Search Documents

By W. T. Martson

ABSTRACT Sooner or later, every producing mine faces the question of fill. This paper invites consideration of mill tailings as an economical, efficient, and quantitatively adequate source of such fill. Some of the advantages, disadvantages, methods of utilization, and methods of treating mill tailings for sand recovery are covered. ADVANTAGES AND DISADVANTAGES OF SAND FILL DISREGARDING economic com-promise, that material which supports the greatest applied load with the least compression is the best choice for fill. Table I, reproduced from U. S. Bureau of Mines Bulletin 60, is offered as evidence of the adequacy of hydraulically placed sand. Table II gives the results of tests made in an effort to determine the reason for the difference between load hearing qualities of dry-placed and hydraulically-placed sand. From these, it would appear that hydraulic placing gives a denser initial packing, with corresponding higher, and faster development of, load bearing qualities. Assuming this to be true, then if sand from mill tailings can be placed underground economically, it is the superior fill material. Table III summarizes cost data available. The most cursory glance through the available references (2, 5, 6, 7, 8, 9) will show .that the major benefit from the adoption of sand fill is a decrease in the non-productive fill ?cycle of a working place. This, it is estimated, increases the output of an individual stope by from 25 to 50 per cent. The advantage of reducing the number of required working places for a constant daily production is obvious.

Jan 1, 1951

By Paul J. Bourassa

Alin de pourvoir aux besoins d'hébergement des quel¬ques 1600 employes qui travailleront dans toutes les spheres opérationnelles de l'exploitation du gisement du Mont-Wright, ainsi que de leurs families, Quebec Cartier a dû, avec l'aide de conseillers reconnus, et /a participation de ses employes résidant a Gagnon, étudier tour les nouveaux établissements résidentiels nordiques des dernières années tout au Canada qui dans lee pays scandinaves afin d'être en position de coneepter une agglomeration moderne répondant a toes les besoins de see future résidants. Les pre¬miers residants ont pu passer Noel 1972, et maintenant les logements prévus et construits sont °coupes a 92%.

Jan 1, 1977

By J. C. Salas, A. Weishaupt, J. A. Guzman

The origins of the electrorefining process date back to 1869, when the first ER cathodes were produced at Pembrey, South Wales. By the time that Pembrey was closing, Chuquicamata tank house was under construction, initiating in 1915 a long history of electrolytic cathodes production. Initially electrowon cathodes and later electrorefined cathodes were produced. During the history of Chuquicamata tank house, there have been several challenges associated with the quality demanded for electrolytic copper. Among them, the transformation from electrowinning to electrorefining in 1952, the onset of the direct commercialization of ER cathodes and the phase out of wire bars in the 80s, several technological changes including the implementation of permanent cathodes, and certainly the constant increase in complexity of the anodes refined. This paper explores the manner in which Chuquicamata has addressed these challenges and examines its links to process characteristics, which have been necessary to maintain a product quality according to market requirements and a brand, “CCC”, that is widely recognized worldwide. INTRODUCTION Located in the north of Chile, in the Atacama Desert, Chuquicamata is an open pit copper mine that for many years has played a relevant role in the global and local mining industry. Known from prehispanic times, the Chuquicamata deposit was initially developed between 1912 and 1915 by the Chile Exploration Company, the operating company of the Chile Copper Company controlled by the Guggenheim Brothers in the USA (Yeatman, 1916). Officially inaugurated on May 18th, 1915, by the President of Chile who pressed a button in Santiago sending a telegraph signal to the power generation plant specially built in Tocopilla, 1500 km north. It signaled the beginning of generating energy, sending it to Chuquicamata, another 140 km east (“El mineral de Chuquicamata”, 1915), marking the beginning of its industrial operation.

Jan 1, 2019

By L O. Montpetit

The economics of the asbestos mining industry of Canada, and the physical and chemical characteristics of asbestos fibre, as well as exploration, mining, milling and quality control methods, have been described by several authors in the past few years. The scope of this presentation is to survey the application of asbestos fibres in the major product groups of the construction industry in North America. Principal categories considered include flooring materials, asbestos-cement pipes and building products, high-temperature insulation, textiles, saturated asbestos felts and asphalt com pounds. During 1962, the asbestos mining industry of Canada produced an estimated 1.3 million tons of chrysotile fibre grades, and production capacity is expanding. The market demand for chrysotile fibre, on this continent, has been in the order of 50 per cent of the production volume. The asbestos industry is dependent for growth on the construction industry. Product research is active in finding new uses for asbestos fibre; some of the new developments are presented, including the use of short-fibre asbestos grades for extending the life of asphalt pavement.

Jan 1, 1963

By Bunting S. Crocker

This paper reviews the trends in the past two years in autogenous grinding throughout the world. It covers rock grinding in South Africa, Sweden, Canada, the United States, Finland and Germany. To properly orient the discussion on this subject, the paper attempts to define and classify the scope of autogenous comminution. As this is a relatively new subject, there is often considerable confusion regarding the various practices, which sometimes differ widely. By clarifying the types and forms, we hope to help clear up this con-fusion. Autogenous grinding is being carried out, throughout the world, either in mills grinding in water or solution or in dry mills using air classification to remove the finished material. The wet grinding, particularly, can be divided into: (1) (2) (3) Primary autogenous grinding, or "run-of-mine" grinding. Secondary autogenous grinding or semi-autogenous grinding or rock pebble grinding. Combination processes. -This covers plants in which pebbles made in the primary mill are re-moved and used as grinding media for fine grinding in secondary mills.

Jan 1, 1963

By Joseph U. Messenger

A method of applying ammonium hydroxide to a drill stem containing hydrogen sulphide gas and hydro-gen-sulphide-bearing oil and water so as to remove the hydrogen sulphide as ammonium sulphide is de-scribed. It was concluded that the method allowed trips with drill pipe filled with sour fluids to be made more safely, more rapidly, and more economically. INTRODUCTION THE DANGER of poisoning rig crews during drill stem tests of sour wells by exposing them to hydrogen sulphide gas is well known in Canada. Concentrations of hydro-gen sulphide in sour gases range from 0 to 40 volume percent. There have been numerous casualties from hydrogen sulphide exposure during drill stem testing. Some have resulted in permanent injuries; in some cases the injuries have been fatal. For example, in Alberta in 1957 there were four deaths and 100 exposures which required medical treatment. These fatalities and injuries indicate the need for a more effective way of handling hydrogen sulphide in oilfield operations.

Jan 1, 1958

By Rodney R. Koch

The phys ica l properties of gold should faci li tate its detection. However, the average concentration of gold in the ea rth's cru st precl udes the ability of geophys ical methods to detect the metal directly. In order to effectively pursue geophys ical detection and location of gold mineralization there must also be geological input - i.e. a model. This will lead to the selection of the appropriate geophy ical techn ique(s) in the fo llow-up programs. Interpretation of the fie ld survey data is of con iderable importance in expl oration geophys ics. Analytical techniques such as cont inuation, fi ltering, and spectral analys is, are now routinely empl oyed in the analys is of survey data to aid the interpretation process. The uccessful application of geophysical methods and the use processing techniques is demonstrated by two recent Saskatchewan discoveries. The first, the Star Lake 21 Zone, with reserves of 230,000 tons grading bener than 17.14 git Au associated with a disseminated sulphide quartz-bearing shear zone yielded geophysical anomalies that were distinctive, obvious, and would have lead directly to its discovery. The econd , the Laurel Lake Prospect, with ore grade intersections of 28.0I git Au and 52 .46 git Ag· over 5.49 m, resulted in numerous geophysical anomalies. However, none of these anomalies demonstrated association with the mineralization until processed results indicated that structural features crosscuning regional trends were important cont rol mechanisms for the mineral ization.

Jan 1, 1986

By D. E. G. Maschmeyer

The operation of the pilot plant for the S-C Copper Process during 1976 has provided the basic data for the design of a commercial-scale plant. This paper introduces the commercial aspects of the S-C Copper Process through the presentation of a process flow diagram, a schematic flow diagram and basic design parameters for 75,000 tonnes per year (tpy) copper rod production from chalcopyrite concentrate. Basic operating requirements are outlined and a preliminary estimate of operating and capital costs for a Western Canadian location are summarized. The results have been compared with a modern smelter/electrorefinery to highlight the advantages and disadvantages of these two alternatives and to show why the new S-C Copper Process technology should be of interest to the copper industry.

Jan 1, 1978

By V. L. Gravitis

Radioisotope X -ray techniques of analysis for nickel have been tested in laboratory and plant trials. In the laboratory tests. a comparison was made of radioisotope and conventional analyses for nickel in solid s samples taken from streams of a nickel concentrator. Coefficients of variation of 1.7% for feed and concentrate samples , and equal to 10% for final tailing samples, were obtained. Continuous determination of nickel in final tailing slurries was demonstrated in a trial lasting 20 days at a nickel concentrator (Western Mining Corporation), nickel being determined with a standard error of 0.036% Ni in the slurry solids within the range of 0.24 to 0.68% Ni. This error, obtained by comparison of on-stream probe analyses with assays of samples taken from the stream, includes errors in sampling and assay by conventional techniques.

Jan 1, 1977

By Rodney Allen

Background: Development of the Project ?European GEODE collaboration 1999: considers possible projects, including a VMS project, to continue after GEODE ?GEODE-CODES-Canada collaboration 1999: Questionaire, database ?Workshop at CODES 2000: project theme and strategy selected ?GEORANGE (Sweden-EU) 2001 supports development of Global VMS Project: interest from 12 nations ?Skellefte VMS Project set up as Sweden?s component of Global VMS, 2002; other projects in Spain, Canada collaborate ?Low metal prices ---> little funding from mining industry 2001-2003, change in strategy ?IGCP/UNESCO support 2004: enlargement to over 20 nations

Apr 1, 2005

By M. A. Rabah

This study aims to recover europium, yttrium metals, some valuable salts or oxides from the white powder (apatite) coating the inner surface of spent florescent lamps (SFLs). Pressure leaching using sulphuric/nitric acid successfully dissolved the metals of interest. Europium or yttrium metals were obtained by hydrogen reduction of their oxides. Addition of potassium thiocyanate converted the dissolved sulphates to thiocyanates. Selective separation of Eu and Y was then carried out by solvent extraction from the thiocyanate solution. The used solvent was trimethyl-benzylammonium chloride. N-trihutylphosphate in 1 M nitric acid was used to strip the metal loaded in the organic phase. Results showed that the quality of the cleaned glass tubes of the SFL met the standard requirement for the lamp manufacture. The white powder (WP) is composed of calcium sulphate 35.2%, phosphate 61.5% and oxides of europium and yttrium 1.65%wt. respectively. Autoclave digestion of the WP for 4 h at 120°C and 500 kPa in sulphuric acid/nitric acid mixture dissolved 96.4% of yttrium and 92.8% of europium. The conversion rate of sulphate to thiocyanate was favoured at low temperature. Stripping of Eu and Y from the loaded organic phase behaved in an opposite way. A metal separation factor of 9.4 was obtained. ate recovered europium and yttrium salts were selectively separated using ethyl alcohol or dilute nitric acid. Yttrium was very soluble while europium was not. Europium and yttrium metals were obtained by hydrogen gas reduction at 850°C and 1575°C respectively.

Jan 1, 2004

By N Robb

This paper gives an account of the laboratory testing, plant testing and final inclusion of the two-stage sulphuric acid leaching process in the Milliken mill. Operational results for September, 1962, are presented, showing a uranium extraction of 95.5 per cent, with a saving of some 16 lbs. of 100 per cent H~S04 and some 9 lbs. of lime per ton milled. Methods for effecting further improvements in the process are indicated. HISTORY P RIOR to the incorporation of two-stage leaching, the process for the treatment of uranium ores at Milliken consisted of a single-stage sulphuric acid leach, followed by a solution recovery step involving washing in thickeners and two-stage filtration. The thickener overflow solution was subsequently concentrated and purified by ion exchange, and the uranium was recovered, by two-stage precipitation, as ammonium diuranate. Figure I illustrates this flowsheet. For satisfactory extraction of uranium from the. Milliken ore, a high residual acidity, of the order of 40 grams per litre of free acid in the discharge solution, must be

Jan 1, 1963

By G. Scamans, J. Lazaro-Nebreda, Z. Fan, J. B. Patel

"Melt quality is crucial for both continuous and shape casting of light alloys and in order to improve it, removal of excessive inclusions, accumulated impurities and unwanted gases becomes necessary. To address this problem, a new multi-purpose high shear liquid metal treatment technology, based on intensive melt shearing by a rotor/stator unit, has been developed. The device ensures achieving uniform temperature and chemical composition and an efficient dispersion of gas and solid phases in the melt with minimal disturbance of melt surface, and can be used, among other things, for de-gassing and de-ironing of Al-alloy melts. Efficient degassing is achieved by dispersing each argon bubble into many small ones, which significantly increases the overall surface area of the bubbles and the time they remain in the melt capturing hydrogen before reaching the surface. This allows using much lower inert gas flow and mixing times than conventional rotary degassing. When applied to Al-alloy scrap, with accumulated iron, the high shear melt treatment speeds up the nucleation and growth of primary Fe-rich intermetallic particles, allowing a faster removal rate. Therefore it reduces processing times, increasing recycling productivity, and facilitates full metal circulation of secondary Al-alloys.INTRODUCTION Aluminium and magnesium alloys are widely considered in various industrial sectors for the purpose of weight saving (Polmear, 1995). In particular, they are used in the automotive sector, where components are mostly manufactured by high pressure die casting (HPDC) because of its simplicity and relatively low cost, but efficiency and mechanical properties are quite low compared with other processes. To date, the main focus to overcome this problem has been for improving the HPDC machinery (Dahle, 2001) but little attention has been paid to the opportunities of controlling the nature and quality of the molten metal supplied to the die. In this way, liquid metal treatment, which involves a variety of physical and/or chemical processing methods to improve melt quality prior casting, is crucial for both continuous and shape casting products."

Jan 1, 2018

By Wm Petruk

"The tungsten-bismuth-molybdenum deposit in southwestern New Brunswick occurs in greisenized and silicified tuffite * and feldspar porphyry in and adjacent to volcanic necks. The ore minerals occur as veins and veinlets and as disseminated grains in gangue. These minerals can be grouped into three assemblages. Assemblage 1 consists of oxides and phosphates of W, Ti, Fe, Nb, Sn, Ta and rare-earth elements, with the main minerals being deposited in the sequence wolframite, rutile, cassiterite. Assemblage 2 consists of arsenopyrite, molybdenite and bismuth, and assemblage 3 of sulphides with minor cassiterite and arsenopyrite. Sphalerite is the main sulphide mineral, but it contains minute inclusions of copper-tin- and indium-bearing minerals. Textural relations suggest that most of the elements can be recovered from this ore by conventional mineral beneficiation and extraction methods, but a variety of techniques must be employed. It is expected that the wolframite and molybdenite can be recovered satisfactorily, but poor recoveries are expected for bismuth and cassiterite. A sphalerite concentrate can be readily obtained by flotation, but it would contain a wide variety of elements. It is suggested that leaching be used to recover the bismuth and the elements in the sphalerite concentrate."

Jan 1, 1973

By R. A. Price

The base of the biozone of Olenellus is accepted as the most universally applicable criterion for defining the base of the Cambrian System. The use of this definitive criterion is restricted by important practical considerations. In the southeastern Canadian Cordillera this zone appears to truncate the basal ortho-quartzite of a west to east marine -transgression. This transgression began in Interior British Columbia in the Late Proterozoic and terminated in the region of the present Rockies in the Late Waucobian. Most of the material deposited by the transgressing sea originated in the eastern positive element 'Laurentia' and was transported over the intervening low Proterozoic-Windermere erosion surface. The configuration of the advancing shoreline and the distribution of the sediments were controlled by the tectonic activity of positive elements in northwestern Montana (Montania) and in the Fairmont Hot Springs-Radium area of British Columbia.

Jan 1, 1956

By W. B. Boggs

The Noranda smelter was built by Noranda Mines, Limited, from the designs of A. E. Wheeler, consulting metallurgist, New York, for the reduction of ores and concentrates from the Horne mine, and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is situated at Noranda in western Quebec, about 330 miles directly north of Toronto. Ground was first broken for construction in November, 1925, before the completion of the branch railway into the district, which was not finished until October, 1926. After many difficulties and delays due to the Jack 'of transportation and the severe weather during the winter months, the smelter was started in December, 1927, and the first blister copper was poured on December 17th. The smelter was built throughout in two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with only one unit, and after several months it was found that one unit alone would smelt 1,000 tons of ore per day. At this time only one shaft, No. 3, existed, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. This work was completed in the latter part of November, 1929, and since that time both smelter units have been operating.

Jan 1, 1930

By B. A. Strathdee

An arsenical ore containing both pyrite and arsenopyrite was heated to a temperature at which decomposition and distillation took place. The condensate consisted of metallic arsenic and arsenic disulphide, although the analysis of the ore showed that volatile arsenic and sulphur were present in proportion to produce a condensate of arsenic trisulphide and sulphur. Distillation tests on the mineral arsenopyrite also produced a condensate of metallic arsenic and arsenic disulphide. This arsenic sulphide gave a distinct x-ray diffraction pattern which was not listed in the A.S.T.M. data file. This same sulphide can be produced by heating a mixture of arsenic and sulphur in vacuo. Its chemical analysis corresponds to As2S2. The dissociation pressures of arsenopyrite and the vapour pressures of arsenic disulphide and arsenic metal were measured, using a quartz "spoon" gauge. The dissociation pressures of arsenopyrite were compared with the published data for the dissociation pressures of pyrite to account

Jan 1, 1961

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989

By Derek H. C. Wilton

"The Nain Province (NP) of northern Labrador is a >600 km long by =100 km wide Archean craton that has undergone relatively little mineral exploration until economically signifcant concentrations of orthomagmatic nickel sulphide were discovered by Diamond Fields Resources (DFR) at Voisey’s Bay. Due to the great time span between crust formation andfnal intrusive activity (ca. 3.9 Ga to 1.27 Ga),there were, however, numerous metallogenic events within the NP.The NP was intruded by the ca. 1.3 Ga to1.2 Ga Nain Plutonic Suite (NPS) composite anorthosite-granite complex. The NPS dividesthe NP into the southern Hopedale Block (90 km by 150 km) and the northern SaglekBlock (375 km long by =50 km wide). These two blocks appear to represent two distinct Archean cratonic nuclei, each with its own distinct metallogenic history. The NPS is a coalesced assemblage of composite intrusions which include anorthosite, troctolite, norite, gabbro and granite.The Hopedale Block contains the Hunt River and Florence Lake greenstone belts, and the Weekes Amphibolite which represents remnantsf the older Hunt River greenstone belt. Geologically, these belts have some potential to host komatiitic Kambalda-style nickel, volcanogenic massive sulphide (VMS) and meso -thermal lode gold mineralization. The unconformity between Paleoproterozoic cover sequences and the trondhjemite-tonalite-granodiorite (TTG)suite which engulfed the greenstones was the locus for lead-zinc-bearing quartz-carbonate veins. Minor fracture-hosted uraninite showings are also present in the TTG.The Saglek Block is a high-grade gneissterrane with deformed Archean supracrustal sequences but no greenstone belts. Within the gneiss are variably-sized enclaves that range in composition from anorthositic to ultramafic; some of these latter xenoliths contain abun-dant fuchsite. There are also three small anorthositic to ultramafic meta-igneous complexes present in the gneiss near Okak Bay.Some Archean meta sedimentary and maficgneiss supracrustal sequences contain iron-oxide and sulphide members. The sulphide-bearing Tasiuyak parag neiss defines the cra-tonic suture between the NP and Churchill(Rae) Province. Along the cratonic suture between the NP and Churchill Province from Ramah Bay north are remnants of the Archean(or Paleoproterozoic) Hutton Anortho site Suite. Ultramafc layers within the suite contain chromite and elevated Ni values.Three ca. 2.0 Ga supracrustal sequenceswere deposited in small fault-bounded basins within the NP. The Snyder Group contains pyrrhotitiferous massive sulphide horizons. TheMugford Group contains SEDEX-like massive sulphide blocks in a debris fow and ultramafic sills with unusual PGE concentrations; alaskitic granite cutting basement gneiss to the group contains stockwork-like pyritiferous quartz veins. The Ramah Group contains numerous MVT-style zinc-lead sulphide occurrences.The Reid Brook Intrusion of the NPS contains enormous and high-grade nickel-copper-cobalt massive sulphide bodies at the Voisey’s Bay deposit. Exploration in the northern portions of the NPS in 1995 has indicated the presence of other potentially economic nickel sulphide horizons."

Jan 1, 1996

By M. B. McClenaghan, O. P. Lavin, Ian Nichol

"Abstract-Exploration in most areas of Canada has to contend with problems posed by glacial overburden. In many areas exploration for gold has been based on the sampling of tills, frequently by deep overburden drilling, and analyses of heavy mineral concentrates. Notwithstanding the significant role that till geochemistry has played in the discovery of some important gold deposits over the last few years, increased appreciation of the nature of the glacial history and stratigraphy and the character of gold within till has led to the recognition of a number of ways whereby the effectiveness of exploration can be improved upon.In order for till geochemistry to be useful in exploration, a number of conditions must be fulfilled, including:1. mineralization, or alteration halo related to mineralization, subcropping at the bedrock /over­ burden interface; 2.glacial erosion and dispersal of a recognizable signature of mineralization into the glacialsediments; 3, preservation of glacial sediments containing this geochemical component (trace metal or mineral) at positions subsequently selected for sampling (normally drill sites); 4. correct identification of specific till units and associated ice movement history; 5. collection of adequately large and representative samples; 6. appropriate sample preparation and processing; 7, appropriate geochemical analyses; and 8. correct data processing and interpretation.While we have no control over the first two geological conditions, and only limited controlover till availability, we can control the quality and thoroughness of sampling, sample identification, sample preparation, analysis and interpretation. In particular attention needs to be focussed on obtaining a large enough sample to be adequately representative, an unbiased sample must be collected, together with appropriate sample processing, analysis, data processing and interpretation. It is considered that by modifying or extending existing approaches to gold exploration the chances of exploration success can be increased. In particular, analyses of both the heavy mineral and minus 63 ?m fractions of till is recommended because gold in till may occur in different size fractions."

Jan 1, 1992