Search Documents

By H. G. Stephenson, C. W. Gregory

"This article describes the methods used for pillar extraction in the Wilson Seam at Canmore Mines, Alberta. The Wilson Seam is extremely gassy and varies in thickness between 7 and 30 ft, with an average of 12 ft. The gradient varies from 5 to 30 degrees, with an average of 15 degrees. The seam was developed using Lee Norse miners to form pillars which the company intended to extract using the same machines. Before pillar extraction commenced, an abandoned and inaccessible mine 160 ft above the Wilson had to be drained of 360 million gallons of water. When this was done pillar extraction commenced. Conditions in the mine slowly deteriorated and after 6 months the decision to withdraw the continuous miners was taken. Slusher hoists were installed to replace the continuous miners, with the result that roof conditions and safety steadily improved."

Jan 1, 1972

By W. B. Coker

A helicopter-mounted lake-sediment and lake-water survey was carried out over Grenville rooks in the Renfrew area (parts of Renfrew and Lanark counties) during four days of October, 1975. In the course of this survey. 1150 square kilometers were covered, with 246 lake-sediment and 276 lake -water samples collected from every body of water on which the helicopter could land. Sample sites, which averaged one per 4.6 square kilometers, included lakes, ponds, beaver ponds, swamps and marshes. Lake-sediment samples were taken using a G.S.C. sampler. Waters were collected directly into polyethylene bottles. At each sample site , surface and bottom-water pH, dissolved oxygen content, conductivity and temperature were measured using a Martel. Water Quality Analyzer. The lake sediments were air dried and then ball milled to pass a minus 80-mesh sieve. Lake sediments were analyzed for U by delayed neutron activation and for Mo, Cu, Zn, Pb, Fe, Mn, Ni and Co by atomic absorption techniques. The organic content of the sediments was determined by loss on ignition at 450 °C. Lake waters were acidified with nitric acid on the day of collection. The U content of the water s was determined by fluorometry; the Cu, Zn, Pb, Fe, Mn , Ni and Co contents of the waters were determined by solvent extraction - atomic absorption techniques. A close relationship was found between bodies of granitic, syenitic and pegmatitic bedrock and elevated U levels in the lake sediments. The Hurd Lake and White Lake granitic intrusive were encompassed by an annulus of higher U activity. Field inspection revealed that the U concentrations occur within a zone which may represent a contact metamorphic aureole. Within these complexes, anomalous concentrations of U appear to be associated with Mo. Information derived from the lake-water data reinforces the geochemical distributions outlined by the lake-sediment survey . This survey was carried out in order to develop optimum sampling and analytical procedures for geochemical reconnaissance of the Grenville Province that may be carried out under the auspices of the Uranium Reconnaissance Program.

Jan 1, 1977

By A. F. Brock

Introduction During the past ten years, shaft sinking has been going on continuously at Inco and new shafts and shaft extensions have been sunk under a broad diversity of conditions. The Murray mine and the Stobie section of the Frood-Stobie mine have?been opened and a main hoisting and supply shaft has been sunk at each of these mines; No. 2 shaft at Murray was sunk initially from surface to 1,960 feet and is now being extended; No. 7 shaft at Stobie was sunk from surface to 3,105 feet. No. 2 shaft at Garson has been extended from 2,200 feet to 3,200 feet in depth. At Levack, No. 2 shaft is being extended from 1,860 feet to 2,850 feet for ore hoisting from the 2,650 lev el. At Creighton, No. 6 shaft, collared on 52 level, was sunk 1,740 feet to a total depth of 5,563 feet below surface. It is the deepest Inco working. At Creighton, also, No. 7 shaft is being sunk from surface to the 30 level to handle the ore from caving operations. Ail Inco main hoisting and supply shafts sunk during the past twenty years have been vertical rectangular shafts equipped with two cages and two ore skips. The cages are standard and interchangeable for all shafts except Garson No. 2; they are single-deck, 13 ft. 4 in. by 5 ft. 2 in. inside and are designed to carry a maximum material load of 16,000 lb. The man load is 48 men. Skip capacities at the several shafts vary from 8 to 15 tons. Forty-two hundred feet bas been established as the standard vertical lift, and the permanent hoisting equipment at each shaft is designed for eventual hoisting from that depth.

Jan 1, 1950

By K. Liu

"In the present work, two-step heat treatments with preheating treatments at different temperatures (175, 250 and 330°C) as the first step followed by the peak precipitation treatment (375°C/48h) as the second step have been performed in Al-Mn-Mg 3004 alloys to study their effects on the formation of dispersoids and evolution of elevated-temperature strength and creep resistance. During the two-step heat treatments, the microhardness is gradually increasing with increasing time until to a plateau after 24 hours when first-treated at 250°C and 330°C while there is a minor decrease with time at 175°C. Results show that both the yield strength and creep resistance at 300°C reach the peak values after the two-step treatment of 250°C/24h+375°C/48h. The formation of dispersoids is greatly related to the type and size of pre-existing Mg2Si precipitated during the preheating treatments, in which that coarsened rod-like ß’-Mg2Si strongly promotes the nucleation of dispersoids while finer needle-like ß’’-Mg2Si has less influence. Under optimized two-step heat treatments and modified alloying elements, the yield strength at 300°C can reach as high as 97 MPa with the minimum creep rate of 2.2×10-9 s-1 at 300°C in Al-Mn-Mg 3004 alloys, enabling them as one promising candidate in lightweight aluminum alloys for elevated-temperature applications.INTRODUCTION Due to the rapid demand from weight-sensitive automotive and aerospace industrials for the light alloys, such as aluminum alloy on the elevated-temperature applications, Al-Mn 3xxx alloys has been developed to obtain the good properties at both room temperature (RT) and elevated temperature, in which the dispersoid-strengthening mechanism plays a significant role (Li & Arnberg, 2003; Li, Muggerud, Olsen & Furu, 2012; Liu & Chen, 2015, 2015). In our previous works (Liu & Chen, 2015, 2015; Liu, Ma & Chen, 2017), the yield strength and creep resistance at 300°C of Al-Mn-Mg 3004 alloy were further improved by modifying the alloying elements, such as Fe and Mo, to optimize the characters of dispersoids, including the size, distribution and the dispersoids free zone (DFZ). For instance, Mo was introduced in aluminum alloy to further improve the volume fraction of dispersoids and reduce the area of DFZ, leading to increasing on both the strength and creep resistance at 300°C (Liu, Ma & Chen, 2017). On the other hand, the mechanical properties became worse at higher Fe content due to its consumption more Mn to form Al6(MnFe) intermetallics, resulting in less available soluted Mn for the precipitation of dispersoids (Liu & Chen, 2015). Therefore, optimizing the characters of dispersoids is always the key to improve the elevated-temperature properties of dispersoid-strengthened aluminum alloys for elevated-temperature applications."

Jan 1, 2017

By T. L. McCall

A short description of mining practice in the Sydney coal field in general is followed by a discussion of the operations in the No. 12 colliery of the Dominion Coal Company, Limited, as being typical of the trend in operating methods obtaining throughout the field. Development of longwall mining to the present system of three walls in line is outlined, together with a summary of the cycle of operations involved in systematic operation.

Jan 1, 1944

During the past decade, the miner-al industries have been faced with an increasing shortage of engineers. The point has now been reached where the shortage may be termed critical. This shortage may be attributed directly to declining enrollment in the mineral science programs offered by the universities on this continent. Although the reasons for declining enrollment are undoubtedly many, two major hypotheses may be postulated. The first is that high-school graduates are either unaware of the mineral industries and the opportunities in them or that they are aware of them but have somehow obtained a false image of their true nature. The second is that they are aware of the true nature of these industries and the opportunities they offer but find them exceedingly unattractive. The problem of dwindling enrollments has, in recent years, been subjected to a concerted attack by the industries and professions concerned. However, their efforts to date have been based essentially on the first hypothesis. Sufficient results are now available to suggest that either the methods of attack are inappropriate

Jan 1, 1965

By C. R. Ross

"THE ASSESSMENT of pneumoconiosis-producing dusts in mines and other industries is usually undertaken for one or more of three reasons: (1) To compare dust exposures at particular operations with standards of permissible dustiness in order that hazards may be evaluated and preventive procedures initiated where required.(2) To study particular operations with the objective of improving dust control devices or procedures by locating dust sources. (3) To obtain data which, along with the results of medical investigations, may assist in understanding the causes of dust-induced diseases or aid in the establishment of permissible standards of dustiness. Most dust measurements are made for the first of these reasons -to evaluate dust hazards so that they may be controlled. For this purpose, four quite different assessment techniques have been in widespread use for many years. One of these is based on the konimeter, an instrument familiar to most .Canadian mining men; a second on the impinger, which is also widely used in Canada, and almost exclusively so in the United States; a third on the thermal precipitator, used extensively in Britain and South Africa; and a fourth on the tyndallometer, a light-scattering instrument used in Germany."

Jan 1, 1960

By M. A. Gomez, V. Yahorava, J. A. Strauss

"It is accepted widely that pressure oxidation (POX) is the most appropriate technology for processing of arsenic containing refractory gold ores. However, studies on the stability of various iron-arsenic precipitates formed during POX are limited. Since the behaviour of these phases could have significant practical implications for gold processing plants, it is important to study them in isolation. This paper compares two synthetic precipitates, basic ferric arsenate sulphate (BFAS) and basic ferric sulphate (BFS) in terms of their formation, behaviour during hot curing and cyanidation, as well as their environmental stability. BFS and BFAS were synthesised hydrothermally at 205°C and their mineralogy was confirmed using various techniques. During synthesis, the addition of H3AsO4 into an aqueous Fe2(SO4)3-H2SO4 mixture significantly decreased the iron yield to BFAS in comparison to BFS under equimolar initial iron and acid concentrations. The BFAS dissolution kinetics was slightly faster, as compared to BFS, during subsequent hot curing. Cyanidation test work on the washed synthetic precipitates indicated that the lime consumption of BFAS was three times lower in comparison to BFS, while cyanide consumptions were comparable. Fresh BFS and BFAS precipitates, as well as their cyanidation residues, were found to pass the respective environmental tests in terms of arsenic release.INTRODUCTION Pressure oxidation (POX) is generally viewed as the most appropriate technology for the processing of arsenic-containing refractory gold ores due to the stabilisation of arsenic in the leach residue (Dutrizac & Jambor, 2007; Gomez et al., 2008; Harris, 2003; Collins, Berezowsky, & Weir, 1988). Detailed laboratory studies indicated that several Fe(III)-arsenate type compounds may be formed under typical conditions of autoclave treatment of refractory gold ores (Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2010; Gomez, Becze, Cutler, & Demopoulos, 2011). The basic ferric arsenate sulphate (BFAS) phase (Gomez et al., 2008), also known as Type II ferric arsenate (Swash & Monhemius, 1994) or Phase 3 (Dutrizac & Jambor, 2007), is one of the most common arsenic-bearing products (Harris, 2003; Dutrizac & Jambor, 2007). BFAS precipitation is viewed as one of the best routes for arsenic stabilisation and performed equally well to scorodite during environmental stability tests (Harris, 2003; Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2011)."

Jan 1, 2017

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By B. W. Clyburn

"Coals from the Corporation's Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing all essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.Introduction Very high fluidity and unusually low ash are the outstanding characteristics of coal from Devco's mines in the Harbour seam of the Sydney coal field. However, sulphur content, mainly pyritic, ranges from 1 to 2.50Jo. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required. Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs. Typical data on the various coal properties of importance in the production of coke are included in Table 1."

Jan 1, 1985

By Richard J. Wardle, Ambrose F. Howse

The industrial minerals industry in Newfoundland and Labrador is a significant contributor to the provincial economy. The variety ofcommodities produced reflects the diverse geological environment from which they come. A highlight of the past decade has been the continuing development of dimension stone quarries, with producers now active in anorthosite, gabbro, granite and sandstone. Other dimension stone prospects have been identified and are in various stages of assessment and development. Western Newfoundland hosts a large resource of limestone, dolomite and marble. It provides raw material for industries that produce Portland cement, agricultural limestone and aggregate, as well as chemical-grade limestone and dolomite products. In western Labrador, dolomitic marble is quarried for use in the production of self-fluxing iron ore pellets. The recent opening of a new gypsum quarry at Fischells Brook signalled the beginning of a new era in the commercial production ofgypsum, a commodity which the province has produced since the 1950s. Hopefully it will emulate the nearby Flat Bay Quarry (now closed) which was a long-time exporter to markets along the U.S. eastern seaboard, in addition to supplying local demands. Oil production and continuing exploration in the Newfoundland offshore has renewed interest in local barite deposits for potential use in drilling fluids. Already there has been some production from the Collier Point deposit, and at Buchans, an existing plant is being refurbished to recover barite from a large tailings pond. Emerging new industries include the development of an antimony mine in central Newfoundland, the development of silica deposits near Labrador City for silicon metal production, and reactivation of the St. Lawrence fluorspar mine. The province has many deposits with development potential such as rare metals at Strange Lake, white marble at Roddickton and salt deposits near St. George's Bay region.

Jan 1, 2001

By M. S. Badollet, N. W. Edgerton

"A study of the physical properties of long grades of asbestos fibers imported into the United States during the past eight years has disclosed information that will contribute materially to effective selection and use of fibers for electrical products. The study embraced fiber lengths, volume resistivity under three different conditions, total iron by chemical analysis, magnetic rating, conductivity of an aqueous ex-tract and its sodium chloride equivalent.The fibers examined included chrysotiles from Rhodesia, British Columbia, and Barberton area; marlime from Bechuanaland and Province of Quebec; amosite and crocidolites from Africa and Australia; and anthophyllites from Mozambique and from Georgia in the United States. Volume resistivity values provide a relative basis for estimating the electrical performance of end products; magnetic rating -an estimate of the quantity of iron compounds present in excess of those in the asbestos structure; conductivity of an aqueous extract; and an estimate of the ionizable impurities in fibers.Tests of these factors yield in-formation, not heretofore generally known, which may serve as a guide in the evaluation of asbestos fibers for electrical products."

Jan 1, 1960

By A. A. McDonald

Anode casting has been in operation for two years in Hudson Bay Mining and Smelting's Flin Flon smelter. The new plant allows all casting to be done on one shift and so achieves considerable labour savings. The equipment and operations are described. Some important features are as follows: very consistent anode weights by the use of the load-cell controlled casting ladle; excellent mould life ; very low reject rate; and trouble-free take -off tower. Some of the start-up problems are described and an outline is given of the main operator functions. Data on labour, propane and maintenance costs are presented.

Jan 1, 1977

By Ian Hattie, Mark R. Wilson, T. Kurtis Kyser, Brian W. Janser

Petrographic, chemical and isotopic compo itions of auriferous and non-auriferous quartz vei ns from the Sta r Lake and Flin Flin-Amisk Lake areas of northern Saskatchewan indicate diver e origins fo r the fluids associated with gold mineralization. In the Sta r Lake area, the metavolcanic , Star Lake pl uton, and heared mafic dikes have retained their original igneous 81 80 values. The 81 80 value of quartz from mi neralized veins vary by I per mi! and range from+I0 to+IJ. The only quartz ample having a 81 80 value outside th is range came from a vein not associated wi th a dike or gold mineralization . Quartz from the Star Lake pluton has identical 8180 value to the qua rtz from mi neralized vei ns which suggests that the vei ns and the pluton are related to imilar proces es. The diffe rence in 81 80 values between mi neralized and barren vein may erve a a potential exploration tool in this area. Because o34S val ues of a limi ted number of amples of pyrite from gold-bearing quartz vei ns at Star Lake correlate directly with gold content. the gold may have been syngenetic with the su lphur and the 834 value may be useful for exploration . 8180 values of co-existing quartz, calcite, and amphibole in the veins from Star Lake indicate that isotopic disequilibrium among the minerals is common, but the val ues also record a high temperature of formation (ea . 500°C) involvi ng a component of magmatic fl uid. TheoD value of hydrou mineral from Star Lake retain their original igneous values but whole rock values are generally much lower, an effect attributed to interaction of the minerals with a late meteoric water. In the Fl in Flin-Amisk Lake area, auriferou and barren quartz veins formed from a mixture of hydrothermal and metamorph ic flu id at lower temperatures (ea . 350°C) than those at Sta r Lake. Becau e there i no apparent correlation between 8180 values of the quartz with gold content or relative age of the vein , nor between the 834S val ues of pyrite and gold content, table isotopes appear limited as an exploration tool in the Fl in FlonAmisk Lake areas.

Jan 1, 1986

By Marie-Eve Boucher

The slag in iron ore pellets allows wet sintering during firing and leads to suitable bounding. The process of slag formation differs whether it takes place in the core or in the external zone of a pellet. In the core, hematite can be reduced to secondary hematite, depending on the temperature and on the carbon monoxide/dioxide partial pressure ratio. The reaction rim that appears at the outskirts of a silica particle in contact with the FeO bearing magnetite is considered as the slag precursor in the core of the pellet. By contrast, in the external zone of a pellet, where O2 is available and CO partial pressure is very low, the first step towards slag formation is flux decomposition, mainly dolomite and limestone. The CaO liberated through this reaction will be available to react with hematite by solid diffusion to form calcioferrites, which play an active part in the slag evolution process. These two slag formation paths will be explained.

May 1, 2007

By D. W. Davis, P. Landais, L. J. Robb

Abstract -Nodules of carbonaceous matter have been observed in several Archaean peraluminous granites adjoining the gold- and uranium-bearing Witwatersrand Basin. These nodules, which resemble solid bitumen, usually replace uraninite or uranothorite and are paragenetically late. They show many similarities to kerogen seams and nodules associated with the conglomerate horizons in the Witwatersrand Basin, including composition, maturation, intimate association with uraninite, and a late paragenesis. U-Pb isotope ratios for granite-hosted and Witwatersrand kerogens define a single, albeit somewhat diffuse, Pb-loss discordia suggesting an upper intercept age of circa 2300 Ma. Carbon isotope analysis indicates lighter ?13C values for the granite-hosted nodules than for the sediment-hosted kerogen seams. Raman spectroscopy indicates that granite-hosted kerogen is more highly ordered than Witwatersrand seam kerogen. A model is presented which links the granitoid­ and sediment-hosted organic matter to an event of oil generation in the Witwatersrand Basin circa 2300 Ma ago. Light hydrocarbons migrated through the sediments and into underlying/adjacent granitic rocks, undergoing polymerization and accumulation in response to radiation accompanying the presence of high-uranium phases.

Jan 1, 1994

By J. H. Fulton

Summary Considerable test work has been done with the detachable type of carbide bit. In general, these bits improved drilling operations, but at a bit cost .greater than was compensated for by the reduction in man-hours of labour. Too few bits continued in service for the possible drilling life of the carbide inserts, and technical improvements or lowered first cost, preferably .both, are indicated ?in order that the bits can be generally acceptable as an economical drilling tool. In ?preliminary test work, the drill rods .with ?one insert of the chisel-bit type appear to be more trouble-free, to have a longer life, and to give a somewhat lower bit cost per foot drilled, than other types. INTRODUCTION The object of this paper is to outline briefly the 'methods used and the results obtained in test work with tungsten carbide bits used in combination with the smaller bore, lighter weight rock drills. As various articles have appeared in the past few years giving the historical background ?and early development of carbide ?bits, this information will not be repeated. Table I lists the equipment used in the test work. The stopers weigh about 95 pounds and the jackhammers with airleg from 97 to 110pounds. The smaller rock drills are stated to deliver about 2,200 blows per minute at 1 to 30 rotation and to require 85 to 95 cubic feet of air at around 100 pounds pressure.

Jan 1, 1950

By A. S. Gendron

A brief description of Inco's ORC copper refinery tankhouse and the electrowinning tankhouse is followed by a comparison of the requirements for the production of the high-quality copper in both systems. The description will focus on both tankhouses, with emphasis on experience to date in the electrowinning tankhouse. Particular attention will be paid to sensitivities of each tankhouse to process upsets which can. significantly afject the quality of the product cathodes.

Jan 1, 1977

By C. H. Wright

Introduction The rapidly expanding and increasingly complex Canadian industrial structure, with the mining, metallurgical, and chemical industries as a large integral part, has, in recent years, brought greatly increased importance and value to our industrial minerals. In the modern economy of our mineral industry the importance which is due the non-metallics has been somewhat overshadowed by the great value of our large metal production and, in addition, by the glamour and fascination usually associated with the mining and treatment of gold ores. The term 'Industrial Mineral' is used in this paper in its usual sense and refers to non-metallics other than fuels. Coal and petroleum products, including natural gas, are considered as industrial minerals in those applications in which they are used for strictly chemical process purposes. Certain reduction metallurgical industries are so closely allied to chemical industries that for purposes been of this discussion no attempt has made to differentiate between them. Chemical industry in Canada today is a fairly large factor in our national economy, whereas in 1898, when the Canadian Mining Institute was born, it was very small indeed. Chemical concerns are largely dependent on industrial minerals for raw materials and process supplies and, as the country has developed industrially, so have the demands for non-metallics increased, not only by chemical industry but also by other large consumers, such as the construction and metallurgical industries. At the present time there is a greater than normal incentive prevailing for new discoveries, due to the serious lack of balance that exists in our import and export trade. This fact has resulted in intensive efforts to rectify the situation by locating new deposits and re-assessing those already known in an effort to enlarge and improve our home production of raw materials and also to extend their processing in Canada for our own needs and for export. The rapid advances in science and technology that have taken place since 1900 have also resulted in many cases of beneficiation and utilization of otherwise too low grade materials in order to satisfy current demands. The purpose of this paper is to indicate the history and the trends of the utilization of industrial minerals in established industry and to indicate the important part played by non-metallics in connection with the opening up of new industries. Some consideration has been given to the continual competition between natural and 'synthetic products and to the general tendency towards more rigid specifications.

Jan 1, 1948

By W. A. Gow, V. F. Harrison, H. H. Mccreedy

A semi-continuous bench-scale, countercurrent-decantation system, in which the ore was moved countercurrently to the flow of leaching solution, was used to conduct acid-leaching tests on uranium ore with the aid of bacteria. This method, which involved a low degree of agitation, was successfully applied to extract uranium in practical amounts and at practical rates. The acidity of the leaching solution was the main variable investigated in the bench-scale tests done at the Mines Branch, Ottawa. Over 90 11er cent of the uranium was extracted in a six-stage system. The results suggest that this technique could be ap-plied in the utilization of bacterial oxidation and leaching as a method for treating Elliot Lake uranium ore.

Jan 1, 1969