual Financial Statements, 2010). Recovery of gold at AGA Mineração is based on Sherritt`s pressure oxidation technology for refractory gold concentrates (Berezowsky et al., 1991; Collins et al., 2011a; Collins et al., 2011b). This process had previously been applied to the recovery of gold at the São Bento site (Carvalho et al., 1988; de Silva et al., 1989), in a plant that was operational between 1986 and 2007 (Silva et al., 2004)."

Jan 1, 2017

By Haibin Ma, Jie Song, Qingyou Han, Xiaoming Wang, Wei Vian

In the grain refinement of aluminum, Al3Ti and TiB2 particles are introduced to reduce the casting grain size down to 200 micrometer level, which makes cold working possible. The particles are brought in by the addition of Al-Ti-B type master alloys. It is generally believed that TiB2 particles are stable and nucleate a-Al grains in solidification in the presence of extra titanium than the stoichiometry of TiB2 from the dissolution of Al3Ti particle in the master alloys. Titanium in solution either form Al3Ti layers on the surface of TiB2 particles or as solute to promote the nucleation and to restrict the growth of a-Al grains. However, a consensus on a grain refinement mechanism is still to be reached due to the lack of direct observation. This paper presents finding on the TiB2/Al3Ti interfaces in an aluminum matrix. It demonstrates a strong epitaxial growth of Al3Ti on the surface of TiB2 particles, a sign of the formation of an Al3Ti layer on the surface of TiB2 particles in grain refinement practice. The Al3Ti layer has a crystal coherency with a-Al and hence offers a substrate for heterogeneous nucleation of a-Al grains.

Jan 1, 2015

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Previous testwork by the authors has indicated that both granular coconut shell based activated carbon and a new microporous carbonaceous bead, Lewatit® AF 5, are highly effective in improving the oxidation kinetics and decreasing the elemental sulphur yield when assisting the atmospheric oxidation of pyrite. While the two carbon catalysts show similar results and improvements to the pyrite oxidation, there are differences between them. For example, the activated carbon assisted oxidation showed faster kinetics than the AF 5 assisted oxidation, while elemental sulphur seemed to remain adhered to the surface of the AF 5 after oxidation when much of the elemental sulphur formed during the activated carbon assisted tests was found in the oxidation residue. The objective of this paper is to investigate the differences between the two catalysts through the use of scanning electron microscopy, photography, Raman spectroscopy, surface chemistry analysis, and Brunauer-Emmett-Teller (BET) surface area analysis. With this investigation the authors should be able to achieve a better understanding of the surface chemistry of the two carbon catalysts (i.e. functional groups, charges, acidity etc.) and help explain the strengths and/or the weaknesses of the catalysts when applied to the atmospheric oxidation of pyrite.INTRODUCTION Previous research conducted by the authors, indicated that both a granular coconut shell based activated carbon (activated carbon) and a microporous carbonaceous bead, Lewatit® AF 5 (AF 5), acting as a catalyst enhanced atmospheric pyrite oxidation in ferric sulphate media by approximately 40% when compared to unassisted oxidation and that elemental sulphur yields were increased from 23% to approximately 69 and 63% when assisted by AF 5 and activated carbon respectively (Cowan, Jahromi, & Ghahreman, 2017). The study indicated that although total pyrite oxidation assisted by the two catalysts was similar, differences were noticed in the impact that the two catalysts had on the outcome of the oxidation. Kinetic curves in the Cowan et al. study indicated that atmospheric oxidation of pyrite seemed to reach completion after 48 hours of oxidation when assisted by activated carbon. A similar trend was noticed in the kinetic curves for oxidation when assisted by AF 5, however the oxidation curve did not reach completion until approximately 96 hours (Cowan et al., 2017). This observation indicated that the kinetics of pyrite oxidation are enhanced by both catalysts, oxidation kinetics are much faster when assisted by activated carbon rather than AF 5."

Jan 1, 2017

By L. S. Brooks

TIMBER HANDLING presents a problem for any mine where appreciable amounts are used. This problem is accentuated where the shaft compartments are too small to allow a loaded timber truck to be lowered in the mine cage. When Normetal Mining Corporation, Limited, found it necessary to resort to square-set mining it faced this problem of getting large quantities of timber down a shaft that was also required for hoisting ore. A 'timber car' that could be suspended under the cage was developed to overcome this difficulty. Production started at the Normetal mine in 1937, at the rate of 250 tons per day. In 1938 a winze, known as No. 3 shaft, was sunk from the 800-foot level ?to the 1,385-foot level. This was later raised to surface and then deepened to 3,275 feet in three stages and became the main production shaft. The portion of the mine below the 3,070-foot level is serviced by a winze, locally referred to as No. 4 shaft, which has been developed for stoping down to the 3,990-foot level and which has been deepened to the 5,365-foot level. No. 3 shaft has two hoisting compartments, each 4 ft. 6 in. by 5 ft. 0 in. inside the timbers, through which the ?ore must be hoisted and timber and supplies lowered.

Jan 1, 1956

By J. W. Cox, W S. Jones, A E. Chase

For a long time the Oil Industry has been looking for a logging tool which can determine the quality of the cement job behind casing. Older methods such as Temperature Surveys and Radioactivity Surveys might detect the presence of cement behind the casing, but short of production tests, it was impossible to tell that the producing zones were adequately sealed off from adjacent zones. A new logging method, which is called the •Cement Bond Log, operates on the principle that a sonic pulse transmitted by the casing is greatly attenuated when the casing is strongly bonded to an outer annulus such as cement. The down-hole tool consists of a source of sonic energy which is detected by a receiver situated a few feet away from the source. The amplitude of the detected energy is measured and the resulting signal transmitted to the surface where it is recorded versus depth. Amplitude is a function of attenuation and thus the log is readily interpreted.

Jan 1, 1961