Search Documents

Fine Gravity Separation in the Reflux Classifier, Exploiting a High Shear Rate, Laminar Flow Mechanism The Reflux Classifier is used in the gravity separation of particles over a broad range of particle sizes. The device consists of a fluidised bed zone, with a system of parallel inclined channels above. The inclined channels provide a significant hydraulic advantage over conventional fluidised beds via the so-called Boycott Effect (Boycott, 1920). This paper describes a new advance in fine gravity separation based on the high shear rate and laminar flow profile that arises when closely spaced inclined channels are deployed. As reported recently (Galvin et al, 2009a), a powerful density based separation mechanism develops from this arrangement, suppressing the effects of particle size. In this paper we focus on two areas, firstly the application of the separator in the laboratory for batch fractionation of particles of varying size and density to determine the grade recovery curve and hence the liberation, and secondly the step change in separation performance achieved on a continuous steady state basis when closely spaced inclined channels are used. The variation in the separation density with particle size decreases significantly, and the Ecarte Probable Error (Ep) remains at low levels over a broad size range.

Sep 13, 2010

By G Hayes

Ore from the Browns deposit near Batchelor, in the Northern Territory of Australia, is a fine-grained polymetallic sulfide ore hosted in graphitic black shale. Minerals of economic significance are seigenite (Co,Ni)4S3, Galena (PbS) and Chalcopyrite (CuFeS2) with minor Sphalerite (ZnS). Gangue minerals include quartz, carbon and K-feldspar. The grain size is fine, with a significant amount of the seigenite present as Early flotation work determined that a grind size of around 20 microns was required to achieve clean sulfide concentrates. This work recommended oil agglomeration flotation, in which small sulfide minerals were collected, then loosely agglomerated with oil ahead of flotation into a heavily mineralised froth. In the 400 kg/hr prototype plant this froth proved unmanageable. A conventional flotation circuit after grinding to a P80 of 24 microns and using very low flotation pulp densities resulted in an 86 per cent cobalt recovery.The paper analyses further laboratory work which has increased cobalt recovery to 91 per cent by grinding to û250 microns ahead of flash flotation. The real cobalt recovery breakthrough comes from flash flotation of the whole mill discharge rather than the more usual flash flotation of cyclone underflow. Flash flotation tailings are ground to û38 microns and are floated under normal flotation conditions with only the scavenger concentrates being reground to 20 microns.A one tonne per hour prototyping campaign is scheduled to demonstrate the robustness of this circuit.

Jan 1, 2002

By R J. Worland, D Bowyer, J L. Mauk

The TerraSpec is a compact field portable mineral analyser that uses non-destructive reflectance spectroscopy for mineral identification. The instrument uses and measures infrared and visible light that is absorbed by certain covalent and molecular bonds (AlOH, FeOH, MgOH, CO32-, OH, H2O and NH4) within the lattice of a mineral at specific wavelengths producing an absorption spectral profile. A variety of minerals can be detected including clays, micas, carbonates, and hydroxides as well as some sulfates and silicates. However, not all minerals are detectable, such as quartz and feldspar. Alteration minerals replacing volcanic rocks have been studied for several epithermal prospects in the lower Waitekauri Valley (Sovereign, Jubilee, Scotia and Jasper Creek) and a geothermal field in the Taupo Volcanic Zone. At the Sovereign, Jubilee, Scotia and Jasper Creek prospects previous XRD investigations determined well developed clay mineral zonation with illite in the west (Sovereign and Jubilee) grading into interstratified illite-smectite (Scotia) and smectite (Jasper Creek) to the east. Although the percent of illite within interstratified illite-smectite could not be determined and some illite-rich illite-smectite (>90 per cent illite) and some smectite-rich illite-smectite (>90 per cent smectite) could be misidentified as illite or smectite respectively, the TerraSpec survey determined the same zonation of illite to illite-smectite and smectite. Common chlorite, rare calcite and local kaolinite were also detected. At the geothermal field, the TerraSpec was primarily used to determine the occurrence of kaolinite, dickite and alunite, which form in acid conditions. Widely spaced (every 50 to 100 m) XRD results are in excellent agreement with closely spaced (every 5 to 10 m) TerraSpec results that further determined the occurrence of these minerals in previously unrecognised intervals. It also determined the occurrence of zoned smectite, illite-smectite, illite, and chlorite alteration. Overall, the TerraSpec is a rapid mineral identification technique that is very useful in delineating the occurrence and distribution of certain minerals in both epithermal deposits and geothermal fields. Although the TerraSpec cannot detect as many minerals as XRD, the TerraSpec allows data collection at a sampling scale and speed (real time) that is not practical by XRD.

Jan 1, 2006

By D McClelland, R Whittering

Minerals and Metals Group (MMG) subsidiary Lane Xang Minerals Ltd operates a single site copper and gold mine near Sepon in Lao PDR. Gold production commenced in 2002 and first cathode copper production was in March 2006. Plant throughputs for gold and copper are currently 2.5 Mt/yr and 1.4 Mt/yr respectively; use of a second tailings dam has commenced accordingly. Although the increased catchment area creates opportunities for more storage to reduce demand on other water sources, especially during the dry season, it also creates greater requirements for water treatment capacity.The water balance for mining operations in a tropical monsoon environment with dry winters presents on going management challenges. A successful mining operation depends on a careful balance of water inputs and outputs. The challenge prior to every wet season is having enough storage capacity to absorb potential rainfall. Plant operation in the dry season benefits from water captured and stored from the wet season which reduces the dependence on river water. Release of excess water to the environment is necessary to cope with the overall positive water balance and depends on suitable and effective treatment of water in accordance with the environmental guidelines.Ausenco has recently built and commissioned a second water treatment plant at the Sepon Copper Plant to process tailings decant water.  The objective of the second Sepon water treatment facility is to increase the site water discharge capacity to maintain the water balance and reduce the dependence on river water.  Decant water treatment is required to precipitate the contained heavy metals prior to discharging to surrounding wetlands.  The main metal that needs to be removed from the site water to meet discharge water quality requirements is manganese, as heavy metals are already precipitated to required levels in neutralisation before the tailings are sent to the storage facilities. A site layout provision for removal of manganese to produce a saleable carbonate precipitate is incorporated in the polishing plant design (future installation).

Jan 1, 2009

By J Temos

This paper outlines a number of immediate practical approaches to continuous improvement in environmental management in the minerals industry. It puts these into context with longer time-frame step-change approaches whose gestation may take a decade. Examples of improvements and approaches are drawn from WMC operations.

Jan 1, 2002

In coal mining, geophysical techniques have an established application in determining the location of seam boundaries ahead of the face so that underground mines can be planned to avoid any geological structures that might disrupt production. Geophysics can also be used in geotechnical studies to determine the in situ properties of the rock mass and the response of the rock mass to the mining. The use of geophysical logs and microseismic monitoring in these geotechnical applications are discussed in this paper.

Jan 1, 2002

The segment of the Upper Cenozoic volcanic chain (CVZ) located on the western border of South America (16-28¦S lat.) is constituted by an association of strato- volcanoes and ignimbrite sheets, with high K calco-alkaline affinities. Strata-bound volcanoes, mainly of andesitic and dacitic composition, present along the whole chain, and various hydrothermal alteration zones, on the slopes and in the cores of eroded volcanic structures. Some of these altera- tion zones bear epithermal precious metal ores and sulphur deposits, which at present are being exploited. The studied Salar de Gorbea area, located in the Andes of northern Chile (25-26¦S lat.) contains a numer- ous group of Miocene to Quaternary stratovolcanoes, with advanced argillic and extreme silicification hydrothermal alteration in their cores and on their slopes, favoring the formation of great volumes of alunite within altered zones and sulphur deposits in the higher parts of the volcanic edifices. Simultaneously, siliceous hydrothermal breccia of the phreato-magmatic type, with evidences of hydromag- matic explosions are recognizable, allowing, in some cases, the ascent towards the surface of rock fragments belonging to the Paleozoic pre volcanic basement. Radiometric ages obtained in some of the hydro- thermal alteration zones (K-Ar in alunite) are slighty young- er than the unaltered rocks which constitute the strato- volcano. Trace element (Hg, As, Sb, S, Au, Ag, Cu, Pb, Zn, Mo) patterns in orientative rock samplings show that the studied alterations zones correspond to high sectors of the cpithermal system, without evidences of metallic minerali- zation on surface. The weak erosive action due to the ex- tremely and climatic conditions in this segment of the Andes, has not allowed the cropping out of deeper areas of the hydrothermal alteration zones, in contrast to other Miocene more eroded volcanic edifices and Miocene vol- canic terranes of the Andean Range.

Jan 1, 1987

By R Kerrich

Early-Archaean (3.26 Ga) volcanogenic massive sulphide (VMS) deposits located within the low strain and sub-prehnite-pumpellyite metamorphic-grade Strelley greenstone belt, East Pilbara, Western Australia, contain exceptionally well preserved sulphide textures which are directly analogous to those of sulphide chimneys formed by black smokers at present day submarine hydrothermal vents. The VMS deposits are associated with seafloor alteration zones in and below silica-carbonate laminites, at the top of tholeiitic to calc-alkaline intermediate and felsic rocks. VMS mineralisation comprises stratabound Zn-rich sulphide lenses with significant Cu and barite, and variable Pb and Ag, above Cu-rich stringer zones, all of which are similar to Phanerozoic polymetallic or Kuroko VMS deposits. Sulphide-sulphate mineralisation implicates hydrothermal discharge into sulphate-bearing ocean waters, ruling out a globally anoxic Archaean hydrosphere. The volcanic rocks and co-magmatic sub-volcanic intrusion hosting the VMS deposits are characterised by the conjunction of LILE>LREE>HREE, and Phanerozoic La/Yb with negative normalised anomalies of Nb, P and Ti, consistent with derivation via subduction zone hydrous metasomatism fusing the mantle lithosphere.

Jan 1, 1995

In most surface mining operations, overall project economics is driven to a significant extent by the slope angles that can be achieved within the rock masses present. This is particularly true of precious metal pits in which stripping ratios can be relatively high, although examples from other non-precious metal operations (such as large iron ore and copper pits) can also be found. As a consequence, it is not surprising that in most large (deep) open pit mines, relatively small changes in slope angle (of the order of two or three degrees can translate into changes in project value measured in the tens or even hundreds of millions of dollars. Understanding how this potential value can be realised, and quantifying the associated risks, should be one of the key outcomes of modern slope engineering practice. In striving for optimised slope angles, therefore, mining companies and their specialist consultants are increasingly turning to more sophisticated methods of engineering open pit walls. This paper summarises contemporary slope engineering practice as well as some of the key technical issues that are either currently being researched or will need to be researched in the future. It is written in the context of the slope engineering process; namely, data collection and analysis, failure mode identification and stability assessment, slope design, slope formation, and slope (face) mapping and monitoring (the latter two activities being the primary on-going data collection functions that close the design loop).

Jan 1, 2002

By T Rock

This paper looks at recent advances in the United Kingdom (UK) tunnelling industry with particular reference to the A3 Hindhead Project. A 1.8 km long twin bore tunnel is the centrepiece of the A3 Hindhead scheme, which commenced construction in 2007 and is being delivered under a UK Highways Agency early contractor involvement (ECI) contract. The proposed construction methodology is progressive mechanical excavation of a horseshoe-shaped tunnel with shotcrete installed close behind the face using robotic spraying equipment. The tunnelling medium is a æsoft rockÆ sandstone for which there was little previous tunnelling experience, requiring extensive geotechnical investigations and an innovative approach to lining design. A 240 m long section though sandy material utilising a steel pipe umbrella is also required. This paper describes the development of the tunnel planning and design including the most recent developments in UK road tunnels. The innovative approach to the design of the following is discussed:the æpermanentÆ primary lining,an observational technique allowing optimisation of the steel pipe umbrella design,a plain concrete secondary lining designed for resistance to a hydrocarbon fire, anda spray-applied membrane.

Jan 1, 2008

An Investigation into the Flotation Behaviour of Pyrrhotite Present in the Merensky Orebody

Sep 13, 2010

By W T. Yen

Pyrrhotite crystallises as either a hexagonal or monoclinic structure, both of which can occur in ore deposits. In general, pyrrhotite is not considered as a valuable mineral unless it contains considerable amounts of other metals like nickel or copper. In fact it causes numerous problems in flotation including intensive oxygen consumption, which results in poor selectivity among sulphide minerals in the processing of complex sulphide ores. Also, because of its high sulphur content, pyrrhotite is a major contributor to environmentally detrimental sulphur dioxide (SO2) emissions from smelters. Pyrrhotite also interacts galvanically with grinding media via electrolyte species present in the flotation pulp, resulting in media corrosion. The most effective way to reject pyrrhotite is through a separation stage, which may be difficult when both types of pyrrhotite are present in the ore. In this regard depression of pyrrhotite through a flotation stage may be applied. Pyrrhotite depression by either intensive oxidation or by using sodium cyanide has been practiced. Results present in this work show that NaCN can depress pyrrhotite effectively when combined with an alkaline environment and low collector concentrations.

Jan 1, 2002

By D J. Corp

The Halmahera Contract of Work is a sixth generation contract held 82.5 per cent by Newcrest Mining Limited and 17.5 per cent by PT Aneka Tambang and takes in the Gosowong Project area. In 1991 Newcrest Mining Limited established a small exploration office in Jakarta and proceeded to seek exploration opportunities. The Halmahera area was identified as a substantial prospective ground position in a relatively unexplored area. In late-1991 Newcrest Mining Limited and PT Aneka Tambang agreed to explore in Halmahera. Initial field work commenced in July 1992. A vigorous ground reconnaissance programme led to the discovery of the Gosowong deposit a little over 12 months later in September 1993. In April 1997 the Contract of Work was approved covering much of the island of Halmahera. Between September 1997 and November 1998 activities were directed principally towards obtaining the necessary permits required to commence construction activities. Some particularly ambitious targets were set for achieving this outcome. An aggressive construction programme commenced in late-1998. Construction took place during a period of unseasonally high rainfall, which in itself presented additional challenges to the construction team. A key milestone for the project was achieved on 1 July 1999 when wet commissioning of the process plant commenced. Construction of the Gosowong Mine was achieved on time and within budget. A period of some six years elapsed from the initial discovery of the Gosowong deposit to the time of the first gold pour. Much of the permitting, construction and commissioning activity took place between September 1997 and July 1999. This coincided with a period of significant social, economic and political upheaval in Indonesia. During the construction period a high level of importance was placed on the structured recruitment and training of local people, as well as fostering appropriate community and local business development programmes in the communities nearby the project. Emphasis was also placed on environmental management with detailed long-term planning and progressive rehabilitation commencing during the construction phase. The permitting and subsequent development of the Gosowong Project has demonstrated that even during the difficult times, with commitment, it is possible for mining and exploration companies to conduct business in Indonesia.

Jan 1, 1999

By S Sabanov

Determining ventilation system model inputs from the field test work has been produced in the working oil shale mine which has been in production since the early 1970s. At this mine room-and-pillar with drill-and-blast methods are used. The mine has a complicated ventilation system to supply fresh air for the eight mining production areas on the radius of about 12 km. The main purpose of the experimental test works was to obtain data for estimation of an optimum cross-section area for a new ventilation shaft. Experimental test works included measurements of air volume and fan pressure using five different modes of intake air through the ventilation shafts system. Measurements of airway friction factors were obtained during the ventilation surveys to determine characteristic friction factors for the intake airway. The results of the measurements will be used for further air flow simulation processes required for design of new additional ventilation shafts in the oil shale mine. Results of the study can be useful in estimation of frictional pressure drop in oil shale mine conditions.CITATION:Sabanov, S, 2017. Determining ventilation system model inputs from field test work in the oil shale mine, in Proceedings Australian Mine Vent Conference 2017, pp 47–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By W C. Burton, J S. Kuszma, T O. Aspinall

The environmental impact of mining and evolving environmentallegislation has received increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental regulatory agencies and members of the public. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. There is thus the need to increase the base of knowledge on the existing practices of spoil dump design and rehabilitation. Efficient engineering design and systematic economic evaluation of spoil dump reshaping techniques for mine rehabilitation assists in maintaining the expected standards of environmental compliance. As part of the overall approach for effective engineering design ofspoil dumps, a comprehensive, computational and efficient tool isrequired for assessing the economics and productivity of existing spoil dump reshaping practices for efficient mine rehabilitation. Such a design tool is useful in linking current spoil dump environmental management practices with engineering design planning and economic impact evaluation. This paper identifies the processes for the economic impact evaluation for existing spoil dump reshaping practices and proposed final site dump designs. Selection of an efficient spoil dump design at optimum costs will ensure operational efficiency. A case study is presented identifying economic impact evaluation in earthmoving equipment selection and the costs involved for the reshaping of spoil dumps to that of varying final site designs.

Jan 1, 2000

By K Thorpe

Amorphous silica deposits have been identified at Tikitere and Taheke near Rotorua. Two areas at Tikitere have been surface sampled and drilled to establish a resource of amorphous silica in excess of one million tonnes. A pilot plant was established to develop a process to manufacture a high quality super pozzolanic material. This development process took two years before a commercial product was introduced to the construction industry in 1996. The amorphous silica product, marketed as Microsilica 600, is used as a pozzolanic material to produce high quality strong and durable concrete, sprayed tunnel linings, mortars and grouts. Microsilica 600 has been used locally and exported to 11 countries.

Jan 1, 1999

By C Bailey, T Kojovic, M M. Hilden, M S. Powell

The Julius Kruttschnitt semi-autogenous grinding (SAG) mill model was developed by Leung in the 1980s and extensively updated to the variable rates model by Morrell and Morrison in 1996. Since then only minor upgrades have been incorporated in the version distributed in the JKSimMet simulator. A number of improvements, developed over the course of the AMIRA P9 project and in recent independent work, have now been incorporated. These improvements are based on a power-based model that directly relates the degree of breakage with energy consumption. The new size-dependent breakage function has been incorporated. The upgrades include more accurate predictions for a wide range of mill fillings (ten - 40 per cent), slurry hold-up in the mill, pebble discharge rate and the influence of changes in feed size and ball load.The paper presents the status of progress in the model development. The upgraded model will greatly enhance its application to challenging design and optimisation studies required to optimise the performance of SAG milling circuits.CITATION:Kojovic, T, Hilden, M M, Powell, M S and Bailey, C, 2012. Updated Julius Kruttschnitt semi-autogenous grinding mill model, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 71-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

In eastern China, most of the copper skarn deposits occur in folded troughs which are controlled by the EW-trending faulted fold systems (the Pal-Asian geotectonic domain), and the NNE-trending rift or fault zones (the Marginal-Pacific geotectonic domain), particularly the later. From the north to the south, there are four troughs hosting the main copper skarn deposits in eastern China: the Yanliao Trough, the Yangzi River Trough, The Qiantang-Yuanshui Trough and the Zichen Trough. There are more than 30 copper skarn deposits in eastern China, and ore reserves of each deposit are between 30 to 100 Mt with average grades over 1% Cu.    Most of the large copper skarn deposit-related intrusions are Mesozoic in age (170 to 100 Ma) and were emplaced during the Yanshanian Movement. Outwards from the intrusion bodies, both the skarn alteration and mineralisation show certain patterns of zonation. Mineral assemblages indicate a relatively high oxidisation state during metasomatic alteration and mineralisation. Sulphur isotopic work indicates that most d34S values of the sulphides are between ~4 to 3ë suggesting a common magmatic sulphur source. Fluid inclusion and oxygen isotopic studies suggest that early-stage fluid shows magma-related fluid characteristics although meteoric water was involved during late-stage alteration.

Jan 1, 1995

By R C. A Minnitt

This paper illustrates the use of variography and moving average plots as an aid to analysing variations in the process that can be used to direct the improvement efforts. The hydrometallurgical processes used in manganese metal production consist of sequential unit operations that include milling and reduction of manganese ores. Leaching of the reduced ore, is followed by solid-liquid separation, residue disposal, solution purification and electrowinning of manganese metal completes the process. The nearly 250 integrated process control loops rely on reports of pH, flow pressure, level, temperature and chemical analyses. Metallurgical accounting, reconciliation and process control is achieved through monitoring of the chemical and mass balances within the manganese reduction plant, requiring approximately 50 000 analyses of solids, powders and liquids each month. The largest numbers of samples are taken in the cell house. Changes and variations monitored by sample statistics ensure that the manganese products comply with predetermined specification limits. Optimising the information-value of the approximately 50 000 samples in the manganese plant is carried out in tandem with ongoing process optimisation. Variographic analysis of daily sampling data suggests that the cyclical behaviour evident in the moving average plots is only a reflection of random residual variability and not a reflection of true underlying variability related to cyclical phenomena. Low resolution in the variogram of daily sampling data masks the short-range variability that emerges when hourly data are analysed. Hourly samples collected over a 39-day period (giving 941 sample data), helped identify short-range cycles in the process. The relative distribution of variability for daily sample intervals, indicate that 57 per cent arises from V[0], 18 per cent from V[process] and 16 per cent from random residual variation. V[0] includes all the uncontrolled sampling error arising from a poor sampling protocol, the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. This confirms the suspicions regarding the suboptimality of the sampling protocol and the way it is implemented. The absence of long-term trends in the leach suggests that short-term variation (less than one day) dominates the process. While the control charts indicate that the overall processes are maintained above the lower specification limits and the target values, there is nevertheless a considerable amount of variability in the system that overhangs the processes and threatens to impact them negatively. Although the variability in the leach is above the prescribed limits, the volatility is a matter of concern because it seems to be uncontrolled. The comparison of the various sources of variability in data collected on an hourly basis suggests that the short-term random variability (V[0]) accounts for almost 50 per cent of the variability in the process. The main source of this variability is due to errors in the sampling protocol and is probably related to the size of the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. Remediation of FE and GSE will probably lead to a reduction in V[0], whereas V[process] could be mitigated by reducing the biases associated with DE and EE in particular.

Jan 1, 2008

Application of the Anaconda Simplified Work Index for Multiple Test Sizes Vale uses Bond Work Index measurements extensively in a number of applications. The Bond Work Index is usually a good parameter for checking scale up procedures when sizing ball mills, as well as the basis for variability analysis whenever drill core data is available. It is typical to measure between 100 and 150 Bond Work Indexes, depending on the deposit characteristics. The Bond procedure is relatively complex and time costly. It also requires relatively large amounts of sample, which are very expensive to be obtained. The benefits of the Anaconda simplified procedure are: considerably smaller sample requirements and laboratory time. This makes it very much attractive at Vale's development centre, including geometallurgical mapping, operation efficiency control, mine to mill, etc. The Anaconda simplified procedure was implemented and evaluated at Vale's Development Centre using a number of ores and several samples of each ore totalling more than 190 measurements. The Anaconda simplified method was calibrated for several test sieves and a correlation for any test size was determined for Vale's test mill. The calibration was also extended for two sample top sizes. The relative error of the simplified procedure was found to be in the range of nine per cent which is within the expected error Bond standard procedure. The implementation of the Anaconda method at Vale's development center has been used with great success over the past years in several green field, brown field projects and operating plants.

Sep 13, 2010