Search Documents

By L. Valentik

Many attempts have been made during the last 40 years to evaluate the performance of gravity separation equipement, that is, the effectiveness with which light and heavy particles are separated. The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris in 1950. The methods suggested by the Conference were accepted and very widely used in the last two decades. This paper discusses an improved method of evaluation in the light of the now-accepted standard presentation. The float-and-sink analysis of the product is presented on a Gaussian distribution curve, resulting in an easier visualization of the inherent difficulties of separation. The ogives of the distribution curve me then plotted, giving a quantitative measure of the deviation from perfect separation as an error distance instead of an error area. Illustrations of the new method are given both for gravel and for coal preparation, but the content is valid and applicable to other types of minerals which are separated by gravity methods. Many attempts had been made during the last forty years to evaluate the performance of heavy-media separation (HMS) equipment, that is, the effectiveness with which floats and sinks are separated.'-' The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris. 6 The primary aim was the thorough understanding of the mechanism of separation and the unified presentation of data on gravity separation so that the evaluation and comparison of washery performance could be made from all over the world. No strict overall standardization has been achieved, but after the conference a more or less uniform presentation of performance was accepted, which, during the last two decades, has been very widely used. In this paper, illustration of the old methods and an improved method of evaluation will be given. HEAVY-MEDIA SEPARATION (HMS) PERFORMANCE CRITERIA In the ideal HMS process, all material lower in density than the specific gravity of separation (SGS) would be recovered as floats and all material of higher density would appear as sinks. In order to evaluate the misplaced material, the washery products are tested at the density at which the washing unit is operated. The original type of plot1,7, 8 is shown in Fig 1; this was developed primarily for coal cleaning units. The curve for raw coal represents the cumulative percentages of sink material. The refuse curve is also plotted as a cumulative sink, the percentages being expressed in terms of raw coal. This diagrammatic representation of the results of washing units has the merit of easy visual observance of the degree of separation obtained. The error areas (cross-hatched) are a measure of the amount of misplaced material and therefore they can be used to characterize the quality of separation. The ideal and actual separating performance between floats and sinks can be best seen from the partition curve developed by Tromp,2 where the ordinate is the percentage recovery of the sinks, and the abscissa is the specific gravity (Fig. 2). It can be seen from the shape of the curve that as the SGS is approached, the proportion of material reporting to the improper product increases rapidly. In fact, the SGS can be defined as the density of the material in the feed that is distributed equally between float-and-sink products. When the upper half of the curve is inverted, a shape similar to that of a Gaussian error distribution curve is obtained and therefore the analysis of gravity separation may be carried out by using the law of probability. The shape of the curve in Fig. 2 is determined partly by the density composition of the feed, and partly by the sharpness with which the unit separates floats from the sinks.9, l0

Jan 1, 1970

By B. K. Larkin, H. R. Bailey

A model Of heat flow in an underground combustion process is studied. This model includes convection effects and thus is more general than previous studies which considered conduction as the only mechanistn for heat transfer. Both linear (tube run) and radial (field application) geometries are considered. The effects of ignition heaters, vertical losses and finite source width are considered for the linear case. The results are in the form of equations and are presented in graphical form for a number of cases. Convection effects increase frontal temperatures about 25 per cent over those computed for conductive transfer for typical field operating conditions. This increase in temperature is a result of heat being transported toward the front by the injection gas. Even greater temperature increases are realized as the per cent oxygen in the injection gas decreases. It is well known that compression costs are of considerable importance in estimating the economic feasibility of underground combustion. By assuming an ignition temperature for the combustion fuel, predictions of limiting conditions on fuel density and injection rate necessary to sustain the combustion zone are made. For typical field conditions, at least 0.75 lb/cu ft of fuel are needed with air as the injection gas. If the injection gas is 10 per cent oxygen and 90 per cent nitrogen, this figure is 0.69 lb/cu ft. INTRODUCTION The possibility of increasing oil recovery by underground combustion has been considered for many years. Recent field tests indicate that the underground combustion process is technically feasible. The economic feasibility depends to a large extent on the amount of air which must be injected to sustain combustion. Prediction of the success of employing underground combustion in a particular reservoir must be based on existing field tests, laboratory tube runs"' and solutions of mathematical or analog models. Vogel and Krueger5 devised an electrical analog of the heat transfer problem in an underground combus-ion process. They considered the problem of heat conduction from a cylindrical source with increasing radius assuming no vertical losses. Bailey and Larkin and Ramey solved the corresponding problem including vertical losses by considering a mathematical model of the conduction process. Ref. 9, 10 and 11 also present information related to the subject study. The present paper generalizes these results to include both conduction and convection mechanisms for heat flow. A model of the conduction-convection process is described. The partial differential equations governing this model are written and solved for a number of cases of interest. The formulas are evaluated and the results are presented graphically. A CONDUCTION-CONVECTION MODEL Description of the Model A number of models are employed in this paper, each of which approximate a particular physical situation depending on the geometry, i.e., linear or radial flow, the type of vertical heat losses, the nature of the source, etc. The geometry for both the linear and radial case is shown in Fig. 1. A particular linear model is described in this section, and variations from this model are described in later sections of the paper. Consider a homogeneous, semi-infinite porous prism with lateral sides insulated as shown in Fig. 1. The left end, x = 0, is heated for a time t, with a plane heater supplying a constant heat flux and during this time; gas (nitrogen) is passed through the pores of the prism at a constant mass flux. At time t, the heater is turned off and air is injected in place of the nitrogen. This causes combustion to take place, and a uniform source of width 1 is formed which moves at a constant velocity v, to the right. The frontal velocity v, is related to the gas velocity v,, through stoichiometric considerations

By O. D. Gonzalez, R. A. Oriani

A thermo-osmosis technique has been used to measure the heat of transport, Q* , of hydrogen and of deuterium dissolved in a iron and in nickel, and of hydrogen in Feo.6Nio.4 in the tempevature range 400° to 600°C. For all these systems, Q* is negative and has a large temperature coefficient; an isotope effect can be established for the solutes only in nickel. The magnitude of Q* is considerably larger than the activation energy, E , for migration in the case of these isotopes in a iron, so that all variants of the Wirtz model must be rejected. The phenomenological definition of Q* is developed to show that Q* is related to the mechanisms by which the activation energy is dissipated back into the lattice, and that Q*/E is a function of the ratios of the mean free paths of electrons and of phonons to the distance of jump of the diffusing atom. A correlation is shown to exist between the sign of Q* in thermal diffusion and that of the effective charge in electro migration, and may be understood as due to the large ratio of the mean free path of electrons to that of phonons. THE study of nonisothermal diffusion in the solid state is of interest because certain aspects of the mechanism of diffusion are made manifest which remain concealed though still present in the isothermal case. The thermodynamics of irreversible processes characterizes nonisothermal diffusion, known as thermal diffusion or as the Ludwig-Soret effect, by a quantity, Q*, called the heat of transport, which essentially measures the sign and the magnitude of the steady-state concentration gradient produced by the imposed temperature gradient. The problem then is to understand the quantity Q* at the atomistic level. There does not exist a theory for the atomistic interpretation of the heat of transport. There are, however, two classes of simple models which seem to afford some physical insight into Q*. Wirtz's model1, z and its subsequent generalizations partition the activation energy, E, for the migration of the atom spatially about the region of the migrating atom, so that Q* is the difference between the portion of the activation energy centered about the original site of the jumping atom and that portion about the arrival site. Clearly, the magnitude of Q* cannot on this model be larger than the activation energy for migration. The model of Oriani3 also considers the spatial distribution of E not only before but also after the atomic jump, and Q* is related to the variation of the spatial distribution of E that is produced by the jump. The simplest kind of system with which to compare the consequences of these ideas is the interstitial solid solution, since one may easily choose a temperature at which only the interstitial component moves, the solvent lattice serving as a completely satisfactory frame of reference. Thus, one avoids complications arising when both species in a binary system move. In addition, one avoids the necessity of knowing the energy for the formation of a vacancy, something which is needed for the analysis of thermal-diffusion data on metals which diffuse by the vacancy-exchange mechanism. However, the number of well-measured interstitial systems is extremely small, and, in particular, there are almost no data in the published literature for the temperature dependence of the heat of transport. If one works with solutes which are gases in the pure state at ordinary temperatures, one may use the technique of thermo-osmosis4 which permits thermal diffusion to be measured over a small temperature difference so that the temperature dependence of Q* can be more easily determined. The choice of dissolved hydrogen in iron and nickel was based on these considerations as well as on the desire to look for an isotope effect associated with localized

Jan 1, 1965

By F. W. Jessen, G. F. Sears

Cavities in massive salt for the purpose of storage of liquid hydrocarbons have assumed a prominent position in recent years. This paper describes a program to facilitate leaching operations for the formation of specifically shaped storage cavities. Various forms and sizes of cavities may be possible through use of the techniques developed. INTRODUCTION The creation of large under ground storage facilities for natural gas and liquified petroleum gases has been practiced for many years. Use of cavities obtained through solution of salt for this purpose is a fairly new and novel approach, but has gained increasing importance due mainly to the economics of this type of mining operation opposed to hard rock mining or surface and pit storage.1 The idea of controlling the shape of any cavity dissolved from massive salt has not been a prime consideration of companies engaged in the formation of storage space. This has been due mainly to an insufficient knowledge of the mechanics of the leaching process and a dearth of published information dealing with both the desirability and ease of control possible for this type of operation. Two distinct advantages are readily ascertainable. From a stability standpoint (i.e., the ability of the completed cavity to withstand stress imposed by overburden pressure and lateral tectonic stresses) a controlled cavity may be generated which will yield the most favorable attitude to these external forces and remain in operable use for longer periods of time.2 A second advantage is that for a given volume, a sphere (which is one controlIed shape possible) represents the minimum surface area exposed. This may become more important in the future when dealing with refrigeration and product losses in underground cavities. The basic solution mining process, without regard for controlling the final shape, is quite simple in that the equipment and materials required to dissolve a cavity in a salt dome or layered salt section are a source of fresh water, a circulating pump, several strings of tubing and a means of disposal of the return brine. To add control measures involves the use of an inert blanket material above the position at which solution proceeds. Initially the annulus of the largest wash pipe is filled with this blanket down to the top of the proposed cavity. The bottom of the proposed cavity is determined by the depth of the original drilled hole or a blanking plug. The blanket material is added incrementally in stages and displaces the water in the enlarging cavity downward. Where the blanket material has displaced the water, no further solution takes place. The rate at which to add this controlling blanket material so as to be able to form specifically shaped cavities of any particular size is of considerable importance. THE PROBLEM It is desirable to have as much information as possible as to the behavior of the mining operation since visual observation obviously is impossible. It would be advantageous, for example, to have a step-by-step program showing how much salt is to be removed, at what rate and the time required. This type of program would facilitate procurement of surface equipment and provide for proper management of manpower requirements, as well as yield a host of intangible benefits. As mentioned earlier, only rule-of-thumb estimates were available until recently and made this type of pre-planned operation haphazardous at best. Recent work3-' has done much to clear up the ambiguities and inaccuracies attendant to solution mining of salt and has helped to place the operation on a more scientific basis. This study attempts to correlate much of the information thus far developed into a complete mining program; to extend the idea of controlled solution mining to include not only spheres, but solid conic sections of the ellipsoidal variety; and to refine the computation of the rate of removal of salt during the various stages of mining. Dommers3 and IIemson4 made extensive laboratory

Jan 1, 1967

By R. L. Schmidt, J. D. Verhoeven

The diffusion coefficients and electrotralzsport mobilities of aluminum, gallium, and arsenic have been determined in molten germanium with the capillary reservoir technique. The diffusion coefficients are slightly higher than those determined by the solidification technique of Brirton et a1.1 It was found that aluminium and gallium migrate to the cathode in molten germanium) whereas arsenic migrates to the anode under an electric field. A possible technique for producing p-n junctions by means of electric field freezing is discussed in view of the experimental data. In the past decade or so the literature has abounded with articles concerning the solid-state properties of the semiconducting elements germanium and silicon. It is surprising by comparison how little has been published concerning the liquid-state properties of these materials. In the production of doped germanium or silicon the diffusion coefficient of the dopant in liquid germanium or silicon is an important quantity. Yet, to the best of our knowledge, no one has ever made a direct measurement of the diffusion coefficient of solutes in either molten germanium or silicon. A number of authors'-4 have determined some diffusion coefficients by the indirect technique developed by Burton et al.1 This technique appears to give numbers of the correct order of magnitude but it does depend upon a number of assumptions in the analysis and also requires prior knowledge of the viscosity of the melt. In the present work a more direct measure of the diffusion coefficients of arsenic, gallium: and aluminum in molten germanium has been made. It has been shown independently by two groups of authors5, 6 that, when an electric current is passed through the interface of a solidifying metal containing an impurity, the resulting electrotransport in the liquid boundary layer at the interface offers a mechanism for control over the redistribution of the impurity accompanying the solidification. These authors show that the degree of control is proportional to the mobility, U of the impurity atoms in the liquid boundary layer, where the mobility is defined as the drift velocity relative to the solvent per unit electric field. In principle the results apply to the solidification of a doped semiconductor and offer an interesting technique for control of the doping of a semiconductor. In the present work the mobilities of aluminum, gallium, and arsenic were determined in molten germanium in order to evaluate the potential usefulness of electro-transport as a technique for solute control when applied to the solidification of doped germanium. EXPERIMENTAL PROCEDURE Both the diffusion coefficients and the mobilities were measured using high-purity alumina capillaries and a resistivity technique for analysis. A schematic diagram of the electrotransport apparatus is shown in Fig. 1 and the details of the cell design are shown in Fig. 2. For the mobility experiments electrical contact with the bottom of the capillary was made with graphite, as shown in Fig. 2. In order to prevent electrical contact with the melt the graphite was coated with a thin layer of alumina using a plasma spray torch. The cell assembly, a graphite electrode, and another assembly containing two blank capillaries were fastened to the lavite disk shown in Fig. 1. To make a run the system was evacuated and the doped germanium was outgassed at the operating temperature of 1030°C. The cell and blank capillaries were then submerged beneath the melt and a slightly positive pressure of helium was introduced to fill them. After passing current through the cell for a given time the cell and blank capillaries were raised from the melt and the furnace was shut off. The temperature of the cells dropped below the freezing point of germanium within 1 to 2 min after the furnace was shut off.

Jan 1, 1968

By K. T. Koone, R. J. Blackwell

One of the more important problems to be solved in designing a miscible flood is related to the size of the solvent bank used. Size of the bank may be critical to economic success. Too large a bank loses money; too small a bank may deteriorate and fail to maintain the miscibility needed for high recovery. An important factor in deterioration of a small bank is permeability channeling. In a highly stratified reservoir, solvent speeds ahead in the more permeable zones and mixes laterally with fluids bypassed in adjacent, low-permeability strata. Numerical solutions have been obtained .for the differential equations that describe the movement of a slug through a two-layer system in which mixing occurs both in the direction of flow and transversely. The solvent slug is assumed to have the same density and viscosity as the resident fluid and the pushing fluid. These solutions have been verified by comparing them with similar concentration profiles obtained in the laboratory in a 36-ft stratified model packed with glass beads. The theoretical study revealed that when the dominant mechanism causing a bank to fail is lateral mixing the bank size needed for a given recovery may increase with length rather than decreasing as the square root of reservoir length, as suggested by one-dimensional mixing theory. From a comprehensive examination of the variables, a generalized correlation is developed that relates strata thicknesses, bank size, fluid velocity, mixing coefficients, system length and simple solvent-resident fluid phase behavior to the area miscibly swept. INTRODUCTION Miscible displacement, or solvent flooding, continues to receive widespread attention as a method for increasing oil recovery over that possible in conventional gas-drive or waterdrive projects. A basic economic requirement in the application of such processes is the use of as little solvent as possible. A basic physical requirement is that enough solvent be used to maintain miscibility. Economics places an upper limit on the size of a solvent slug, and physical considerations establish a lower limit. Consequently, the practicality of any given miscible process requires that the economic limit be greater than the lower limit imposed by physical requirements. Procedures exist for determining the economic limit; however, procedures for determining realistic minimum bank sizes exist for only special reservoir situations. In the past, bank size has usually been selected on the assumption of a piston-like displacement for which only longitudinal mixing is important. This assumption leads to the favorable conclusion that bank size, expressed as per cent of pore volume, is inversely proportional to the square root of length. Collins considered the problem of transverse mixing of solvent with fluids in bypassed zones with the assumptions that no forward mixing occurs and that the concentration is uniform in the permeable stratum of interest. 1 Lauwerier considered a mathematically similar problem in thermal recovery operations.2 Their work suggests the much less favorable conclusion that bank size could be directly proportional to the length or even higher powers of the length. This paper considers the physical behavior of a small solvent bank as it moves through a real reservoir, without imposing many of the restrictive assumptions of past treatments. To facilitate mathematical description, an idealized, two-layer model that permits mixing both laterally and in the direction of flow will be considered. A calculation procedure for solving the descriptive equations will be developed for a displacement involving fluids of equal density and viscosity. In addition, laboratory experiments designed to check the computational results will be described, and the coincidence of calculated and observed results will be discussed. The use of many solutions for a variety of bank sizes, strata thicknesses and characteristic system lengths to develop a usable correlation between

Jan 1, 1966

By R. L. Jones, H. Conrad

The effects of gain size on the room-temperature tensile properties of commercial(A- 70)-purity and iodide-purity titanium were investigated by concurrent tensile testing and thin-foil electron transmission studies. The mechanical tests showed that the effect of grain size on the yield, flow, and fracture stresses could be expressed by relations of the Hall-Petch type. The magnitude of the grain size effect on the yield stress was larger for commercial-purity than for high-purity titanium, but in both materials it was intermediate between that typically observed for fcc and for bcc metals. The effect of strain on the gain size sensitivity of the flow stress was found to reflect the grain size dependence of strain hardening. The electron transmission study indicated that the tensile behavior could be accounted for in terms of the dislocation densities and distributions formed during deformation. It was concluded that the effect of grain size on strength could be attributed to a relationship between grain size and the dislocation densities generated in initiating and sustaining plastic flow, the difference in stress levels being due to strain hardening. The relationships between recrystallized grain size, uniaxial tensile properties, and dislocation substructure have not been explored in any detail for a titanium. With titanium and its alloys finding increasing applications in aerospace systems, such information has become essential. The research described in this paper had two objectives: first, to document the effect of grain size on the yield, flow, and fracture stresses of unalloyed a titanium by the tensile testing of recrystalliied specimens at room temperature; second, to attempt an interpretation of the mechanical test behavior in terms of the dislocation structures formed on deformation, as observed by transmission electron microscopy of thin foils prepared from deformed tensile specimens. The observations reported here are restricted to room-temperature deformation; the effect of temperature on the yield and flow stresses of a titanium and the athermal nature of the contribution of grain size to the flow stress have been discussed elsewhere.1"3 EXPERIMENTAL DETAILS Two purity grades of unalloyed titanium have been investigated: Crucible Steel A-70, a typical commer- cial-purity product, and a high-purity iodide grade supplied by the Foote Mineral Co. Chemical analyses for interstitial impurity contents are given in Table I, together with values for the total interstitial atom fractions in terms of oxygen equivalents, which were calculated by the method outlined previously.4 ,5 According to the manufacturer's nominal analysis, the A-70 grade also contains about 3700 ppm of Fe. The A-70 grade was supplied as 1/4-in.-diam centerless-ground rod. The iodide grade was supplied as crystal bar which was consolidated to approximately 1/4-in.-diam rod by a single, rapid, molten zone pass, using electron beam heating. The 1/4-in. rods were cold-swaged to 0.078-in.-diam wires and 2-in. lengths were recrystallized in a vacuum of -5 x 10-5 torr, giving grain sizes in the range 0.8 to 30 . The thermal treatments and resulting grain sizes are summarized in Table 11. Since there was in no case any obvious sign of a bimodal dis tribution of grain sizes, the grain size values quoted in Table I1 are those obtained from mean linear intercept measurements involving >I00 grains. For the two coarse grain sizes the measurements were made using conventional optical techniques. It was noted during these determinations that the etchants used (10 pct HF; 30 pct HN03; 60 pct H20 and 2 pct HF; 2 pct H202; 96 pct H20 were both tried) etched grain boundaries very nonuniformly and optical polarization effects had to be employed to reveal boundaries which might otherwise have been missed. It was found that this problem became more acute with the finer grain sizes as the usefulness of polarization diminished.

Jan 1, 1970

By S. V. Krusiewski, J. W. Gabelman

Regional metallogenic zones and areas of equal paragenetic range have been interpreted from a compiled metallogenic map. of Mexico. Mineralization gradients of the pattern subsequently identified extend inland from coastal zones of high-temperature mineralization, and join in a central longitudinal zone of relatively low-temperature mineralization, apparently leaving no zonal room for lowest temperature deposits. The striking regional zoning pattern can be correlated with regional deformation gradients of similar position and orientation. The gradients represent at least three major orogenic cycles in two structural belts. Paleozoic structural belts existed along each coast with deformation gradients diminishing inland toward a narrow, central peninsular craton. The Mesozoic-Tertiary Mexican (Cordilleran) belt covered the entire country with a gradient oriented toward the Gulf of Mexico. Most ore deposits in this belt are of Tertiary age, although Tertiary mineralization gradients seem to have "inherited" the pattern left by Paleozoic tectonic gradients. Mineralization gradients can be used to identify the regions most favorable for the occurrence of selected metals. A metallogenic province is characterized by particular proportions of various metals, and the relative proportions can vary from province to province; but within any province the same intensity of mineralization would produce similar deposits in different places. Declining intensity of minetalization produces different kinds and sizes of deposits in zones that are concentrically arranged around sites of strongest rock alteration. On a regional basis, districts of similar average intensity of mineralization occur in zones that generally parallel some tectonic grain with the result that tectonic deformation has been designated a principal cause of mineralization. Variations in the type and intensity of deformation would determine the type as well as size of metal deposits. Mexico is especially favorable for such a study be- cause of its great abundance and variety of epi-genetic mineral deposits in various lithologic, structural and tectonic environments. The concept is also useful in recognizing portions of Mexico favorable for the occurrence of specific metals. METALLOTECTONIC ZONING IN MEXICO Theory: In studies of individual districts and groups of districts throughout North and South America, areal zoning of metal deposits generally seemed to respond to the paragenetic sequence of iron, gold, copper, zinc, lead, silver, antimony and arsenic, gold and fluorite. However, the definition of district zones is greatly obscured by contemporaneous or rhythmic deposition of metals, especially in the middle of the paragenetic range, and by the common superimposi-tions of different generations of metals. Zones could usually be distinguished only for groups of metals, such as early precious metals, base-metal sulfides, sulfosalts and late precious metals. The best defined zoning in a district is normally the spatial separation of the greatest volumes of altered and metallized rocks.' Exceptions are districts representing the high- and low-temperature extremes of the mineralization range where the former creates a matrix for the latter. In most districts the total quantity of alteration products is greatly in excess of, and appears to be roughly proportional to, the total quantity of metallization products. Subsequent to the bicomponent nature of each district, the most important mineralogical feature is the great excess of one to several metals or minerals which results in a district identifiable as one of predominantly gold, copper, lead-zinc, fluorite, etc., although a great variety of other elements may be present. The para-genetic range for the abundant elements in any district is only a portion of the entire possible range for all the elements representing the complete process throughout the region. Early during investigations of this type, it became apparent that the consistent bicomponent character of districts allows two methods for studying epi-genetic mineralization patterns. One is to identify and plot altered rock "pipes,"* which are easily recognizable in the landscape by their anomalous

Jan 1, 1969

By J. A. Hren, C. M. Wayman

RECENT investigators have noted anomalous behavior in the electrical resistivity of vanadium below room temperature. Rostoker and Yamamoto1 in studying the vanadium-oxygen system hypothesized that the body-centered-tetragonal phase existing from 15 to 34 at. pet O at approximately 800°K was really a low-temperature allotrope of vanadium that was stabilized by oxygen. In measuring the electrical resistance of cold-swaged vanadium rod over a range of temperatures, a small discontinuity was observed at approximately 240°K, supporting their notion of allotropy. However, the magnitude of the observed discontinuity was extremely small. Loomis and Carlson2 in studying the ductile-brittle transition in vanadium also made resistance measurements and reported a discontinuity near 200°K. More recently, White and Woods3 showed that the electrical resistivity from room temperature to approximately 100 °K was not linear and at variance with the Bloch-Griineisen law. Instead of finding a discontinuity, they observed a deviation from linearity below 200°K. In discussing their results they pointed

Jan 1, 1961

By Richard Addison, Ronald O. Cranor

Tailings dam construction and operation of Rosario Dominicana's gold/silver mine in the Dominican Republic is described. Impoundment of 8.5 kt/d of cyanide-process tailings is required in an intensive agricultural area which is also an earthquake and high rainfall zone. The earthfill embankment dam, incorporating internal gravel drains, is described together with methods of construction used. Methods of tailings transport, solution reclaim, and runoff water diversion that have evolved are discussed.

Jan 1, 1982

By AIME AIME

SINCE the preparation of the Fall Meeting announcement the Montana Section has extended an invitation to the members traveling to Spokane to make at least a short stop at Butte, en route. Accordingly, the train schedule below has been worked out as an alternative to that announced in the general circular. This will permit a half day in which to visit either mines at Butte or the smelter at Anaconda and an opportunity for an evening meal with our Montana members. An interesting time is assured either way and the chance to renew acquaintance with Butte friends will be well worth will

Jan 1, 1929

By Y. A. Topkaya

The placer gold occurrences at Sart Çayl, Manisa, Turkey, the legendary River Pactolus of King Croessus, were evaluated in this study to determine if this deposit contains sufficient recoverable value to justify development and exploitation. The gold occurs both in the upper Neogene conglomerates and the alluvium derived from these conglomerates. The total reserve in the whole region is estimated to be 500 million cubic metres. Samples were taken of the upper conglomerate and in the alluvium in an attempt to determine the amount and the physical nature of the gold. The gold in samples was recovered by screening out barren oversize followed by washing the sand and gravel through riffled sluices. The resulting sluice concentrate was later panned and amalgamated at site. Laboratory cyanidation testing of some samples for control purposes was also done. The average calculated free gold was found to be about 90-100mg/m3 and the size of gold flakes found was quite small. The field as well as laboratory testing of the samples of Sart Çay1 indicated that the potential reserves in this region could only be developed as a sand and gravel operation and the gold could be recovered together with the heavy minerals as a byproduct.

Jan 1, 1984

By Arthur S. Dwight

THE last decade of the 19th century was a peculiarly interesting one in. the annals of American metallurgy, especially as concerns the lead and copper- smelting industries; and it may be interesting to review briefly one of the outstanding incidents of that period, the development of the mechanical roasting furnace. I shall not pretend, in these reminiscences, to give with absolute accuracy the sequence of events or dates, nor to present a complete history of the period, but shall seek merely to 'sketch a more or less impressionistic picture with some of the underlying facts and causes as the recollection comes back to me and then point out how the present-day practice grew out of those activities. My acquaintance with the developments in Montana was based on occasional visits and general collateral information, but in Colorado I lived through the episode and was of it.

Jan 1, 1921

James DouGlas, New York, N. Y. (communication to the Secretary*):—In my paper on the Conservation of Natural Resources, I referred to the slow replacement of bee-hive ovens by the by-product ovens as a most notable instance of waste. And I quoted from Mr. Parker's report for 1906 an explanation given by him in accounting for the small production of by-product coke. It was that the market for the by-products of the coke-ovens was so limited that some of the ovens constructed were out of operation. His report on the manufacture of coke in 1908' does not record an improvement, and attributes the strange fact that we alone, of all the industrial peoples, delay the adoption of this cardinal improvement from the continuance of the same almost inexplicable cause. To quote again from his report, he says (p. 241): "The year 1908 was not marked by any notable gain in the construction of byproduct coking plants, though some new work was done. There was a net increase

Jan 1, 1910

.MAX ROESLER, Firmeza, Oriente, Cuba (communication to the Secretary?).-It is substantially admitted by all who have recently been in touch with these deposits that the orebodies lie in the fine-grained dark-green rocks, called diorite by most writers and diabasic by myself. The three points of disagreement concern the agency of included limestone blocks as causes of deposition, the agency of the

Jan 5, 1917

A. R. Ledoux,New York City: The so-called combination method " is generally used in assaying bar copper for silver. It has been modified from time to time. Briefly outlined

Jan 1, 1901

By John Fritz

TROUGH it is not a condition of the Award, the fact is that the John Fritz Medal never has been given to an engineer who had not already received one or more similar awards. This "medal for medalists," on the evening of April 20, was presented to Daniel C. Jackling at a special dinner held at the Union League Club in New York. The citation read "For notable industrial achievement in initiating mass production of copper from low-grade ores through the application of engineering principles." The present award recognizes the same accomplishment-the launching and guiding to the port of marvelous success of the Utah Copper Co., first of the so-called "Porphyries"-as did the award of the William Lawrence Saunders Gold Medal by the A.I.M.E. in 1930, and before that the Award of the Gold Medal of the Mining and Metallurgical Society of America in 1926. Following the custom a biography of the Medalist had been published in a small pamphlet as a supplement to the John Fritz Medal Book. T. A. Rickard was the au¬thor of the sketch of Mr. Jackling, an innovation being the placing of a copy of the booklet at the place of each of the diners. The committee in charge of the dinner consisted of two past-presidents: R. E. Tally, of the A.I.M.E., who was chairman; Bancroft Gherardi, of the A.I.E.E.; and Thaddeus Merriman, director of the A. S. C. E., the John Fritz Medal being a joint award of the four societies. Frederick M. Becket, President of the A.I.M.E., as chairman for the occasion, briefly stated the purpose of the dinner. He stressed his satisfaction that the award was symbolic of the cooperative professional activities of the four great national organizations of engineers. He introduced Francis Lee Stuart, past-president of the A.S.C.E. and now chairman of the John Fritz Medal Board of Award. Mr. Stuart outlined the history and purpose of the Medal established in 1902 in memory of John Fritz, of Bethlehem, Pa., one of the great pioneers of America's iron and steel industry, metallurgist, and president of the A.I.M.E. in 1894. Mr. Stuart called the roll of former John Fritz Medalists, three of whom, Ralph Modjeski, J. Waldo Smith, and Ambrose Swasey, were present to do honor to Mr. Jackling. He then introduced George Otis Smith, whose privilege it was to present the Medalist for 1933. Dr. Smith was the senior of the four A.I.M.E. representatives on the Board that last year selected Mr. Jackling for the honor. His speech follows in full.

Jan 1, 1933

By Joseph D. Weeks

Manganese has, until recently, been most highly esteemed as a good thing to keep out of steel. Its value in the process of mannfacture has been fully recognized, but after it has played its part in the crucible or the converter, then the less of it the better. It is true that the mission of this metal and its influence upon the character of steel has been a source of much controversy. Our own Holley, in one of his special reports on ferromanganese: I, states that ''it has been suspected by some, and believed by a few, while it is still denied by many, that manganese as an ingredient in steel has not only a body-giving and toughening influence, but a positive neutralizing influence upon any excess of hardening or cold-shortening substances, as phosphorus." In another paper on the same subject he states that " it should appear from such facts as we have that manganese toughens" the structural steels, "increases their soundness and prevents red-shortness." Notwithstanding these rather guarded assertions as to its value, the general belief, it will be found, is with Dr. Siemens, that manganese is " merely a cloak to hide impurities," and its presence in steel has been endured, not welcomed. But whatever may have been the difference in opinion as to the

Jan 1, 1885

By David M. Cregger

The performance of the nation's first geologic repository for Commercial High Level Waste will be evaluated in a variety of ways which will involve the use of the state-of-the-art thermomechanical computer codes. Elastic properties of the host rock and the materials surrounding the repository are required for this numerical modeling effort to assess both near- and far-field effects. Only limited laboratory testing is possible, however, making it extremely beneficial to expand the data base by calculating dynamic elastic properties from available geophysical well logs. Elastic theory dictates that for an isotropic solid there are only two independent variables in addition to mass density, namely the compressional velocity, the shear velocity, and Poisson's Ratio. Compressional velocity and density are readily measured by geophysical well logs or in the lab; the crux of the solution requires measuring or determining either the shear velocity or Poisson's Ratio. Examination of acoustic propagated shear waves measured during confined compression testing demonstrates that Poisson's Ratio is a fundamental lithology-dependent parameter. Once a rock mass is appropriately classified, application of the laboratory derived dynamic Poisson's Ratio will yield a continuous and reasonable in situ modulus from acoustic and density logs. For preliminary characterization and assessment of the mechanical properties of rocks within the subsurface, and for studies of rock quality, this method is sufficiently accurate. The general availability of acoustic and density logs from wells logged for other purposes has made the application of this method desirable.

Jan 1, 1984

By T. A. Rickard

A severely technical article, however well written, can not be an agreeable form of literature. It suffers from the defects of its qualities. One defect is a congestion of language, due to a multiplicity of adjectival nouns. The sentences are packed with words of unpleasing sound, charged with complex ideas, crowding one another so closely that the phraseology moves like an ice-pack in Bering Sea or a log-drive in a river; the undercurrent of meaning may continue to move, but the surface is obstructed. This verbal congestion is made evident by ugly compoundings, many of which are adopted by the technical writer in the mistaken belief that they give directness to his statements. For example: A unanimously approved scheme "A scheme unanimously approved" The continuous temperature record "The continuous record of temperature" To stimulate interest in synthetic plant construction "To stimulate interest in the construction of synthetic plants " In smelters reverberatory-furnace firing with powdered coal has been practised for a decade. "In smelting, the firing of reverberatory furnaces with powdered coal has been practised for a decade. " A tar consumption of one pound per ton "A consumption of tar at the rate of one pound per ton'

Jan 1, 1931