Search Documents

By M. N. Dunlap

This article summarizes the successful incorporation of a flash-flooding stream into the tailing-disposal system at the St. Joseph Lead Company's Federal Division mill, in St. Francois County, Missouri. The mill was built in 1906, by the Federal Lead Co., as its No. 3 mill for the concentration of southeastern Missouri lead ores, and damming Davis Creek was first considered in 1908. Plans were made also in 1925 and in 1937. Dam layouts varied from a reinforced concrete structure to a barrier built of tailings alone. .All were abandoned because of liability that would be incurred by flash-flood rupturing of an incompleted dam. By 1942 mill capacity had reached 12,000 tons daily and increasing tailing-disposal costs again focused attention on the Davis Creek basin. This time the problem of riskless dam building was solved. Moreover, most of the items that appeared in the answer were materials that normally required wasting and the major portion of labor involved performed functions that it mould normally have done, without constructive benefit, elsewhere. The new layout also made possible advantageous changes in mill-water supply pumping; static head being reduced from 514 ft to 9; ft, friction head from 4900 ft to 2860 ft, and pumping can be done now at periods of low power demand. The following facts about the Davis Creek watershed explain the 36-year reluctance to reach these, and other, benefits. Size: 3600 acres. Outline: roughly pear-shaped, 21/2 by 3 miles at the largest dimensions. Topography: mostly hill land with steep valleys. Relief: 760 minimum to 1153 maximum. Maximum rainfall: 3.36 in. per hour. Permanent water: none natural. Now 2200 gpm discharged through 16-in. drill hole from mine pumps underground. Geology: the 17 acres near dam centerline is Bonne Terre dolomite covered with sand and gravel eroded from Pleistocene beds that cap some of the hills. The remainder of the pond basin is on Davis shale. Soil cover: mostly second-growth timber with some abandoned fields; all subject to careless burning, which reduces water-retaining ability. Flood history: flash-flooding that had taken at least one life. Downstream values: two railroad bridges before creek intersection with Flat River. Immediately below confluence, a highway bridge, a low-water crossing, a few business establishments and several blocks of residences. In July 1942 the following segments of an ingenious plan were put into operation. A ditch 270 ft long, 16 ft wide and 51/2 ft deep was excavated to bedrock in the gravelly soil along the proposed dam's centerline. This excavation, which exposed many gravel-filled channels, was run full of slimes drawn from a riser set in the top of an adjacent tailings-disposal

Jan 1, 1949

(The paper by L. H. De Wald-Tech. Pub. No. 429 was presented at the Boston meeting, September, 1931.) W. A. SCHEUCH, Chicago, Ill.-Since starting up our Hawthorne copper wire plant we have found that wire bars from certain suppliers perform quite differently from those of other suppliers. In attempting to evaluate these bars, we made cross-sections, and in making these cross-sections we found considerable variation in the crystal structure. Indications were that there was some preference in the type of crystal structure. In attempting to find the reason for that we discussed it with the various producers and-also reviewed the literature. Mr. DeWald was assigned to determine the various factors that enter into copper wire bar crystal structure, on the basis that the product was a horizontally cast wire bar of practically identical composition and of recognized good composition for the present quality product sold in the market. Mr. DeWald has asked me to say that he should have made reference to Mr. Dalzell's paper on a theory concerning gases in refined copper. D. K. CRAMPTON, Marion, Conn. (written discussion).-Mr. DeWald has set forth an interesting and thorough exposition of the factors controlling macrostructure of this material. It is particularly interesting to us as it somewhat parallels work we have done on macrostructure of round copper billets for piercing into tubes. Our findings as to the effect of the several variables on macrostructure check Mr. DeWald's. The general principles underlying the two are precisely the same. The fact that we worked with copper deoxidized with phosphorous instead of tough-pitch copper, and round billets cast on end instead of wire bars, does not influence the results. We have found that round billets cast so as to produce large radial grains have greater soundness and density than those with a fine macrostructure. Further, and more important, we have found that the billets with large radial grains show markedly different performance on piercing from those having a fine equiaxed structure. With a given temperature of billet and adjustment of piercing machine, the coarse-grained material requires appreciably lower power for piercing and goes through the operation inn appreciably less time. These two differences are of sufficient commercial importance to warrant exercise of great care in maintaining the coarse structure. It seems probable that much the same phenomenon should hold in the hot rolling of tough-pitch wire bars. We would expect that, other things being equal, the coarse-grained wire bars would roll more readily and require less power than fine-grained ones. Moreover, we believe the differences in initial structure of the wire bars should be largely eliminated in the hot rolling process and during the subsequent drawing and annealing, of wire would be entirely eradicated.

Jan 1, 1932

By F. L. Robertson, C. H. Bacon, J. W. Till

A description is given of the development of a process for making low sulphur steel on furnaces fired with 2 1/2 pet sulphur oil. Slag and metal are analyzed at melt. Slag weight is estimated. A simple method for calculating necessary lime additions for making 0.025 and 0.035 pct sulphur steel is given. DURING the last 15 years John Summers & Sons have been confronted increasingly by the problem of producing a low sulphur steel from high sulphur materials. The principles adopted, the processes used, the data collected on a furnace specially set aside to study this problem, and speculation on future developments are dealt with in this paper. This study is limited to two melting shops which make sheet steel only, of the following analysis: C, 0.06 pct; Mn, 0.33; S, 0.04, 0.035, 0.03, and 0.025; and P, 0.02 and 0.015. All the processes described have reference to the manufacturing of this steel and are not necessarily applicable, without modification, to other steels. The raw materials used are given in Table I. Development of Process About 1934, Schenck's work on phosphorus was applied to frame quantitative rules for the removal of phosphorus, with great success. We could however, neither in our own work nor in the voluminous literature, find any assistance to frame quantitative furnace rules to remove sulphur. Perhaps, we should have persevered with Schenck's outstanding chapter on sulphur in The Physical Chemistry of Steelmaking, but we missed the importance of one (Ss) sentence on p. 478. "Evidently this ratio -------- is [S] the important quantity to be considered from the point of view of chemical reaction; it is clear that the sulphur content of the steel alone, as frequently given in the literature cannot suffice for judging the success of the reaction unless special details are given regarding the sulphur charge and the amount of slag."' We were not however very successful in getting values for Schenck's "n" that agreed with (S) arrived at by our direct analysis. [S] In addition to Schenck's work much attention was given to V value. The formula selected for V was: (SCaO) — 1.57 (2 P2O5) (S SiO2) After plotting many charges a curve was obtained, based upon the relationship between the percentage sulphur in the finished steel and V value, Fig. 1. For a long time this was used as standard with about a 60 to 70 pct success on producer-gas fired furnaces, if all uprising scrap was used and no bought scrap used. An inspection of this curve shows clearly that it is not a quantitative manufacturing process, and that it was not sure enough to go to the trouble and expense of doing stage analysis for P,O,,

Jan 1, 1952

This paper "On Coal" was published in three issues of The Western Gleaner in 1814. Name of author is not given. This magazine was started by Cramer, Spear & Eichbaum, in Pittsburgh, Pa., in December 1813, and ran for about two years. Copies are very rare, and this one is made from an original in the Darlington Library, University of Pittsburgh. This is almost certainly the first general article on coal published west of the Allegheny Mountains, and one of the earliest in this country. ON COAL Its Natural History-Mining of Coal-Phenomena occasioned by Fire-damp-Method of Coking-Distillation of Tar from Pit-coal-Gas-light-Coal, a Manure I. NATURAL HISTORY OF COAL There are few productions of nature which present to the philosopher a wider field of investigation than pit-coal. A substance highly inflammable is found in the deep recesses of the earth, sometimes loaded with numerous superincumbent strata of hard rock, and extending frequently along with these strata through a vast expanse of territory. Though metals may be said to be inflammable substances, as they combine more or less rapidly with oxygen when placed under particular circumstances, yet the character of rapid combustion with disengagement of light and heat, seems to belong. principally to such substances as are derived either from the animal or vegetable kingdom. That this is probably the case with regard to coal we are further induced to believe, by the remarkable circumstance, that the chemical analysis of this natural production yields especially, though in various proportions, those materials which constitute essentially the vegetable. And if any thing was wanting to confirm, us in that opinion we might trace in a number of fossile substances the gradual transition of the vegetable into the state of mineral coal. This fact is so intimately connected with the natural history of coal, that we cannot think it superfluous to give it some farther development. Among the great number of principles which the chemist is capable of tracing in the vegetable kingdom, the presence of extract, resin and fibre seem to form the characteristical marks of plants.-If vegetable matter be boiled in water, and the water, after having been strained and filtered, be exposed for some time to the open air, a flocculent precipitate takes `place from every part of the liquor; which soon subsides to the bottom of the vessel containing it. This is the extract; altered, indeed, by exposure, and now no longer soluble in water, a change which is supposed to depend on the absorption of oxygen; and if, by any means the proportion of oxygen be increased, the extract gradually becomes of a darker color, blackens, and approaches to the state of charred wood.

Jan 1, 1942

By Richard P. Schoemaker

Introduction In underground mining operations the effects of economic and mechanical factors on costs and profits can readily be appreciated and can perhaps be expressed in exact figures and percentages. Less apparent, but frequently more important, is the influence of physical stress. Stress causes failure of supports, collapse of openings, rockbursts, and other damage which directly affects the costs of maintenance, and also to a certain extent the accident rate. Stress can, however, if properly directed, be an aid to mining operations. The caving methods in metal mining and the long-wall method in coal mining are well-known examples. In large-scale mining operations it is almost impossible to neglect stress-control. A better understanding of the mechanism of rock pressure and the application of its principles to practical mining will inevitably lead to a reduction in operating costs. Many theories have been advanced to give the mining engineer a practical outline for stress-control but, although today most experts agree upon the principles of stress distribution around underground openings, there is still no generally accepted theory that explains all phenomena. The main reasons for this incomplete understanding of the problem are the lack of accurate knowledge of the physical properties of rocks under field conditions, and the great complexity of these conditions due to in-homogeneity of the rock, stratification, tectonic disturbances, and many other unknown factors. The research on the rock pressure problems has, however, yielded some valuable facts which, expressed in practical terms, and adapted to local conditions, may become a valuable aid for mining operations. The purpose of this paper is to give a review of the most important accomplishments of this research with respect to the stress phenomena around small underground openings, such as tunnels and shafts, so as to arrive at an outline of the problem as it stands today. Special emphasis is placed on a new theory by the German mining engineer, Rudolf Fenner, which has never before been published or discussed in English. The Pressure Dome Theory The formation of a dome-shaped space around underground openings is well known from field observations. When openings are made in rock under stress, the rock in the top of the openings will often fail, and caving will continue until the openings have assumed a dome-shaped form, after which equilibrium apparently is re-established. The oldest theory which attempted to explain the phenomenon is the "beam" theory, which postulates that the hanging wall consists of stratified measures that behave as independent beams with fixed ends and a uniformly distributed load. When failure of the beam occurs, inward shearing at the ends will cause the formation of a dome-shaped space. The pressure dome theory, which more or less evolved from the beam theory, merely

Jan 1, 1949

By J. W. Hickman

INTRODUCTION MOST of the electron diffraction studies of oxide films which form on metals and alloys have been carried out by oxidizing the specimens in an auxiliary furnace, cooling down to room temperature and then inserting the sample in the camera and taking a diffraction photograph. Prior to the investigations at the Westinghouse Research Laboratories, no systematic study of the oxidation of any metal or alloy had been made over a wide temperature range with photographs taken at elevated temperatures except the investigation of iron by Jackson and Quarrell.1 In order to interpret the electron diffraction patterns of the oxides which may form on alloys, it seemed advisable to make a comprehensive study of the oxidation of the purest metals available in the bulk form. Thus far studies have been completed on iron,2 cobalt,2 nickel,2 chromium ,2 Copper2, tungsten,3 molybdenum,3 beryllium ,4 uranium,4 thorium4 titanium5 and zirconium5 while investigations are in progress on tantalum and columbium, The next step in the study is concerned with the investigation of the oxides which form on binary alloys. Some of the alloys consist of a single, phase while others contain more than one phase. The identification of the oxides on the surface of a binary alloy may be more difficult than on the metals since oxides containing both metals as well as those of each metal separately may form. Furthermore, it is possible that solid solutions of the various oxides may occur. In these cases the electron diffraction method may not be able to identify the oxidation products unequivocally, Examples of solid solutions which may present difficulties are MoO2 and W02, Fe3O4 and FeO-Cr2O3 since the diffraction patterns are so similar. Since electron diffraction can determine only the structure of the oxide, the chemical composition must be inferred from the diffraction data based upon X ray diffraction investigations of specimens of known composition. It is possible in some cases to decide whether a given solid phase reaction can occur on the surface of an alloy by a study of available thermodynamic data. Table I lists the equations for the formation of most of the oxides from the elements together with values of log10 KR for the several temperatures. [OF°R = -RT In KR 0 and-~75T = logi°KR] [?F°R] and KR are the free energy and equilibrium constant of the reaction. Calculations may be made using the values given in Table I to determine whether a given solid phase reaction is possible thermodynamically. For example, a solid phase reaction should occur between aluminum and chromium' oxide to form

Jan 1, 1948

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at subcritical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.1 Westgren, Phragmén and Negresco2 identified the following carbides in chromium steels: [Cementite Fe3C (containing up to about 15 per cent Cr) Trigonal carbide Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide Cr4C (or Cr23C3) (containing up to about 25 per cent Fe) Orthorhombic carbide . Cr3C2 (containing only a few per cent Fe)] The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus.4 By means of dilatometric and microscopic studies, sections of the diagram were established. This diagram showed the presence of the special carbide Cr7Ca in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in r per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7Ca occurs in chromium steels containing more than about 1 per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. EXPERIMENTAL PROCEDURE The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into 1-in. round bars, and all heat-treatments were conducted on specimens of this section .size. Sections of the bar stock 8 in. long were hardened in air, oil or water depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after auenchine. The quenched bars were cut into

Jan 1, 1942

By Raymond B. Ladoo

Abrasives include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean or otherwise remove solid material, usually by rubbing action but also by impact (sandblasting, for example). They do not include abrasive tools-for instance, lathe tools and files-or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted although some chemical-action polishes and cleaners may also contain solid abrasives; for example, many automobile and metal polishes. General Considerations The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded grain abrasives such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cutting edges when grains become worn-for example, in garnet for sandpaper, neither highly cleavable or friable grains nor extremely tough grains are wanted. For still other uses, great hardness is objectionable; for example, abrasives for dentifrices and for glass-cleaning soaps. For the most efficient use in the more critical applications, the different types of abrasives are rarely completely interchangeable; thus, while crushed quartz and garnet are both used in sandpaper, the papers are not at all interchangeable in their use applications. In the last analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work done by the abrasive per unit of cost. Initial cost of an artificial abrasive. may be much greater than that of a natural abrasive but the artificial abrasive may do so much better work than the natural one, and do it so much faster, that the ultimate cost will be less. It is on this basis that artificial abrasives have largely replaced natural abrasives for grinding metal. Classification Abrasives may be divided into two general classes, natural and manufactured. The former includes all rocks and minerals used for abrasive purposes without chemical or physical change other than crushing, shaping or bonding into suitable forms. Manufactured or artificial abrasives are made either by heat or chemical action from metals or mineral raw materials. On page 2 is a list of the most important abrasives, classified as to inherent types and as to forms in which they are used industrially. For most types of use there are manufactured products that can be substituted for the natural products, usually at higher initial

Jan 1, 1960

By Benjamin Lustman, Robert F. Mehl

The study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation—i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from 0 to 1000-2000 ?ngstroms—has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difierence may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations.3'4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 Experimental Procedure Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and repro-ducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900° to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal. After this treatment, the specimens were cooled in hydrogen to room temperature and placed in the oxidation furnace, where

Jan 1, 1941

By G. R. Gardner, D. H. Davis

Increasing realization of the importance of dust control, and the recommendations of various agencies, have led the mining industry to become actively concerned with this problem. The background and necessity for adequate dust-suppression measures have been discussed in a number of publications, including those of the U. S. Bureau of Mines, and the use of spray water to reduce dust at the face and on roadways has been recommended. The problem resolves itself into obtaining adequate dust reduction at a reasonable cost. Inasmuch as the term "adequate dust suppression" has never been clearly defined, nor have permissible limits of dustiness (in terms of dust count) been established, it is apparent that any method selected may be required to meet additional demands. Until the industry has been given some indication of permissible limits of dustiness, no permanent solution is possible. Progress will be somewhat handicapped until such information is available. In addition, dust reduction must be obtained without the addition of any excessive moisture to the coal, since consideration must often be given to: I. Quality standards, particularly reduction in heat value. 2. Handling characteristics, particularly in regard to unloading from railroad cars and bins. 3. Application of dry methods of coal cleaning. 4. Necessity for fine screening within specified limits of oversize and undersize. Little detailed information is available as to the advantages and disadvantages of the several methods of water distribution, the location and protection of sprays, operating data on pressure, quantity of water, and so forth, and results obtained. In 1940 an investigation was undertaken to determine and evaluate the principal factors involved. This paper constitutes a progress report on this work and cannot in any way be regarded as complete on any one of the several phases. Classification of Dust Sources The various sources of underground dust may be classified as primary or secondary. A primary source is one associated with appreciable degradation of size, that is, where the greater part of the actual fines capable of becoming air-borne dust are produced. A secondary source may be considered as one in which the greater part of the fines have been produced at some previous operation and are in such condition that they can be dispersed as air-borne dust. These conceptions appear to be of practical significance, as experience indicates that when dust is controlled at the primary sources the importance of secondary sources is minimized. For these reasons, investigations to date have been concerned principally with the primary sources of dust, and this paper is concerned particularly with one of these—namely, undercutting. In accord with the foregoing definitions, the sources to which the following opera-

Jan 1, 1942

By L. C. Aycock, J. Hunter, P. M. Lyons

In view of the unfavorable discovery trend that has set in during the past few years, it seems permissible to infer that the large, more easily found crude reserves in Louisiana are now known. Without doubt, many new producing areas will be located, but in the light of development during the past few years the majority of new areas probably will be found at greater depths and from relatively poorer sands. f Although sufficient reserves exist in Louisiana to last at the present rate of production for a considerable period, additional reserves must be found in more intensive development of the presently known structures. In order to ensure the greatest ultimate recovery from such structures, the most advanced technical methods must be employed in their exploitation. Wherever possible, cycling and repressuring plants should be installed. 'here are presently in Louisiana, especially in south Louisiana, a great many fields that contain gas-condensate reservoirs. These reservoirs cannot be produced for their liquid hydrocarbon content under present conditions without wasting an enormous quantity of gas and creating underground waste. Although some of these reservoirs are being produced, such production must be considered in the nature of a salvage operation rather than as a sound economic proposition. Such reservoirs, however, can become profitable ven- tures through the use of cycling and repressuring plants. Cycling operations now operating in Louisiana have increased the ultimate recovery from gas-condensate reservoirs anywhere from 10 to 30 per cent. Cycling operations will also provide a considerable reserve of gas, without which Louisiana cannot hope to develop any program of industrialization. During the past year, Louisiana attained the rank of third among the oil-producing states of this country. With a proper program of exploitation and development, and with emphasis on conservation, Louisiana can maintain this position for a great many years. Production On Dec. 31, 1943, oil and/or gas were being. produced in 52 parishes, or 81 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 14 produced oil, and 5 produced solely gas. Tensas Parish in north Louisiana and Assumption Parish in south Louisiana formerly contained no producing fields but during 1943 joined the ranks of the producing parishes. Twenty-three new fields, including one rediscovery, were found during 1943-—a rate of discovery almost comparable to that of the preceding year. Eleven of these new discoveries were either gas or gas-condensate fields. Thus, the trend of development in finding new reserves was also comparable to that of 1942. Many reasons of considerable merit have been advanced to account for the discouraging lack of crude-oil reserves found during the past year. None are, however, completely satisfactory.

Jan 1, 1944

By Hubert D. Keiser

An observation that is finding fresh confirmation in the leadership of the Allied Nations is "When the need arises, a man will rise to fill it." Much the same can be said of industrial advances in the current emergency. Events and circumstances have created needs for new materials and stimulated the inventive genius of man to fill them. The timely development of fibrous-glass manufacture, in relation to present war needs, is a case in point. Historical Summary It is probable that the first glass fibers produced by the hand of man were made about 4000 years ago. Successful production of glass fibers for manifold industrial and military uses, on any scale that could begin to meet present needs, has a history spanning a scant four years. The American processes that brought this young industry into being were developed between the years 1931 and 1937; research and manufacturing efforts were consolidated to create a commercially satisfactory operation as late as November 1939. In the 40 months that have elapsed since then, the industry has achieved commercial importance, supplied immense quantities of materials for pre-war industrial expansion to meet "defense" and Lend-Lease needs, and now has reached such importance that it has come largely under the control of the War Production Board for equitable distribution of its major products among 13 claimant agencies. It is worthy of note, however, that the Bureau of Ships, Navy Department, began exploratory use of fibrous-glass products in 1932, within one year after the date of the first experimental trials of the new process. This early recognition of the military importance of fibrous glass gave impetus to further research work. The foregoing rapid scanning of historical development must be filled in, lest the. impression be created that glass fibers were suddenly created out of thin air, with no antecedent trials, failures, and partial successes. The actual history of glassmaking is lost in antiquity. Probably some nomadic tribesman found molten glass beneath the bed of a hot campfire built upon sand of the proper composition. If his curiosity led him to poke the glowing, viscous pool with a green-wood stick or some handy weapon, it is probable that he drew a glass fiber on the end of his implement. Molten glass has much the same consistency as honey or molasses; it strings out tenuously. Thus, it is quite possible that the first form of glass shaped by man's action was a glass fiber. Artisans in glass, throughout the long Direc- of glassmaking as an art> drew fibers from fine rods for many decorative applications, including "spun glass" decoration in beautiful stemware and the charming millefiori (glass flowers encased in solid glass), and even to create the blood vessels in glass eyes to match a bleary mate.

Jan 1, 1948

By F. R. Archibald, C. M. Nicholson

The present paper may be considered complementary to an earlier contribution on the same subject by F. R. Archibald and C. F. Jackson.1 It is particularly concerned with engineering and technological aspects of the operations at the Harleyville Alumina Plant during its period of operation from January 1945 to July 1946. The plant was built for and operated by Ancor Corporation, at Harleyville, South Carolina, as part of the government sponsored wartime program related to alumina production from domestic raw materials. The main purpose of the program was to secure technical and engineering data, based on actual plant experience, that might serve as a foundation for large scale production of alumina from raw materials other than bauxite. The Harleyville plant was directed specifically to treatment of clays found in very extensive deposits in the Carolinas and Georgia using the lime-sinter process developed by Ancor Corporation. It is considered that the purpose stated above has been served and this paper is to record and discuss some of the more important findings. The main factor in location of the plant at Harleyville was the presence in that locality of a rather remarkable deposit of high calcium limestone. The clay mining operation was centered near Aiken, S. C., and although a rail haul of ninety miles was involved there were, at the time, factors favorable to the Harleyville location offsetting, in part, the cost of transportation of clay, There are, no doubt, locations in the general area where clay and limestone deposits may be found in closer proximity hut they had not been proven up when the project was undertaken. Availability of power from the Santee-Copper development whose high tension line skirted the Property; ready access to rail and highway transportation; the promise, realized in actuality, of ample supply of soft water; and availability of labor supply were other factors of importance. Moreover, the general area has the decided advantage, for this type of operation, of a mild climate. Construction was begun in August 1943, and although stopped for a time priding review of the general situation that fall, it was resumed, albeit with less urgency, and substantially completed by the end of 1944. The total capital cost was approximately $3,460,000 The first alumina was turned out in April 1945 and from then until the plant was closed down in July 1946, the operations followed a succession of periods of production alternating with periods in which minor alterations were made in conformity with experience. Steady improvement was made and at the time Operations were discontinued it was considered that experience and the necessary engineering were in shape for removal of the remaining bottlenecks and a somewhat major revision in one section of the plant. Unfortunately this could not be carried out and it was necessary to discontinue the

Jan 1, 1949

By R. Al-Hussainy, H. J. Ramey

Previous gas well test analyses have been based mainly upon linearizations of ideal gas flow results, although a method for drawdown analysis based upon real gas flow results has been proposed. Linearizations based upon ideal gas flow require estimation of gas physical properties at Tome sort of average pressure, and implicitly involve the assumption that pressure gradients are small everywhere in the reservoir. A new real gas flow equation has been developed by means of a substitution which couples presTure, viscosity and gas law deviation factor. This sub-stitution has been called the real gas pseudo-pressure. Use of the real gas pseudo-pressure leads to simple equations describing real gas flow which do not contain pressure-dependent gas properties, and which do not require the assumption of small pressure gradients everywhere in the flow system. Equations required to determine flow capacity, well condition and static formation pressure from pressure drawdown and build-up tests with the real gas pseudo-pressure concept are presented. Also shown are applications of the real gas pseudo-pressure to back-pressure testing, the gas materials balance and rigorous determination of average gas properties for previous gas flow equations. Included are sample calculations for well test analyses. INTRODUCTION A recent study' of the flow of the transient flow of real gases in ideal radial systems showed that it is possible to consider gas physical property dependence upon pressure by means of a substitution called the real gas pseudo-pressure. The substitution has the advantage that it enables engineering solutions for steady and transient flow of real gases that are more accurate and general than those previously available. The solutions are particularly important for the case of gas flow in tight, high-pressure formations under large drawdowns. Even for more ideal flow conditions, the real gas pseudo-pressure concept leads to important rules for finding average gas physical properties pertinent for older well test analyses. Ref. I provides a detailed study of the theory behind the real gas flow correlations to be used in this paper. The purpose of this paper is to provide necessary engineering forms for use of the real gas flow results, and to illustrate applications. The following considers flow of real gases in an ideal radial flow system. It is assumed that: (1) formation thickness, porosity, water saturation, absolute permeability, temperature and gas composition are constant; (2) gas compressibility and density are functions of pressure as described by the gas law pv = znRT; (3) gas viscosrty is a function of pressure; (4) effective permeability to gas may be a function of pressure to account for liquid condensation; (5) condensate is immobile; and (6) the formation has no dip.

Jan 1, 1967

By M. R. Geer, H. F. Yancey

WITH the exception of pneumatic processes and ii few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral- dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficiation process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and else- where, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment for many years, and more recently driers employing centrifugal force have gained in popularity. 1 A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal-a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. OBJECT AND SCOPE OF INVESTIGATION Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it on coal slurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1948

By J. Hunter, P. M. Lyons, L. C. Aycock

In view of the unfavorable discovery trend that has set in during the past few years, it seems permissible to infer that the large, more easily found crude reserves in Louisiana are now known. Without doubt, many new producing areas will be located, but in the light of development during the past few years the majority of new areas probably will be found at greater depths and from relatively poorer sands. f Although sufficient reserves exist in Louisiana to last at the present rate of production for a considerable period, additional reserves must be found in more intensive development of the presently known structures. In order to ensure the greatest ultimate recovery from such structures, the most advanced technical methods must be employed in their exploitation. Wherever possible, cycling and repressuring plants should be installed. 'here are presently in Louisiana, especially in south Louisiana, a great many fields that contain gas-condensate reservoirs. These reservoirs cannot be produced for their liquid hydrocarbon content under present conditions without wasting an enormous quantity of gas and creating underground waste. Although some of these reservoirs are being produced, such production must be considered in the nature of a salvage operation rather than as a sound economic proposition. Such reservoirs, however, can become profitable ven- tures through the use of cycling and repressuring plants. Cycling operations now operating in Louisiana have increased the ultimate recovery from gas-condensate reservoirs anywhere from 10 to 30 per cent. Cycling operations will also provide a considerable reserve of gas, without which Louisiana cannot hope to develop any program of industrialization. During the past year, Louisiana attained the rank of third among the oil-producing states of this country. With a proper program of exploitation and development, and with emphasis on conservation, Louisiana can maintain this position for a great many years. Production On Dec. 31, 1943, oil and/or gas were being. produced in 52 parishes, or 81 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 14 produced oil, and 5 produced solely gas. Tensas Parish in north Louisiana and Assumption Parish in south Louisiana formerly contained no producing fields but during 1943 joined the ranks of the producing parishes. Twenty-three new fields, including one rediscovery, were found during 1943-—a rate of discovery almost comparable to that of the preceding year. Eleven of these new discoveries were either gas or gas-condensate fields. Thus, the trend of development in finding new reserves was also comparable to that of 1942. Many reasons of considerable merit have been advanced to account for the discouraging lack of crude-oil reserves found during the past year. None are, however, completely satisfactory.

Jan 1, 1944

By R. H. Tien

This paper presents an analytical solution of the problem of freezing of a semi-infinite slab with constant surface temperature; in this analysis accoz~nt is taken of the heat evolution during the solid-state transformations in the frozen skin. The regions where transformations occur are treated as plane isothermal heat sources; i.e., the rates of transformations are assumed to be infinite. In the model considered, three plane heat sources are assumed to be present in the frozen solid. The solution yields the temperature distribution in the solid, the rates of movement of the heat sources , and the rate of movement of the solidification front. It is shown that, although the sum of the heats of transformations in the solid is about 20 or 43 pct of the heat of fusion of iron or manganese, respectively, the effect of the heat evolution in solid-state transformations on the rate of solidification is insignzficant. IN several recent mathematical studies of solidification of liquid metals'-3 no account was taken of the heat evolution accompanying the solid-state transformations. In the case of, for example, steel, there are several phase transformations 6 -y, y -a, and the magnetic transformation. Whether or not a significant error is introduced into the mathematical simulation of solidification processes by the omission of the heat effects associated with these phase transformations is not known. The purpose of the present study is to investigate the effect of these phase transformations on the temperature distribution and the rate of solidification based solely on the heat transfer point of view. That is, for the sake of simplicity, freezing of a pure metal with solid-state transformations will be considered. The mathematical model which represents the present problem includes four moving heat sources representing freezing and phase transformations, 6— y — a — ferromagnetic. The thermal properties such as conductivity and specific heat, and so forth, are different from one phase to the other. But they are considered to be uniform over any particular phase. The usual Fourier heat flow law is employed. The concept of conservation of energy is applied at every heat source in order to estimate their rate of movement. The temperature distribution in the solid and the positions where transformations occur are expressed analytically in terms of error function solutions and four coefficients which are determined from four nonlinear algebraic equations. These coefficients can be calculated either by trial and error or by any numerical method. MATHEMATICAL ANALYSIS Fig. 1 is a schematic diagram showing the zones of different phases 1, 2, 3, and 4 in the solidified portion of a semi-infinite pure liquid metal. The heat is subtracted from the system at x = 0 which is maintained

Jan 1, 1968

By Hubert D. Keiser

AN observation that is finding fresh confirmation in the leadership of the Allied Nations is "When the need arises, a man will rise to fill it." Much the same can be said of industrial advances in the current emergency. Events and circumstances have created needs for new materials and stimulated the inventive genius of man to fill them. The timely development of fibrous-glass manufacture, in relation to present war needs, is a case in point. HISTORICAL SUMMARY It is probable that the first glass fibers produced by the hand of man were made about 4000 years ago. Successful production of glass fibers for manifold industrial and military uses, on any scale that could begin to meet present needs, has a history spanning a scant four years. The American processes that brought this young industry into being were developed between the years 1931 and 1937; research and manufacturing efforts were consolidated to create a commercially satisfactory operation as late as November 1939. In the 40 months that have elapsed since then, the industry has achieved commercial importance, supplied immense quantities of materials for pre-war industrial expansion to meet "defense" and Lend-Lease needs, and now has reached such importance that it has come largely under the control of the War Production Board for equitable distribution of its major products among 13 claimant agencies. It is worthy of note, however, that the Bureau of Ships, Navy Department, began exploratory use of fibrous-glass products in 1932, within one year after the date of the first experimental trials of the new process. This early recognition of the military importance of fibrous glass gave impetus to further research work. The foregoing rapid scanning of historical development must be filled in, lest the impression be created that glass fibers were suddenly created out of thin air, with no antecedent trials, failures, and partial successes. The actual history of glassmaking is lost in antiquity. Probably some nomadic tribesman found molten glass beneath the bed of a hot campfire built upon sand of the proper composition. If his curiosity led him to poke the glowing, viscous pool with a green-wood stick or some handy weapon, it is probable that he drew a glass fiber on the end of his implement. Molten glass has much the same consistency as honey or molasses; it strings out tenuously. Thus, it is quite possible that the first form of glass shaped by man's action was a glass fiber. Artisans in glass, throughout the long history of glassmaking as an art, drew fibers from fine rods for many decorative applications, including "spun glass" decoration in beautiful stemware and the charming millefiori (glass flowers encased in solid glass), and even to create the blood vessels in glass eyes to match a bleary mate.

Jan 1, 1943

By Benjamin Lustman, Robert F. Mehl

The study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation—i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from 0 to 1000-2000 ?ngstroms—has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difierence may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations.3'4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 Experimental Procedure Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and repro-ducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900° to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal. After this treatment, the specimens were cooled in hydrogen to room temperature and placed in the oxidation furnace, where

Jan 1, 1941

By James G. Crawford

Correlation Of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the petroleum engineer. The water in each producing zone tends to have diagnostic characteristics by which it can be distinguished from every other water above or below that zone in that immediate vicinity. Representative analyses of oil-field waters from producing oil and gas fields in the Rocky Mountain region are included, and the diagnostic characteristics are discussed briefly. It is concluded that the generally dilute nature of Rocky Mountain oilfield waters is a result of dilution by meteoric waters, and that there is no relationship between presence or absence of commercial oil and the character of water in a structure. Introduction The study of waters associated With oil and gas began more than 50 years ago and has been well recognized by operators, engineers, and geologists for about 30 years. It appears unnecessary at this time to recite the history of oil-field water analysis; suffice to say that it has proved its worth many times to the production engineer suddenly confronted with water problems in producing oil and gas wells. Chemists and geologists have studied the possible origin of these waters and as Yet the subject is unsolved in many important phases. There are both local and regional problems connected with the explanation of concentrations and character- istics peculiar to each field, each subsurface zone and each province. Criteria useful in postulating the Occurrence of oil Or gas in One province completely fail when applied to another, and data carefully prepared and analyzed from one field may be actually misleading when applied to another. Correlation of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the engineer. The concentrations and characteristics of the waters are essential to the engineers and geologists making interpretations of electric logs in this region. The behavior of water under conditions of reservoir temperature and pressure is dependent to a great degree upon its concentration and characteristics, and thus important to the reservoir engineer. With the advent of secondary recovery methods in the Rocky Mountain region the characteristics and treatment of water will become increasingly important. Premises upon which Correlation Is Based A brief review of the geochemical history of oil-field waters will suffice to present the premises upon which correlations of the waters are based. Sedimentary rocks which are now stratified were first sediments in seas, lakes and streams. These sediments were filled interstitially with connate water. With burial the sediments were compressed arid consolidated, integrated and indurated into bed rock and much of the connate water was dispelled. Following the formation of bed rock the strata were sub-

Jan 1, 1949