Search Documents

By F. Y. Grepe

"THE MOST common type of mine hoist is, as is very well known, that in which the a.c. wound rotor motor is the driving medium. The reasons for the use of the wound rotor motor are, of course, economic. This type of equipment has, during the years, proved to be very reliable and reasonably satisfactory. It is, in fact, still being installed and in some places where a very hard and exacting duty cycle is demanded. As an example, a 600 h.p. 2,300-volt job was recently installed at the Caledonia mine (1) at Glace Bay. This is a vertical. hoist in a shaft only 175 feet deep but it is, nevertheless, working hard bringing coal to the surface and in making a trip at a speed somewhat better than every 20 seconds.The control equipment for such installations usually consists of a pair of primary reversing contactors which are interlocked both mechanically and electrically, together with some form of secondary controller. This, in the case of small hoists, can be a drum controller and metallic resistors or, in the case of larger hoists, a magnetic contactor panel and metallic resistors or, alternatively, can be one of the various forms of liquid rheostats which are available. The liquid rheostats, if of the dipper type, may be manually operated or it may be operated by some form of servo motor mechanism. In the weir type of liquid controller, the electrolite is, of course, pumped in and out of the rheostat."

Jan 1, 1954

By F. P. Hassani, Jacque Ouellet, M. Hossein

A laboratory investigation was undertaken to evaluate the effectiveness of different binding agents in a paste backfilling operation suitable to be used in a sulphide-rich environment. Different combinations of Portland cement and fly ash type C as well as ferrous slag were used as the binding agents. The unconfined compressive strength of the samples was measured for extended curing periods. The results indicate that the addition of 3% slag in the binding agent mix could produce strengths up to 0.5 MPa in the samples under investigation. For higher binding contents, the addition of Portland cement will lead to higher availability of calcium hydroxide and calcium aluminate, which are susceptible to deterioration from the phenomenon known as sulphate attack. Using slag, on the other hand, will reduce the permeability, availability of calcium hydroxide, and dilute the calcium aluminate ions reducing the susceptibility of the samples to sulphate attack. However, gypsum will form which could have the same detrimental effect on the strength of the treated matrix. Therefore, special attention must be given to the content and properties of agents used to activate the pozzolanic properties of the slag.

Jan 1, 2001

By L. E. Djingheuzian

ANON-CATARACTING (N-C) ball mill is so operated that the balls are not thrown in-ward at the top of their paths. The result is to maintain, in the mill, a quiescent pool in which classification will occur at a limiting size corresponding to the pulp density. N-C operation is produced by effecting proper relationship among mill speed, ball diameter, volume of ball load, and pulp density. Such operation is typified by the primary ball-mill operation of the Tennessee Copper Company, Copper-hill, Tenn., and the Cleveland Cliff Iron Company, near Ishpeming, Mich.

Jan 1, 1958

By J. B. Kitchin

"The design of conveyor belting for use in mines poses problems to the manufacturer that are unique. The challenge to be met is that of the production of a conveyor belt which can withstand use and misuse in an environment that may differ vastly from one country to another, and even between one mine and its neighbour.The development of a product to meet such varying requirements necessitates a protracted program of trials, both in the laboratory and in the field; a new successful development, the only criterion, can be said to have been achieved only after very long-term usage under actual, deliberately chosen, arduous mining conditions.New developments in conveyor belt construction can never stop, no more than can developments in new and advanced mining techniques. A new problem is set-an answer must be found. Some of the problems are noted here, and answered where possible, in what must after all be little more than an excursion into a very comprehensive and detailed subject."

Jan 1, 1967

By Angus W. Davis

The case of the P. G. E. railway is a peculiar one. Traversing, as it does, to a large extent, a mineralized country there are as yet no producing mines along its route although I am convinced that mines will be developed in the region tributary to the railway. The Fitzimmons group of claims, a copper property near Mons station, 37 miles from Squamish is now (unless recently relinquished) under bond to the Granby Company. On Cadwallader creek, in the upper Bridge river country, certain gold properties, referred to later, are being developed. Prospectors are fairly active in the Pemberton meadows area. There are also a large number in the Bridge river, Gun creek, and Whitewater districts. East of Marguerite station some development work is being prosecuted on some copper claims located there. In addition here and there throughout the entire route of the railway prospecting is being undertaken. At Hat creek, 15 miles from Pavilion station there is an enormous deposit of lignite. It is by no means certain that this coal can be profitably mined and hauled to the railway, but as a cheap fuel it offers possibilities in the recovery of by-products by destructive distillation. Logical procedure would ? indicate the expenditure of considerable money on development and, if results justify, the construction of a spur from the main line to the deposit.

Jan 1, 1925

"AbstractThe Sedimentary Basin area of Western Canada, which lies between the Precambrian Shield and the Cordilleran mountain area, covers approximately 800,000 square miles. Sediments ranging in age from Cambrian to Tertiary are present and, of these, horizons in the Upper and Lower Cretaceous, Jurassic, Mississippian, and Devonian have yielded commercial oil and gas flows. Producing horizons in the Cretaceous and Jurassic are sandstone, while all those of the Palaeozoic are carbonate rocks such as red limestone or dolomite (bioherms). Shows of oil and gas have been encountered also in the Cambrian and Triassic sediments.The broad structural features of this vast expanse of sedimentary rocks are the Moose Jaw syncline, the Sweet Grass-Battle River arch, the Alberta syncline, the Foothills belt, the Rocky and Mackenzie mountains, the Great Bear-Slave Lake basin, and the Mackenzie Delta Basin area.This contribution outlines the .stratigraphy and structure of the Basin area, and gives examples of present producing oilfield structures and stratigraphic traps.Part 1.-Regional StratigraphyIntroductionThe vast expanse of relatively undisturbed sedimentary rocks of western Canada has long been recognized as prospective territory to search for oil and/ or gas. This search in western Canada dates back before the turn of the century, but, considering the size of area to be explored and tested, the effort an<l money expended upon it, which, before the recent discovery of oil at Leduc, Alberta, appeared large and fruitless, now seems almost ridiculously small. A check-up of effort and money expended prior to and since the Leduc discovery would undoubtedly reveal that more wildcatting and development has taken place during the last two and a half years than during all previous years combined. The figures would astound not only the average citizen, but many within the industry itself."

Jan 1, 1950

By J. C. White

"During the early development of the Mattabi Mine in 1970, discussions with the Ontario Government revealed their policy of prohibiting, as much as possible, the development of new, isolated, single-industry townsites. Subsequently, Mattabi located its first housing in the Township of Ignace, which is situated 50 miles from the site of the mine and plant. Over 200 employees now commute 100 miles daily to and from work.This paper describes the experience gained and discusses the advantages and disadvantages of a remote townsite."

Jan 1, 1976

Cominco began investigations about ten years ago relative to noise abatement in underground operations. As a result of intensive research, this study has advanced so that the practice now has wide application. Automotive mufflers are used on vane-type blasthole diamond drills. Exhaust hoses are attached to longhole percussion drills. Hand-held drills, such as airlegs and stopers, are equipped with mufflers which are either part of the drill, as received from the manufacturer, or are light rubber de-vices developed, fabricated and installed by Cominco. Ear defenders are in general use. The paper reviews details of practices employed, and assesses the success achieved. Noise is generally associated with some of the basic equipment used in mining. About ten years ago, in order to improve on this situation. The Consolidated Mining and Smelting Company of Canada Limited began investigations relative to noise abatement in its underground operations. As a result of intensive research, this study has advanced to the point

Jan 1, 1964

By A. J. Paul Laprairie

The process for which it is to be used is too often the only consideration in the design of a vessel. A de-sign allowing for practical manufacture and erection, as well as for proper maintenance, can often give over-all economies. Most platework in-stalled today is of welded construction. Therefore, metallurgical control is important in its manufacture. Also, because many concentrating and re-fining processes tend to be corrosive, the subject of protective coatings as a part of the manufacturing process is extremely important. The plant de-signer should know how to evaluate and specify controls for the metallurgy and for the coatings. Mining operations are becoming more sophisticated in the field of mechanical engineering. More and more emphasis is being given to preventive maintenance. The first step in any maintenance program, however, is good inspection service. This paper will suggest methods for the inspection of platework, and outline methods for repair and replacement.

Jan 1, 1963

By Alan Bauer, Melvin A. Cook

Measured detonation pressures of "prills and oil" (94/6 ammonium nitrate/fuel oil) and three of the new "slurry" blasting agents are presented and compared with computed, ideal detonation pressures and with detonation pressures expected from the measured detonation velocities. Results seem to show that the peak pressure in the detonation wave in these cases is the Chapman-Jouguet pressure and that no "spike" exists in these detonation waves. The absence of the Zeldovich-von Neumann "spike" is noteworthy in view of the very long reaction zone lengths of these mixtures. The measured detonation pressure of one of the slurry blasting agents (DBA-3") under steel confinement ( 172 kilobars) is shown to be considerably greater than the ideal detonation pressure of 75 per cent gelatin dynamite (p. = 135 kilobars) despite the fact that the detonation was still somewhat non-ideal in "DBA-3," its computed ideal detonation pressure being 180 kb. The popular 94/b AN /FO blasting agent exhibited a detonation pressure of only 13.5 kb in 5" paper tubes, but 37.5 kb in 5"• steel pipe compared with a computed ideal pressure of 40 kb.

Jan 1, 1961

By P. Favreau

This paper describes the progress accomplished at the Noranda Technology Centre in the field of three-dimensional computer-aided underground blast design. Traditional methods of laying out underground blasts are reviewed, and the new computer-aided approach is described. Time savings achieved through the use of BLASTCAD can be advantageously used to better engineer blasts, using models and blast vibration analysis. Future work involving the attachment of blast models directly to the system is also addressed.

Feb 1, 1993

In April, 1961, a large pillar was removed by blasthole mining methods at Inco&apos;s Murray mine. More than half a million pounds of explosives were used to break 2,120,000 tons of ore in a single underground blast. The 5, 10 2-inch boreholes, involving 435,815 feet of drilling, were loaded over a three-week period, using conventional explosives and short-period electric caps. From this blast, more than half a million tons of ore have been removed to date (April, 1962) through slusher trenches situated in the footwall of the ore body. T HE Ontario Division of The International Nickel Company of Canada, Limited, operates six underground mines and two open pits in the Sudbury district in the north-central part of the Province. This paper describes the removal of a large pillar at the Murray mine (Figure 1), where 2,120,000 tons of ore were broken in a single underground blast by the blasthole mining method. This is the largest underground blast achieved to date (April, 1962) at Inco mines.

Jan 1, 1963

By O. E. Andrew

THE object of this paper is to present a brief summary of the dust control system in use on the 3,825-foot level at the jaw crusher station, Lake Shore mine. During the years 1936 and 1937, dust survey reports were presented to the management showing that high dust concentrations were being created during operating periods. At that time, however, this crusher was running only an hour or so each shift, and it was felt that no large capital expenditure for dust control equipment could be justified. In order to afford some protection to the operators, a number of respirators then on the market were .tested and the &apos;Comfo&apos; respirator was adopted for use by the crusher-men. In 1938 this crusher began to handle a large share of the total mine tonnage and the hours of operation were increased. Further dust sampling showed increased dustiness with the longer operating time. It was also realized that the operators suffered considerable inconvenience if they wore their respirators throughout the shift. If the respirators were not worn, then dangerous amounts of dust were being inhaled. The fact that the crusher station was situated on the 3,825-foot level limited the means that could be employed to eliminate the dust hazard. At that rime there was not available the 5,000 c.f.m. of fresh air which would be required to sweep out or dilute0 the dust, and there was also no way of disposing of the contaminated air without passing it on for other men to breathe. Thus it became apparent that a self-contained dust disposal system would have to be installed.

Jan 1, 1941

By W. J. Bennett

"I AM very happy to have this opportunity of speaking to the Montreal Branch of the Canadian Institute of Mining and Metallurgy.I have selected as the subject of my remarks transportation in that area which is at present our only source of uranium -Northwest Canada. Considering the widespread interest in atomic energy, the end-product of uranium, it may be wondered why I have not chosen to speak of a more spectacular aspect of the development. I hope it will be evident from what I have to say that transportation plays a very dominant role in our effort to maintain a continuing supply from Eldorado's producing property at Port Radium on Great Bear lake and from its coming producer at Beaver lodge Lake in Northwest Saskatchewan. Moreover, transportation has such a bearing on the entire mineral development of the Northwest that it cannot help but be of concern to an organization of this kind. Finally, the transportation problem, of which I shall try to tell you something, is quite unique and the story of its solution or partial solution is, I believe, an interesting one.Transportation experience on this continent indicates that the cheapest method of moving freight is still by water -with •rail, highway, and air transportation following, and in that order •of economic significance. Excluding rail transportation, since the area has as yet no railway lines, this order also applies in the Northwest. I shall direct my remarks to the two kinds of transportation which serve our uranium producers -water and air."

Jan 1, 1952

By Robert B. Parsons

"Investors in flow-through shares are going to need an expanded road map to find their way through a growing maze of tax rules affecting such shares. At the end of 1985, no fewer than three new sets of important tax amendments were tabled which could have a significant effect on flow-through share issues. This proposed legislation is discussed this month in Tax Notes.IntroductionIn a flurry of legislative activity at the end of 1985, the federal government tabled legislation which includes the introduction of new rules which will have a notable effect on investors in flow-through shares and on companies that issue such shares.First, on November 26, 1985, Bill C-84, the legislation to implement most of the changes announced in the May budget, was introduced in Parliament. This legislation includes the rules for the $500,000 capital gains exemption, a matter of considerable interest to flow through share investors.Next, on December 2, 1985, the government tabled a Notice of Ways and Means Motion which would extend the time horizon for spending flow-through share funds to include the 60-day period following the calendar year. But all news was not good news. On December 4 the government released its proposals for a minimum personal income tax, which would include rules that would catch an investor&apos;s CEE expenses and capital gains."

Jan 1, 1986

By E. J. Debicki

"At the 1992 PDAC Convention, Norman Keevil announced the formation of the Exploration Technology Division (ETD) of the Mining Industry Technology Council of Canada (MITEC). It was evident that base metal reserves in Canada were declining and that the cost of discovering a deposit in Canada was increasing. Coordinated research to develop new exploration technologies was required to discover the next generation of ore-bodies. The ETD was formed in response.The mission of the ETD is to contribute to the survival, profit, and growth of the Canadian mining industry by improving the efficiency and effectiveness of mineral exploration through development of innovative technology by man-aging and coordinating applied cooperative research. In addition, it is the intent of the ETD to become the principal agency by which cooperative research funds are transferred to researchers from the mining industry. The division is industry driven, industry funded and industry managed.The ETD’s Three-Year Plan has focussed80% of its research funds toward two objectives, improving the efficiency of exploration for VMS deposits and establishing the parameters necessary to discover the next Hemlo deposit. The remaining 20% is allocated to other projects, with the current emphasis on geophysics.In 1995, corporate members total twenty-three major mining companies accounting for90% of the exploration expenditures in Canada. The ETD is currently managing ten cooperative research projects totalling $4.6million. Other projects, estimated at $1.6 mil-lion, are currently under development."

Jan 1, 1996

By P. Favreau

"This paper describes the progress accomplished at the Noranda Technology Centre in the field of three-dimensional computer-aided underground blast design. Traditional methods of laying out underground blasts are reviewed, and the new computer-aided approach is described. Time savings achieved through the use of BLASTCAD can be advantageously used to better engineer blasts, using models and blast vibration analysis. Future work involving the attachment of blast models directly to the system is also addressed.IntroductionThe Noranda Technology Centre&apos;s (NTC) Environment and Mining Laboratory, in cooperation with the mining operations of the Noranda Group, is committed to the development and implementation of new technologies in the field of mineral extraction . Within the frame of its research program, the Blasting Technology Program is developing computer "" tools"" designed to assist the blasting engineer or technician. These computer "" tools"" are regrouped under a global software system called BLASTCAD.The BLASTCAD project started in 1990 at NTC. At that time computer programs designed to calculate and model various blasting parameters had been accumulated. These programs cam e from different sources and were mutually incompatible. Furthermore, they were developed as research programs with tittle effort spent on user interface. These programs are very useful, but are highly specialized, need large input files and can be quite tedious to use as ""standalone"" packages .Therefore, the situation being faced was one where all these programs were available at the Noranda Technology Centre, but not a t the operations. The two following options were then considered: 1. continue to run all the models and programs at the Noranda Technology Centre, and present results through reports to the mines, or2. regroup all the different programs under a single one that would make them share the same data base and be transported to the user. This second option is the one that was adopted; the result is BLASTCAD."

Jan 1, 1993

By Yvon Trudeau, Deni Raymond

"The Orion gold mine, located 7 Ian northeast of the town of Malartic, Quebec, was discovered in mid-1985. Underground exploration was undertaken in 1986 leading to commercial production in 1988. The upper part of the orebody was exploited above the 125 m level and a total of 131 090 t at an average grade of 5.31 g/t gold were extracted.This paper describes the authors&apos; current knowledge and interpretation of the geology, gold distribution, and structure of the Orion No.8 ore zone deposit. The deposit is an epigenetic lode gold occurrence somewhat unique in that both quartz-vein type and pyritic type of gold ore occur side-by-side. It is located within the Marban-Noriartic Deformation Corridor (MNDC) formed during a first deformation stage (D1) The MNDC is a well-defined regional structural feature in the Val d&apos;Or - Malartic mining camp. Primary gold mineralization is associated with the D1 event and is represented by pyritized, silicified and brecciated basaltic lavas enclosed by ultramafic flow units. The ore zone is concordant with the MNDC. Felsic intrusions are spatially related with the ore zone, but their role in the genesis of the ore has yet to be dermed.A second deformation event (D2) resulted in local folding, a second schistosity (S2) and reverse faulting. Gold remobilization, the formation of the gold-bearing quartz breccia and the emplacement of the main quartz vein at the No. 8 zone deposit were associated with this event."

Jan 1, 1992

By M. J. deBastiani

The uranium producing division of Denison Mines Limited operates a 6,000-ton-per-day integrated mining unit in the Algoma area of Ontario. The property is located approximately one and one-half miles from Highway I 08, eight miles north of the town of Elliot Lake. The property was staked in 1953, diamond-drilled in ?late 1954 and 1955, and put into production in 1957. Since that date, the operation has produced $250,000,000 worth of uranium oxide from approximately 11,000,000 tons of ore milled, and paid $18,000,000 in dividends to its shareholders. The operation employs about I000 people, and monthly operating costs are approximately one million dollars. From these figures alone, it is obvious that it was necessary to develop and institute an adequate set ?of controls for effective management at all levels of supervision over a period of four years, a system of production and cost control was developed that enables us to effectively measure the pulse of the various phases of the operation at any given time.

Jan 1, 1963

By Greg Baiden

Telerobotics focused on mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run? A new Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University. This chair will investigate these questions and many more through a series of experiments in a newly established telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian college?s eDome. The laboratory will support many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one/quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments and some preliminary results.

May 1, 2003