Search Documents

By C. M. Anson

Introduction The prosperity of any country today is dependent upon the efficiency and growth of its primary steel industry. The ?march of the United States of America to its present commanding position in world affairs parallels the growth of its steel industry. The remarkable growth of that industry was possible only because bountiful providence endowed that country with adequate supplies of the raw materials necessary for steel making -coal and iron ore. If we accept this hypothesis, and surely we must, then to what extent can we envisage the future of our own country? This symposium deals with the most important of the raw materials required for steel making -iron ore. If we are blessed with a bountiful supply of iron ore, then surely a glorious future awaits only our taking advantage of that blessing. It is becoming increasingly evident that Canada has immense iron ore deposits. It is my privilege to make you acquainted with one of these, one that can only be classified as among the more important ore reserves in the world. I refer to the Wabana ore deposits in Newfoundland. Location These deposits lie under the floor? of Conception bay, off the east coast of Newfoundland. They consist of a series of beds which outcropped for a distance of about three miles on the northeastern shore of Bell Island, dipping at approximately 8° toward the northwest. This three-mile outcrop is the only key to the occurrence.

Jan 1, 1951

By N. Melnyk, H W. Habgood

The conventional low temperature process for extracting' helium from natural gas involves liquefying the whole gas stream in order to remove the relatively small fraction of helium. A process based on the selective diffusion of helium through a semi-permeable barrier is, in principle, more economical and flexible, particularly for the treatment of small re-serves and low concentrations. The well-known permeability of glass to helium offers the possibility of such a diffusion process and McAfee of the Bell telephone Laboratories showed in 1958 that practical separations could be achieved by passing natural gas over bundles of fine capillary glass tubing. Developmental studies have been carried out involving larger units and more extended field tests than those of McAfee. Fine capillary tubing of Pyrex glass 0.0035 in. diameter was prepared by drawing ordinary 6 mm. laboratory tubing in a furnace. Extraction units were pre-pared containing about 10,000 such tubes, 4 ft. long and cemented inside

Jan 1, 1961

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By J. A. Relf

The construction of refineries and gas conservation plants in the general Edmonton area in the early 1950's made available large quantities of by-product liquified petroleum gases (LPG). These gases, together with discovery of increasing reserves of natural gas in the Edmonton area, provided Canadian Chemical Company with two of the necessities for petrochemical production, namely, available and reasonably priced raw materials and fuel. This paper outlines the development of the $83 million Edmonton plant from its origin, together with a brief description of the processes and some of the interesting features involved. Several economic aspects of the petrochemical industry are high-lighted including its importance to the local community and the province. The paper reviews the relationship between the oil and gas industry and petrochemical manufacturing and indicates some of the factors that may affect the future growth of the petro-chemical industry in Wes tern Canada.

Jan 1, 1962

By C. O. Stee

Introduction The property of Siscoe Gold Mines, Limited, is located on an island of three hundred and forty acres in lake Kienawisik, about fifty-two miles east of Noranda and forty-three miles south of Amos, Quebec. Lake Kienawisik is a part of the Harricanaw drainage system and is crossed by the main line of the Canadian National railway at Amos. This waterway is navigable for boats with a draught of six to eight feet. Diesel engines have been the source of power at the property since milling operations were commenced in January, 1929. The power plant as first designed and built was for a milling capacity of 100 tons. Two Polar-Atlas units, each of 200 h. p., comprised the original installation. With the growth of the 'mine, more engines were added until, at the present time, there is installed at the Siscoe what is rated the largest Diesel plant at any mining property in Canada. Definition of a Diesel 'The Diesel engine is an internal combustion engine which works with liquid fuel introduced after, and independently of, the air charge at a time when communication between the cylinder and the outside atmosphere is cut off, and which ignites the fuel by compression-beat and stored combustion-heat unassisted by heat sources outside the cylinder itself while the engine is in stable operating condition"(1).

Jan 1, 1934

By W. E. Lockley

This paper will attempt to answer a number of questions which are important to the safe and continued operation of an electric power system. 1. WHY should electrical protective devices be tested? 2. WHAT devices should be tested ? 3. WHEN should they be tested ? 4. HOW should they be tested? 5. WHO should test them ?

Jan 1, 1977

By J. E. Hawley

Abstract Spectrographic methods for the analysis of minor constituents such as platinum-group metals, gold, silver, and silica in palladium and platinum refinery sponge are described. These involve the conversion of the sponge metals to the black form by reduction with high purity aluminum filings in either acid or alkaline media. Standards of known composition are prepared in the same manner from either refinery or spectrographically standardized sponge metals. Samples of the black metals are mounted in pellet form and a multisource spark discharge used for excitation. The range of concentrations of impurities studied are those common to refinery samples. Excellent reproducibility of intensity ratios using major constituents as internal standards, is demonstrated and two methods have noted by which the accuracy of the procedures are shown to be of the order of 3 per cent, on the basis of synthetic preparations. Introduction During the past two years an investigation has been carried out in the Spectrographic Laboratory, Queen's University, to determine the suitability of modern spectrographic techniques for the precise analysis of the platinum-group metals palladium, platinum, rhodium, iridium, and ruthenium in the form of refinery sponge analyzing about 99 per cent of the major constituent.

Jan 1, 1951

By David E. Pearson

"There are many tests that can be used to characterize and classify coals, and describe their quality. One of the easier tests, and most versatile in its application, is petrography. Rank and coal type are precisely defined by petrographic evaluation, and in this paper they are compared with other definitions of rank and coal type. Brief descriptions are given of the various rank tests, and of rheological and coking tests used to describe coking-coal quality in Canada. Similarly, tests used to evaluate thermal coal quality are discussed. Finally, the use of these tests as parameters to classify Canadian coals is examined with reference to four coal classifications.Introduction Among all coals there are two independent variables that are required to evaluate coal quality. These are, coal rank and coal type (or composition), and although coal petrography can be used to precisely define them, other methods are often used to provide values that are, in fact, functions of rank and coal type. For example, volatile matter yield is used as a proxy for rank, and free swelling index is used as a proxy for coal type in the International Classification of Hard Coals by type. Currently, there are a number of methods in use in Canada to define rank. The approach taken here, (obviously the author's bias), is that Romax, the mean maximum reflectance of vitrinite, is both a quick and an accurate measure of rank. It is logical to compare the other techniques employed in the measurement of rank to this favoured method. Coal type is, in theory at least, simply a quantitative measure of the various varieties of coal. In practice, the microscopic entities are assigned to a Reactive or Inert category, and at that point objectivity fades from petrography. Despite this somewhat subjective approach, petrographic composition of coals remains an independent variable of such.importance that its place in the evaluation of coal is essential. In this paper, a variety of me.thods that are used to assess rank and coal type are reviewed and compared; the influence of these variables over other parameters that are used to determine the quality of metallurgical and thermal coals is examined, and their usefulness in coal classifications is discussed."

Jan 1, 1985

By M. M. Williams

WESTERN CAN ADA'S coal industry has experienced a serious set-back since 1949, following a pattern well known to its counterpart in the United States. The loss in coal markets in Western Canada has been particularly severe as the discovery of large reserves of oil and natural gas and the subsequent construction of re-fineries and pipelines roughly coincided with the dieselization of both main railways. While the coal industry will have to face a further decline in markets of long standing, others with a large growth potential can be se-cured if present marketing methods are changed where needed and if fundamental and applied research programmes are actively pursued. The energy and chemical potential of Western Canada's coals will eventually find their place in the ever-growing needs of industry and electric power producers. Electric power generation would appear to offer the largest and most immediate market for coal. If the coal industry is to serve this market adequately and gain as much of it as possible, coal operators ? must have a good knowledge of certain characteristics -of the electric utility industry and its fuel requirements. This paper is prepared primarily to set out some of these characteristics, but also discusses other probable markets for coal.

Jan 1, 1958

By G. P. Contractor

Medium and low carbon steels, modified with uranium, were studied in order to evaluate the influence of uranium on forge ability, mechanical 11roperties, response to heat treatment and microstructure. Uranium contents ranged up to 0.70 per cent. The medium carbon steels are hot short if the uranium content exceeds about 0.35 per cent. More uranium can be tolerated in low carbon steels. The hot shortness is caused by the formation of intergranular phase UFe2. Critical transformation temperatures, Jominy hardenability, and resistance to tempering are not significantly affected by the 11resence of uranium. Similarly, uranium has little or no effect on the tensile properties of carbon steels. The addition of uranium has a favourable effect 11n the stress-rupture characteristics and some beneficial effect on fatigue properties. However, more results are required for verification. In the steels investigated, it seems that most of the uranium carbide combines to form complex inclusions of U (0, C, N) or (C, N), rich in oxygen or nitrogen or both.

Jan 1, 1963

By T. S. Smith

INTRODUCTION IN PREPARING this paper for the District 4 Meeting, three factors had to be considered. First, the paper must fit the time alloted; second, it must give a general picture of the geology for those unfamiliar with the property; and third, it must contain some new material in order to be of interest to local delegates. The most comprehensive extant discussion of the geology of the property of McKenzie Red Lake Gold Mines, Limited, is contained in Horwood's report on the general Red Lake area ( 1). This report is the 'bible' of the area, and a general paper on the geology of this particular mine would almost certainly appear to be a condensation of it. It was thought, therefore, that the most suitable procedure would be to base the general outline on Horwood' s report, to extend that outline where possible from information gained since its publication, and finally to leave dangling for the contemplative geologist some of the ideas and problems which ?are currently under consideration. LOCATION AND HISTORY The property of McKenzie Red Lake Gold Mines, Limited, is in Dome township, in the Red Lake mining division of northwestern Ontario. The mine is on McKenzie Island, about four miles north, by water, of the Hasaga mine and old Howey mine.

Jan 1, 1951

By D. D. Bell

This paper presents the history of uranium procurement and demand, and takes a look at future requirements. The three basic conclusions drawn are: (1) the productive capacity of former and existing producers whose operations may be profitably reactivated is insufficient to meet demand projected beyond 1975; (2) reserves in the $5 -$10 price range do not provide the flexibility to sustain production at the high rates required in the late 1970's; and (3) only higher prices can overcome these deficiencies, as this would provide sufficient inducement for the industry to explore for and develop new reserves and productive capacity.

Jan 1, 1967

By Kurt F. Weitz

"The number of materials that can be classified as fillers covers an extremely wide range: this paper outlines those fillers of the industrial mineral type that find extensive application in the paint and plastics industriesIn the paint industry, mineral fillers are known as extender pigments. Extenders are added to paint and plastic compositions to (1) lower the cost and (2) rein-force or modify the physical properties of a composition.Commonly used extenders are classified according to chemical type and discussed in terms of the change in physical properties that they impart to a paint or plastic film. Available cost reductions and data on the consumption of extenders in the Canadian paint industry are also included."

Jan 1, 1970

By Robert L. Tremblay

Dans le but de voir si une région comme la Gaspésie, qui a subi la derniere glaciation , se prête avantageusement à la méthode de prospection alluvionnaire, environ 800 concentrés de minéraux lourds furent prélevés dans les districts électoraux de Matane et de Gaspé-Nord. Les différentes phases minérales présentes dans les concentrés ont été examinées à la loupe binoculaire. Afin de mieux valoriser ce type d'inforrnat ion, nous avons été arnenés à expérimenter et à mettre en oeuvre des techniques multivariables adaptées au traltement d'une information semi-quantitative en utilisant le principe d'un codage logique préalable. La structuration des résultats de la Gaspésie a conduit à l'élaboration de cartes de synthèse qui constituent un support nécessaire à l'interprétatlon des répartitions plus ponctuelles des minéraux "utiles" sur le plan de la recherche minière.

Jan 1, 1978

By E. Busse

"Heath Steele Mines Ltd. operates a lead-zinc-copper mining and milling complex in New Brunswick.• During the past seven years, as ore reserves increased, the mill capacity was first expanded to 1,600 tpd and then to 3,000 tpd. In the last expansion, instead of building a completely new 3,000-tpd mill, or adding to existing installations, Heath Steele retained service facilities, buildings, ore bins, Jab, etc., and removed and replaced almost all existing process facilities. Requiring a complete mill shutdown, the expansion had to be carried out in minimum time. Also, new equipment had to fit into existing space. Critical path networks of the project were prepared, a tight schedule for construction was mapped out and progress charted daily to detect problems before they could interrupt the schedule. Heath Steele supervised the purchasing, handling and storage of new equipment, maintained liaison with the engineering contractor and became a sub-contractor, using its own staff to install all flotation equipment and process piping. The 1,600-tpd installation was dismantled and a 3,000- tpd unit was successfully put onstream in 5 months - on time and within budget. One benefit stemming from the expansion: production increased 87 per cent while operating and maintenance labour rose only 8 per cent."

Jan 1, 1972

By Mohsen Mohammadi, Edward Cyr

"To date, several studies have been performed on the static mechanical properties of SLM-AlSi10Mg alloy. There have also been more recent studies on the relation between scan strategy, texture, and mechanical properties of SLM metals and composites. However, there is a huge knowledge gap in the available literature regarding texture and mechanical behavior of SLM-AlSi10Mg alloy under high strain rates. Therefore, in this study, dynamic mechanical behavior of AlSi10Mg_200C alloy manufactured by DMLS technique was investigated at high strain rates ranging from 900/s to 1700/s using Split Hopkinson Pressure Bar. Texture using X-ray diffraction technique of the initial samples were measured. The yield strength, peak flow stress, and ductility increased in all samples with increase of strain rate. TEM studies have also revealed evidence of continuous dynamic recrystallization in grains after 900/s–1700/s strain-rate tests. A Taylor polycrystal crystal plasticity constitutive model was then developed to capture and predict the texture evolution and mechanical response under dynamic loading, using plastic work as a critical parameter for the onset of recrystallization.INTRODUCTION Additive manufacturing (AM) powder techniques are among the fastest advancing breakthroughs in manufacturing in recent years, defined by a bottom-up layer by layer process of joining with energy input from lasers or electron beam (Herzog et al., 2016; Gibson et al., 2015). Among alloys fabricated by SLM, AlSi10Mg is of high interest to industry and academia due to its low density, high specific strength and excellent corrosion resistance, making this alloy a viable contender for aerospace, automotive, and marine applications. Circumstances such as car crash or bird aircraft strike hazards subject potential additively manufactured AlSi10Mg parts to impact loadings. This drives an interest in understanding and predicting dynamic behaviour of these alloys. AlSi10Mg is the AM counterpart of A360 die-cast aluminum, which possess hypoeutectic microstructure (Li et al., 2015). Up to the present time, many studies have presented the mechanical properties of SLM-AlSi10Mg alloy. The mechanical properties and microstructure of AlSi10Mg produced by selective laser melting (SLM) or DMLS techniques can be controlled using different parameters, such as feedstock powder (Asgari et al., 2017), and process parameters (Olakanmi et al., 2015). The microstructure and mechanical properties of AlSi10Mg can also be controlled using post heat treatment after SLM process Li et al., 2016). The mechanical properties of SLM-AlSi10Mg are sensitive to strain rate and can both change under quasi-static (Rosenthal et al., 2017) and high strain rates (Asgari et al., 2018). However, a significant knowledge gap in available literature regarding modeling these behaviours, and especially micromechanical modeling of dynamic behaviour."

Jan 1, 2018

By Marvin E. Lane

Viburnum, located in the foothills of the Ozarks in south-east Missouri, is the site of a modern lead mining and milling operation. Two mines are currently producing a total of 5,000 tons per day and a third mine is in the final development stage, with full production scheduled for late this year (1964). These mines will supply the tonnage required to keep the Viburnum mill operating at a full capacity of 7,000 tons per day for many years. The efficient underground mining operation is completely trackless. Drill jumbos are used to break the ore in a room and pillar method of mining. Transloaders, or St. Joe shovels, and trucks do the loading and hauling. The Viburnum mill has a world-wide reputation as a most efficient operation. This is due to the extensive use of automatic process controls, and labour saving materials handling facilities. Introduction THE St. Joseph Lead Co., has operated lead mines in southeast Missouri for 100 years. These operations have been confined largely to the area called the

Jan 1, 1964

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By A. Takala, H. Cline, D. Girard

"This article describes the project development and successful implementation of a particle sorter at the Kensington mine. The Kensington underground gold mine and associated milling facilities are located within the Berners Bay Mining District on the east side of Lynn Canal about 45 miles north-northwest of Juneau, Alaska. The paper describes the project from concept, through the development phase, including test work confirming feasibility, to a discussion of operational data and includes shared experiences from operation and maintenance. The project has proven successful in recovering gold that was previously lost to the waste dump and has already resulted in a positive return on investment. The payback was achieved in less than one year.INTRODUCTION The first paragraphs of this paper describe Coeur Mining and the Kensington Mine, its history, geology, mining operation and mill. The second part of this paper gives a quick introduction to sensor-based sorting in general and X-ray transmission sorting (XRT) in particular. This article does not cover costs or economic impacts apart from the pay-back period for the investment at Kensington. Interested readers find more in information on this in the literature (Kleine & Wotruba, 2010; Robben, 2013). Since the publication about XRT sorting at TGME in Pilgrim’s Rest (Kleine, Riedel, Ketelhodt, & Murray, 2010), this is the first time that a comprehensive data set on gold ore sorting using XRT is published. Following chapters highlight the aim of the project for Coeur Kensington, project development through testing and operation before concluding. ABOUT COEUR MINING’S KENSINGTON OPERATION Coeur Mining is the largest U.S.-based silver producer and a significant gold producer with five precious metals mines in the Americas employing approximately 2,100 people. Coeur produces from its wholly owned operations: the Palmarejo silver-gold mine in Mexico, the San Bartolomé silver mine in Bolivia, the Rochester silver-gold mine in Nevada, the Kensington gold mine in Alaska, and the Wharf gold mine in South Dakota. The Company also has a non-operating interest in the Endeavor mine in Australia in addition to royalties on the Cerro Bayo mine in Chile, the El Gallo complex in Mexico, the Zaruma mine in Ecuador, and the Correnso mine in New Zealand. In addition, the Company has two silver-gold feasibility stage projects—the La Preciosa project in Mexico and the Joaquin project in Argentina. The Company also conducts ongoing exploration activities in Alaska, Argentina, Bolivia, Mexico, and Nevada. The Company owns strategic investment positions in several silver and gold development companies with projects in North and South America."

Jan 1, 2017

By H. S. Price, F. N. Kissell, R. C. McCulloch, J. C. Edwards

"The methane em1ss10n from deep coalbeds which are actively mined is a serious problem facing the mining industry today. Pinpointing the source of methane and predicting the emission of this gas from these coalbeds is necessary if preventive techniques are to be effectively used to control methane emission. In general, because most coalbeds have water associated with them, the system to be studied may be either single-phase (methane gas) or two-phase (methane and water). Because coal mine geometry is complex and the fluids have variable properties as functions of pressure and methane concentration, the differential equations describing the flow of methane and water are not amenable to analytic solution, but must be solved numerically using high-speed computers. This paper presents the development of such a complex mathematical model along with some preliminary applications of the model to methane emission from one- and two-dimensional coalbeds with and without water present."

Jan 1, 1973