Search Documents

By Moorrees C

Tests show how that temperature and rate of sparging to remove carbon dioxide determine the rate of precipitation and the chemical and physical properties of hydrated magnesium carbonates precipitated from clarified magnesium bicarbonate liquors derived from crude magnesia. At temperatures above 55°C the product is largely in the form ofhydromagnesite, Mg5(C03)4(OH)2.4H2O Between I5°C and 55°C the major product is nesquehonite, MgCO3·3H2O, although partial hydromagnesite precipitation can be induced by a high rate of aeration.As a result of the reduced time required to bring about greater than 95 per cent magnesium precipitation, the higher MgO content of the product, the ease of product recovery from the precipitation vessel, and the lower energy requirement for thermal decomposition of the precipitate to magnesia, it is preferable to precipitate hydromagnesite rather than nesquehonite. Moreover, the magnesia produced from hydromagnesite is somewhat more reactive than that formed from nesquehonite.Using precipitate calcination temperatures less than 1000°C, the chemical reactivities of the magnesias formed from both precipitates are greater than those of the crude magnesias derived from Savage River magnesite itself. The magnesias would be suitable for most uses developed for caustic-calcined magnesia. However, for refractory brick manufacture, it would be necessary to briquelle the caustic-calcined magnesia. adjust the CaO and SiO2 contents and sinter at temperatures in excess of 1600°C. This would bring about an increase in the bulk density and induce the appropriate chemical bonding reactions.Dead-burned magnesia produced from Savage River magnesite by the calcination/carbon dioxide route would have very low B2O3 contents, typically less than 0.0001 per cent.

Jan 1, 1985

By Whiten WJ, Narayanan S

Data from ball mills of a wide range of sizes are analysed using detailed mathematical models and non-linear least squares fitting techniques. This analysis reveals that the relative power inefficiency of large ball mills is due to inefficient grinding of coarse (plus 4 mm) particles in these mills. A qualitative physical hypothesis is proposed to explain this behaviour. The results of the analysis can be used to scale up ball mill behaviour, using the mathematical models and techniques developed. A simpler ball mill scale-up procedure is also proposed, and its limitations stated. Laboratory experiments are being conducted to determine the average size distributions of single particles of different ores after breaKage. These experiments can distinguish between the different ores, and it is hoped to use their results to model and predict the grinding of different ores in ball Mills.

Jan 1, 1978

By Corbett GJ

Comparisons between individual SW Pacific Rim gold deposits have facilit-ated proposal of a new classification of porphyry-related mesothermal gold deposit types. Carbonate base-metal gold systems form at relatively high crustal levels, peripheral to porphyry intrusions. There is a spatial assoc-iation with major structures which focus fluids from degassing porphyries at depth. Milled matrix intrusive breccias and extrusive maar volcano/ diatreme breccias form as a result of pre-mineralisation phreatomagmatic eruptions. These focus degassing magmatic fluids by the provision of fracture ground preparation, typically within competent host rocks, adjacent to the breccia bodies. Local dilational structures control the form of individual deposits which may contain bonanza gold grades at sites of fluid quenching and/or repeated mineral deposition.Early quartz veining and porphyry-related alteration is common and later gold mineralisation typically occurs in association with carbonate veining and Fe and base metal sulphides as Zn > Pb > Cu. The progressive cooling by mixing of the upwelling mineralised magmatic fluid with descending bicarbonate waters, produces characteristic zonations in carbonate compositions. These vary with distance from the porphyry source, from Ca through Mg, Mn and distal Fe types. Gold mineralisation is preferentially distributed within the Mn/Mg carbon-ates.

Jan 1, 1994

1880 - 1930 - The Golden Years of Mineral Processing Technology

Sep 13, 2010

By Olson H, Kincaid R

The marine portion of the Pacific Basin and Rim constitutes a significant part of the world's surface in which the mineral resources are virtually undeveloped. Indications of substantial resources have resulted in speculation and uncertainty with regard to their potential in the near term. The main issues are centered on the markets for the resource materials, the technology needs for their recovery, and the possible impacts of their development on the environment. While the governments of Japan, France, the Soviet Union, India, China, and Korea are financing new programs in deep ocean mining, the US is consolidating its early leadership by the continuation of NOAA's authority under the Deep Seabed Hard Mineral Resources Act and the Sea Grant Act, Interior's authority under the outer Continental Shelf Lands Act, and by the development of a new Marine Minerals Technology Center within the Department of Interior's mineral institutes program, managed by the U.S. Bureau of Mines. The Center has a Continental Shelf Division (CSD) located in Mississippi, and an Oceans Basin Division (OBD) located in Hawaii. Research and training in the divisions is directed toward the practical aspects of mineral recovery from the nearshore and deep ocean environments with a strong bias for the OBD toward industrial and international cooperative programs in the Pacific Basin and Rim. In terms of resource development, the marine minerals in the Pacific Basin may be favored in some cases, in competition with land sources, by political and environmental considerations.

Jan 1, 1990

By Hoppe AJ

Drilling and shooting techniques at Moura open-cut have evolved over a period of 16 years and are the result of hard earned experience combined with established practices and consul- tation with professional services. The wide range of overburden types encoun- ted in the field requires varying methods to achieve the best results at all times. Safe working conditions for the employees and protection of mining equipment is of para- mount importance and close liaison is maintain- ed with the Department of Mines Queensland to keep abreast with changing legislation. Drill patterns, charging profiles, types of explosives and ultimate results are des- cribed in detail along with a resume of equip- ment. Costs of drilling, labour and explosives are also analysed with a total of approximately 20c per cubic metre of shot ground. Future developments and improvements to facilities are also outlined.

Jan 1, 1978

By Dimitrakopoulos R

Ore textures in base metal deposits are an important factor in the liberation of the economic components of the ore, metal recovery and reagent consumption during beneficiation. Optimising the mine profit requires knowing the relationship between ore texture and mineral processing behaviour, and the ability to predict the metal grade and the ore texture at a suitable scale. A new method that generates distributions of mesotextures for any mining block size or shape is proposed and includes: I . establishing a protocol for acquiring mesotexture data: 2. measuring the mesotexture spatial correlations using a multi-texture variogram; 3. generating multiple simulations of mesotextures; and 4. upscaling the simulations to generate the expected mining block/stope mesotexture distributions. Models of the ore textures built using the proposed methodology can be used to assess resources and reserves, enhance ore/waste discrimination and predict the metallurgical behaviour of parcels of ore.

Jan 1, 1997

As part of its Concentrator operation Hamersley Iron Pty. Limited uses wet high intensity magnetic separation to upgrade shaley low grade ore in the minus 0.5mm size range. Materials handling problems, largely caused by fine ore types and design deficiencies, surfaced in the Fines Treatment Plant soon after Concentrator commissioning in 1979. Surging throughout the circuit impaired process efficiency and added to problems caused by capacity and process control limitations. In 1981 extensive modification works were initiated to supplement minor changes made to that date. The new circuit significantly increases capacity and provides greater process control.

Jan 1, 1978

In a high pressure rolls crusher two force components: the pressurising thrust and the rolling force can be measured experimentally. Computer analyses have revealed regular patterns of stress distribution in the confined material between the rollers. Based on the computer analyses and experimental results a one-dimensional comminution model has been developed.

Jan 1, 1995

By Pilkington T, Noy A

The Yallourn North Extension (YNX) open cut mine ceased mining operations in early 1989. YNX may be used again for coal supply at the discretion of the Coal Corporation Of Victoria (CCV); this has resulted in the need for interim rehabilitation of the site which may last many years, or indeed, permanently.The site has suffered substantial surface erosion over the years with large areas of bare clay and coal batters remaining exposed. The first priority is to reduce the quantity and improve the quality of stormwater runoff from the site. This is best achieved by appropriate revegetation and the use of existing landform depressions as silt trap/wetland areas. Proposed rehabilitation needed to take into account the sensitive fire safety of the open cut and the option to re-open the mine if CCV deems appropriate.The authors detail the factors involved in the rehabilitation proposal and the multi-disciplinary approach to planning including engineers, scientists, a forester, landscape architects and community input. The rehabilitation design included early consideration of land use and ongoing maintenance issues linked to water quality improvement factors including vegetation. Engineering input was required for reshaping and clay covering exposed coal batters and the design of silt traps which will revert to wetlands in future. The integration of each discipline has produced a rehabilitation design pleasing to both the SECV and community alike.

Jan 1, 1992

Revised throughput rates, as a result of current mining methods and tight controls on mine dilution, have dictated a change in metallurgical philosophy at Renison Limited. Emphasis on throughput capacity increases has altered to a reduction in circuit complexity and operating costs. Extensive surveys of the gravity and cassiterite flotation circuits led to several plant modifications between August 1989 and March 1990. The coarse and fine gravity retreatment roughing tables were by-passed, the coarse gravity retreatment roughing tables were re-commissioned, the cassiterite flotation rougher capacity expanded and the gravity regrind cyclones re-configured.

Jan 1, 1991

By Moore A. J

This paper describes the use of a wavefront reinforcement model which has been developed to supplement established charge mass scaling methods. The model allows for the time taken for blast vibration wavefronts to travel from each blasthole, and has been successfully used to explain the reason for directional increases in both air and ground vibration in certain situations. The model has been used to identify wavefront reinforcement due to the propagation of air vibration and ground vibrations in certain situations. The paper includes a throw (or cast) blasting case history which provides multi-station evidence of the strong directional nature of wavefront reinforcement.

Jan 1, 1995

By Harris RW, Wood BR

At any given time, the tidal force subjects massive regions to a spatially uniform load. The deformation of any large structure due to these forces is proportional to the elastic properties of the structure. In this aspect, the tidal force applies a load in a manner similar to that of a large-scale testing machine. Any anomalies in the measured tidal response must reflect alterations in the average elastic response of the massive structure. In the present work, tidal tilt measurements obtained in the wall of a large dam are used to infer changes in the response of the dam to applied loads. In particular, it is found that the dam response has changed by approximately 13 percent, on average, for two monitoring periods separated by 5 years. It is possible that these changes were produced by the different volumes of water in the dam for the monitoring periods. The tidal measurement technique can also be applied to monitor changes In the average structural response of large underground and surface masses relevant to coal and metal mines.

Jan 1, 1992

By D A. Kepert, D Clark

During early 2004, Fortescue Metals Group (FMG) began an aggressive exploration and drilling program in the Chichester Range, targeting iron enrichment developed in the Nammuldi Member at the base of the Marra Mamba Iron Formation. The timely recognition by FMG of distinct zones of (hypogene) microplaty hematite (mplH) enrichment overprinted by extensive supergene mineralisation led to an early reappraisal of the geological history of the area and characterisation of the possible structural and stratigraphic controls on mineralisation. Regionally, the Chichester Range dips gently at less than 5¦ to the south, however, detailed mapping shows that this regional limb is overprinted by low amplitude, long wavelength, north/south to northeast/southwest trending folds. The locations of major structures in the Marra Mamba Iron Formation, combined with spectral analysis of known mineralisation, allowed extrapolation and prioritisation of exploration target areas. The delineation under cover and understanding of these structures was enhanced by detailed airborne magnetic data. Recognition that supergene mineralisation was associated with a palaeotopography that continued significantly under cover to the south under sediments of the Fortescue River valley led to the discovery of extensive supergene mineralisation together with additional mplH mineralisation. A model for the landscape evolution and preservation of enriched Nammuldi Member was generated in order to help communicate both the complexities involved with targeting drill holes beneath cover and the potential limits to the lateral extents of mineralisation.

Jan 1, 2005

By Bromley JC

Eimco Great Britain, a division of Baker Mining Equipment Company, was contracted to develop a hardrock tunnelling machine in conjunction with British Coal. The objective: a machine to cut rock up to 170 MPa compressive strength yet retaining the flexibility of roadheader type machines. This flexibility to encompass mobility, wide range of excavation shapes and sizes, simplicity of design and use, compact size, and efficient cutting operation. Current roadheaders operating in hard material are characterized by: 1. Severe machine vibration 2. Bouncing of the boom away from the rock 3. Very high pick wear 4. Inability to sump head in bad floor conditions The reasons for this poor performance can be attributed in part to: 1. High speed of cutting head rotation 2. Inability to hold boom against rock while cutting variable hardness strata. To overcome the problems described, a new articulation method was developed utilizing four hydraulic rams to "lock" the boom in position on one axis and four hydraulic motors to rotate the boom for cutting via a turret arrangement. The slide mounted turret is hydraulically advanced for sumping into the face, independent of the machine base. To transfer cutting forces back to the rock, the machine base is held rigidly in the excavation by floor to roof or side to side rams. A cutting head mounted on the boom rotates at very low speed, but with very high torque.

Jan 1, 1987

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

By Chappell B

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to he placed in a tailings darn. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electro- osmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By Y K. Leong

Occasionally additives are used in the wet processing of iron ore tailings and slurries, for examples, in the thickening of tailings with flocculant to recover process water, and in the smooth pumping of concentrated slurries. They can mitigate slurry behavioural issues that could significantly affect the plant operation and production. The nature of iron ore business requiring the plant to have a high throughput to be economical, large amounts of slurries are therefore processed every day. The quantity of additives needed will correspondingly be large and so are the associated costs. This could have a significant impact on the plant profitability. If additives are used they must be very costeffective. NaOH is among the lowest cost chemicals available, at ~US$400 per ton. In this paper we will look at use of composite additives involving phosphate compounds with NaOH added to reduce the cost, for the control of iron ore slurries rheology. The NaOH worked synergistically with the phosphate compounds. The effectiveness of these composite additives in viscosity reduction can be neutralised by another cheap additive such as lime or a Ca(II)-based salt turning the slurries back to being a paste. Tailings paste is an ideal material for safe storage in the dam. These composite additives can also be used to facilitate the recovery of iron ore at commercial grade from tailings (Leong, 2020a, 2021a).

Sep 18, 2023

By Giles D, Wegmann D

The Mt Todd Gold Project is located 42 km northwest of the township of Katherine within the Northern Territory of Australia. It is situated in the southeastern portion of the Pine Creek Geosyncline. The Batman gold deposit, the largest of several deposits at Mt Todd, hosts an identified mineral resource of 92.9 million tonnes (Mt) grading 1.4 grams/tonne (g/t) as at 31 December 1993. Host rocks at Batman are assigned to the Early Proterozoic Burrell Creek Formation, comprising greywacke and siltstone interbedded with shale. Gold mineralisation is associated with a very broad zone of sheeted and stockwork quartz-sulphide veins that occupy a corridor of intense brittle fracture and faulting. A conceptual model of formation involves the dilation of joints and micro-faults within overlying sediments during sinistral movement along a basement shear zone. Synchronous granite intrusion generated convective circulation of crustal fluids through the sedimentary pile resulting in the formation of auriferous quartz veins within favourable structures. The Batman zone of mineralisation is not directly related to fold structures which typify several other major gold deposits within the Pine Creek Geosyncline.

Jan 1, 1994

By H S. Smit, P Lotz

Gold mining companies who are signatories of the International Cyanide Management Code (visit www.cyanidecode.org for further information) are required to measure WAD cyanide on-line and destroy WAD cyanide in excess of specified limits. Weak acid dissociable (WAD) cyanide refers to those cyanide species liberated at a moderate pH of 4.5 such as HCN(aq) and CN-, and the majority of Zn, Cd, Cu, Ni and Ag complexes with low dissociation constants. It is potentially toxic to humans and animals. Recognising and in response to the gold mining industryÆs need for an on-line WAD cyanide measurement device, Mintek recently developed the WAD Cynoprobe. The WAD cyanide analysis technique is based on the use of a ligand exchange reagent that liberates WAD cyanide from metal-cyano complexes. The ligand exchange reaction is represented by the following chemical equation: Metal(CN)X + yLigand <-> Metal(Ligand)y + xCN- The plant filtrate is treated with a ligand exchange reagent, to liberate WAD cyanide, before measuring the free cyanide concentration via amperometry. The instrument proved to be accurate and reliable in the laboratory as well as under industrial gold plant conditions during various trials. It has gained wide-spread commercial acceptance both locally and internationally. However, itÆs recent exposure to complex ore types have called for refinements to the analysis technique. It has been further developed to improve its precision and accuracy and to remove reagent and thiosulfate interferences. Its compatibility with the most commonly used destruction oxidants has also recently been investigated. The WAD Cynoprobe may be configured to measure both free and WAD cyanide concentration. Its fast analysis time, approximately 5 min, makes it suitable for use in the control and optimisation of the cyanide destruction and recovery process. Proper oxidant dosage control and monitoring of effluent concentration levels will ultimately result in less cyanide and post-destruction salts discharged into the environment.

Jan 1, 2008