Search Documents

Upgrading of Indonesia's Bauxite by Washing Method There were eight bauxite samples used in this research, three samples from Kijang contain total SiO2 18.36 - 29.16 per cent, Al2O3 40.12 - 48.36 per cent, Fe2O3 4.27 - 5.13 per cent, one sample from Tayan, contains total SiO2 4.69 per cent, Al2O3 38.95 per cent, and Fe2O3 19.67 per cent, and four samples from Mempawah contain total SiO2 33.5 - 44.8 per cent, Al2O3 29.8 - 35.9 per cent, Fe2O3 7.29 - 9.88 per cent. All of those bauxite ores have not fulfilled the requirement for Bayer process yet; therefore simple up-grading using a rotary drum scrubber is needed. The scrubbing process was carried out with time variable up to 60 minutes with solid percentage applied was 50 per cent and rotary speed was set up 30 rev/min. The bauxite was washed by following steps: scrubbing, screening, drying, and finally it was analysed to show chemical content. The washed bauxite produced has size fraction that is retained on the 1.7 mm of screen opening. The result of the research shows that the higher alumina content of the raw bauxite, the longer washing time is needed moreover the higher quality of the washed bauxite is produced. The highest alumina content of the washed bauxite was 53.67 per cent with the alumina recovery was 89.66 per cent and the concentration ratio of 84.80 per cent was achieved within 20 minutes of washing time of the raw bauxite (Al2O3 48.36 per cent). The washed bauxite resulted from this research is suitable as a raw material for Bayer process.

Sep 13, 2010

By V O’Brien

The suitability of magnetic surveys flown at low altitudes to identify buried heavy mineral (HM) strands has long been accepted. This is despite the low intensity magnetic response often obtained from such strands. The fundamentals of the magnetic survey method dictate that the closer the instrument is to the source the stronger the response. As such the optimal elevation for the magnetometer is at or near the surface. Iluka sought to use a ground based magnetometer to aid in the exploration target generation process and allow accurate targeting of exploration drill holes. Following the initial trial Iluka recognised the potential additional application of data obtained by a ground based magnetometer over known strand deposits. The detail of the ground magnetic images can confirm the assumed strand continuity between cross-sections of close spaced drilling and can aid in the definition of the geometry of different generations of mineralisation. The ability to confidently determine that the deposit has not been truncated by post emplacement erosion of the mineralised deposit may enable reductions in drilling requirements as well as assisting mine planning activities. Iluka intends to investigate advanced modelling of the magnetic data to determine the level of strand geometry and HM content resolution that can be achieved from the ground magnetic survey data and its potential application in the mining grade control process.It is anticipated that the surveying of Iluka’s known resource deposits will provide the ability to correlate the magnetic response from new exploration targets with those from known deposits for a given depth, HM grade and mineralogy suite.

Oct 5, 2011

By D Giddings, S A. Silvester, S Pickerin

Underground fires represent a constant threat to the safety of underground personnel. Miners in the immediate vicinity may face intense heat, blinding smoke, toxic fumes, fall of ground and other direct effects of a fire. However, the vast majority of victims never actually see the fire, and are overcome either by deadly fumes in the ventilating current or by asphyxiation. The mine ventilation system, which maintains a sustainable atmosphere to the working places, can transport products of combustion with equal efficiency. Miners who are remotely situated from a fire may be forced to evacuate considerable distances, through dense smoke and fumes, or even become cut-off from escape. Additionally, miners may become confused by unfamiliar ventilation characteristics caused by fires. Conveyor belts are widely used for transporting minerals in mines as well as in many other industrial situations. Because they contain large amounts of polymeric materials their use in certain environments, especially coal mines, but also in steel works, power stations and other enclosed areas must be controlled to minimise the fire risk. Over last nine years there have been 60 fires in underground mines in the UK alone and that of these, half have been associated with conveyors. This paper summarises the results obtained from a recent research project that has developed a preliminary computational thermal and fluid dynamic model to represent the spread of flame along a typical conveyor belt used in UK deep coal mines. The results of these models have been calibrated against a series of experimental tests performed within a surface fire test gallery. An improved knowledge of the burn characteristics and rate of release of the products of combustion from conveyor belt fires will assist in the development of better fire detection and fire fighting techniques.

Jan 1, 2005

By A Tsoy

This abstract describes long-term mining schedule optimisation approach that may be suitable for complex marginal projects and is based on modern scheduling techniques. CITATION: Tsoy, A, 2018. Strategic mine schedule optimisation, in Proceedings Complex Orebodies Conference 2018, pp 91–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A Vakili, F Harvey, H Greaves

Mine seismicity is one of the most difficult geotechnical risks to manage in seismically active mines. There are currently some established empirical and statistical methods that provide quantitative measures for seismic hazard assessment in operating mines. However, these methods are mostly suitable for quantifying the current or historical seismic hazard and often cannot be directly used to forecast the future hazards. Numerical modelling is the only analytical tool that can capture the level of complexities required for a meaningful analysis of mine seismicity and therefore to facilitate a reliable forecast of future hazards. However, there is currently no widely accepted and established guideline and methodology for analysing and forecasting mine seismicity using numerical modelling. This paper first provides a background on previous published studies on this subject and then outlines the key aspects that can affect the reliability of the forecasting for mine seismicity. These aspects include a) processing of historical seismic data, b) selection of suitable numerical modelling approach, c) Post-processing and interpretation of the model outputs. A case study is then presented for the Gwalia Deeps Mine where a new framework was developed to forecast future mine seismicity. High-quality seismic data for a period of five years was used for back-analysis and comparisons with the numerical modelling outputs. After development of the method, the future seismicity was forecast for the next 12 months and the actual seismicity was monitored against the forecast during this period. Results of this study shows promising potential for the proposed framework to be applied more routinely and at other mine sites. However, more validations are required at Gwalia Deeps mine as the mine proceeds to deeper levels. In addition, the method needs more improvements and should be tested and validated at other mining operations before it can be established as a proven method. CITATION:Vakili, A, Harvey, F and Greaves, H, 2018. Forecasting mine seismicity – towards a more established methodology, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 207–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By T Baumgartl, B Richards

The association of specific plants and plant communities with soils developed over underlying superficial orebodies and mineralisation has been long recognised. It has given rise to the use of plant indicators for geobotanical exploration as a regular component of primary minerals reconnaissance where there is an undisturbed vegetation cover. That the chemical composition of indicator plants is a measure of their soil environment has further led to biogeochemical prospecting methods for minerals and its use in the mapping of underlying ore deposits. Where there is a strong surface expression of metal and metalloid anomalies, concentrations of potentially phytotoxic elements may reach a level at which they have strong selective impacts on plant populations. In such circumstances, natural selection has operated in the development of a unique flora composed of plant species and individuals with genetically-based tolerances to the stressed environment in which they continue to survive. These plants are called metallophytes. Metallophytes occur globally on all metalliferous sites, both in pristine undisturbed environments and in areas of mineral workings, ancient and modern. However, the best-developed primary metallophyte vegetation is found in the most ancient areas where there has been a long-term evolutionary impact of the underlying geology through ore weathering and dispersion of metals into the rhizosphere zone. Natural selection of metal-tolerant races of plants in these largely undisturbed areas can eventually lead to speciation and the development of an endemic regional metallophyte flora (Baker et al , 2010). Mineral wastes resulting from mining activities also allow colonisation by metal-tolerant individuals leading to the establishment of metallophyte communities. The distribution and extent of such communities is determined by regional and local factors relating to climate and substrate conditions and the availability of suitable plant resources on which natural selection can operate (Baker, 2009).The ability of metallophytes to tolerate extreme metal concentrations commends them as the optimal choice for ecological restoration of mineral wastes and metal-contaminated sites. Metallophytes have recently also spawned several novel phytotechnologies, including phytoremediation and phytomining (Chaney et al, 2000, 2005; Baker and Whiting, 2008). Action towards conserving the global metallophyte resource base is imperative because many species are under threat of extinction from new and extensive mining activities (Whiting et al, 2004). This has been identified as a priority in the Mining, Minerals and Sustainable Development (MMSD) Project of the Global Mining Initiative in 2002 but positive responses from the minerals industry have been slow. The last decade has, however, seen an ever-increasing interest in metal-tolerant and metal-accumulating plants, both from an academic standpoint and their use in revegetation and phytostabilisation (Tordoff et al, 2000; Baker and Whiting, 2008; Baker, 2009). Few studies have highlighted the need to conserve and develop these unique plants (Whiting et al , 2004). This presentation identifies future research needs for the conservation and exploitation of the global metallophyte biodiversity and its potential in sustainable mine closure. CITATION:Baumgartl, T and Richards, B, 2012. Evaporation and salt transport under variable climatic conditions, in Proceedings Life-of-Mine 2012 , pp 179-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

Sishen uses a state-of-the-art tracking system to track material from its position in blast blocks through various stockpiles and crushers. Qualities are blended directly to the crusher as opposed to blending from stockpiles. This poses an interesting challenge to the planning department to simulate these conditions. The software used in these simulations are Whittle 4X and Maximiser for long-term planning, Xpac for medium-term planning and Mine Works Planner for short-term planning. Geological models and mine design layouts utilise Surpac. Sishen introduced Xpac a number of years ago; the system has developed and changed over the years. With the Sishen Expansion Project (SEP), which aims to utilise low-grade material, major changes to the planning process have to occur. SEP requires that the mine have two different plants, which utilise two different ROM feeds and have different beneficiation curves. Xpac is used to produce a rolling 18-month plan, which is as close to actual operations as possible. In order to do this, the simulations have to take into account the plants beneficiation curves, stockpile movements, hauling distance and equipment needs. On top of this, the schedule has to continually consider specifications for Fe and the contaminants. Plant yields also have to be kept within a certain bandwidth. Xpac is used to simulate the above parameters, as well as generate the raw data required to produce a mine budget. The paper will also show how the 18-month planning process and subsequent planning processes are measured and aligned. Xpac has proved to be an excellent tool to achieve these goals.

Jan 1, 2005

By B N. Noller, J C. Ng, S L. Bruce

Mining activities can result in the transfer of harmful elements, including arsenic and lead, into the environment. In Australia, one of the potential future uses of rehabilitated mine land is to stock grazing animals. Elemental uptake is dependent on bioavailable fraction for adsorption upon exposure. Bioavailability data are generally lacking in order to provide realistic health risk assessments relating to harmful elements from mine tailings in Australian conditions. Another key component of risk assessment is the ability to estimate a realistic exposure, or dose rate, of the tailings to the grazing cattle over a set period of time. Hence, we aimed to conduct grazing trials directly on rehabilitated tailings facilities in order to provide valuable in situ information on heavy metal dose rates and associated accumulation. For the laboratory-based evaluation of comparative bioavailability, groups of cattle were fed five days a week on a normal diet spiked with mine tailings or soluble pure salts of target elements (eg sodium arsenate, sodium arsenite and lead acetate) for about eight months. For the field validation, cattle were allowed to graze directly on rehabilitated tailings facilities over a similar length of time. Blood and a biopsy of the muscle and liver were periodically collected to monitor arsenic accumulation. At necropsy, blood, muscle, liver, kidney and other saleable tissues were measured for arsenic concentrations. Although this study was focused on arsenic, lead and other metals were also measured. Predictive models for arsenic and other metals have been established to calculate the maximum grazing duration without the risk of exceeding specific food safety guidelines. The outcome of this study is a predictive model for maximum beneficial use of certain rehabilitated tailings for cattle grazing where grazing activities do not impact on the integrity of the tailings dams.CITATION:Ng, J C, Noller, B N and Bruce, S L, 2014. A predictive model for beneficial use of rehabilitated mine tailings for grazing cattle after mine closure, in Proceedings Life-of-Mine 2014 , pp 563–572 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

The mining industry, both here and internationally, is continually developing increasingly sophisticated software to compute mineral resource estimates, but these processes cannot compensate for a flawed geological interpretation of the geology of the economic commodity(s) concentrations. Quality assurance and quality control (QA/QC) is becoming increasingly common in association with the sampling and assaying practices within the industry. However, it is rare in the case of a geological interpretation associated with mineral resource estimation. Why? In the context of this paper, QA/QC relates to the use of statistical and graphical tools to show that the geological economic commodity concentrations have been appropriately domained. Domaining is essential to improve the chance of getting a mineral resource estimate right. Commodity value and acceptable concentration variation within a mineral resource can be ingredients that make mineral resource estimation difficult to get right. But it is possible to get it right a very high proportion of the time. It is more likely to occur when inappropriate data consolidation is minimised. In any case, inappropriate data consolidation is significantly reduced when the geological interpretation is strongly consistent with the data and it is demonstrable. To achieve quality global estimates of geological domain concentrations, it is essential that the geology of the prospect is understood sufficiently that the deposit is appropriately domained. Appropriate domaining occurs when sample populations are separated in such a way that only data in harmony with each other within the population contributes to the domainÆs concentration estimate. The paper will use four brief case studies to illustrate how QA/QC can be used to display data and validate the underpinning geological interpretation through its associated domaining to get it right when it comes to a mineral resource estimation.

Jan 1, 2007

Copper-Cobalt hydrometallurgy has seen a resurgence in recent years with the development of projects in Zambia and the DRC. Many of the flow sheets are unique in their use of hydrometallurgical techniques to improve performance compared to the older types in current use. The emphasis has moved from direct copper electrowinning/stripping, with multiple stages of precipitation for removal of impurities and concentration of cobalt, to innovative use of solvent extraction and ion exchange with higher cobalt recoveries to final product. The poor quality direct electro-won copper has been supplanted with solvent extraction-electrowinning; with consequent production of LME 'A' quality metal. Many of the precipitation steps in cobalt recovery and concentration, have been replaced with solvent extraction; while the remaining precipitation stages have been enhanced with use of oxidants to improve impurity removal. Operating experience from two of these circuits has shown the benefits of the new technologies and the improved overall recovery of both copper and cobalt into higher quality products.

Jan 1, 2008

By ZáWang, F Hungerford, T Ren

Operations in an underground drill site have to co-exist within the mineÆs ventilation and operational system. The space requirements of a drilling operation have to be adapted to the limitations provided in available site space, which is usually defined by standard mining operations and geotechnical influences. These limitations affect borehole design, equipment positioning in the site layout and possible interactions with mining equipment and services such as water and power supply.The ventilation requirements for drill sites and the means employed vary with depth of the site, space and likely presence of gas. All drilling operations provide a particular service for the mine and in each case, drilling must operate in a manner which controls all gas, water and cuttings returning from the borehole. The various standpiping systems employed have evolved under differing influences and must cater for conditions during and after the drilling operations.The influences that gas content, pressure and flow, rib stability, cleat direction, borehole length, potential water pressure and flow have on a mineÆs operation and ventilation systems have to be considered in the design of standpipe length, diameter and fittings. Past history has a strong influence on common practice while worst case effects of a possible in-hole event should be catered for.This paper describes the early drilling systems and their limitations in ventilation and gas management. The drill site dimensions and set-up are discussed in the context of roadway conditions, equipment layout, ventilation and logistics. The use of standpiping to control all returns from the borehole is illustrated by referring to likely scenarios in a drilling site to achieve the most effective sealed depth to accommodate the worst case possibility of intersecting high pressure gas or water during the drilling operation. Practices to allow gas drainage in the return airway of a panel are described.CITATION:Hungerford, F, Ren, T and Wang, Z, 2013. operational management of underground in-seam drilling sites, in Proceedings The Australian Mine Ventilation Conference , pp 43-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By O Dominguez

Significant value can be added to ore supplied from the mine to the mill by measuring its quality in real time and performing grade control additional to that within the mine. Responsibility for ore quality between the mine and mill stockpiles is not always clear due to operational siloes so geologists and mining engineers need to be involved collaboratively with metallurgists to optimise ore value prior to processing. Sensors, such as the GEOSCAN-M which utilises high specification Prompt Gamma Neutron Activation Analysis (PGNAA), that measure conveyed ore flow representatively (continuous and fully penetrative) and in real time have been used in the minerals sector since 2003 and have been successfully applied in multiple commodities. Quality can be measured within the mine where material is conveyed underground or in-pit. Bulk ore sorting is used to divert increments of waste from the ore stream to upgrade material sent to the crushed ore stockpile (COS) as well as to create run-of-mine (ROM) stockpiles of different qualities to maximise blending opportunities and accommodate processing priorities, eg blending out deleterious content. The real time composition measurement can be combined with moisture and fragmentation analysis data for improved ore type characterisation, to control ore blending, for feedback to the mining schedule and block model reconciliation, and feed forward control for grinding and processing operations. The paper discusses various parameters measured and derived in existing operations that are used to maximise coarse waste rejection and metal recovery, optimise plant feed quality consistency, and reduce consumables; power, grinding media, water, reagents, and minimise fine tailings generation. Innovative geometallurgy applications are also discussed.

Mar 22, 2022

By S Nkwanyana, I Govender

Batch experiments in a 0.6 m diameter mill have shown that improvements of about 13 per cent in the efficiency of energy utilisation can be realised in ball mills by replacing 25 per cent of the ball charge by an equivalent volume of cost-free critical size pebbles from AG/SAG mills. For a mill of a given size, speed and charge filling, the rate of size reduction of ore particles depends on (i) the frequency of grinding media collisions (ii) the probability of capture of ore particles between the colliding grinding media (iii) the probability of fracture of the captured particles. The probability of fracture depends on the magnitude of collision energy. The distribution of collision energy into shear and impact events determines the relative strengths of attrition breakage and impact breakage. The efficiency of energy utilisation depends on which of the two mechanisms of breakage is more desirable in a particular milling stage. In this paper collision data from a series of DEM simulations of a mill charged with steel media and a mixture of steel media and pebbles is presented in energy spectra and spatial distribution maps. The data provides the necessary detail to elucidate the improvements in the efficiency of energy utilisation in ball mills when using a mixture of pebbles and steel media.

Aug 24, 2022

The paper examines the difficulties encountered by objectors to mining privilege applications. It describes the various involvements of the environmental defence society in the mining controversy and makes some comment on the proposed amendments to the Mining Act 1971.

Jan 1, 1981

By N Power, A D. Costar

There has been significant growth in mining and energy exploration in South Australia, which has identified new major potential opportunities. This sector generates significant economic value to the state and their support remains a priority for the state government. The delivery of this economic and associated community value to the state is dependent on the mining and energy sector being able to access reliable water supplies.The vast majority of priority areas for the mining and energy sectors are located in areas that have traditionally been of low priority from a water-use perspective and hence, data and knowledge levels are generally low.Recent studies have identified a potential increase in demand for water in the mining and energy sector for potential developments from approximately 40 GL to over 170 GL over the next ten years. The studies found that water and water infrastructure is the second highest proportion of planned infrastructure capital investment by resource companies. The South Australian GovernmentÆs Plan for Accelerating Exploration (PACE) initiative (PACE 2020), also identifies addressing the issues of location, use and management of South AustraliaÆs water resources as a key priority for the growth of the mining and energy sector.The Department of Environment, Water and Natural Resources (DEWNR) has developed the facilitating long-term outback water solution (FLOWS) initiative. DEWNR is currently undertaking a suite of programs to provide groundwater information at the regional scale to better target water supply options for mining and energy developments and community water supplies.The Goyder Institute for Water Research has leveraged significant research investment of $3 M to develop methodologies to interpret airborne geophysics to map groundwater sources.The FLOWS Initiative will provide key content for the PACE Water Program and will also assist in the development of water supplies for remote far north communities by identifying alternate groundwater sources to improve water supply security.This paper will discuss how developing an appropriate science and knowledge base will encourage and secure development where appropriate, enable prudent decision-making and policies regarding water allocation, accounting and licensing, whilst ensuring the protection of environmental assets.CITATION:Power, N and Costar, A D, 2013. Finding long-term outback water solutions, in Proceedings Water in Mining 2013 , pp 191-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By J A. M Luz, A T. Bernardes

HukkiÆs law is an empirical law, which does not take into account several events of energy loss during the fragmentation processes. Since experimental results are very difficult to obtain, for a large range of fragment sizes, the verification of the law is very difficult. The relation between fractures and fragmentation processes with fractal geometry was proposed some decades ago. Empirical laws known in this context show basic features of fractal geometry, mainly self-affinity and power law behaviour. Thus, in this work a model was developed to simulate the fragmentation process and to check the relation between energy consumption and fragment sizes. The model is represented on a regular lattice. Links can represent pathways for fracture processes. The events of fragmentation have energy given by a probability distribution function. In the model there is no mass loss. Propagation of fractures occurs as self-avoiding random walks on the regular lattice.

Sep 26, 2011

By I Jabou, D G. Blazak, L C. S Hogarth

The R70 test is a good indicator of coal reactivity to oxygen and is commonly used to provide a rating of propensity for self-heating. Tests performed by The University of Queensland Spontaneous Combustion Testing Laboratory have resulted in the development of a large database that shows the impact of coal quality on this parameter. From these results it is possible to infer an R70 value, which can be used to gain an appreciation of the intrinsic coal reactivity before it is even tested. However, any interpretation of R70 values must consider the influences of coal rank, mineral matter and moisture content to provide a better understanding of the spontaneous combustion risk of a particular coal.

Jan 1, 2005

By R A. Anand, N N. Viswanathan, M M. Pande

Slags are the most voluminous solid by-products generated in pyrometallurgical operations, and, as such, finding an application for these oxidic materials is pertinent to maintaining resource efficiency. In particular, pyrometallurgical copper production is associated with high slag rates, typically ranging from 2.2 to 3.0 tons of slag per ton produced copper, which necessitates slag valourisation. A possible application for these iron silicate slags is as supplementary cementitious materials (SCMs), which effectively lowers the CO2 emissions per ton of cementitious material. Although utilising iron silicate slags as SCMs has been studied in previous work, the scientific literature has limited data on the effect of composition on the inherent reactivity in cementitious systems. More specifically, no reports on the impact of FeO/SiO2 ratio have been presented in previous publications. Therefore, the present study aimed to isolate this parameter in a synthetic FeO-SiO2-Al2O3-CaO-MgO-Cr2O3 system. Since the amorphous content is a pertinent parameter for SCMs, a high-temperature confocal laser scanning microscope (HT-CLSM) was utilised to assess the crystallisation behaviour at continuous cooling conditions. Furthermore, high-temperature rheological experiments were conducted to measure the viscosities of the slags in relation to the crystallisation behaviour. The experiments showed that depolymerising the slag by increasing the FeO/SiO2 ratio generated a less viscous slag, which showed higher tendencies for crystallisation. Furthermore, experiments assessing the inherent reactivity as an SCM showed that depolymerising the slag by increasing the FeO/SiO2 ratio as the sole independent parameter generated an initially more reactive slag. However, replacing SiO2 with FeO was found to negatively affect the reactivity as measured over seven days within the tested compositional range.

Jun 19, 2024

By R Hao

Uncertainties in large open pit geotechnical modelling has been a major concern for slope stability analysis. The level of confidence in the in-put assumptions, such as structural and rock mass model, dictates the modelling results to some extent. This article is to detail a case study of Kalgoorlie Consolidated Gold Mines (KCGM) regarding a predicted inter-ramp failure on an as-built pit walls by a 3D numerical modelling. Significant concerns were raised across site and multiple preventive plans were considered. After intense data collection work, it was confirmed that the risk of failure had been overestimated. The case study has improved the understanding of geotechnical data in-put and has enhanced the process of creating and updating geotechnical structural models at KCGM.

Jun 22, 2022

By C R. Fountain, R J. Sinclair

The zinc industry is dominated by the electrolytic zinc (EZ) process. The EZ process has a low tolerance for impurities, resulting in tight concentrate specifications. Many mining companies sacrifice zinc recovery in order to meet smelter specifications. Some have ore-bodies that cannot be economically developed because too much metal has to be sacrificed, or it is just not possible to meet the specification. The BUKA Zinc Process (BZP) has been developed as a method of producing high-quality zinc from a wide range of concentrates. It can have lower capital and operating costs than the conventional zinc and lead production routes. Advantages accrue from increases in metal recovery during concentrating, smelting and refining; the elimination of most of the capital and operating costs associated with lead smelting; reduced transport costs; lower zinc refining costs; reduced refinery residue disposal costs; and reduced future environmental liabilities. This paper describes results of testwork that has been undertaken to demonstrate the viability of the BZP on both test rig and laboratory-bench scale.

Jan 1, 1998