Search Documents

By P Atkinson, M P. Simpson, J R. Kyle

BM37 is a bonanza-grade (>30 ppm Au) ore shoot of the Maria Lode of the Karangahake adularia-sericite epithermal deposit in the southern Hauraki Goldfield. Samples from BM37 contain up to weight percent gold. The ore shoot is a vein that pinches and swells, but is typically tens of cm thick, and locally exceeds 0.5 m in true width. Gold occurs as irregular anhedral electrum grains that range up to 300 microns across and contain 38 to 59 wt per cent Au (ave. 52 wt per cent Au). Electrum occurs in sulphide-rich bands in association with pyrite, chalcopyrite, acanthite, galena, sphalerite, and local covellite. Lower grade samples contain local to rare mckinstryite [(Ag, Cu) 2S] and polybasite [(Ag, Cu) 16 (As, Sb) 2S11]. Pyrite from BM37 is nearly stoichiometric; it lacks the As that commonly occurs at up to percent levels in pyrite from other veins in the goldfield. Acanthite also contains low quantities of trace metals, and typically has less than 2.5 per cent Se. The vein shows complex textures. Bonanza grade sulphide-rich ginguro bands form discrete layers adjacent to the vein margins, and occur as breccia fragments encased by later massive to comb quartz with local quartz after platy calcite. Both the breccia fragments and ginguro bands are cross-cut by later quartz veins. Textures thus indicate that formation of the high-grade portions of BM37 resulted from one or more discrete events that differed markedly from the events that formed the bulk of the vein.

Jan 1, 2006

By A Priatna, H Rumbino, T Casten

This paper discusses the progress of the Deep Mill Level Zone (DMLZ) mine from the pre-feasibility study completed in 2005, through commencement of development access in 2008, completion of the feasibility in 2010 and cave initiation in late 2015. This fourth lift of caving in the East Ertsberg Skarn System (EESS) is located 500 m below the currently producing Deep Ore Zone (DOZ) mine and represents approximately half a billion tonnes of ore and around 1900 planned drawpoints, scheduled to be mined at a peak of 80 000 t/d.The paper reviews the mine design, access requirements, planned footprint sequence and major fixed facility installations such as ventilation, oreflow and shops. A discussion of the preproduction development and construction activities and some of the critical technical challenges overcome during this time frame are addressed, as well as the cave initiation process undertaken in late 2015 and the ramp-up of production and progression of caving.CITATION:Casten, T, Priatna, A and Rumbino, H, 2016. Deep Mill Level Zone – from feasibility to production, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 635–644 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The mineralogy, textures, and genetic significance of a silver-rich siderite vein and an apparently co-genetic galena vein from the South mine, Broken Hill are discussed.Both veins cut sharply across the Main Lode Horizon and appear to be coeval with thc A.B.H. Consols lode.The minerals of thc siderite vein apparently result from the preferential leaching of silver from Main Lode Horizon ore with a demonstrable "breakdown series" commencing with tetrahedrite, passing through silver sulpho-salts, and ending with simple binary compounds or with elemental silver.The siderite vein has been deposited by metahydrothermal fluids along the lines of Schneiderhohn's "secondary hydrothermal" mineralization.

Jan 1, 1968

The application of biogeochemical methods in mineral exploration in semi-arid to arid environments in Western Australia has been investigated in an area near Norseman.The study involved a comparison of trace element characteristics of rock, soil and plants in the vicinity of the Pioneer BB prospect, where nickel-iron sulphide mineralization occurs in a "greenstone" sequence of ultrabasic, basic and sedimentary rocks.Analyses of unweathered and partly weathered rock from diamond drill cores show the ultrabasic rock to be highly variable with respect to Ni, Cu, Co, Zn and Mn.Samples of weathered bedrock and overlying soil were analysed for total trace element contents and for the trace elements associated with secondary iron and manganese oxides. Approximately 30 per cent of the total nickel content of the weathered basic rock is associated with secondary iron and manganese oxides, compared with approximately 15 per cent in the weathered ultrabasic rock.The soil has a sufficient residual content to provide a reliable indication of the chemistry of the underlying rock. Total trace element analyses of the -89 mesh fraction show strong anomalies for nickel and copper over the mineralized zone. Important amounts of nickel, cobalt and, to a lesser extent, copper are apparently associated with secondary iron and manganese oxides in the soil.Melaleuca sheathiana (tea tree) has been used to study the relationship between soil and plant chemistry. No strong relationship between plant and rock type was observed. Analyses were made of leaves, twigs, wood, bark and roots, and all plant organs were found to have anomalous nickel and copper contents near the mineralized zone. Leaves were found to give the best contrast in the anomalous area and to show fewer erratic values than other organs. It is concluded that the uptake of trace elements by tea tree is low in the semi-arid to arid environment of Western Australia, but that analyses of the plants do reflect the presence of mineralization.

Jan 1, 1973

By D O’Dea, B Godel, T Honeyands, B Ellis, T Harvey

X-ray computed tomography (XCT) is a non-destructive technique that allows the exploration of the internal structure of solid objects in 3D. Over the past ten years, the combination of XCT with more conventional 2D techniques and quantitative 3D image processing and analysis (commonly referred to as digital rocks) has allowed us to address some of the most challenging problems in ore deposit studies. The range of X-ray energies used in XCT allows the X-rays to be transmitted through complex and dense materials including iron ores (eg sinters, lumps, granules). Recent high-resolution XCT scanners have the ability to generate multiscale (25 down to 0.3 µm voxel size) imaging of a given sample enabling the characterisation of 3D textures across a range of scales. This paper will focus on the application of digital rocks to iron ore sinter particles (using filtered polychromatic X-ray beam). The paper is divided into three parts and includes: i) details on the methodologies including their benefits and limitations and the effect of spatial resolution; (ii) the quantification of pore network topology and pore characteristics (eg open versus closed pores, pore size distribution and pore morphologies; degree of connectivity of the pore network and its tortuosity); and (iii) the evaluation of the technique to characterise various phases within the material and quantify 3D mineral textures.CITATION:Godel, B, Ellis, B, O’Dea, D, Honeyands, T and Harvey, T, 2017. Digital rocks for iron ore sinters – towards a D quantification of sinter textures, in Proceedings Iron Ore 2017, pp 529–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Real Time and In Situ Measurement of Elemental Composition Using Lasers

Sep 13, 2010

By J Cornejo, A Pinochet, C Caviedes

The ore extraction rate and the incorporation of new areas are key operational parameters. In massive deposits mined by caving techniques they both control the cave back geometry, which is mostly responsible for the induced stress state around productive levels. Early detection of deviations from admissible geometries will prevent stability problems related to geomechanical hazards, helping to improve safety and working conditions and reduce the potential for lost reserves.This paper describes a mine planning tool currently in use at the El Teniente mine. This tool involves the control of the cave geometry based on rules that have been defined as a result of different studies and experience collected during the operational history of the mine.This mine planning strategy achieves an extractive mining process with lower risk than conventional planning methods, ensuring ore reserves extraction if followed as planned while reducing unexpected changes in mining sequences.CITATION:Cornejo, J, Pinochet, A and Caviedes, C, 2016. Geometric control for strategic mine planning at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The steps for the beneficiation of iron ores differ from ore to ore, depending on the mineralogical phases of the particular iron ore and the nature of the association of the gangue minerals with iron oxide in that ore. The extent to which the beneficiation can be undertaken economically depends both on the amount and the nature of the gangue. The analysis of the phases present in an orebody optimises the mining and process operations (separation, beneficiation, sintering, etc).X-ray diffraction (XRD) provides qualitative and quantitative information about the main ore phases as well as the gangue mineralogy and the amorphous content present in a sample. In addition, modern quantification methods such as Rietveld refinement allow the calculation of the distribution of elements in solid solutions such the substitution of Fe with Al in goethite or hematite.The use of high speed detectors has made XRD an important tool for grade and process control. Finger printing of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. Grade control using XRD can be completely automated and controlled remotely.The two case studies in this paper demonstrate how XRD and finger printing can be used for grade control, process optimisation and quality control of a goethitic and a magnetitic iron ore. The enormous potential of XRD as an inexpensive, reliable tool, useful in the characterisation of iron ores will be demonstrated.CITATION:K÷nig, U, 2013. Application of x-ray diffraction to iron ores - potential implications for grade control and downstream processing, in Proceedings Iron Ore 2013 , pp 275-280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Refractory gold ores have been the subject of intensive metallurgical study in order to achieve more efficient recovery of contained values and at the same time to minimise environmental impact. Considerable innovative gold processing technology was introduced in New Zealand last century, the most notable being the first successful commercialisation of the cyanidation process by the Crown Mines Company at Karangahake in 1889. The Karangahake gold-silver deposit was second only +to the Waihi Martha mine in total bullion production from the region with active mining from 1882 until about 1920 and sporadic production between 1930 and 1944. Reevaluation at Karangahake with associated metallurgical testing has continued since that time becoming particularly active in the last decade as a result of increasing gold prices. Gold processing technology is reviewed and results of some recent test work are presented and discussed in the context of Karangahake history and future development possibilities. This work confirms the variability and complexity of the Karangahake deposit both mineralogically and metallurgically and suggests flotation followed by new and innovative smelting is the most appropriate processing route for the recovery of gold from the high grade ore which could be produced from the Karangahake workings in moderate tonnages.

Jan 1, 1993

The whole of the iron ore required by the Broken Hill Proprietary Company Limited at the Newcastle Steel Works, and Australian Iron and Steel Limited, at Hoskins' Kembla Works, is drawn from the Iron Knob, Iron Monarch, Iron Prince and Iron Baron deposits situated in the northern part of Eyre's Peninsula, South Australia.The Iron Knob and Iron Monarch deposits are near the township of Iron Knob, approximately 42 miles W.S.W. of Port Augusta, whilst the Iron Prince and Iron Baron deposits are some 18 miles due south from Iron Knob, in another group of leases, the adjacent township being known as Iron Baron.The ore mined at Iron Knob, Iron Monarch, Iron Prince and Iron Baron is conveyed on the Company's 3ft. 6-in. gauge tramway to Whyalla, on the western side of Spencer's Gulf, approximately 45 miles south by west of Port Augusta whence it is shipped to Newcastle and Port Kembla.SHORT HISTORY.The establishment in South Australia of the lead smelting industry at Port Pirie, Dry Creek and Port Adelaide in the...

Jan 1, 1937

By S M. Iveson, K P. Galvin, D Kumar

Dry separation of iron ore fines and other heavy minerals has previously been achieved using one of two main approaches. The first is an inclined table with an upward airflow via small holes to help form an autogenous dense medium. The second is based on fluidised beds comprising a dense medium formed by fine particles suspended in an upward flow of air. In either case, vibration can be introduced. This paper describes recent findings using a novel system referred to as the Sink-Hole Fluidiser, which utilises elements of both these two former approaches. This device consists of a conventional gas-fluidised bed of fine medium with a 1 mm aperture mesh located at the surface. This mesh contains relatively large holes that act as sink-holes. The fluidised media flows upwards through the sink-holes and then falls back into the fluidised bed via the fine apertures in the mesh. The particles being separated, which are much larger than the fine media, pass over these sink-holes, where they either sink or float. The sink-holes offer a more precise balance of forces, applied on a single particle basis, resulting in robust density separation.Experiments have been performed using 2.0–4.0 mm tracer particles of density varying from 2.4 to 4.8 relative densities (RD) separated in a 200 mm diameter Sink-Hole Fluidiser with a single 13 mm diameter centrally-located sink-hole. In this preliminary semi-batch work, it was found that the Sink-Hole Fluidiser was able to achieve sharp separations (Ep as low as 0.20). This work underpins the development of a new continuous steady-state Sink-Hole Fluidiser, applicable to the dry separation of iron ore fines.CITATION:Kumar, D, Iveson, S M and Galvin, K P, 2017. A novel sink-hole fluidisation method for dry separation of iron ore fines, in Proceedings Iron Ore 2017, pp 221–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Approximation of Surface Area of Fines in Blast Induced Fragmentation The surface area of fragmentation, especially in the finer size fractions, is a useful property to characterise the mechanisms of rock breakage. In the past, researchers have made assumptions with regard to the shape of fragments in order to estimate surface area, such as that all fragments are the same shape or all fragments are spheres. Often these assumptions were developed with inappropriate measures and returned considerable variability and error for the calculation of surface area. This paper reports a model to estimate fragmentation surface area from sieve sized raw data and a density measurement, with experimental validation down to a size fraction of -45 + 38 ?m in a range of rock types. After characterisation of particle shape, a range of fragment shapes was found to be in each size fraction. Nevertheless, in the ?2 sieve series the average fragment mass, volume and the size fraction standard deviations could be predicted reasonably accurately. Ellipsoid geometry was used to describe particle shape. Using these parameters and the number of fragments (also predicted) in each sieve size the individual surface area of each fragment was simulated.

Sep 13, 2010

The project to reopen the Tasmania Mine has centred around efforts to reopen the Hart Shaft to access the high grade reef remaining below the old workings, which extend down to 457 in. Efforts in 1982 and 1987 were frustrated by unstable clay ground around the shaft, which resulted in significant subsidence of the shaft collar and lining. A successful program has since been implemented to solve the problems, stabilize the collar and recover the upper shaft which had collapsed down to 90 m.

Jan 1, 1989

By Lancucki C. J, Nickson N. M

X-ray diffraction and differential thermal methods were used to determine the mineralogy of some clays used by the heavy clay industry in the Adelaide area. A detailed analysis was made of the mineralogy and particle size distribution of eighteen samples from beds in two pits in the Recent sediments in the Adelaide plains, of six white clays developed from the weathering of the Adelaide series of sediments, and of four Recent alluvial clays from a pit in the Mount Lofty ranges south of Adelaide. Structural clay products in the Adelaide area are manufactured from mixtures of these clays, so the mineralogy and particle size distribution was determined of eighteen clay mixtures used to make red bricks, cream bricks, facing bricks, pipes and tiles.Knowledge of this mineralogy is important in understanding the ceramic behaviour of the clays.INTRODUCTIONIn this investigation an account is given of the clay mineralogy and particle size distribution of some ceramic clays from the Adelaide area. The clays are used in the manufacture of structura,l clay products and the results to 'be described are part of an overall 'plan of study covering the heavy industrial clays and shales of Australia. Previous work has been published (Cole and Carthew, 1953; Ferguson, 1954; Ferguson and Hosking, 1955; Cole and Nielsen, 1958/59).In this work no attempt has been made to examine clays from all pits engaged in supplying materials for the structural clay industry. However, in 1954 the senior author collected detailed samples from two pits working in Recent alluvial clays in the Allenby·Gardens and Beverley areas near...

Jan 1, 1963

The object of this paper is to give a description of the new office and changehouse building and equipment at the Zinc Corporation Limited, the office section of which has now been in full use for approximately three years, and the changehouse section for approximately two years. As the expectations of the design have been fully realized, it is thought that this description will be of interest to members and possibly of some use to others faced with similar problems.GENERALIn the centralization of the surface plant around the new main shaft the combined office and changehouse building forms a prominent feature, being located between the shaft and the mill and facing the workshops on the northern side.The scheme for housing all employees in one building was proposed by the Manager, Mr. A. J. Keast, who was familiar with a similar successful structure built at the McIntyre Porcupine Mines Ltd. in Ontario, Canada.The principal features of this building were adopted as a basis for design, and the present layout evolved to suit the particular requirements of this mine.Some of the advantages of the design are:(a) Economy in first cost and space occupied when compared with plants having separate office and changehouse buildings.(b) Easier and more constant supervision of employees and of the plant by the senior staff members.(c) Close contact between officials of all departments.(d) Close covered connection between changehouse and shaft.(e) Avoidance of duplication of ,essential services such as electric power, water, heating plant, sewerage, etc.The Managing Director, Mr. W. S. Robinson, further instructed that the following requirements be adhered to in the new building:(a) Ample accommodation to be provided for office staff and other employees.(b) Special attention to be paid to lighting, both natural and artificial.(c) Working temperatures to be controlled to facilitate comfort and efficiency.(d) The buildings and equipment' to be of a permanent nature with furnishings and fittings of modern design.

Jan 1, 1941

Upgrading and Removing Phosphorus from Low-Grade and High Phosphorus Containing Iron Ores

Sep 13, 2010

By C S. Szentesy, K Howie

The Rosia Montana gold deposit is located within the æGolden QuadrilateralÆ area in the Apuseni Mountains of Transylvania, Romania. The deposit is situated approximately 85 kilometres north of the regional centre of Deva, within the province of Alba, at elevations of up to 1100 metres above sea level. The Rosia Montana deposit contains a current resource of 344.07 million tonnes at an average grade of 1.3 grams per tonne (g/t) gold (Au) and 6.0 g/t silver (Ag) for a total (measured, indicated and inferred) contained resource of 14.29 million ounces of gold and 67.00 million ounces of silver. The resource was calculated using a 0.6g/t Au cut-off, a 10 x 10 x 10 metre block size and multiple indicator kriging. The low sulfidation style epithermal mineralisation at Rosia Montana is hosted within Tertiary age dacite intrusions and related vent breccias. Mineralisation is generally disseminated and associated with silica, adularia, illite, pyrite and carbonate alteration of host rocks, with minor late carbonate-base metal veins. Precipitation of precious metals is generally considered to have occurred as a result of over-pressurization, boiling and subsequent brecciation. The dacite intrusions are hosted in Cretaceous shallow marine and deltaic shales and slates, which overlie older Paleozoic sedimentary and metamorphic rocks within uplifted sections of oceanic sea floor.

Jan 1, 2002

The corrosion of aluminosilicate refractories by soda from three different sources has been studied by microscopic methods. Sodium sulphate from oil ash, sodium chloride used in glazing structural clay products, and sodium borate from borax-impregnated wood ash have fundamentally the same effect on the refractories. The soda is the chief medium of reaction and fluxing, the sulphur, chlorine, and boron being volatized as sulphuric, hydrochloric, and boric acids.INTRODUCTIONBecause of their strong fluxing action, alkalis are one of the main causes of corrosion and slagging of refractories.The action of potash and soda on refractories follows somewhat similar lines, although it is common for one alkali to be greatly in excess of the other. The course of the reaction in a number of cases of alkali attack has been studied by microscopic and chemical methods. For example, the action of potash on blast furnace refractories was studied by Kraner (1942) and Rigby and Richardson (1947), who described the occurrence of various potassium aluminium silicates. Its action on cement kiln refractories was described by Brisbane, Segnit, and Weymouth (1957). The action of soda on glass tank refractories has been studied by many people, for example Bisby (1956) and Resch (1954). Clews, Hugill, and Green (1940) made a microscopic examination of the attack by soda on silica bricks from a gas retort.Some recent cases of corrosion of aluminosilicate refractories which were brought to the attention of the Division of Building Research, C.S.I.R.O., illustrate phenomena which occur under conditions different from those...

Jan 1, 1964

James Barnes is Managing Director of James Barnes & Associated Ltd which is a company that has invested ten years of development to provide developers with a transparent, user friendly consultation framework that identifies who needs to be consulted, how they are to be consulted and procedures required to manage the risks associated with getting all the wrong! Despite the assertion above, this paper is not about to provide delegates with the answer to whom they ought to consult or identify the expectations that Maori might have in regard to the consultation process. It would be a very brave person indeed who would venture an opinion on such a sensitive subject. There are no short cuts to finding out what expectations Maori might have on any given situation. Nothing can be taken for granted. What this paper will attempt to do however is provide practical insights into what might be on the minds of Maori interests as they deal with the issues associated with mineral resources, particularly those under Treaty of Waitangi Claim. The Treaty of Waitangi has a significant bearing on the current debate between Maori and the Crown regarding ownership of mineral resources in New Zealand. The Waitangi Tribunal is currently hearing a case presented by a number of Iwi over the ownership of oil and gas resources in Taranaki and Hawkes Bay. Others will follow. The Crown and Maori have never been able to settle differences over ownership rights without resorting to legal action and it looks like this scenario is about to be repeated in regards to minerals. The Crown has a duty to actively protect the Maori interest. This is a fundamental expectation in the relationship between Maori and the Crown. In the case of minerals, Maori have yet to see the Crown do its duty. The impact on developers has become evident through Maori objections to consent applications as the issues of mineral right remain unresolved.

Jan 1, 2000

By R Dwyer, S Rea, W J. Bruckard, N McSweeney, R Holmes

"The innate ability of microorganisms to adapt to changing or inhospitable environments has often been exploited for industrial purposes and forms the basis of many current biotechnological processes. The ability of bacteria to adapt and adhere to specific mineral surfaces ensures that the energetic or nutritional requirements of the cell are met and often serves as a survival mechanism under unfavourable?growth conditions or conditions of stress. In this process, cells may rearrange or modify the macromolecules expressed on the cell surface itself or produce extracellular molecules, modifying mineral surfaces to render them more suitable for growth. The modifications that these molecules produce on mineral surfaces may result in changes to the surface charge and hydrophobicity of a mineral. As a result, these biomolecules may have some potential application as flotation collectors or modifiers.In this work, the effect of long-term exposure of Paenibacillus taiwanensis to goethite and common gangue minerals associated with Australian iron ores on the differential expression of membrane and extracellular proteins was determined. Both groups of proteins play a role in cell adherence to mineral particles. Cells were adapted to grow in the presence of each mineral over time. The proteins expressed on the cell membrane and the extracellular proteins excreted by the cell were isolated and analysed by two-dimensional polyacrylamide gel electrophoresis (2D gel PAGE). The outcomes of these studies are presented here and potential application of these products for flotation discussed.CITATION:Dwyer, R, Rea, S, McSweeney, N, Bruckard, W J and Holmes, R, 2013. Microbes and their metabolites - potential iron ore flotation reagents, in Proceedings Iron Ore 2013, pp 369-372 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013