Search Documents

By J. Armitage, J. Erskine

Feed level and thickness measurements are essential in the optimization of an electric arc furnace. A precise measurement of the feed thickness and level gives operators the ability to increase the smelter efficiency and reduce the maintenance cost. Hatch has developed a radar system which is an affordable, low maintenance, and accurate level measurement system. The radar units can be installed across the furnace to measure the feed level and the feed thickness can be calculated with one slag level sounding. The present paper describes the development of radar systems as a process optimizing tool by furnace controls. The authors will discuss the challenges involved in installing eight radar units on the roof of a six-in-line electric furnace.

Jan 1, 2015

By D. M. MacLean

THE property of Howey Gold Mines, Limited, is situated at Red Lake, Ontario, one hundred and seventy-five miles east of Winnipeg and eighty miles north of the Canadian National railway. The mine has been a continuous producer since April, 1930, and, at present writing, a total of 3,042,690 tons has been hoisted, giving a production of $6,422,858.55, for a grade of $2.32 per ton. From 1,064,477 tons mined during the past two years, however, the yield has been only $1,389,607.03, or $1.41 per ton (gold at $20.67). Present output is at the rate of about 1,470 tons. per day. THE ORE-BODY AND WALL-ROCK: The Howey ore-body is part of a quartz porphyry dyke, which has. intruded an area of greenstone. The dyke strikes north 65° east, and its dip varies from 85° to the south at the surface to practically vertical below the. 1,000-foot horizon. Both along the strike and on the dip, the width of the dyke varies from 25 to 200 feet, the widest portion occurring below the 1,000-foot level. To the east of the ore-body, the dyke increases in width and finally splits into tongues of porphyry enclosed in greenstone, diorite, and congloJ11erate. To the west, it passes into the adjoining property, its width at the boundary being 100 feet. The rock in the ore-body is hard to drill, but, because of numerous horizontal slip-planes, it breaks well when blasted. This characteristic makes it possible to break large breasts or benches with a relatively small number of holes. The ore broken in this manner is consequently quite coarse, a large part of it requiring secondary breaking.

Jan 1, 1938

By R. O. Burt

"IntroductionThe introduction to this section on gravity concentration indicated the wide range of equipment types that exist for the concentration of minerals, in what is the broadest size range of any concentration process.The equipment described in this chapter includes jigs, tables and sHme plant equipment. In contrast to the equipment described in the two succeeding chapters, this range of equipment, in nearly every instance, superimposes a mechanical movement on the fluid motion to effect separation of the valuable mineral from the waste mineral. The motion may be vertical Gigs), reversing (tables), or rotary (slime plants): however, in common they ""dilate"" the bed of particles to allow preferential settlement of the heavier particles.Description of Process UnitsJiggingJigging is the sorting of different minerals by stratification, based on the movement of a bed of particles relative to a fluid in a vertical plane.The basic construction of a jig is shown in Figure 1. Essentially it consists of an open tank filled with a fluid, normally water, with a horizontal jig screen at the top and with a spigot in the ""hutch"", or bottom compartment, for removal of heavies. The jig beri consists of a layer of coarse heavy particles (ragging) on the jig screen. This ragging is of a specific gravity between that of the minerals it is intended to separate.In operation the bed is made fluid by a pulsating current of fluid to provide stratification. On the upward or pulsion stroke the bed of ragging and slurry is normally Hfted as a mass, then as velocity of the upcurrent decreases it dilates, loosening the whole mass. On the downward or suction stroke it closes slowly again. The ideal is to control this dilation of the bed of material so that the heavier and smaller particles penetrate the interstices of the bed, while the larger heavies fall under a condition akin to ""hindered"" settling."

Jan 1, 1989

By Floyd Smith

Based on underground observations made in .the coal mines of the Dominion Coal Company Ltd., this paper deals with the stress phenomena in the approach roads and headways and in the gob areas associated with the longwall method of total extraction. The deformation of roadways during development and the deformation of roadways during the total extraction period is delineated and presented in graphical form .. Conclusions are made as to the feasibility of the introduction of the retreat method of longwall extraction in one of the colhenes. The importance of future studies are enumerated, especially. those pertaining to the determination .of the opti.m.um sizes of protective pillars and to increasing the efficiency of the current methods of artificial roadway support.

Jan 1, 1967

By W. A. Jones

THE estimation of the average value of gold ore involves many considerations, among them the correct sampling of the deposit, the dilution by waste, and the loss of high-grade fines. It is a common experience that, after all these factors have been evaluated, adjustment of the assays is necessary before satisfactory agreement between the calculated mine grade and the mill heads is obtained. In fact, at many mines the latter correction overshadows all others in the preparation of routine estimates. For this reason it is proposed to deal only with the mathematical treatment of mine assays and the problem of bringing estimates into conformity with the corrected mill heads. Mine assays differ from physical measurements because the range of values is very great and these are not symmetrically distributed above and below the average, there being fewer high than low results. There is no widely accepted mathematical procedure for determining the average of series of measurements which exhibit these characteristics. Customary practice consists in empirically reducing high assays until a satisfactory agreement with mill heads is reached. It was thought that more confidence could be placed in grade estimates if a logical basis for calculations could be devised .. In an attempt to find a fundamentally sound procedure, amenable to practical application, many series of assays comprising over 235,000 channel samples (1) were studied at Hollinger Consolidated Gold Mines, Limited. Such an investigation could only be made where records covering many years of operation are available and where tabulating and calculating machines are in use. The results are recorded in the hope that the relationships noted for the large groups of assays used are of fundamental character and that the data will be useful to others dealing with the problem of grade estimation.

Jan 1, 1943

By D. S. Campbell

THE chief factors influencing the decision to build the Big Missouri mill underground were the topography of the country and the climate. The location underground assured certain saving in the cost of operation, such as the hearing of the mill, shovelling snow, and handling ore, which, over a period of time, would offset the greater initial cost of the mill excavation and machinery installation underground, as compared with the cost of a like plant on the surface. At Gilman, Colorado, where conditions are somewhat similar, the Empire Zinc Company, at their Eagle mine, are treating their lead-zinc ore in a mill built entirely underground. Company officials made a study of this plant before proceeding with the mill at Big Missouri. LOCATION, CLIMATE, TOPOGRAPHY The Big Missouri mine is situated on the Upper Salmon river, 22 miles north of Stewart, B.C., which is at the head of Portland canal, a narrow natural channel which penetrates 100 miles inland from the coast into the Coast Range mountains. Stewart, the distributing centre for the district, is about 600 miles north of Vancouver. The Big Missouri claims lie on and down the sides of the Big Missouri ridge, which extends north and south between the Salmon River and Cascade Creek valleys. The ridge rises to an elevation of 3,600 feet, is about half a mile wide, and to the east slopes down to the Joker flats in Cascade Creek valley. The Big Missouri camp is located on the flats at elevation 2,800 (see Figure 1). Preliminary development of the property took place from this point with an adit driven under the ridge. The western side of the ridge slopes steeply down to the Salmon glacier at elevation 1,900. Ore found on the 2,850 level extended down, and, in order further to explore the ore-body, the 2,850 level was driven through to the west side of the ridge, a surface incline tramway was built, and a lower tunnel driven at elevation 2,350, five hundred feet below the original 2,850 level, from the west side of the ridge. This tunnel development avoided the necessity of sinking, which would have been costly, as the mine makes a great deal of water (see Figures 1 and 2).

Jan 1, 1938

By G. Van Weert, O. Wang

"As part of a general review of processing double refractory ores through Barrick Gold’s autoclaves / CIL facility at Goldstrike, blanking the preg robbing native carbon in the process solids with hard (m.p. 55 - 60 º C) paraffin wax was studied, specifically in relation to pressure oxidation. The improvement in CIL gold extraction was found to depend on the wax addition point, with hot, dry contacting of the ore in the presence of wax - prior to POX - yielding the largest, most consistent improvement in gold extraction.INTRODUCTIONDouble refractory gold ores present two barriers to gold extraction. The first is generally a physical barrier: the gold is encapsulated or dispersed in a matrix which is impervious to the gold lixiviant. In most cases, including Carlin Trend, NV, deposits, this involves a pyrite or arsenopyrite matrix, although minor gold may also be dispersed in competent silica (quartz) or iron oxides. Gold can be rendered accessible by oxidative destruction of such sulphide matrices. At Goldstrike this is practised by roasting and autoclave oxidation (Thomas, 1994). It is the latter route to which this paper refers.The second barrier refers to the actual gold recovery. Gold may be extracted from the pressure oxidized solids with cyanide, forming a gold cyanide complex. One characteristic of this complex is that it adsorbs on graphitic surfaces. This is taken advantage of on a large scale by gold millers, who use manmade activated, i.e., graphitized carbon particles to remove the gold from solution during leaching: the Carbon-In-Leach, or CIL process. The gold cyanide bearing carbon particles are larger than the ore solids and can be separately recovered by screening. Goldstrike uses the CIL technology to recover gold. The second barrier becomes problematic when the ore naturally contains graphitic orcarbonaceous material, hereafter referred to as native carbon (versus the man-made activated carbon). This material may also adsorb gold cyanide in competition with the activated carbon. Since the native carbon is ground with the ore it is much smaller than the activated carbon. Any competition between the two carbons may produce a loss of gold from the pregnant leach liquor to the process tailings. This phenomenon is called “preg robbing”. Goldstrike ores come from the Carlin trend, which is known for the occurrence of native carbon (Adams & Burger, 1998; Schmitz, Duyvesteyn, Johnson, Enloe & McMullen, 2001; Tretbar, 2004)."

Jan 1, 2012

By G. H. Charlewood, J. W. McBean

"One hundred years after being developed, the diamond drill is still an essential tool in mineral exploration. The basic principle is unchanged, but the technique has been revolutionized, particularly in the past fifteen years. The cost of core drilling has not kept pace with the rising cost of living. The price of machinery, supplies and labour in drilling has doubled and trebled since 1946. Some of the techniques which have made it possible to hold the price line are described."

Jan 1, 1967

By Sib N. Mukherjee

Main ventilation fans are used in all the mines and they run continuously 24 hours a day and 365 days in a year. Any improvement in their performance can lead to considerable power saving. The basic principle for selection, operations, and related measures are discussed in brief in the paper. The contributions of different elements of mine fan on its performance are discussed in brief. The means to improve efficiency of a running fan is also discussed and the importance of saving even 1 Kwh is elaborated. It is found that the cost of the energy saved may even permit a replacement fan to be procured in a few years time.

May 1, 2007

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds. Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a ?diamond friendly? method of comminution. Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso).

Jan 1, 2012

By D. Atkinson

"Porphyry molybdenum-tungsten mineralization on the east flank of Hudson Bay Mountain crops out over 5 km2 and is intersected to depths of 2 km. Features such as a hornblende-biotite aureole, mineralogical zoning and dike, vein and fracture geometries within lithologies of the Middle to Lower Jurassic Hazelton Group and Cretaceous Skeena Group reflect an intrusive complex, the Upper Cretaceous to Early Tertiary Hudson Bay Mountain stock which has been intersected by drill holes. The stock is believed to be the mineralizing agent. A southeast-dipping granodiorite sill has been outlined by drilling within the Hazelton Group. Molybdenite and scheelite veins cut all rock types; however, the granodiorite sill hosts a higher density of fine-grained, banded, quartz-molybdenite and pegmatitic quartz-molybdenite veins reflecting a competency contrast between the intrusive sill and other country rock. Due to the relative abundance of these veins, grade is higher within areas of the sill. Above the 15000£ cross-cut 20.6 million tonnes grading 0.401% MoS2 and 0.041% W03 have been defined. During exploration of the deposit sampling procedures had to be adjusted because of the nugget effect attributed to drill intersections of banded and pegmatitic veins.IntroductionMolybdenite was discovered in outcrop at the foot of Kathlyn Glacier on Hudson Bay Mountain and first reported by the Geological Survey of Canada in 1944. The deposit has several names: Hudson Bay Mountain or Glacier Gulch, both after its location, and Yorke-Hardy after the original staker.The deposit is on the east flank of Hudson Bay Mountain, 9 km northwest of Smithers, west-central British Columbia, within NTS area 93L/14 (54° 49' North, 127° 18' West, Fig. 1). Hudson Bay Mountain, on the southern edge of the Bulkley Valley, is a dominant topographical feature reaching 2590 m elevation. Mineralization is partly overlain by the Kathyln Glacier which is visible from Highway 16. Access to the 3100 m of underground development is from a portal at 1066 m elevation on the east slope of Hudson Bay Mountain."

Jan 1, 1995

By Fred V. Seibert

The Functions and the Responsibilities of the Institute The Canadian Institute of Mining and Metallurgy is unique. ln addition to the welfare of its members, it has a real interest in the welfare and promotion of one of Canada's largest and most important basic industries. It is because of this that the membership is composed of both individual and corporate members. The individual members are both technical and non-technical (Members and Associates). Both Members and Associates have the same status in the Institute and all are interested in the welfare of the mineral industry. The aims and objects of the Institute 11re twofold. The education and welfare of its individual members and the sound promotion and welfare of the mineral industry. Perhaps it might be well if we reviewed these aims and objects as stated in our Constitution: "First - To promote the arts and sciences connected with the economical production of valuable minerals and metals, by means of meetings for the reading and discu11ion of technical papers, and the subsequent distribution of such information as may be gained throo.gh the medium of publications". It cannot be denied that we have do ne a good job in this particular phase of our work. Nevertheless, there is still room for improvement. It has been suggested that we might have more discussion and, on occasions, more criticism of our papers and programmes. This can best be done if the authors will have their papers prepared in sufficient time to permit of preprints being made availa1ble before the meeting at which they are to be presented.

Jan 1, 1950

By W. J. Farley

Location and History The Sherritt Gordon mine is in northern Manitoba, one hundred miles north of The Pas and forty miles northeast of Flin Flon. The original discovery was made by a Cree indian, Philip Sherlett, in 1922. The claims lapsed in 1924 to be re-staked and optioned by various mining groups who carried out a certain amount of development work before relinquishing their options. In 1927 the present Company, Sherritt Gordon Mines, Limited, was formed to take over the property. Production commenced in 1931, but in the following year operations were suspended and it was not until 1937 that the prevailing price of copper pemitted resumption as an economic operation. The mine has operated continuously from that time to the present. Total production to the end of 1947 has been: Copper . . . . . . . . . 301,813 . .,345 pounds Zinc . . . . . . . . . . . 112,636 tons of concentrat (50% zinc) Gold . . . . . . . . . . 83,070 ounces Silver . . . . . . . . . 2,651,317 ounces General Geology The consolidated rocks in the vicinity of the mine, all of Precambrian age, are a series of gneisses and form a part of a great area of what are known as the Kisseynew gneisses. The Sherritt is the only known economic base-metal deposit to occur within the Kisseynew series. Extreme metamorphism has produced recrystallization that has imparted a decided igneous-like texture to many of the units. However, the gneisses are predominantly of sedimentary original although the most basic member, a hornblendegarnet gneiss, is considered to be an altered basic flow. Figure 1 illustrates the intricately folded structure and the succession of roe types. The footwall enclosing members are of sedimentary origin and represent quartzite and arkosic and greywacke derivatives. The contact footwall member is gneissic quartzite, a medium to coarse grained rock composed mainly of quartz with minor altered feldspar (orthoclase and plagioclase), muscovite, chloritized biotite, and magnetite. Most phases of this unit show varying degrees of granitization.

Jan 1, 1949

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallisation and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. In an expansion or a new project, a large component of the capital cost can be associated with the pressure leach step and process engineers frequently look for opportunities to mitigate costs. This paper examines a new route for increasing the capacity of an exothermic pressure oxidation leach for sulphide concentrates, sulphide and phosphide mattes and alloys.

Jan 1, 2004

By B. K. Gorain

"The Air-Metabisulfite (AMBS) process has been developed to treat complex copper, molybdenum and precious metals (gold, silver) bearing ores using brackish and sea water. This process was able to produce significantly better copper concentrate grades and higher recovery than possible using conventional lime and/or cyanide based processes for certain complex ores with high sulphide gangue minerals. The AMBS technology in now used commercially following a rigorous evaluation process emanating from laboratory curiosity to plant applications. In addition, many projects have embraced this technology at a feasibility level involving various complex ore bodies.This paper presents a summary of the findings from testing the AMBS technology on various ores types. Experiences gained from this successful development from bench to piloting and then to plant applications are also presented in this paper.INTRODUCTIONProcessing of sulphide copper, molybdenum and precious metal ores typically involves flotation of copper bearing minerals while depressing non-sulphide and other non-copper sulphide minerals such as pyrite, pyrrhotite and sometimes arsenopyrite. Though in many precious metal ores, the values are in these sulphide minerals as well. The conventional method employed in the industry to produce a saleable copper concentrate requires depression of these non-copper sulphide minerals using an alkaline pH above 9.5, though 10.5 to 11.5 is more common. Alkalinity is controlled by the addition of a pH modifier. Lime is normally employed as a pH modifier due to its relatively low cost; however, the costs associated with adding lime can be significant and the effectiveness of lime as a depressant could be drastically reduced when the process water supplied to the flotation circuit contains high level of dissolved salts. In some cases, a small amount of cyanide is used along with lime to depress non-copper sulphide minerals especially when its proportion to copper sulphide minerals in the ore is higher than three."

Jan 1, 2016

By A. G. Roach

Introduction The plant described in this paper is located at Coniston, Ontario, the smelting centre of the former Mond Nickel Company. Coniston is situated some eight miles east of Sudbury on the main line of the Canadian Pacific railway and on the Toronto-Capreol branch of the Canadian National-railways. The plant is now under control of the International Nickel Company, as a result of the merger of the two companies in 1929. The smelter proper includes four 50-in. by 240-in. blast furnaces and five 13 ft. by 30 ft. converters, and has a capacity of about 65,000 tons of ore charge per month. As accessories to the smelter there are a mill, where some 10,000 tons per month of low-grade ores are concentrated, and the sintering plant, which is the subject of this paper. The present 6-unit sintering plant replaces a former 4-unit installation. Here, fine ores, concentrates, and flue-dust are sintered on Dwight-Lloyd machines, the sinter produced being charged into the blast furnaces. At the time of writing (1931), only the concentrator is operating at capacity, due to present world conditions.

Jan 1, 1932

By Atul Bhatnagar, M. P. Sinha, Md Zahid Ahmad, Pallav Garg, Sanjay Kumar Singh, Shashi Ranjan, An Ecolab Company Nalco Water

"Froth Flotation is undoubtedly one of the most critical processes in coking coal washing plants. This work was carried out at Bhelatand Coal Preparation Plant of Tata Steel was with an objective of cost optimization in fine coal processing. The sources of raw coal for the plant include coal from underground mines of Jharia coalfield and procured open-cast raw coal. Coal from different sources vary in quality and possess different floatability characteristics.Synthetic collector is being used in plant as a flotation reagent. An alternate collector with new chemistry was developed for reducing total treatment cost without compromising product yield and quality. A series of laboratory tests were conducted to assess the performance of various sources of raw coal and plant scale trial was started. At first, the new generation coal collector was entirely substituted with the existing collector in the laboratory scale. However the plant scale trial data was not in accordance with laboratory results and indicated inferior flotation performanceThe issue was studied and data based conclusions were drawn that the new generation collector aids faster and uncontrollable kinetics. A decision was taken for co-dosing of the synthetic and new collector for the second phase of the trial. A detailed laboratory analysis was done again and few dosing ratios that predicted optimum results were selected for plant trial. The dosing ratio was optimised as per flotation yield and product ashes during the plant trial. The results showed significant improvement from the first phase and optimum dosing rates were decided based on plant observations and data collection. The influence of various process indicators including water quality, feed and product ashes and process yield was studied during all the trials and promising results were established. The co-dosing of both the collectors conferred cost advantage and enabled to achieve superior performance."

Jan 1, 2016

By Charles J. Zablocki, Robert J. Kamilli

"Abstract - Buried, possibly mineralized granite cupolas at the Silsilah tin deposit in Saudi Arabia (lat. 26°06' N, long. 42°40' E) have been successfully located using a closely spaced electric-field-ratio profiling technique. In this study, electrical fields at 27 and 270 Hz across grounded electrodes spaced 50 m apart were measured along six traverses. This method is interpretable by inspection, unlike the dipole-dipole technique, which requires mathematical modeling for interpretation.In the study area, the technique allowed the authors to identify and distinguish among unroofed granite cupolas, cupolas with their aplite-pegmatite apical contact zones intact, strong (quartz-rich) and weak (relatively quartz-poor) greisens, dikes, faults, and pervasively argillized rocks.This method should be useful in the valuation of other shallow mineral prospects in similar settings in other parts of the world, especially deposits for which the location of vertical contrasts is important, such as veins or mineralized zones associated with the apexes of small igneous cupolas."

Jan 1, 1993

By M. K. Gangal, M. A. Stoakes, A. E. Hall

"The major features of the CANMET thermodynamic mine ventilation network program, developed by the Mining and Mineral Process Engineering Department of the University of British Columbia for the Canada Centre for Mineral and Energy Technology (CANMET), are described.The program is designed for use by deep Canadian mines in planning ventilation flows where the effects of auto-compression of air, moisture lift work and natural ventilation are significant. Routines to simulate stalled fans and give an optional cost printout have been included in the program.A supplementary plotting program used to simplify data interpretation is also described.The program is described with a test data example of a deep mine. It is a valuable analytical tool which can assist ventilation engineers to simulate many alternative ventilation strategies at a low cost in a very short time.IntroductionCanadian underground mines are becoming deeper and more extensive. The use of more and larger diesel-powered equipment increases the amount of air required to be circulated in these complex systems. These effects, coupled with the increasing unit cost of the energy required for mine ventilation, require that the air is used with maximum efficiency.Optimum airflow distribution can be obtained by using network computer programs enabling engineers to plan future ventilation systems based on quantitative assessments. The programs used for deep mines must make allowance for the change of air density with depth, as the assumption of incompressible flow leads to serious errors. Natural ventilation effects may vary with depth and from part to part of the mine; this must be catered for by the program. The air moisture content changes throughout the circuit and a significant portion of the fan work may be used in removing moisture from the mine; as this work varies directly with the flow, a suitable relationship must be utilized in the program."

Jan 1, 1982

By David Burchell

Duckbill mining is probably the simplest method of loading coal mechanically at the face in underground mines. It is a means of reducing the amount of physical labour required to produce a ton of coal. In effect, it is merely shaker conveyor mining brought up to date with the addition of a self-loading head or 'duckbill' on the end of the conveyor line. Any mechanical device used to load coal is a means of supplanting the human muscles as the medium for getting the coal off the floor into the transportation equipment. There can be no argument with the conclusion that a man can lift so much and no more. He can load more tons of coal on a low conveyor, because the lift is less, than he can in a pit car two, three, or even four feet high. Thus it follows that, if the lifting operation is entirely eliminated, the man should be able to produce even more coal. A mechanical operation is essentially a multiplication of physical strength. Although there are various ways in which coal can be loaded at the face by mechanical means, there is, perhaps, none more adaptable than shakers equipped with duckbills. This is particularly true for thin seams and in mines having heavy, tender top conditions which require close timbering. However, as we are discussing duckbill mining, we will make no further reference to any other type of equipment. The first, and to date the only, mine in eastern Canada to adopt a system of mechanical loading at the face is the Franklin mine of the Bras d'Or Coal Company, Ltd., at Bras d'Or, N.S. An experimental Goodman shaker conveyor with a self-loading head, or duckbill, was installed in this mine in 1940. Since that time other units have been placed in operation so that, today, this mine is completely mechanized. The method of operation 1s room-and-pillar. The operation is carried on in a 42-in. seam, which lies 420 feet beneath the Sydney Main or Harbour seam in the Sydney Mines basin. The slopes bear N.25 30'E., dip 10 per cent seaward, and are about 6,000 feet in length. The physical conditions of this seam do not make it particularly adaptable for complete mechanization as it contains a large amount of foreign material, such as clay intrusions or wash-outs and iron pyrites. These clay intrusions, known locally as 'troubles', vary in thickness from a few inches to as thick as eighteen feet and usually replace the coal to the full height of the seam.

Jan 1, 1947