Search Documents

By S H. Algie, D P. Taplin, S G. Doig

"Suboptimal performance of clusters of hydrocyclones (cyclones), relative to the performance of the individual cyclones that comprise the cluster, is a common phenomenon. The primary cause is well known: uneven distribution of the slurry feed into the individual cyclones. The direct result of uneven distribution is that each cyclone in a cluster performs somewhat differently. Hence, some, if not all, of them do not work at their intended operating points, and the classification is not as sharp as intended. The impact on grade, recovery and milling efficiency will vary depending on the duty of the processing circuit, but the most immediately apparent consequence of uneven distribution is a difference in wear rates in the individual cyclones; this exacerbates the problems of unequal performance of the individual cyclones. In severe cases, and as differential wear proceeds, flows from the individual cyclones may become visibly different. Uneven distribution, once the phenomenon was identified, was seen to be a significant issue in the high-solids hydrocyclone cluster in the ball mill recycle section of Evolution Mining’s Edna May Operation (EMO, Westonia, Western Australia) gold processing plant. In 2012, a FloCEP® hydrocyclone feed distributor system was installed to alleviate the problem. Over the next four years of operation, this innovation has proven its value in the metallurgical and maintenance areas. Individual cyclones now wear at the same rate, greatly reducing the need for operator intervention, as well as increasing overall plant availability through minimising unplanned maintenance. The costs of the installation can be justified by savings in maintenance alone, though the greatest value, as is described in this paper, is in allowing the plant to produce consistently closer to its operational design limits. The FloCEP® system is a low maintenance, readily installed retrofit, based on two patented devices that are combined with complementary proprietary design methodology allowing customisation for specific flow rates and slurry particle properties. Together, these devices produce and distribute a pseudo-homogenous slurry flow without moving parts.Citation:Taplin, D P, Doig, S G and Algie, S H, 2016. Experience with FloCEP® Slurry Flow Conditioning at Evolution Mining's Edna May Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 251–260 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M Hawkins

The Clem Jones Tunnel (formally known as the North-South Bypass Tunnel), a A$2.88 billion road tunnel project in Brisbane, Queensland, was successfully completed almost seven months ahead of schedule. The project included two parallel 4.7 km long road tunnels, 740 m of intermediate roadway access ramps and two auxiliary ventilation tunnels. The tunnels incorporate intelligent tunnel systems, best practice fire and life safety standards and typical civil tunnel elements.Over the duration of the project the Parsons Brinckerhoff (PB) and AECOM (formally Maunsell) design joint venture (MPB) were Lead Designers to the Leighton Contractors and Baulderstone Bilfinger Berger Joint Venture (LBBJV). Construction of the toll road commenced in September 2006 and was completed in March 2010, with the tunnel opening then. Contributing to the success of this project was the continued support the lead designers gave throughout the construction period.This paper will focus on some of the structural elements that contributed to the success of the project – in particular the cable tunnel structure, a small precast, culvert shaped element under the pavement of the mainline tunnel, and the fit-out of the Gibbon Street shaft which were designed to be constructed in a combination of precast and in situ concrete.The cable tunnel was incorporated early in the design phase and runs the length of much of the tunnel. This paper will outline the challenges faced by the designers with implementing this system which provided significant construction advantages, among which were being able to install a separate ventilation duct during construction and to start fitting out the mechanical and electrical conduits and drainage system while tunnelling was still underway.The Gibbon Street shaft had a length and width of 20 m by 40 m and an overall depth of 38 m. A 20 m high structure of precast and in situ concrete was constructed in the base to accommodate mechanical and electrical equipment and provide a take-off access for the southern ventilation tunnel. The construction purpose for this structure was to provide a junction between the tunnel boring machine (TBM) and the roadheader-style tunnels, a staging platform for commencing the roadheader tunnelling, and a platform where the TBMs could be dismantled and removed.The design was assessed and reviewed many times throughout the construction process to address the needs of each of these stages. Innovative use of precast concrete was used to minimise construction time.Additionally, the designers provided support to the construction team from the time of design completion through to the tunnel opening. This meant that the changes to the design and adjustment of construction loadings could also be assessed. The fi nal outcome resulted in an efficient construction sequence and a project that has provided an excellent outcome for the client, stakeholders and community.

Mar 8, 2011

By P Holtham, J Meng, E Tabosa, W Xie

Turbulence and its distribution are of great importance in flotation, and have received considerable attention recently. However, there is no mature technique to measure turbulence in three-phase (liquid-solid-gas) industrial flotation cells due to the opaque, highly aggressive and abrasive nature of the slurry involved. Previous research has shown that the piezoelectric vibration sensor (PVS) is a promising tool for turbulence measurement in industrial flotation cells. The PVS is a robust device that converts mechanical vibration to electrical signal, from which turbulence information can be extracted. An improved calibration method has allowed development of a frequency model to calculate the force applied to the sensor. Experimental results and comparison with laser doppler anemometry (LDA) have shown that the PVS can measure fluid kinetic energy, which is related to turbulent kinetic energy, a parameter used in the literature to represent turbulence in flotation. Laboratory measurement in a two-phase (water and air) 60 L cell and with slurry in a 3.5 L cell gave good stable results and mostly consistent trends between the measured turbulence profile and cell operation. When applied in a 300 m3 industrial cell filled with water, the addition of air or slurry to the cell resulted in a shift in the turbulence profile. This is expected because a change in fluid density will change the force applied to the sensor. It is therefore concluded that the piezoelectric sensor is an easy-to-use and robust technique that is fully capable of measuring turbulence in industrial flotation environments.CITATION:Meng, J, Tabosa, E, Xie, W, Runge, K C and Holtham, P, 2014. Development and application of a piezoelectric sensor for turbulence measurement in industrial flotation cells, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 457–470 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M English, M Yumlu

At times of high metal prices, mining projects that have previously been put into the ætoo hard basketÆ are now being more closely examined. Typically these projects include the potential recovery of small mineable tonnes with high contained metal values and often with poor ground conditions. For many underground mining projects, the drift and fill method is viewed as a high-cost method and a æmethod of last resortÆ. As a result the method is not well known in Australia and it is the authorsÆ view that the method is under utilised. The drift and fill method can be applied to a variety of underground mining situations and is a preferred method for some orebody geometries and where ore recovery is viewed as a key to project success. This paper examines some of the critical mine planning and backfill issues involved with the drift and fill mining method.

Jan 1, 2008

By C Donnelly

Redpath Australia is using a unique mining method for the Australian underground coal industry at Kestrel Mine Extension in the Bowen Basin, Central Queensland.The project involves completing two separate drifts from the surface for access to the German Creek Coal Seam located approximately 230 m below the existing surface. The scope of work is primarily the construction of two drifts; the first is 1577 m at 1 in 6 gradient and the second 1874 m at 1 in 8 gradient. Each drift has been developed by a Mitsui S200 roadheader with modifications to allow for a continuous tunnelling/mining cycle operation. A shotcrete boom has been fitted to the left hand side of the machine with the operators console located at ground level. Another operators console is elevated on the right hand side of the machine to allow operation of the rotary drill boom which is mounted on a slide rail to allow flexibility of positioning depending on the stage of the cycle. In support of the roadheader activities, an integrated conveyor system mounted on a sliding floor arrangement is able to be advanced as the mining face progresses. This sliding floor consists of four 1.5 m × 6 m sections that utilise hydraulic rams to ‘walk’ inbye, allowing room for installation of precast concrete floor panels for final floor completion. This method borrows from the tunnelling and construction industries to eliminate place-change delays in the mining cycle by enabling complete ground support installation without retreat of the primary development machine from the face. The aim is to reduce the project duration with the completion of final floor and services to within 30 m of the operating face as it advances.

Mar 21, 2011

Today, more and more tunnel ventilation systems are based on NO2 (or NO) and visibility measurements. Due to the significant decrease of CO emissions in countries with EU emission standards, which were adopted by Australia in 2004, CO is no longer a key factor for tunnel air quality monitoring and is often only measured for plausibility reasons (eg according to the German guideline RABT2006). Nitrogen dioxide, which is a good indicator for the overall air pollution along roads, is now taking over the leading role not only for ventilation control but also for air quality monitoring and in future probably for checking the function of air filtration plants in tunnels. Due to the lack of equipment for reliable and long-term NO2 measurements in road tunnels in the past, there are only very few standards giving limit values for NO2 in road tunnels. Furthermore there are not many records of NO2 readings over longer periods in different types of tunnels. SICK MAIHAK, a major supplier of measurement devices for controlling tunnel ventilation, has introduced the first monitor in 2006, specifically designed for measuring NO2, NO and visibility simultaneously in road tunnels. There are now experiences and results from the first tunnels equipped with this kind of system. This paper will present and discuss the results and experiences from these tunnels and explain the different levels of NO2 in different tunnel types. Furthermore, the status of air quality standards for road tunnels regarding NO2 limit values and the current status of discussion in various countries about NO2 limits will be presented.

Jan 1, 2008

By T D. Jolly, L A. Balzan, A R. Harris, Z Bauk

"The availability of real-time data in any process control system is critical for effective management of that system. At MMG LXML Sepon Copper Operation in Lao PDR, controlling the copper grade of the feed to the leaching circuit is paramount for maximising both productivity and copper recovery. Since 2008, real-time analysis data has been available to the process engineers from the Geoscan on-belt analyser installed on the Copper Mill feed conveyor, and highly accurate results on copper grade have allowed the process engineers to strictly control blending to overcome the variability in plant feed grade. The availability of real-time analysis data is crucial, as effective sampling of this stream is both difficult and error-prone, being only a snapshot in time of highly variable ore stockpiles, as well as having significant laboratory turnaround delays. Periodic sampling is used to verify the Geoscan data as accurate. Since its installation, the copper result has been the most critical output of the Geoscan. In recent times, the process engineers have sought to utilise other results from the Geoscan to further improve and control the process. One measurement of particular interest involves the real-time measurement of calcium and magnesium as a gauge of ore feed gangue acid consumption. To satisfy this end, accurate measurement of calcium and magnesium is becoming increasingly more important and has been the subject of ongoing collaboration between Sepon and Scantech, the manufacturer of the Geoscan. This paper discusses this work, describing the calibration process and results obtained, while also providing a basis for Geoscan use in operations to enable enhanced process control for all potential Geoscan users.Citation:Balzan, L A, Jolly, T D, Harris, A R and Bauk, Z, 2016. Greater Use of Geoscan On-belt Analysis for Process Control at Sepon Copper Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 231–238 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By T Sprague, D Pateman

"The Gosowong Gold Project is owned and operated by PT Nusa Halmahera Minerals (PT NHM), an Indonesian company 75 per cent owned by Newcrest. It is located on Halmahera Island, in the North Maluku Province of the Republic of Indonesia, approximately 2450 km north-east of the national capital, Jakarta (Newcrest, 2017).Kencana is one of two underground gold and silver mines at the Gosowong Operation where ground conditions vary from competent to very poor. Development headings occurring in poor rock mass conditions require high capacity ground support including long tendon cable bolts. Manual installation of cable bolts in these development headings has been a time consuming process due to borehole collapse, blockages requiring subsequent re-drilling and a minimum eight hour grout curing time interval. The installation of cable bolts including the setting, plating and tensioning can impact the critical path for development heading advance resulting in development cycle delays.A review was conducted by PT NHM on current industry practices for alternatives to manual cable bolting. PT NHM subsequently approached Minova to assist with the development and trialling of self drilling anchors (SDAs) installed using jumbos with a rapid setting pumpable resin, CARBOTHIXTM. A series of system development trials were conducted and a reliable bolting system was developed utilising the existing jumbo drilling fleet with minimal required modifications.The system developed was a ‘one pass’ bolting process to install and grout SDAs using a two component resin with a remote, mechanised system. Improvements achieved from the system include: eliminating hole closure issues and more immediate support in poor rock mass effectively reducing personnel exposure to poor ground conditions by removing the requirement to access the drive backs reducing grout set time with full installation times for 6 m SDAs averaging 25 min.The resin grouting system has now been successfully implemented to effectively manage areas of poor ground conditions and to accelerate advance rates in high priority headings.CITATION:Pateman, D and Sprague, T, 2017. Development and implementation of a long tendon bolting system utilising resin grouting technology, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By P Viljoen, A Holland, C Parken

In the raisebore industry, there are two known methods of removing large diameter reamer heads once the reaming of an underground shaft is complete: 1. Lower the reamer head to the base of the shaft and use a thermal lance to cut the drill string and drag the reamer away from the hole. This method exposes the person doing the job to falling rocks from the unsupported mineshaft, a hazard which is difficult to control and has caused fatalities. 2. Install breast plates in the backs above the reamer head at the top of the hole, and use air hoists to lift the reamer out of the hole. Steel beams are then placed across the hole which the reamer is lowered down onto, dragged forward away from the hole, disassembled, and removed. This method is time consuming, expensive, and complex in the controls required to ensure safe completion of the job At Carrapateena, the air hoist method had been successfully used, however, with the cost involved and the complexity of this process, development of an improved and fit for purpose reamer removal method was pursued. OZ Minerals collaborated with Pybar to develop an industry first application of Enerpac SL100 lift and shift technology; a track mounted system with hydraulic lifting units that can both lift the reamer out of the hole and tram it back along the tracks away from the hole. A key component of turning the idea into a reality was by establishing a truly collaborative relationship between client and contractor. When the SL100 mobile gantry arrived, it was set up in Adelaide and trialled with the whole raise bore crew attending the two-day workshop and risk assessment; a rare opportunity for drillers. There have now been five successful reamer removals with the SL100 mobile gantry at Carrapateena. It has proven to be an efficient process with the entire process from setup to demobilisation taking less than 48 hours. This new way has completely removed hot works and uncontrolled hazards from working at the bottom of a shaft. It has also saved the reamer stabiliser from being cut and thus wasted. Exposure to the open hole has been minimised significantly as assembly of the SL100 is completed well forward of the open hole. This new process is exponentially safer, quicker and cheaper.

Mar 15, 2021

By G Balog, T Ormerod, D Cox

This paper discusses the methods utilised by the technical team to identify and quantify the SLC risk factors, the modifications to mine design and scheduling, and the changes to the planned risk management practices. The paper also describes the future work currently planned by the OZ Minerals technical team to quantify the various risk factors in terms of space, time and magnitude. This may better inform the future mining practices within not only the Carrapateena province but also the wider Gawler Craton.

Mar 15, 2021

By Watters R

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By Baker G

Chromite was recorded among the rare minerals in the natural beach sand concentrates on the coast of Northern New South Wales by Whitworth(l) in 1931, and the commercial production of zircon and rutile from these beach sands has yielded concentrates of ilmenite with small amounts of chromium. The chromite is a detrimental impurity in the utilisation of the ilmenite, and the difficulties that attend the separation of the small amount of chromite from the ilmunite have raised suggestions from time to time that chromite occurs with ilmenite in composite grains. The absence of such composite grains and the nature of the chromite grains has been indicated by the following mineragraphic examination of magnetic concentrates containing chromite which were prepared by the C.S.I.R. Ore Dressing Laboratory, Melbourne University, from ilmenite concentrates from beach sands at Norrie's Head, County Rous, New South Wales and Stradbroke Island, Queensland.The magnetic concentrates from each locality are divided into five fractions, and the No. 1 concentrate is the most highly magnetic and the tailing the least magnetic. Chromium assays as determined by the Ore Dressing Laboratory are as follows:-

Jan 1, 1948

By S K. Panda, M A. Van Ende, S Chatterjee

Tata Steel Netherlands (TSN) aims to reduce its CO2 emissions by 35–40 per cent by 2030 and become CO2 neutral by 2045. A first step to reach these targets is via the utilisation of an Electric Arc Furnace (EAF), which will run on a mixture of high proportion of Direct Reduced Iron (DRI) and scrap. For an EAF operation, optimisation of slag chemistry is important to achieve the right mix of basicity (for refining especially dephosphorisation), foaming, volume (rate) and refractory life. Slag composition and rate can vary widely depending on the process variables like charge mix, charge composition, feeding rate, oxygen lancing, external carbon injection/addition, fluxing and refractory erosion/corrosion. Moreover, it is important to note that the slag composition and rate are ‘transient’ parameters and change throughout the heat. This makes all the dependent phenomena and/or outcomes transient as well. To describe all these effects simultaneously and be able to realistically simulate the EAF operations, a validated dynamic process model is important in the absence of real plant data. In this study, a validated dynamic EAF process model based on the concept of Effective Equilibrium Reaction Zone (EERZ) has been utilised to analyse the impact of high DRI industrial scale EAF operations on the transient slag characteristics – including slag volume (rate), composition, phases, solid fraction and viscosity. Simultaneously, the model is able to predict the impact on steel and offgas characteristics. Case studies were performed with 70 per cent DRI:30 per cent scrap mix considering both low and high-grade DRI. Both melting and refining aspects of the process including continuous feeding, arcing program, carbon addition, fluxing and oxy-lancing were considered.

Jun 19, 2024

During 2009 the technical services staff at Barrick Gold Corporation's Australian Business Unit conducted a review of their five underground mines that utilise pastefill as the backfill component for these operations. Of the five mines reviewed three use dry tailings and two use wet tailings plants. The primary aim for these reviews was to determine whether pastefill was the right option to be used, and if not, what where the alternatives. The reviews undertaken focus on several areas including, paste plant operation, reticulation and barricade techniques, the geotechnical requirements for pastefill in regards to the current mining methods, the consideration of alternative methods, capital and operating cost histories compared to initial estimates, and a cost benefit analysis of pastefill against other mining methods. The main benefits from the use of pastefill is increasing the extraction of the resource, reducing or eliminating the need to leave pillars. In some mines the use of pastefill is geotechnically driven, to manage high stress environments or mining induced seismicity. A third benefit of using pastefill in some circumstances is that it reduces dilution, however it is considered that this is not a valid argument for most of the mines reviewed. At two mines no alternative to pastefill was determined, whilst differing extraction and filling strategies were potentially identified at the other three mines. The reviews developed cost benefit curves for those sites that had alternative mining methods to assist in determining whether pastefill is the right option to use for any particular stope. At the grades typically mined in each operation, pastefill was the preferred option to use. In all mines, pastefill was determined to be the best option at this time.

Nov 25, 2010

By K W. Bian, Y M. Liu

Tongkuangyu Copper Mine is currently the only mine in China employing block caving. It comprises two large orebodies known as the No 4 orebody and the No 5 orebody. They are approximately 50° in dip angle, 80 to 240 m in width and 800–1000 m in strike length. The two orebodies are separated by a distance of 110–130 m. Production with block caving originally, ie Phase 1 project started at Tongkuangyu from the first undercut at a depth of 200–300 m below the ground surface and designated as Lift 810 m in late 1989 and has continued to the present. During the last 25 years Tongkuangyu has mined three lifts: Lifts 810 m, 690 m and 530 m. The previous two lifts utilised a slusher process with an annual designed production rate of 4 Mt. In this context the lift name represents the elevation of track haul level.The Tongkuangyu Phase 2 project serves for two lifts (ie Lift 530 m and 410 m) under the elevation of 690 m and the annual designed production rate is 6 Mt. Since the orebody is approximately 50° in dip angle, it is originally designed that production at Lift 530 m is comprised of one main extraction level and two auxiliary extraction levels in the footwall and undercutting is started from one end of the extraction footprint forward to another end, which is from north-east to south-west.Production at Lift 530 m started from March 2011 and reached to 6.39 Mt in 2013 and 6.9 Mt in 2014. Additionally, Tongkuangyu improved block caving processes and used modern mining equipment, which differ from the previous two lifts. Blastholes for undercutting and drawbell-preparation are now drilled using jumbos. The blasted ore is transferred to the underground crushing station via 10 t electric load-haul-dumps (LHDs) and then delivered to surface via a belt conveyor 3200 m long.Due to increasing ground pressure, a consequence of mining depth increase, stress abutment and inadequate support, significant damage occurred at the Tongkuangyu Copper Mine with production at Lift 530 m. This resulted in significant production delays and rehabilitation costs. A series of improvements have since been implemented including an advanced undercut sequence and increased ground support. All of these improvements have allowed Tongkuangyu to alleviate ground control issues, reduce operating costs and ensure safe production.CITATION:Liu, Y M and Bian, K W, 2016. Production at Lift 530 m of Tongkuangyu Copper Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Andrews B. S

The sinter plant at the Sulphide Corporation's Cockle Creek works produces a feed for the company's Imperial Smelting Furnace. The feed contains lead and zinc oxides and all the fluxes necessary for furnace operation. The quality of this feed is a major factor in furnace performance and the considerable flexibility of operation possible at the sinter plant has been used in efforts to achieve optimum operating conditions.Operating data is processed daily and information gathered from this source has led to three of the four improvements described.These improvements have resulted from elimination of gas recirculation, reduction of sinter returns sizing and alteration of ignition conditions and main layer fuel loading.

Jan 1, 1964

By S Munn

Today, it can be said that the majority of mines utilise communications equipment in one form or another. Either for communications between staff making their day-to-day operations more efficient, or for emergency communications, as well as linking computer based mine management systems, and providing remote control over complex mobile and fixed machinery. With the advances in technology now available, we are moving into the next generation of mine communications equipment, using digital communications in the underground mine environment. It is a proven fact that an efficient underground mine communications system can help maximise production, by providing major gains in areas such as equipment and manpower utilisation, staff and vehicle tracking, reaction times to break downs and emergencies. In this paper we will describe some of the facilities that are currently available, as well as what will soon be available to mining and tunnelling companies around the world.

Jan 1, 1999

By B Murphy, S O’Connell, J L. Heath

In the 1989 best-seller The 7 Habits of Highly Effective People, the author, Stephen Covey, highlights the importance of maintaining not only ‘production’, but also, ‘production capacity’. When operating a modern flotation concentrator, production is often measured in terms of concentrate tonnage, tonnes milled and plant utilisation. There are very few metrics that focus directly on flotation equipment condition in relation to performance, which is analogous to Covey’s production capacity principal. It is evident on many mine sites that flotation equipment condition is not monitored on a proactive basis and that the prevailing culture is to wait for a failure, before addressing an issue.This paper discusses examples of how poor equipment condition can lead to production loss through poor metallurgical performance. Actual examples are given where these problems have occurred in operating plants. An outline is provided on how metallurgical and maintenance departments can work together to protect production capacity and gain more from existing equipment.CITATION:Murphy, B, O’Connell, S and Heath, J L, 2014. Maximising value through maintaining your flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 71–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By S Doudle

The Iluka Resources Ltd Jacinth-Ambrosia heavy mineral sand mine (South Australia) is located in an undisturbed semi-arid landscape consisting of sparse trees, shrubs and grasses. The soil interspaces are covered with biocrusts, a living soil cover also found worldwide in arid regions. Biocrusts are composed of lichens, cyanobacteria, algae, mosses, liverworts, fungi and bacteria, and live on and within the first few millimetres of the soil surface. Biocrust organisms bind soil particles, sequester carbon and many fix atmospheric nitrogen making them important structural and functional components of ecosystems. Despite their important role in ecological processes, biocrusts are susceptible to disturbance; nevertheless they can recover provided sufficient inoculum is present. Cyanobacteria are the early colonisers and they capture atmospheric and landscape resources and establish conditions that subsequent successional seres can capitalise on. Research conducted in countries including China, Spain and South Africa has been focused on methods to either encourage rapid regeneration of cyanobacterial remnants or to introduce new material from cultured cyanobacteria. We have been investigating the extent and diversity of biocrusts across the 4500 ha mine lease and their potential to improve mining rehabilitation outcomes. Approximately 46 per cent of the soil surfaces are colonised with biocrusts and 33 taxa have been identified. Laboratory experiments were designed to mimic massive soil disturbance and treated with a range of water qualities. Within 22 days, treatments irrigated with fresh water were colonised by new cyanobacterial filaments with a mean surface coverage of 65 per cent. Secondary tests revealed that differences in the photosynthetic yield of the crust were dependent on the salinity levels of the irrigation water used. In 2011 this program is expanding from the laboratory into field scale trials designed to assess both the potential and practicalities of up scaling these techniques to provide crushed biocrusts and cyanobacterial bio-inoculum for use in mine rehabilitation.

Oct 5, 2011

By B Stewart

The SRS-1200 concept came about following the recommendations from the Board of Inquiry into the 1994 Moura No 2 mine disaster with the aim of having a system to remove personnel from an unsafe environment underground via a shaft where no other means of escape is possible. It is a mobile rescue unit that utilises a winding system to operate a man cage. It can descend the cage up to 1200 m into a vertical shaft. This operation is managed from the winder control compartment located on the non-driver side at the rear of the vehicle.

May 5, 2022