Search Documents

By E J. Coyle, L A. Millington

Tailings storage facilities are geotechnically complicated structures that develop heterogeneous strength profiles and varied porewater conditions. The monitoring of porewater pressures is one of the only direct measurements that can be performed to monitor the performance of a facility throughout its life and is of particular importance in upstream facilities. Foundation underdrainage, continuous and staged tailings deposition, climate inputs (rain, snow, humidity, evaporation, etc), and stratified tailings permeabilities can complicate this critical measurement that introduces uncertainty to stability analyses. These difficult conditions manifest in vibrating wire piezometer measurements as very low or negative pressure readings, both of which are within the instrument’s range of accuracy. However, the data can be difficult to interpret, and a range of interpretations are adopted from optimistic low phreatic surfaces to conservative fully saturated tailings. Where tailings are potentially liquefiable, these very low readings introduce further uncertainty regarding the pore space saturation ratio and liquefaction potential above the estimated phreatic surface. This area of uncertainty is the vadose zone, and its affect on tailings behaviour is not well understood. The two facilities analysed in this paper are upstream, raised embankments with tailings classified as clayey, sandy silt that have been found to be potentially liquefiable. The vibrating wire piezometers (VWP) at both sites show very low or negative readings when they are initially installed near the surface and then go through cycles of re-saturation and de-saturation. Eventually the readings settle as the VWPs are buried deeper within the tailings. The instrumented sections within the tailings column do not show consistent readings that would be indicative of a hydrostatic phreatic surface at either site. Rather, they are highly variable and can be interpreted as either representing a high phreatic surface within the tailings or as a ‘perched’ phreatic zone within the tailings layers. How the VWP data is interpreted has a significant impact on how the facilities are raised and operated. The design outcome for Site 1, which adopts a lower phreatic surface, results in an embankment that meets factor of safety (FoS) requirements under residual strength conditions without any buttressing. Conversely, a conservative (high) phreatic surface has been adopted for Site 2 and has resulted in the facility requiring a significant buttress to meet FoS under residual strength conditions.

Jul 1, 2021

By D Lalor, N Goodman

The increasing demand for batteries is resulting in the development of large-scale projects for the production of key battery metals such as nickel and vanadium. Several of these projects plan to extract the battery metals from the ore via chemical roasting, leaving large volumes of waste iron oxides after fuming and/or leaching of the battery metals. These iron oxide wastes can be smelted in a HIsmelt furnace using biochar as the reductant, to produce clean, green pig iron with net zero carbon emissions. This green pig iron can then be added to basic oxygen or electric arc steelmaking furnaces to produce green, net zero carbon, steel. This paper describes the flow sheets and the economics for potential projects producing green pig iron via HIsmelt using waste iron oxides from nickel and vanadium production plants.

Sep 18, 2023

By P Card

Some project managers accept unsatisfactory economic evaluation modelling because they are unaware of what constitutes good practice. They tend to leave it to the evaluation specialist or others to decide. The AusIMM has published on its website a draft set of guidelines for technical economic evaluation which will allow these project managers to take control and demand worldÆs best practices.The style of the guidelines is described and the source of a worked spreadsheet example in Excel is given.Economic evaluation in project management is described. A simple test for the acceptance or rejection of evaluation work is offered. The nature of modelling and evaluation in each of the three study phases of concept, prefeasibility and final feasibility are described. Suggestions on the selection of specialists for each phase are given. The three levels of evaluation thinking are described, namely, modelling, valuation and evaluation. Finally the meaning of æfinancial analysisÆ is explained.The conclusion is that æthe role of an economic evaluation specialist is to create models and evaluations for the whole project team to readily understand and use: it is not to create models for his/her own useÆ.CITATION:Card, P, 2012. What project managers must demand from an economic evaluation!, in Proceedings Project Evaluation 2012 , pp 173-176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By G R. Power

A useful way to assess potential productivity of SLC mines is by quantifying tonnes/drawpoint/day to be extracted from the mine. However limited industry information has been published to help mines benchmark this number. This paper assesses industry data which can be used to support estimates of potential productivity from new mines based on tonnes/drawpoint/day. The information used has been extracted from historical production schedules which indicate what was achieved, rather than what was planned. It has been assessed using an algorithm created for the purpose and is presented with discussion of varying definitions of active drawpoints, analysis of the data and inquiry into some of the underlying contributing factors.

Mar 15, 2021

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By D Gerrard, J Begelhole, J Gerber

The Iron Magnet deposit has been mined since 2007 when Arrium (then OneSteel) commissioned the magnetite concentrator to supply feed to the pelletising plant in Whyalla. The concentrate quality requirement for the customer required consistent product with minimal variability. In the early stages of operation, it was identified that the feed variability introduced significant changes in the concentrate quality, which was outside the acceptable customer limits.In 2011, a geometallurgical regression model was developed that allowed for the estimation of concentrate quality produced from the feed material. This was based on a laboratory-scale Davis Tube Recovery (DTR) test performed on the feed material. The objective of the project was to characterise the raw ore in the pit to allow for blending prior to crushing. By blending the feed to the concentrator, minimal concentrate quality variation within the plant was achieved. The orebody was divided into geometallurgical classes, called ore types, based on the mineral texture and magnetic mass recovery. Each geometallurgical class consisted of material with similar metallurgical performances. For each individual blast pattern, the ore was grouped into the geometallurgical classes and a composite sample was created. The composite sample was put through the laboratory-scale DTR test and the results were used to estimate the metallurgical performance of the material.The characterisation process and feed pile build methodology was applied in early 2013 and went through an optimisation and streamlining phase. Since the implementation of the geometallurgical characterisation process, the plant has seen a significant reduction in concentrate variability and measurable throughput gains. The characterisation process has also increased the amount of material that is now classified as ore.CITATION:Gerber, J, Gerrard, D and Begelhole, J, 2015. Geometallurgy of the South Middleback Ranges magnetite deposit – predicting plant performance from the pit, in Proceedings Iron Ore 2015, pp 555–560 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The optimisation and validation of shearer cutting methods is a time consuming engineering task. Many different parameters, of which not all can be controlled, can vary. The easiest solution, to increase the installed power and the longwall length, is not always the best. A different cutting method can increase the capacity without the need of new machines. The Department for Mining and Metallurgy Machinery at RWTH Aachen University therefore developed ProSL, the simulation tool for shearer and longwall operations. ProSL enables the engineer to create his own cutting methods and compare it with other methods. Machine-data can easily be varied to see the impact on the method. The research shows that sophisticated longwall methods increase the productivity of the system. The paper presents the results of the calculation with ProSL and shows how higher efficiency and lower costs can be achieved.

Dec 6, 2010

By G Collecutt, D Proud, D Humphreys

"The hazards associated with dust explosions are well known, and coal dust explosions present a significant hazard in the underground coal mining industry worldwide. In earlier work, we presented computational fluid dynamics (CFD) simulations and test results for coal dust explosions within a 2.5 m diameter circular gallery, along with CFD simulations and test results for the suppression of these explosions with finely atomised water sprays. In this paper, we present refinements to the CFD modelling that yield a significantly improved calibration with the test results, and proceed to investigate by CFD the requirements for suppression of a coal dust explosion in a typical underground roadway. This work was carried out under an ACARP project and we gratefully acknowledge their assistance. CITATION: Proud, D, Collecutt, G and Humphreys, D, 2015. Computational fluid dynamics modelling of coal dust explosions and suppression systems, in Proceedings The Australian Mine Ventilation Conference, pp 309–314 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By M Haest, O Dominguez, D Mittrup

Technological innovations and emerging analytical capabilities are transforming the way drill samples are analysed, with real-time mineralogical analysis made possible. In addition, new business/technical requirements are challenging long standing processes to incorporate more sources of information during planning in order to improve compliance to plan during mining and processing. Unfortunately, the new sources of information that are added do not always have adequate protocols in place to ensure quality data is collected.Spectral data covering the visible – near – short wave – midwave – longwave range are routinely collected by the Geoscience and Exploration department at BHP Billiton Iron Ore for accurate mineralogical identification. These data are used for geological interpretations (logging and modelling) and prediction of physical variables (metallurgical and geotechnical properties).This paper introduces how sampling and quality assurance / quality control concepts have been applied in the spectral data process. The described routine for sampling, data collection/management and reconciliation has been developed to track system precision and accurately and consistently ensure the data is of high quality before it is used across the mining chain.CITATION:Mittrup, D, Dominguez, O and Haest, M, 2017. A new approach to implement quality assurance and quality control to technological innovations – quality of spectral data capture and processes in the minerals industry, in Proceedings Eighth World Conference on Sampling and Blending , pp 265–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By G Chitumbura

Raise boring is a critical aspect of mining at Xstrata Copper’s Mount Isa Copper Operations (MICO). MICO’s internal raise boring department regularly develops ventilation rises, orepasses and stope cut-off rises and reams approximately 2500 m per annum. Developed, trialled and implemented as standard practice over the past two years, procedural changes in constructing the raise bore machine’s foundations have significantly reduced operator exposure to raise boring’s inherent risks of working around open holes and manual handling. An additional cost benefit of this newly-adopted procedure is derived from reducing the likelihood of damaging the machine while de-rigging.When conforming to standard industry raise boring practices, exposure to an open hole begins when the reamer breaks through the concrete pad and ends when it is removed from the hole – a process which, depending on the size of the hole and the raise boring machine, can take up to three days to complete. Although wearing fall restraint equipment, operators working on and around the raise bore machine during de-rigging are continually exposed to the risk of falling from heights. In contrast, MICO’s newly-developed and successfully-implemented presink raise boring system reduces this exposure to a maximum of four hours, regardless of hole size. Exposure to manual handling hazards is also substantially reduced as the presink procedure eliminates manual placement of a 100 kg drill bit under the machine to commence pilot-hole drilling. Outcomes of implementing the presink System at MICO have been so beneficial that it is now standard procedure for all reaming in excess of 1 m diameters.

Mar 21, 2011

By S Fityus, K Koosmen, J Simmons

The purpose of this paper is to therefore investigate the hydrogeological characteristics of tailings, coarse and mixed rejects from coal processing to enable better understanding of the potential for undrained behaviours in coal mine spoil piles. This is achieved by analysing the results from permeability and oedometer testing of tailings, coarse rejects and mixtures thereof. Focus is given to the effect that tailings content has on the behaviour of mixed rejects, the transition point between drained and undrained material behaviours, and the evolution of properties with increasing stress that would occur with increased depth of burial in a mine spoil pile. The implications of the findings are discussed with respect to spoil pile stability.

Jul 1, 2021

By J H. Zietsman

The transition to more sustainable metal production is receiving much attention at present, and the iron and steel industry is at the centre of the conversation. New, more environmentally friendly production technologies, such as direct reduced iron (DRI) smelting furnaces, need to be developed in a short period of time. This necessitates increased use of computational modelling that incorporates more accurate material descriptions. The combination of large-scale multiphysics models of high-temperature processes with CALPHAD material descriptions leads to infeasible computation times. This can be resolved with the previously reported RapidThermo framework, which has been demonstrated to make equilibrium calculations orders of magnitude faster, within controllable limits of accuracy. In this paper, we explain how further material properties, which are important to modelling hightemperature reactors, can be added to the RapidThermo framework. This can improve the accuracy and usefulness of process and multiphysics models in the development of new technologies, which can significantly accelerate development cycles.

Aug 21, 2024

By L E. Howard

Micro-computed tomography (Micro-CT) is an X-ray imaging technique that produces high-resolution 3D computerised ‘virtual’ models of geological specimens based on the X-ray attenuation of different materials in the specimen. The ‘virtual’ specimens are made up of voxels, the 3D equivalent of pixels, each assigned a gray value based on X-ray absorption. Micro-CT has enormous potential for allowing non-destructive, digital analysis of structure and composition when the mineralogical phases can be digitally separated. However, variation in X-ray flux between scans results in highly variable grayscale values for identical materials. Consequently, materials usually have to be segmented manually, which is subjective, inaccurate, labour-intensive and time consuming. Here we present a protocol and imaging software package that can be used to accurately and precisely extract quantifiable information in a repeatable and objective fashion. The software will allow the separation, visualisation, measurement and analysis of spatial and volumetric distribution of different mineral phases without damaging the specimen. This paper explains the potential use of this protocol and software package to ultimately allow automatic segmentation and quantification of gold in drill core samples, removing subjectivity and inaccuracies from data processing.

Sep 5, 2011

No paper was submitted for the proceedings, verbal presentation only (no material available).

Jan 1, 1998

By Munive L

As a result of commissioning No.5 B F, 2670m3 inner volume, in March 1972, the largest B F in Australia; new expertise in maintenance, furnace operating practices and design have been obtained. This experience has also been extended to the other furnaces. A series of operating problems were con- fronted; all parts of the furnace, including the hearth side walls and bottom,were adversely affected. In December 1977, serious hearth wall wear was detected at No.5 B F, and a potential hearth breakout was averted. Hearth wear in No.4 B F was discovered in March 1979, and emer- gency underhearth cooling was installed to reverse an extremely advanced hearth bottom erosion. Hearth behaviour of No.5 B F oampaign 1972-1978 and`No.4 B F campaign commencing 1972, has been studied and discussions on the causes, effects and measures undertaken to protect the hearths are presented in this paper.

Jan 1, 1981

By S Grobler, T Fares

Understanding the real utilisation of the available volumetric capacity of a conveyor is key to unlocking latent capacity or ‘debottlenecking’ existing plant. Conveyors are typically designed on the basis of conservative density and ore surcharge angle specifications, and consequently there is often latent volumetric capacity available.Laser scanning measurements of conveyor ore profiles has been undertaken on iron ore conveyors to gain an understanding of the actual surcharge angle and the available edge clearances. Iron ore producers seeking to extract maximum production from their assets have used these measurements to debottleneck existing plant and to revise the design criteria for future plant. The benefit is that latent capacity of existing plant can be unlocked and smaller and cheaper conveyors can be designed for future plant, maximising the return on capital. This paper describes the measurements and results.CITATION:Fares, T and Grobler, S, 2015. Laser scanning of conveyor ore profiles, in Proceedings Iron Ore 2015, pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A R. Hollis, M Heddon

The safe life cycle of a Tailings Storage Facility (TSF) is founded on the fundamentals of proper design, construction, operation and closure. Leinster Nickel Operations (Leinster) utilises four active TSF cells that are cycled between filling (deposition), desiccation, and construction to meet a targeted rate of rise. This results in ongoing and consistent raising of the TSF walls. Critical to maintaining the safe life cycle through this consistent wall raising is precision construction and high frequency quality assurance to ensure compliance to design requirements and TSF walls free from defects. Leinster has recently deployed Intelligent Machine Control technology for TSF construction. Advances in Intelligent Machine Control have decreased variability in construction; ensuring variations are within the tolerances of design. The Intelligent Machine Controls are programed to ensure construction conforms to design tolerances of +/-30mm. This level of accuracy provides assurance of borrow area set out, compacted layers are as per design, compaction monitoring is within the zone placed, scarification between layers to prevent lamination is maintained, and batter angles are set to the correct grade. This level of control provides certainty that construction meets the design intent. In conjunction with Intelligent Machine Control, periodic drone surveys are conducted to verify construction against design. Advancement in survey equipment and techniques allow higher frequency, high accuracy survey to be completed on demand by site based personnel. This provides quality assurance through all stages of the construction phases, as well as the final constructed wall, ensuring compliance to design. Combining Intelligent Machine Control with higher frequency quality assurance provides an increased level of certainty that the TSF construction is defect free and within quality specifications. These recent technological advancements in Construction and Quality Assurance ensure cell raises are constructed to the design intent with greater levels of accuracy and precision than ever before.

Jul 1, 2021

By A D. Campbell, G R. Power

The increasing availability of marker data in sublevel caving operations is changing the way draw can be managed to achieve positive recovery outcomes in these mines. This paper describes how marker data has been incorporated into flow simulations to help calibrate full mine ore recovery simulations for the forecasting and optimisation of recovery.Some flow modelling techniques do not use marker data, relying instead on the outcomes of physical and numerical experiments to guide assumptions about an idealised recovery flow shape. Other mines have access to marker trial data, but find it difficult to specifically link this marker trial information to their recovery models. This can make it difficult to create a link between the marker trial information and recovery forecasting and limits the potential value of the marker trials at the mine.In the simulations shown here, the marker rings are fully incorporated into the flow model, and can be tracked in the model. The model is compared against the real underground marker recovery information to give the user an indication of how accurately the flow settings in the model are reflecting the conditions in the experimental marker rings. An example of use of this system at an operational mine is included.CITATION:Power, G R and Campbell, A D, 2016. Modelling of real-time marker data to improve operational recovery in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By P Chapman, B Moosapoor

The objective of this paper is to present the potential applications of geostatistical analyses in planning CPTu investigations, as well as interpolation of CPTu data. The paper presents a case study of a geostatistical analysis of CPTu data undertaken between 2004 and 2017 for an upstreamraised TSF located in the Goldfields region of Western Australia. An initial model is developed using the 2004, 2009 and 2017 CPTu data. The model is used to predict in situ cone tip resistance (qc) measurements, as the interested primary variable, at the selected locations where 2019 CPTu were undertaken, and the results of the prediction and the actual data are compared.

Jul 1, 2021

By P J. Handley

"Predicting how coal seams will be beneficiated through the coal handling processing plant (CHPP) has long been challenging within BHP Coal. Various coal seams from different areas are mined and stockpiled separately, often depending upon a deleterious coal quality parameter; high/low trace elements for example. These stockpiles are then fed in different ratios into the CHPP to produce the desired product/s. In understanding the washability characteristics of the feed source, mine geologists and process engineers work together to improve the beneficiation of different coal materials through the CHPP.For the majority of the BHP Coal deposits, the washability data is available for the coal seams across the deposits. However, no previous standardised modelling and prediction technique existed that could ensure the correct information was available for forecasting and refining CHPP processes. This paper will discuss the steps undertaken to implement a geometallurgical prediction tool that simplified and streamlined the washability modelling and yield estimation process. The value realised to the BHP Coal assets resulting from this process was: improved compliance to plan increased throughput increased CHPP recovery through improved efficiencies and increased revenues.CITATION:Handley, P J, 2017. Washability modelling and estimation techniques used to improve coal handling preparation plant beneficiation, in Proceedings Tenth International Mining Geology Conference 2017, pp 327–336 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017