Search Documents

By R. E. Cole, A. M. Gaudin

OLEIC acid, a standard flotation reagent, has generally been preferred to other fatty acids. Because oleic acid differs from saturated fatty acids by the presence of one carbon-to-carbon double bond and because the flotation operation is one in which extremely intimate exposure of the reagent to oxygen is obtained, it appeared possible that the value of oleic acid as a flotation collector was related to the oxidizability of its double bond. To test this hypothesis, the floated mineral, fluor-ite, was leached with a solvent capable of extracting the adsorbed reagent and the extract was analyzed.' Results show that oleic acid is not oxidized during flotation, although some oxidation can be obtained if the flotation operation is repeated many times and if oxygen in place of air is employed as the gas during flotation. Incidentally, it was found that lino-leic acid which has two nonconjugated double bonds is not affected appreciably more than oleic acid. Linolenic acid which has three nonconjugated double bonds is measurably altered even during one flotation step, using air. The fatty acids used, from the Hormel Foundation, were of the highest purity. The quantity of fatty acids employed in each test was sufficient to float the mineral, but less than the theoretical amount required to form a monolayer at the mineral surface. The purpose of this limitation was to eliminate droplets of oil smeared on the adsorbate-covered mineral surface. The mineral was dried in vacuum at about 60 °C. Effective leaching was obtained by use of a solution of 1 pct hydrochloric acid in absolute alcohol. The extract was separated from the solvent by distillation, with final recovery of the extract in carbon tetrachloride. The identity of the extract was tested by a combination of analytical procedures including infrared spectroscopy, saponification number, iodine number, and index of refraction. At the outset, great hopes for accurate quantification of oleic acid oxidation had been entertained in regard to the method of infra-red spectroscopy. Unfortunately, because the double bond in the oleic acid is so sym- metrically located at the center of the molecule that it provides very weak absorption bands, accurate quantitative analyses were not obtained. Nevertheless, infra-red spectrograms suggested the absence of double-bond oxidation during flotation. Iodine number, semi-micro method, provided a critical test of the extent to which fatty acids oxidized during flotation, see Table I. The index of refraction was used in a qualitative rather than quantitative fashion, and its findings corroborated those obtained by the iodine-number method. It is concluded, in the case of fluorite and C-18 fatty acids having one or two nonconjugated double bonds, that there is practically no change of the fatty acid molecule or ion during the flotation operation. It would appear, therefore, that the extraordinary utility of these reagents is related to some property of the compounds other than the oxidizability of their double bonds. Acknowledgment The research reported herewith was sponsored by the Research Division, U. S. Atomic Energy Commission, and for this help the authors express their appreciation. Reference 'R. E. Cole: "Double-Bond Reactivity of Oleic Acid During Flotation." Thesis submitted in partial fulfillment of the requirements for the degree of M.S. at the Massachusetts Institute of Technology.

Jan 1, 1954

THE strike and dip of bedded formations is readily determined by trigonometry if some marker horizon is intercepted by three holes. If no marker can be identified and if orientation of the cores is unknown, as is the usual case in diamond drilling, the determination still can be made readily by the use of a stereonet if the bearing, inclination, and angle the bedding makes with the core axis is known for each of the three holes. Such determination, valid only if the bedding orientation is fairly uniform within the area drilled, is considered simpler, faster, and more effective than any solution previously published. Method: The steps of this procedure are as follows: 1) Mark north and south poles on tracing paper placed over stereonet.* 2) Plot the three diamond drillholes by drawing a line from the center of the net in the direction of the bearings of the holes. Then rotate the paper until each line, in turn, lies along the equatorial diameter of the net; the end of each line is determined by the inclination of the hole measured in degrees from the periphery toward the center of the net along the equatorial diameter. Fig. 1 illustrates a vertical hole and a hole inclined at —23" due east. 3) With the projection of one diamond drillhole along the equatorial diameter, measure from the end of the hole, to the east and then to the west, a dis- tance in degrees equal to the core axis-bedding plane angle. Find two more points by measuring the same number of degrees north then south along the great circle from the end of the drillhole. Draw a circle, the center somewhere along the direction of the projection of the drillhole, to connect these four points. Draw circles for the other two diamond drillholes in the same manner. See Fig. 1 for two circles representing core axis-bedding plane angles of 35" and 23" and Fig. 2 for these plus a third circle representing a core axis-bedding angle of 42" in a hole bearing S 50 W inclined at —52". 4) Rotate the tracing paper until one great circle on the stereonet is found which is tangent to all three of the circles or parts of circles derived in the previous step. Trace this great circle on the paper and join its ends with a straight line passing through the center of the net. The bearing of this line is the strike of the bedding. In Fig. 2 the bedding strikes N 77 E. 5) Rotate the paper until the strike is along the polar diameter of the net. The dip of the bedding is determined by measuring along the equatorial diameter the distance in degrees from the periphery of the net to the great circle derived in step 4. The dip of plane illustrated in Fig. 2 is 55" to the N 13 W. Fig. 3 indicates the solution for three holes whose bearings and inclinations are N 20 W and —43o, due E and —30°, S 30 W and 23" with core axis-bedding angles of 30°, 50°, and 43" respectively. The bedding (stippled area) strikes N 44 W and dips 70" to the southwest.

Jan 1, 1956

By R. P. Carreker, J. C. Fisher

Cheep tests are normally constant load tests. Such tests approximate some types of service conditions and therefore are justified from the engineering point of view. Coupled with this consideration is the advantage of simplicity inherent in constant load tests, as contrasted with the comparatively complex requirements of a constant stress test. It is not surprising that the vast majority of creep tests reported are of the constant load type. Despite the enormous amount of accumulated creep test data, plastic flow is by no means completely understood. The widespread use of constant load tests is at least partly responsible for this lack of understanding. Any attempt to analyze deformation must involve the more fundamental quantity stress, rather than load. It is possible to predict constant load behavior from known constant stress data, but the reverse is much more difficult. When a metal specimen elongates, as in a creep test, the cross section decreases, maintaining constant volume. Thus For a constant stress test the force on the specimen must be decreased as the cross section decreases, that is, this force must be inversely proportional to the elongation of the specimen. An-drade has described three methods of obtaining the constant stress condition,l-3 each of which is relatively complex. The most recent proposal,³ suggests a major simplification which maintains the simplicity of the constant load test while approximating quite closely the desirable condition of constant stress. Andrade's device is admittedly more accurate but the method described below has definite advantages Consider a specimen in the form of a "V" supported at its ends. If a weight be applied at the vertex of the angle, the stress in each leg of the "V" If this stress causes an elongation ?1 in each leg of the "V," the angle decreases from a. to a smaller angle a1. The quantity sec — thus decreases with specimen elongation while the quantity 1/A increases. By selecting proper initial conditions it should be possible to hold S/So very nearly constant at unity. The proper initial conditions are realized when a0 is made equal to approximately 90°. Fig 1 compares the ratios of S/S0 for a0 = 85, 90, 95, 100°, with a0 = 0, that is, a straight speci- men, for true strains up to e = 0.10. It may prove convenient to measure X, the movement of the vertex, rather than the true elongation 1. Contour lines of X/lo are also plotted in Fig 1. The method for obtaining constant stress described above is especially suited to the testing of small wires, but may easily be extended to rods of any diameter through the use of a suitable grip which serves as the vertex joining two identical rods forming the legs of the "V." References 1. E. N. da C. Andrade: On the Viscous Flow in Metals, and Allied Phenomena. Proc. Roy. Soc., A, 84, 1, (1910-11). 2. E. N. da C. Andrade and B. Chalmers: The Resistivity of Polycrystalline Wires in Relation to Plastic Deformation, and the Mechanism of Plastic Flow. Proc. Roy. Soc., A, 138, 348, (1932). 3. E. N. da C. Andrade: A New Device for Maintaining Constant Stress in a Rod Undergoing Plastic Extension. Proc. Phys. Soc., 60, (3). 304, (March, 1948).

Jan 1, 1950

INTRODUCTION Trade financing is a particularly important component of short-term financing for a minerals company since errors, extra costs, or payment delays/defaults can easily wipe out the profit margin on a particular shipment or can cause problems when arranging purchases of e.g. reagents. It is required to make any minerals operation function and does not have to be cross-border to require proper management. Sources of working capital are as follows: 1. Extended credit terms from suppliers 2. Inventory loans from banks, finance companies 3. Accounts receivable financing or factoring 4. Credit lines or overdraft facilities from banks. TRADE CREDITS These are provided under the familiar terms "net 10 days" or payment due by the "10th day of the following month." Thirty days for payment is usual but longer periods can be negotiated with regular suppliers. Shipment may be made on open account with specified periods for settlement. In the mining industry, a custom smelter gains trade credit by paying for concentrates three months after the month of shipment. INVENTORY LOANS Various forms of inventory finance are provided via "floor-plan" or warehouse financing. A set percentage, usually 60%-80%, of a good-quality, readily saleable inventory item (e.g. bullion, concentrates, ingots) will be provided by a bank or finance company which will usually have security over these products and has a right to inspect the goods from time to time. Legal security will he achieved by warehouse receipts, floating liens, chattel mortgages, trust receipts, or through collateral management service companies. The latter certify control over stock or distribution outlets and often carry insurance against fraud. Costs range around 1.5% - 2.0% p.a. or more plus some fees to cover out-of-pockets or other costs. ACCOUNTS RECEIVABLES Accounts receivable financing is based on the company's generation of satisfactory receivables which are continuously assigned to a bank or finance company ("factoring"). Because of the risks in being able to collect receivables, such as payments to a smelter for its blister copper shipments to a refinery, this form of financing costs as much as 3% - 5% of the debt amount purchased plus an additional charge for processing paperwork. Receivables can be purchased with or without recourse and on a notification or non-notification basis to the client's customer to, respectively, pay the invoice directly to the bank or not. LETTERS OF CREDIT Letters of Credit ("L/C's") are a common feature of international trade finance whereby a bank, at the request of the buyer, issues a written undertaking to an exporter to pay a specified sum of money within a set time on presentation of previously specified documents. This undertaking means that the exporter is no longer relying on the credit standing and integrity of the foreign importer. A dispute about shipment does not otherwise affect the obligation to pay upon presentation of a "clean" set of documents. These documents include the hill of lading and other documentation, often on standard "form" bases. There are a number of conventions and techniques in L/C's such as irrevocable/revocable L/C's, time L/C's, confirmation/advising L/C's and transferable L/C's. These are tools to adjust for the varying risks that the importer will not pay. Other routes where one is comfortable with an importer include documentary sight hills (D/P hill), documentary term bills (D/A bill), and, of course, open account.

Jan 1, 1985

The engineering personnel shortage, present and impending, so well brought out in the article in Mining Engineering in the August, 1951 number, both in the editorial lead and the article by William B. Plank and Henry J. Petrie, has left untapped and has ignored a potential source of supply that would fill the need ably and with complete satisfaction. This source is comprised of the women engineers- and geologists, both presently, trained and able to handle work at all levels, and the many who would make splendid engineers and geologists if they could hope for even a modest taste of the square deal that should be theirs, but, as we all know, is not. I write from experience. It is not pleasant or sensible to have to urge borderline cases among men students to consider engineering and geology as careers to fill the need, when I have far more able, interested and suited young women students whom I must divert into other channels. It does not make sense to scrape the bottom and sides of the barrel to induce potentially second or third rate male engineers and geologists to enter the profession when we have superior material among the women, eager to do good work in these fields. It does not make sense for these men to become second or third rate in these fields when they might be first rate salesmen, musicians, advertising copywriters or policemen. Nor does it make any more sense to force potentially first rate female geologists and engineers to become second or third rate and very frustrated typists, kindergarten teachers, dress sales-women or clerks. At this point I am willing to admit that where superstitious -miners object to women in underground workings, men are available for the jobs. Moreover, it is not necessary for women to be sent into the most difficult country, if there is reluctance on either side of the contract. There may be fewer of them eager for the roughest assignments, in proportion to the men, but women are so accustomed to discrimination far more complete than that against any racial or religious group, that a reasonably tough assignment would seem like a heaven-descended joy. In my own experience, I have found that my girl students majoring in geology, could keep up with me in the field in the roughest terrain, but. the men, all but the best students and the most physically fit young men, complained that they could not keep up with me and that I always "walked their-legs off. The women, a few men and I always returned with bags heavy with well chosen specimens and proper notes. Most of the men carried no specimens and-but poor scraps of notes on loose bits of paper. Yet the men were urged to prepare for a career in engineering or geology if their examination marks were reasonably good. When we find that we still have a shortage of engineers and geologists, after putting all the qualified women to work, then we may begin to worry. Until then, we are simply fooling ourselves as we wander in, a forest of outmoded tradition and emotional habit reactions. MARY W. GARRETSON ASSOC. MEMBER, AIME SCARSDALE, N. Y.

Jan 1, 1952

By C. A. Hartinagel

During 1941, the total production of crude oil in New York state was 5,185,000 bbl. This represents a small increase over the average for the past five years. From 1921, when the annual production of the state amounted to only 988,000 bbl., there was a regular annual increase in production (excepting one or two years) until the 5,000,000-bbl. mark was reached in 1937, After more than 20 years of oil recovery by flooding methods, it was generally believed, until a few months ago, that the rate of production was nearly at its peak and within a few years the fields would experience a gradual decline as the thicker sands became exhausted and the thinner ones could be worked only at increasing costs. As a result of the present emergency, however, unusual efforts are being made, in spite of higher costs of operation, to increase the output of Pennsylvania grade oil, to which the New York product belongs. Since most of any increased production would be obtained by flooding, and since floods travel slowly, no large increase in production can be expected for some months to come. During the first year, 10 or 15 per cent increase could be obtained, but maximum production, an increase of perhaps 40 per cent, could not be expected until some time during the second or third year. In the Allegany fields, which account for two thirds of the state's oil production, 1246 wells, including water-intake wells, were drilled during the year; 390 more than in the preceding year and 590 more than in 1939. It is evident that much of the best oil territory has already been developed. As producers move toward edge properties and thinner sands, returns will be smaller, whereas costs remain the same or, under war conditions, become higher. It is estimated that at least 60 million barrels of oil is in sight and will be produced from the thicker sands by present recovery methods. In the thinner sands and edge properties, some 35 million additional barrels can be produced at a profit only if prices become higher. In view of the fact that there is little hope of finding new oil pools in New York, one of the future problems of the oil producer will be to obtain adequate returns for increased production costs. The year started with a posted price of $2.15 per barrel of crude. There were five successive price increases until the high of the year was reached at $2.98 on Aug. 14. Eight days later the Office of Price Administration directed that the price be reduced to the June level of $2.75 a barrel, which remained in effect to the end of the year. With rising costs of operation, it is feared that many of the smaller properties cannot continue production unless the Federal price cut is revoked. During the year, Allegany Refiners Inc., a local enterprise founded in 1933, with plant at Bolivar, western Allegany County, increased its refining capacity from 1000 to 1500 bbl. daily. At the same time equipment was added to make the plant a complete lubricating-oil refinery, including facilities for the refining of wax into the finished product. Previous to the enlargement, it was necessary to sell the wax

Jan 1, 1942

By C. L. T. Edwards

In the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on Ioo per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer's further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blastfurnace charge as good iron as that made without scrap—made with straight ore?" This question may he answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on Ioo per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. Operation with ioo PeR Cent Steel Scrap During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a Ioo per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when Ioo per cent steel turnings were charged. Except for occasional charges of nickel scale as an "cxtra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore—ore and scrap—operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from Ioo per cent scrap to the regular burden, the charge I hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap ' charge. The furnace employed had a hearth 16 ft. o in., bosh 22 ft. o in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter in., bosh angle 73' 27' and a Balrer-Neuman top, with gas-engine blowers. Analyses Range of material charged Gravel: SiO2, 64.40 to 70.54 per cent; A1203, 3.52 to 4.58; CaO, 7.27 to 9.49; MgO, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83. I

Jan 1, 1942

By S. F. Ravitz, S. R. Zimmerley

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By H. H. Rachford, W. P. Schultz

The use of computing machines to solve physical problems has made it imperative to represent physical data in a form computing machines can use. Although curve-fitting is an old and well-practiced art, there still seems to be some interest in questions regarding what methods can be used and why. Even though there are many good references on this subject, it may be of some value to discuss a particular method which has been found to be useful, and to make available the associated tables for its use in the hope that there can be saved a few of the tedious hours necessary to reduce many of the suggested methods to practice. Although a very brief discussion of the mathematical background of the tables is included immediately below, those interested only in their use can skip directly to the section on Use of the Tables. Direct Fit of a Set of Points A frequently encountered problem is: Given data which can be represented by a smooth curve +(x), to find an easy-to-evaluate function F(x), with only a few coefficients, which is a good approximation of +(x) on the interval 0 5 x 5 x,,. Consider F(x) as a linear combination of m + 1 arbitrary, single-valued, continuous, linearly independent functions, f,(x), Ff.r) = a,f,,(x) + a,f,(x) + . . . -+ aifi(x) + If the value of Q(x) is known or can be read from the curve at the points xj: +(x,), +(x,), . . . +(xj) . . . +(x.), and if n = m, then all the coefficients of F(x) can be determined, and F(x,) — +(x,) = 0 for j =. 0, 1, . . . n. This follows from the solution of the set of linear simultaneous equations. +(x<.) = aofu(x,) + aJI(x0) + . . . + a,,f,,(x,) =a, = f,,(x,) + a,f,(x,) + . . . + a,f,,(x,) +(x,,) = a,,f,(x,,) + a,f,(x,) + ... + a,,f.,(x,,) ...........(2) for the coefficients ai. Although the set a, from the solutions of the set of Equations 2 yields an fix) which gives an exact value of $(x,) for the n + 1 points, there is no restraint on ~(xj in the interval xi < x < xj+,. Indeed, if the points +(x,) are not sufficiently smooth, very serious differences may arise between F(x) in the interval and the smooth curve +(x). Least-Squares Fit It has been suggested&apos; that if n is made to exceed m, and the set a, is found to minimize the function the function F(x) is much less sensitive to small errors in +(xi), and usually provides a much better fit to the smooth function +(x). This is known as the best fit in the sense of the least-squares error. To minimize $, set £ = 0,i = 0,1,... iTi,.....(3) The m + 1 equations from Equation 3 are k—n k=n a.^p /,,(a) f,(xt) + a, X A: = 0 k=O k = n k = n k=0 k=0 +(x.) f,(x,),............(4) one equation being obtained for each i = 0, 1, . . . m. Inasmuch as the arbitrary functions f(x) may be evaluated for x,, k = 0, 1, . . . n, and the +(x,) are known values of the curve to be fitted, the simultaneous Equations 4 may be solved for the set a,. Particular Functions Given the functions fi(x) and the set +(xj), the solutions for require evaluating a number of sums of products as well as the solution of an m + 1 order set

Jan 1, 1956

By J. Szekely, R. G. Carr

A method is presented which allows the extension of the Ergun equation for the description of gas flow through packed beds in a nonisothermal regime. The pressure profile in the packed bed is calculated by the establishment of a differential energy balance and the iterative integration of the integral equation thus obtained. The predicted values of the pressure distribution were found to be in excellent agreement with those measured experimentally, under carefully controlled conditions. MANY metallurgical processes are carried out in systems in which a gas stream and particular solids are contacted in a packed bed arrangement under strongly nonisothermal conditions. Ore sintering, the firing of pellets, the operation of regenerators, blast furnace technology may be quoted as examples. Although many aspects of these systems have been extensively studied, an important variable, the pressure distribution and the relationship between pressure head and flow rate, received only little attention to date. The purpose of the paper is to present a brief survey of relevant previous work, followed by a more rigorously formulated model, together with experimental results that afford ready comparison of theoretical prediction with measurement. PREVIOUS WORK A great deal of information is available in the chemical engineering literature on flow phenomena in porous media.&apos; The experimental results pertaining to gas flow were generally interpreted in terms of models based on the analogy with the flow through a pipe of an incompressible, isothermal fluid. Of the numerous, semiempirical correlations that have been proposed to relate pressure drop to the volumetric flow rate, the Ergun equation2 is generally regarded as the most satisfactory: The strong nonisothermality of the metallurgical systems previously mentioned would render the direct applicability of Eq. [I] rather doubtful as both density and viscosity are temperature-dependent. Ergun has used Eq. [I] for estimating the pressure drop in the stack region in the blast furnace by neglecting the viscous term and evaluating the gas density at the integral mean temperature.3 His calculations showed a rather variable agreement with measurements and it was uncertain whether the discrepancy found was attributable to the model or to the inaccuracies often inherent in measurements on an industrial scale. Other work on nonisothermal systems includes studies of the pressure distribution in sinter beds, notably by Voice et a1.4 and Mitchell.5 Mitchell developed a method involving the subdivision of the bed into several zones and assigning average property values (temperature, gas density, and so forth) to each zone. The pressure drop was then calculated for each zone by using an expression analogous to Eq. [I]. This method was an improvement over that described by Voice et al., but even here prediction and measurement differed by as much as 30 pct in certain cases. It would appear that no really satisfactory methods are available for the prediction of pressure drop in packed beds with a strongly nonisothermal regime. The method involving subdivision of the bed into small enough sections, that may be regarded as isothermal, would show promise; however its validity has to be tested by both a rigorous formulation and comparison with experimental data obtained under controlled conditions. In the following a formulation is presented together with experimental data allowing ready practical evaluation of the theory. FORMULATION The mechanical energy balance over an infinitesimal section of a packed bed may be written as follows:

Jan 1, 1969

By S. C. Sircar, D. R. Wiles

The rate has been studied of the hydrogen reduction of nickel ions in acetate -buffered solutions, using a nickel catalyst. At temperatures between 130°and 160°C, the rate is found to be proportional to the catalyst area, the nickel ion concentration, and the hydrogen pressure. The effect of hydrogen ions is to reduce the observed rate, likely by causing the reverse reaction (dissolution) to proceed. The experimental activation energy was found to be 25 kcal per mole. THE precipitation of metals and lower oxides from solution by hydrogen reduction has been quite actively investigated during the past few years.1 In the case of nickel, the kinetics of the precipitation have been studied in ammonia solution2 but extension of this study to acid solutions has not attracted much interest, largely because of the unfavorable thermodynamics at all but the lowest acidities. For example, Schaufelberger foundg that only 10 pct reduction of nickel could be effected in sulphate solutions. One kinetic study of the reduction of Ni++ has been reported by Knacke, Pawlek, and Sussmuth,4 in which the order of the reaction was found to be one in nickel ion and one-half in hydrogen pressure. No mention was made as to the part played by the nickel catalyst, or by the pH of the solution. Moreover, the activation energy reported (4 .12 kcal per mole) is so low as to lead to some question as to whether diffusion might be playing a major role in determining the kinetics. We have recently completed a study5 of the kinetics of the hydrogen precipitation of nickel from acetate-buffered acidic solutions whose results confirm and amplify those of Knacke et al. EXPERIMENTAL PROCEDURES The work was done in a high-pressure autoclavee by the usual technique of removing small samples of the solution for analysis. Nickel analysis was done colorimetrically by the dimethylglyoxime method.&apos; The catalyst used was carbonyl nickel powder (Standard A powder of the Mond Nickel Co., Ltd.) which was found to be composed of spheres of less than 350 mesh. The surface area of the powder was determined in this laboratory by the B. E. T. method to be 1.85 sq m (m2) per g. The catalyst was added to the solution only after the proper temperature and pressure had been reached. Agitation of the baffled system was by a turbine-type impeller, rotated at speeds between 400 and 750 rpm. The reduction rate was found to be independent of the stirring rate, so it was assumed that diffusion in the liquid does not limit the rate. In typical experiments, the nickel concentration was unchanged during an induction period of variable length. The concentration then decreased sharply, and gradually levelled off to approach the final equilibrium value. In some cases, notably at high stirring rates, the nickel concentration was found to increase considerably during the induction period, and then to decrease. In all cases, the rate was determined from the slope of the tangent to the rate curve as the concentration first decreased below the initial value. This is seen in Fig. 1. The rate measurements were found to be reproducible to within about 5 and to be quite independent of the nature or duration of the induction period. The range of conditions used is given in Table I.

Jan 1, 1961

By W. L. Worrell

R. C. Gifkins (CSIRO)—In this paper evidence is put forward to support the idea of grain boundary shearing in aluminum at 4.2°K and the phenomenon is explained in terms of a low-temperature "equicohesive temperature". It is stated that these findings show that grain boundary shear cannot be ruled out in any situation by temperature arguments alone. We believe, from our own recent study of "apparent grain boundary sliding&apos;&apos; at temperatures below 0.45 Tm, that it can be ruled out on temperature arguments alone.45 Our experiments were made principally with magnesium and a Ms-A1 alloy ("Magnox A12"). Careful examination of offsets of marker lines or steps at grain boundaries produced by deformation at room temperature (-0.3 Tm) showed many of these to result from curvature over narrow zones along the grain boundaries. A significant residuum did, however, appear as a sharp offset or step. It was found that the mean value of this step rose to a small value during the first 0.5 to 1 pct strain and then remained at this level with further strain. Moreover, exactly the same values were obtained (at the same stress) at 75°C instead of 21°C. That is, in this range of temperature the "apparent sliding" was not temperature-sensitive. At 125°C and above there was sliding which increased with strain and which was temperature-dependent. When this temperature-dependent sliding was used to calculate the sliding to be expected at room temperature, this underestimated the "apparent sliding" by a factor of 104. The conclusion drawn is that the "apparent sliding" consists of shear localized in a zone of a width measured perhaps in microns, whereas it seems that true sliding occurs on the boundary surface.46 A model for such localized shear has been developed in general terms, following a similar model of Urie and Wain.47 Other strong evidence for low-temper- ature sliding has been based on the offsets of marker lines consisting of a substructure seen using the electron microscope to resolve these.48 We have repeated this work and found that the effects can be accounted for in terms of cracks in an oxide film which is produced when the substructure is etched up; these cracks form over zones of shear rather than at actual interfaces. However, in aluminum at room temperature (-0.3 Tm) there is no "apparent sliding" which is optically detectable. We suggest that, when the temperature is much lower (and possibly the rate of strain higher, too), as in the experiments of Chin et al., then aluminum behaves like magnesium at room temperature, and a narrow zone of shear develops to accommodate differences in strain across the grain boundary. Such a zone could well give rise to triple-point cracks. It is hoped to investigate these suggestions further. B. Y. Chin, W. F. Hosford, Jr., and W. A. Backofen (authors&apos; reply)—It is interesting to have Dr. Gif-kin&apos;s comments, although it is somewhat difficult to reply in detail without the reference containing the work that he describes. Apparently though, he does find a low-temperature temperature-independent sliding that would seem to be related to the observations reported here. Perhaps some of the difficulty has semantic origins, growing out of the distinction between (&apos;true sliding" and "apparent sliding".

Jan 1, 1965

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows: The Robert W. Hunt Medal, The Hadfield Prize, The J. E. Johnson Jr., Award, The Lewisohn Platinum Prize to senior members, and the President&apos;s Prize to junior members. ROBERT W. HUNT MEDAL The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to. a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt&apos;s main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five including the Chairman of the Iron and Steel Committee, shall be appointed by the iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the. award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." SIR ROBERT HADFIELD PRIZE Sir Robert Hadfield has offered an Institute prize of $1000 for researches with regard to the different forms of combination of carbon in iron and steel. Until within a few weeks no paper has been submitted which could compete for this prize. If the paper in hand should not meet the requirements, the donor has suggested that the prize be transferred and offered for: (a) the determination of the hardness in metals in connection. with super-hardness, (b) in consideration of questions of fuel economy, (c) in consideration of questions of industrial development and labor. J. E. JOHNSON, JR. AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute&apos;s Iron and Steel Committee, and a frequent contributor of papers to the Institute&apos;s TRANSACTIONS.

Jan 1, 1925

By L. H. Sjodahl, J. B. Conway

of each particle on grain boundary movement is proportional to the area it occupies on the grain boundary and this increases with the square of the particle radius. In contrast to the impression gained by Tiwari the effectiveness of a particle, as a grain boundary obstacle, increases rapidly as the particle size increases. The counterbalancing factor in a dispersion of constant volume (e.g., those considered by Zener) is of course the rapidly diminishing number of particles, a situation which does not exist in thoria dispersed materials where the volume fraction of thoria remains constant. Although it has been assumed that the Zener approach is valid for the sake of the above argument, it is open to the following objections: 1) It assumes that the effect of many small particles along a grain boundary is cumulative and does not take into account the possibility of each small particle being overcome separately. In this case the boundary will not be able to move forward until the largest particle on the boundary has been overcome. This means that the rate controlling factor will be the rate at which a few relatively large particles are overcome with the remaining small particles playing a negligible role. 2) When the dispersion consists of very small particles the interparticle spacing is usually small compared to the grain size and most particles are located away from grain boundaries where they can play no part. The most efficient dispersion, from a purely geometrical viewpoint, is one where the particle spacing is equal to the grain size so that all the particles are on grain boundaries. Tiwari&apos;s second point that voids cannot prevent re-crystallization seems to be unfounded as several workes20-23 have shown that voids alone can retard grain boundary movement and recrystallization. To further convince Tiwari, Fig. 17 shows a void in deformed TD Nichrome holding back a recrystallization interface. Tiwari&apos;s explanation for the effect of voids on recrystallization, i.e., they reduce local strain energy and hence lower the driving force for recrystallization may be valid in itself but is irrelevant to the present case where even complete recrystallization after ONE of the more recently proposed expressions for describing stress-strain behavior is that due to Voce.1,2 This equation is usually written: s =s8 ?(s8?so)e??/?c [l] where s is the true stress, ? is true strain, cC is a constant called the characteristic strain, s8 is the asymptotic stress approached at high strain values, and so is the threshold stress at which the plastic deformation begins. While this expression has not been universally accepted as yet it does contain certain features which are consistent with experimental stress-strain behavior. In a more recent publication Hsu, Davies, and Royles3 employed the concept of generalized strain proposed by seth4 and identified a method for linearizing the stress-strain plot. In this approach the generalized strain was given by: where 7 is the generalized strain, 1 is the instantaneous length, 1, the datum length, and n is a constant called the "coefficient of strain measure". A value of n was said to exist which would yield the linearity: s —s+ S[.-(tf] [3] In recent studies of both these approaches, it has been found that while the Voce equation and the gen-

Jan 1, 1970

By Basil B. Zavoico

The symposium on production for the year 1942 contains no papers on the foreign situation except those on Argentina and Mexico. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts From Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a Rope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone.

Jan 1, 1943

By H. L. B. Gould, Jr. Wenny D. H.

TO date there has been but limited interest in alloys of 80 to 95 pct Co and Fe with or without other additions. In 1932, S. R. Williams&apos; reported practically zero magnetostriction for the 90 pct Co-10 pct Fe alloy. This same composition was used for pole pieces to control the magnetic field in magnetrons operating at high temperatures.&apos; In 1947, a 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn composition was investigated3 for use in ballast lamps because of its high temperature coefficient of resistance. Recently, as part of a survey of ductile and malleable magnetic alloys capable of being processed to thin gages for possible applications in memory devices, the high Co-Fe alloys have been re-examined to determine their fabricating and magnetic characteristics. Alloys from 80 up to 95 pct Co and Fe with and without additions such as vanadium were prepared. In general these all had excellent ductility and malleability. Wire was drawn to thin gages without difficulty and fine hard-drawn wires flattened to 2) The phenomenon may have potential in estimating the carbon content of molybdenum. A given solution-treating temperature and cooling rate could perhaps be calibrated so that the area fraction of surface covered by carbide could be interpreted in terms of carbon concentration. By segregating to the surface, a big "magnification" of the carbon content is obtained, which should make the method cheap, direct, and sensitive and, therefore, perhaps of interest to the molybdenum industry. This work was conducted at Battelle Memorial Institute. Financial support by the Aeronautical Systems Division, United States Air Force, under Contract No. AF 33(657)-7376, is gratefully acknowledged, and the writer is thankful for the experimental assistance of Miss Marjorie Cantin. ribbon without splitting. Similarly, strip was cold-rolled as much as 99.75 pct reduction to a 0.25 mil thickness without intermediate anneals. Samples of round and flat wire and foil, in the severely cold-worked and annealed states, were checked for magnetic characteristics. The alloys exhibited widely divergent magnetic characteristics depending on the processing and heat-treating procedures used in preparing the samples. Direct-current hysteresis loops showing the different magnetic characteristics of 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn alloys are shown in Figs. 1 to 8 inclusive, while Figs. 9 and 10 show the loops for an alloy of 82 pct Co, 11.75 pct Fe, 5.6 pct V, and 0.65 pct Mn. Figs. 1 and 2 show the high remanence and exceedingly square-loop characteristics of the hard-drawn wire and ribbon roll flattened therefrom. With the change in processing from roll flattening to flattening by drawing through flat diamond dies the resultant change in texture is accompanied by the drastic change in the shape of the loop as shown in Fig. 3. This skewed loop on annealing reverts to a more normal loop as shown in Fig. 8. The most unique loops are obtained with flat rolled strip. These are shown in Figs. 4 and 5. In the case of the hard-rolled material, Fig. 4, there is little change in induction until the magnetizing force reaches 50 oe. From 50 to 60 oe there is a sharp increase in induction to over 15,000 gauss, which for all practical purposes is saturation. The induction remains at a constant value while the magnetizing force decreases to 40 oe. At this point the

Jan 1, 1965

By Albert G. Anderson

I&apos;m sure many of you have wondered what the term "Cross Flow Filtration" means. I shall explain it so that you more clearly understand it, and I hope you will be able to make it a useful tool for you in the future. In the simplest form of cross flow filtration contaminated fluid. or feed stream, is fed at a high velocity down the center of a porous tube, clear fluid weeps through the porous wall of the tube while the suspended solids concentrate in and are swept away by the feed stream. (See figure A). The high velocity flow of the feed stream tends to keep the inside of the tube free from a build up of contamination. By utilizing this cross flow approach to filtration, we have been able to concentrate such things as paint pigments, titanium dioxide, iron oxide, precipitated metals such as uranium yellowcake or silver, cadmium, some metal hydroxides, as well as gelatinous particles such as yeast cells. You will recognize that cross flow filtration lends itself to a recirculation loop system due to the necessity of maintaining a high velocity on the inside of the tube. This means that we generally have a storage tank from which we are recirculating, and the solids will concentrate in the storage tank. (See figure B). The storage tank design becomes an integral part of the total system and is very important to the total function of the system. The cross flow filter system requires only low pressure, and will work with centrifugal pumps, diaphram pumps or in some cases no pump at all. As an example, if we wanted to filter a 10 GPM (37.8 liters/min.) stream that contained 1% of submicronic particulate, we would flow the 10 GPM (37.8 liters/min.) into the storage tank and recirculate through the filter at a flow of anywhere from 30 GPM to 100 GPM (113.6 to 378.5 liters/min.) depending upon the filterability of the particles from the liquid. As the contaminated fluid recirculates, the solids will build up in the storage tank and loop until they reach a level, which is dependent upon the design of the tank. Then the settling rate in the tank becomes equal to the amount of the solids being fed to the tank, and as a result you reach an equilibrium in the amount of solids being presented to the inside of the porous tubing. We have in effect created a dynamic settling tank or thickener. A flow of 10 GPM (37.8 liters/min.) of clear filtrate comes off for either recycle or disposal with periodic removal of thick mud from the bottom of the tank. The thick mud can be either processed through a centrifuge, a rotary drum filter. a flat bed pressure type filter, or other means. Often the small volume of filtrate from the mud de-watering stream can be recycled back into the recirculation tank so that any fines in the feedback are again concentrated, thus closing the loop on the continuous process 100% removal system. Cross flow filtration will not do efficient molecular separation. We work primarily with discrete solids but we do separate them totally from the liquid carrier fluid. I know some of you will raise your eyebrows when I say that we remove 100% of the particulate, but in measurement tests, we have measured the filtrate cleanliness with instruments that record as low as .05 ppm and the instruments read zero, so that it is less than .05 ppm.

Jan 1, 1980

By Clarence W. Dunham

BECAUSE of the earthquakes that occur at Chuquicamata, the design of the smelter stacks constituted the most difficult structural problem of the entire sulphide ore project. Slight tremors occur almost daily and shocks of moderate magnitude are not uncommon. Naturally, the operation of the smelter depends upon the safety of these stacks, and their resistance to earthquakes was the critical feature of their design. Adequate data of the magnitudes of past shocks at Chuquicamata were not available. However, considering the information that was obtained from experiences in other parts of Chile, a period of one to two seconds was adopted as a basis for the design. To complicate the problem further, the stacks had to provide for operations under a wide variety of conditions ranging from the possibility of running one reverberatory furnace and two converters initially to perhaps five or six furnaces and eight or ten converters simultaneously in the completed plant. No one could tell for certain just what the ultimate capacity might have to be because the plans permitted a large extension beyond the first installation if this became necessary. Studies of the stacks were made for many conditions. At first it was thought that one stack 600 or 650 ft high should be used initially for both the furnaces and converters, with a second similar stack to be built for the future extension. This height would provide adequate draft in the rarified atmosphere at the plant&apos;s elevation of 10,000 ft. It would also disperse the gases high in the air. Preliminary studies of this large stack showed that such a structure was possible if made of steel but it would be exceedingly costly. Furthermore, the effects of the tendency for the top to whip under the action of earthquakes might be serious, and the design had to be based upon assumptions which might not be trustworthy. Such a tall stack was finally abandoned in favor of a larger number of smaller ones. Initially, one stack will service the first three or four furnaces. Another will handle the gases from four or five converters. The smelter has been located in such a position that the prevailing winds carry the fumes away from the remainder of the plant. A height of 300 ft for the stacks was finally selected. The top diameter is approximately 24 ft 9 in. clear inside of the lining. The converter stack is located upon a hill alongside the smelter. This provides an effective increase in height because its base is approximately 66 ft above the yard level. The base of the reverberatory stack is at the latter elevation. Stacks made of reinforced concrete or of steel were investigated, and so were many shapes for them. As these studies progressed, the lightness of a steel structure, and the ductility of the metal itself, led to the decision to use steel for the main part of the stacks. The fact that serious damage to one of the stacks would cause the plant to shut down, caused special studies to be made of the stress conditions that might exist around the breeching which had to be nearly 15 ft wide and 40 ft or more high where it joined the stack. This height was necessary in order to provide adequate transition from the horizontal flow of the gases to the vertical direction without undue eddies. This opening constituted a serious source of weakness in the structure. If made with sufficiently strong reinforcement around its edges, there would be a hard spot in the structure that might cause trouble because of shaft vibrations.

Jan 1, 1952

By C. L. T. Edwards

IN the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on 100 per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer&apos;s further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blast-furnace charge as good iron as that made without scrap-made with straight ore?" This question may be answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on 100 per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. OPERATION WITH 100 PER CENT STEEL SCRAP During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a 100 per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when l00 per cent steel turnings were charged. Except for occasional charges of nickel scale as an "extra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore-ore and scrap-operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from i00 per cent scrap to the regular burden, the charge hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap charge. The furnace employed had a hearth 16 ft. 0 in., bosh 22 ft. 0 in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter ¾ in., bosh angle 73° 27&apos; and a Baker-Neuman top, with gas-engine blowers. Analyses Range of Material Charged Gravel: Si02, 64.40 to .7o.54 per cent; A1203,3-52 to 4.58; CaO, 7.27 to 9.49; M90, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83.

Jan 1, 1941

By J. S. Kasper, R. M. Waterstrat, B. F. Decker

THE existence of v phase in the Mn-Mo system was discovered in this laboratory several years ago,&apos; but neither the conditions of its formation nor its composition were known, and preliminary attempts to reproduce the phase were unsuccessful. We wish now to specify the information appropriate to phase formation on the basis of experiments performed since that time. The starting materials were in every case electrolytic manganese and high purity molybdenum. Two methods of preparation were employed: l—arc-melting varying combinations of the elements in an inert atmosphere and subsequent heat treating, and 2—sintering compressed mixtures of finely divided powders of the elements. In the latter method, the powders were first passed through 200 mesh screen and then compressed into cylinders of % in. diameter and % in. length, which were sintered at elevated temperatures in an atmosphere of dry hydrogen. For some samples, the sintering temperature was 1200°C (for 1 hr), and these were then heat- treated at lower temperatures for times up to 24 hr. Eventually it was found, for the proper composition, that essentially pure a phase could be produced by sintering at 1125°C for 3 hr. Quenching to room temperature was effected by means of a stream of cold, dry hydrogen in a water-cooled chamber. The arc-melting procedure was found to be unsatisfactory after an investigation of many samples at different compositions and temperatures. Large quantities of manganese were vaporized during melting and none of the products were homogeneous or contained extended regions of pure phase. Nonetheless, these experiments established that no formation occurs in the Mn-Mo system below 1115oC, and indicated, at least roughly, the composition range of interest for further exploration. The more definite results obtained from samples produced by the second method are given in Table I. A portion of sample 2 heated for 16 hr at 1000°C in a Vycor tube transformed to molybdenum plus unidentified phases of complex X-ray pattern. From these few results it appears that the region of phase is quite narrow in composition. It is of interest that the composition is such as to make for difficulties in correlating this structure on an electron atom basis with other a structures of iron, cobalt, and nickel. In that respect Mn-Mo shows the same anomaly as Mn-Cr and Mn-V systems.&apos; A second feature is that in common with the two other known molybdenum (Fe-Mo and Co-Mo), Mn-Mo v exists only at elevated temperatures. The X-ray powder pattern of the pure a phase of Mn-Mo is given in Table 11. It agrees well with the patterns established for other structures, especially with that for Fe-Mo as given by Goldschmidt.An attempt is being made to establish whether an ordering of the respective atoms occurs and such information will be reported in a future publication. Acknowledgment The authors acknowledge gratefully the assistance of Mrs. J. R. Belanger in some portions of this work. References &apos;J. S. Kasper, B. F. Decker, and J. R. Belanger: Journal of Applied Physics (1951) 22, p. 361. 2 A. H. Sully: Journal Inst. Metals (1951) 80, p. 173. H. J. Goldschmidt: Research (1949) 2, p. 343.

Jan 1, 1954