Search Documents

By Mauro Torres, Gabriel Zarate

"AngloAmerican used the extractant M5640 at Mantos Blancos and Mantoverde and uses PT5050MD at Los Bronces Division, which are aldoxime and modifier blends. In the first case, the modifier is the esther TXIB, while in the second case is the tridecanol TDA. It is a well-known fact that the extractant degrades while the modifier does not and with time the oxime/modifier ratio can change significantly, depending on the operating conditions of each plant.In order to evaluate the effect of this varying modifier content in the plant organic, especially in the organic losses, a complete metallurgical test work program was conducted at laboratory and pilot plant scale by Flomin SNF, a new extractant supplier. Results showed that the addition of an aldoxime without the modifier did not affect the chemical performance of the extractant, but there was a significant decrease in the viscosity and density of the organic.Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at the SX plants of Mantos Blancos and Mantoverde. In these tests, instead of adding extractant to maintain the organic inventory, CuPROMEX 3406 which is an unmodified aldoxime was added until the original oxime/modifier ratio was reached. This was obtained after 6 months of operation and since then both plants are running with the extractant CuPROMEX 3302 both supplied by Flomin SNF.In the case of Los Bronces, the pilot plant work was completed and it is programmed to run similar plant scale tests. In this case, the oxime/modifier ratio increased and TDA will be added until reaching the original ratio.The plant results obtained at Mantoverde and Mantos Blancos, together with the pilot plant test results obtained at Los Bronces, are discussed in this paper."

Jan 1, 2016

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By Riggin P. R.

"IntroductionIndustrial Relations combines two very important relationships - employee relations and union relations.Employee relations always come into play when people are hired to perform tasks. Because mineral processing plants cannot be operated successfully without people, at least not yet, if they ever will be, employee relations must exist in an operatingplant.If the employees choose to be represented by a union, then a relationship with the union as an institution also comes into play. It is very important to note that unionization does not mean that the employee relationship is replaced by a relationship with the union. The latter is superimposed on the former, but it does not replace it. Similarities and overlaps in the two relationships will be present, some of which are of fundamental importance. Nevertheless, they are two different relationships and the reader should bear this in mind when reviewing those parts of this chapter which discuss unionization, collective bargaining, collective agreements, and work stoppages.These two important relationships, which we have chosen to combine and call industrial relations, have crucial roles to play in the social system which interrelates people performing the necessary tasks involved in the operation and maintenance of a plant. The technological organization - equipment, process layout and so forth - and this social system are interdependent and complementary. This chapter attempts to show that the potential level of effectiveness of both the technological organization and the social system depends on the recognition and nurturing of this nexus between them.Occupational health and safety and training are subjects for another chapter. But, both of these have been critical and longstanding employee relations topics . They are destined to take on added importance in the future. As issues in collective bargaining, they are also attracting increasing attention in all union relations. It is hoped that the reader will not isolate from industrial relations those topics which are being dealt with in another chapter. They are very much a part of it and we cannot refrain from making some reference to them."

Jan 1, 1989

By R. S. Douglas

THE Granby Consolidated Mining, Smelting and Power Company, Limited, is engaged in the mining and concentrating of copper ores, and, incidentally, in the mining of coal and the production of electric power. The Company has been engaged in these various operations both on the mainland of British Columbia and on Vancouver island for the past forty-five years. This paper will attempt to cover their present operations in the Similkameen mining district of southern interior British Columbia. GENERAL CHARACTER OF THE DISTRICT The Interior Plateau in southern British Columbia ranges in elevation from 3,000 feet to 6,000 feet. In the vicinity of Princet0n, a depression in the Plateau forms a well defined basin which is floored with a series of nearly flat-lying Tertiary sediments containing some workable seams of lignite. From this basin, the upland surface rises gradually t0ward the south, from an elevation of 2,000 feet at Princet0n to 4,000 feet at Copper mountain, and 6,000 feet in the upper parts of the Similkameen basin, where it merges into the rugged and diversified t0pography of the Cascade system, with glacier inhabited peaks rising to over 9,000 feet. The valleys of Similkameen river and its tributaries are wide, having flaring sides and gentle slopes, and are separated one from another by subdued rounded spurs, of which Copper mountain is typical. The drainage of this district is taken care of by Similkameen river and its larger tributaries, such as Pasayten river, and Wolfe, Friday, and Whipsaw creeks. The name Copper mountain is applied to a gently arched, nearly flat-topped spur between the deep valley of Similkameen river to the west and the shallower valley of Wolfe creek tO the east. The mountain is appro-priately named from the number of copper deposits occurring on its sides and summit, some of which have been developed int0 an important producer, known as the Copper Mountain mine.

Jan 1, 1943

By U. Storck

"Shaft sinking for exploitation of the deep potash beds in Saskatchewan involved great difficulties from the very first because of the need to exclude from the shaft the high-pressure water encountered in the overburden. Control of the troublesome Blairmore quicksands was achieved relatively quickly by use of the freezing method and by lining with cast iron tubbing. The unsolved problem remained, however, of sealing the water-bearing Devonian where the formations had extremely low permeability and were thus hard to grout. Long experience in German potash mines had shown that the permanency of the whole mine would be seriously endangered if large amounts of unsaturated salt water were allowed to flow in from the shaft wall and merely removed by pumping. The prevention of water movement and the resulting dissolution of salt in the overburden were known to be most important. In the Alwinsal shaft, water flow from the Devonian has been prevented by the use of a steel and concrete sandwich lining similar in principle to a kind of lining introduced a few years earlier, and for another reason, in German coal shafts. As its installation is neither more expensive nor more time consuming than that of cast iron tubbing lining, this same lining was also chosen as protection against the Blairmore quicksands. The great advantage of the steel lining, in addition to its relatively high strength, is the fact that it is possible to make the joints of the individual segments absolutely and permanently water-tight by means of tested welds. The virtual dryness of the Alwinsal shaft will also result in lower costs because significant corrosion of all its steel installations, including skips, cage and ropes, will be prevented."

Jan 1, 1968

TRE ? worldwide leader in InSAR ? Spinoff of Polytechnic University of Milan ? Numerous patents for cutting edge technology (e.g. SqueeSAR?, PSInSAR?) ? Focus solely on InSAR with over 13 years experience ? ISO 9001 quality certification ? Powerful scalable parallel processor to handle all jobs What can InSAR provide for mining? An advanced suite of tools for monitoring ground deformation over mine sites: ? Deformation maps ? A dense network of measurement points ? Time series ? Cross sections of surface profile evolution

Aug 1, 2013

By J E. Curfman

This paper deals with using track-type and rubber-tired machines in the ripping and handling of overburden and ores. The techniques and proper attachments pertaining to the ripping of materials are covered in some detail. Production and relative costs of ripping, as against other methods, are covered in cases pertaining to the mining industry. The use of the refraction seismograph in predetermining the rippability of materials, including a chart relat-ing velocity to rippability, is covered. This operates on the principle that sound waves travel through subsurface materials at different velocities, depending upon the degree of consolidation of the material. It is known that the same factors that affect consolidation also affect rippability. Proper equipping of the tractor to insure maximum efficiency is also covered in some detail. Introduction T HE idea of loosening consolidated materials prior to further handling and processing is probably as old as man. The purpose of ripping is to provide fragmentation of rock and loosening of consolidated materials.

Jan 1, 1965

By L. M. Pidgeon

MAGNESIUM metal, with a specific gravity of 1.73, is two-thirds the weight of aluminium and one-quarter that of steel. It is the lightest metal which is stable in the atmosphere. Before the war it had begun, though somewhat slowly, to take a place among the established metals. In 1939, magnesium production on this continent amounted to some 3,000 tons per annum and was confined to one company. At that time, Germany produced perhaps 20,000 tons. The advent of war, however, increased the demand to fantastic heights and introduced production problems of unprecedented magnitude. By the end of 1943, North American production is expected to reach 300,000 tons per annum (1), an increase of one hundredfold. Such a rate of expansion has not been witnessed previously in the history of metallurgy. It has given the metallurgist an opportunity to try new production methods and to learn in a short time what might otherwise have taken many years. The metallurgy of magnesium is still in its formative years and at this time widely different production methods are in operation side by side. This paper will discuss these methods in so far as information is available for publication at this time. A general description of the new Canadian industry will be included.

Jan 1, 1944

By V. K. Srivastava1

Coal mine fires burn about 20?21 million tons of coal per year throughout the world, which not only results in loss of valuable coal reserves, but also cause serious environmental hazards over large areas. The famous Jharia Coalfield of Dhanbad, India is no exception; here a coal mine fire originally reported nearly a century ago is still continuing unabated in vast areas of the coalfield. In this paper, an attempt has been made to analyse high resolution multispectral thermal images of ASTER for mapping and delineating surface and subsurface coal mine fire areas of this coalfield. From the generated temperature gradient map, as well as from the surface temperature anomaly map, it has been possible to differentiate shallow and deep coal mine fire regions and other erroneous cultural features. It is observed that the coal fires are distributed mostly in the eastern part of the area, which has branched into two major coal fire zones: one along Lodna- Tisra-Bhulanbarari-Kujama-Jealgora Jharia and the other along the Kusunda-Kendudih area. The western fire zone is restricted in Dumra-Nadkhurkee-Jayramdih area. From ASTER thermal infrared data from 2006, the total affected area is estimated to be about 7 km2, of which the deep subsurface coal mine fire area is around 3 km2 and the shallow surface coal mine fire area is around 4 km2, as compared to 18 km2 coal mine fire area estimated in 1987 using Landsat TM thermal band data. In other words, the fireaffected region has decreased by about 50 % during the last 18 years. However, such decrease in coal fire area is seen in the central portion only, and has in fact increased in the south eastern parts of the Jharia coalfield. Study of Differential Interferometery images, generated from Earth Resources Satellite (ERS) synthetic aperture radar (SAR) tandem data has shown that the active coal mine fires are in general associated with low topography/subsidence areas.

Aug 1, 2013

By Andrew Artzer, Michael Moats, Jack Bender

Antimony and bismuth in copper electrorefining electrolytes can cause cathode contamination, leading to the careful control of their concentrations. This study examined the laboratory scale removal of bismuth and antimony from an electrorefining electrolyte using a solvent extraction mini-pilot plant. The ability of a proprietary phosphonic acid ester extractant (REX-2) in a commercial diluent was studied in a simulated commercial setting. Antimony and bismuth were both extracted effectively from the electrolyte (72% Bi and 70% Sb removed) and Bi was effectively stripped (92% Bi recovered) with 400 g/L sulfuric acid. A final strip solution was obtained from the SX circuit containing 0.36 g/L Bi, 0.043 g/L Sb, 1.3 g/L Cu, and 0.18 g/L As. Unfortunately, most of the extracted Sb remained in the organic phase. Following the pilot study, experiments were performed to examine the precipitation of bismuth from the aqueous strip phase and the removal of antimony loaded on to REX-2. INTRODUCTION For many years, antimony and bismuth have been some of the most problematic impurities in copper electrorefining (ER) (Bardwell & Lapee, 1933). Along with surface roughening, high concentrations of Sb and Bi can contaminate the copper cathode and precipitate at the copper grain boundaries. This drastically reduces the drawing ability of the metal (Bender & Emmerich, 2016). For these reasons, it is necessary to control Sb and Bi concentration in the cathode, which is done by controlling their concentration in the electrolyte. Conventionally, Sb and Bi concentrations are controlled by maintaining a proper As/(Sb+Bi) molar ratio in the anode and arsenic concentration in the electrolyte. Antimony and bismuth are removed during electrolyte purification using liberators (electrowinning cells) and/or ion exchange. Liberators treat an electrolyte bleed stream from the ER circuit and electrodeposit increasingly impure copper as the copper concentration of the solution decreases. Traditionally, first stage liberators reduce the copper concentration from ~45 g/L to ~15 g/L and produce saleable copper. Second stage liberators decrease the copper concentration to ~8 g/L (Biswas & Davenport, 1980) which results in contaminated cathode that is returned to anode production (Biswas & Davenport, 1980; Wang, 2004). Further electrolyte purification is not always required but third stage liberators can be used to reduce copper concentration below 2 g/L which results in significant removal of As, Sb and Bi and very impure deposits which are recycled to a smelter or used for As production. However, liberators do not have very high energy efficiency (Acharya, 2014; Ando & Tsuchida, 1997) and below 0.5 g/L copper, highly toxic arsine gas may form (Biswas & Davenport, 1980).

Jan 1, 2019

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By Lise-Aurore Lapalme

Structure of the Presentation ? sustainable development and its social dimension ? challenges that mining is facing ? responses by industry ? corporate social responsibility ? the role of government Sustainable Development ? new perspective on how we view development ? consider how minerals and metals contributes to sustainable development ? challenge to better understand economic, environmental and social aspects ? make social aspects more broadly understood and appreciated

May 1, 2002

By Fan Delian, Ye Jie, Lui Tiebing

The lower and the upper parts of the Doushantuo Fonnation, Hubei Province, China, contain silicate-type K-rich beds (illite and feldspar), and intraclastic phosphorites, as well as Ag-V and V deposits in a "Black Shale Series". The K-rich beds fonned in an anoxic basin whereas the phosphorites fonned in a more oxic and higher energy depositional environment. The Black Shale Series occurs in the lower and upper parts of the Doushantuo Fonnation; that in the upper part consists of black illite shale and dark gray dolostone, and contains Se-rich Ag and V deposits. These deposits are of more industrial significance than the previously discovered Ni-Mo polyelement sulfide deposits which occur in the Lower Cambrian Black Shales Series of South China. Studies of lithotype, sedimentary sequence, and geochemistry of the Doushantuo Fonnation have led to more attention being focused on the uppennost Black Shale Series and its Ag-V and V deposits. There are three ore types: black, Ag-V-rich, illite shale; black, V-rich, illite shale; and dark gray, Ag-Vrich, fmely crystalline dolostone. The first two ore types contain 3070 to 5% Corg and the last, 1.25%. The Ag-bearing minerals are naumannite, argyrodite, aguilarite, acanthite, and native silver that occur as inclusions in pyrite associated with barite. Vanadium substitutes for AI in illite and is also related to organic-matter contents. Because (1) the pre-Sinian Kongling Group contains one to three times greater than the Clark Ag value; (2) black, illite shale has a negative Ce anomaly; and (3) there are large occurrences of black, K-rich, tuffaceous, fme siltstone, the sources of Ag are thought to include subaerial and submarine volcanic materials. It is proposed that Ag, V, and Se were absorbed by clay particles and organic matter during syngenetic deposition in an anoxic environment; Ag subsequently was reconcentrated into sulfides and selenides, whereas V was incorporated structurally into illite during early and late diagenesis. These types of Black Shale Series-hosted Ag-V and V deposits are, therefore, considered to be sedimentary-diagenetic in origin.

Jan 1, 1992

By Himanshu Dehra

The pre-fabricated outdoor rooms are often utilised near the mines and construction sites for office purposes. The paper has presented modelling and simulation results of the integration of commercially available glass coated photovoltaic (PV) energy technology and solar ventilation technology into a pre-fabricated outdoor room. The pre-fabricated outdoor room has been setup at Concordia University, Montréal for full scale testing of the glass coated PV modules with solar air ventilation. The computer simulation model has been developed for PV modules installed on a double wall wooden frame in an outdoor room based on its preliminary field testing. The testing apparatus was a wooden frame assembly of double wall with solar air ventilation: two adjacent glass coated PV modules, air column and plywood board filled with polystyrene. The measurement data collected from various sensors were: solar intensity, ambient air temperature, room air temperature, electric power, surface temperatures of PV modules and plywood board, air velocities and air temperatures in the air column. The enhancement in the air velocity of the air column was achieved with an exhaust fan fixed in an outdoor room. The simulation model is used to perform the two dimensional energy analyses with applied one dimensional solution of steady state heat conduction equations. The simulation model is based on conjugate heat exchange paths with network boundary conditions of convection, radiation heat exchange and solar air ventilation heat transport. The model parameters are based on measured values of ambient air temperature, room air temperature, air velocity at outlet of air column in double wall, electric power and available solar intensity. The model has predicted fairly well energy performance of glass coated PV modules with solar air ventilation installed on a wooden frame. The model is also useful for predicting heating, ventilating and air-conditioning (HVAC) requirements for the pre-fabricated outdoor rooms.

May 1, 2007

By M. A. Creaney

"The Construction Group is responsible for the construction of all of Placer Dome’s major projects and contributes to the development of most major feasibility studies. This group includes an international collection of Placer Dome people who have built mines in Papua New Guinea, Australia, Chile, the United States and Canada. This paper outlines the changing role of the Construction Group from the early days of single projects to today, when several projects are in various phases from feasibility to construction. The projects’ total annual budgets have from time to time exceeded one billion dollars. IntroductionAs the competition increases globally between the major gold mining companies, the impetus continues to build mines at the lowest cost with the shortest construction schedule. Placer Dome has more than met that challenge by building mines around the world at a pace that was not contemplated 15 or 20 years ago. Since 1960, Placer Dome has built 30 mines and expansions at a cost of nearly 4.5 billion dollars.In the last six years alone, Placer Dome has built 14 mines and expansions, worth 2.6 billion dollars. The company’s success is due primarily to Experience, Innovation, People and Standards.The diversity between projects, let alone the pace, has been a challenge. Placer Dome has built mines around the world in a variety of extreme climates and distinctive cultures. The construction experience gained from these projects has allowed Placer Dome to develop an extensive knowledge and data base making it easier to “fast track” projects.Through the years Placer Dome has developed a human resource base. It now has an experienced and adaptable core team of people able to set up construction projects and build mines anywhere in the world. By developing standards and systems to support the projects they can act as soon as a new project is approved, and complete the projects quickly and effectively. The result is that Placer Dome now has the construction expertise to build its own mines, giving them the competitive advantage that allows them to design and construct a mine in the least time at the lowest capital cost. This was demonstrated in March 1997 with the completion of the construction of two new mines in 12 months."

Jan 1, 1998

By G. Frithum

In the present paper a new and highly economic route for Fe-separation from HCl leaching processes in hydrometallurgical applications is described. In most ore leaching processes, Fe is involved and needs to be separated; HCl has become an interesting leaching agent, because it can be recycled. Usually a mix of Fe2+ and Fe3+ is obtained which can be hydrolyzed directly (in case only Fe3+) or roasted via pyrohydrolysis (in case of Fe2+) to ferric oxide. Economic oxidation of Fe2+ to Fe3+ is described, and potential technologies for regeneration of HCl with separation of Fe are shown and compared.

Jan 1, 2014

By J. R. Goode

"Canada developed pioneering rare earth solvent extraction methods to recover the rare earths and thorium as by-products of uranium recovery operations in Elliot Lake, Ontario, and was a major supplier of these key elements from about 1960 until 1990. At one stage, Elliot Lake was supplying perhaps one third of the world’s yttrium as well as much of its thorium. This paper reviews the development of Canada’s early rare earth and thorium production facilities. INTRODUCTIONThe rare earths and thorium were first identified in the early 19th century but were little more than curiosities for the next century. However, in the mid-1960s the invention of rare earth-based phosphors for the cathode ray picture tube used in colour television sets launched a major demand for certain rare earths.The use of thorium as an alloying agent in aircraft and missiles grew rapidly in the late 1950s. In the same period, demand for uranium for both weapons and power production soared. Also in the late 1950s, the Elliot Lake uranium-thorium-rare earth deposits (also known as the Blind River deposits) were discovered. This conjugation of events led to uranium production in the Elliot Lake camp, quickly followed by the co-production of thorium and, later, the rare earths.Uranium production in the Elliot Lake camp continued from 1955 to 1996. Thorium was produced continuously from 1959 to 1969. Rare earths were produced, intermittently, from 1965 to 1990. Complete production records are not readily available but unquestionably Elliot Lake made a significant contribution to world thorium and the rare earth production. This paper, presented earlier in an abbreviated form (Goode, 2012), is intended to present as much of the information that is available."

Jan 1, 2012

By A. O. Sfriso

"Numerical modelling is becoming universal in rock engineering practice. Most applications focus on the prediction of failure loads of 2D problems, where the numerical models are useful extensions to analytical methods and experience-based design criteria. For 3D problems and problems where the assessment of serviceability indicators – displacements, ground-structure response, etc. – are of importance, the selection of the constitutive models themselves and the implications of the selection of material parameters may have a very heavy impact on the reliability of the model outcome and its predictive capability.This paper overviews basic common aspects of constitutive equations used in practical rock engineering and summarizes some challenges that are frequently observed when reviewing numerical models performed for routine problems in rock engineering. INTRODUCTIONNumerical methodsFrom a philosophical perspective models, either analytical or numerical, are idealizations of a perceived reality. For us engineers, models are just tools we use to guide our judgement and understanding of the problem in hand. When dealing with problems in rock engineering, we resort to a wide range of techniques:1. Closed form solutions like confinement-convergence methods for circular tunnels: these methods satisfy equilibrium and compatibility requirements at the cost of a crude simplification of the material behavior and geometry;2. Limit analysis methods, like bearing capacity formulas: lower bound methods satisfy equilibrium but sacrifice compatibility, and upper bound methods do the opposite. Material behavior must be simple, geometry admits limited freedom;3. Limit equilibrium methods, like method of slices for slope stability: they satisfy restricted forms of equilibrium, do not satisfy compatibility requirements, require simple material behavior but have a much greater flexibility on geometry;4. Numerical methods, where a mesh is employed to discretize the problem geometry: when properly formulated, these methods satisfy equilibrium and compatibility requirements and give reasonable approximations to the behavior of very complex geometries and construction sequences. Very little restrictions remain on geometry and material behavior, but the cost of calibrating the material parameters can be very high."

Jan 1, 2015

By Ryan L. Veenstra

This paper presents a modelling study of a cemented paste backfill in an underground stope. The model was developed to help provide a better understanding of what is happening in the stope during the filling stage of the stope. In order to do this, the model incorporates the paste rise rate, stope geometry, and time-dependent input parameters. This paper looks at the effect of geometry in two parts. The first part compares a series of simple rectangular stope models. These models differ in size both in two and three dimensions. The second part compares the results of four 2D models together and then to the field instrumentation data. Part of this section introduces the geometry and instrumentation within the test stope.

Jun 1, 2012

By Dave Shook

A Mineral Processing facility in Montreal has recently implemented a leading-edge intranet solution for monitoring the performance of plant operations, and providing condition-based maintenance. This innovative multi-faceted software implementation incorporates: web-delivered plant information systems; area-wide control loop performance assessment (using sophisticated algorithms to evaluate poorly performing controllers); and integrated alarm management functions. The system has enabled a project to improve plant operations through better process control. Maintenance technicians, engineers, supervisors and managers all can see the performance of the controllers, and the performance of the plant itself, through webdelivered graphics and reports. Information is combined from many sources, real-time, historical, relational and analytical, to provide a complete picture of plant operation. The web-based solution centralizes the administration of user access, and simplifies the deployment of several different kinds of information to many desktops. It is an extensible system that allows users to create and share their own web pages and data views. The paper will discuss the solution architecture and the improvements the I.T., operations, maintenance, and engineering groups have experienced, and overall benefits to the facility.

May 1, 2002