Search Documents

By Victor Formanek, Paul Chataignon, Maurice Rey

IT is found when floating oxidized lead ores by sulphidization, that the presence of calcium salts in the water, is usually detrimental and lowers the recovery. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. The effect of calcium salts is readily visible. Whereas in their absence cerussite is quickly stained brown and then black by sodium sulphide, in their presence the mineral remains very light in color. A similar effect is produced when barium sulphide is used as a sulphidizing agent instead of sodium sulphide. Magnesium salts have little or no effect and even tend to reduce the detrimental effect of calcium salts. A study of this phenomenon indicates that it is due to the precipitation of calcium or barium carbonate in contact with the mineral simultaneously with the formation of lead sulphide. The chemical reactions can be interpreted as: PbCO3 + Na2S = PbS + Na2CO3 CaSO4 + Na2CO3 = CaCO3 + Na2 SO4 They might also be written: PbCO3 + S = + Ca++ = PbS + CaCO3 The precipitation of calcium carbonate can be followed by the lowering of the pH with which it is accompanied. Magnesium carbonate is more soluble than calcium carbonate and usually does not precipitate under the conditions prevailing. It is interesting to note that calcium salts have no effect on anglesite (lead sulphate) because calcium sulphate is soluble, but barium salts hinder the sulphidization of anglesite because of the precipitation of barium sulphate. Remedies When calcium sulphate is present in large amounts, the softening of the water with soda ash is usually too expensive to be considered, but the precipitation of the objectionable calcium carbonate can be prevented in two different ways. One is the use of sodium hydrosulphide instead of sodium sulphide. This salt gives a lower pH than sodium sulphide and does not bring about the immediate precipitation of the calcium which remains in solution as calcium bicarbonate. The other procedure is to add ammonium salts such as the sulphate or chloride which have the property of increasing markedly the solubility of calcium carbonate. Ammonium salts have other effects such as cutting down conditioning time and accelerating flotation. They should be added to the flotation cells rather than to the ball mills. Table I. Effect of Sodium Hydrosulphide and/or Ammonium Sulphate on the Flotation of Two Oxidized Lead Ores Mibladen Ore4 La Plagne Ored Con- Tall- Con- Tail-centrate ing centrate ing Reagents Pb, Pct Pb, Pct Pb, Pct Pb, Pot Without addition of CaSO, NaS 56.0 0.68 43.4 0.65 NaSH 56.2 0.60 40.4 0.50 Na2S + (NH4)2SO4d 54.6 0.56 NaSH + (NH4)2SO4d 43.0 0.66 With addition of 40 lb/ton CaSO4 Na2S 39.4 3.85 34.0 3.21 NaSH 49.1 0.70 49.6 0.88 Na2S + (NH4)2SO4d 53.9 0.85 NaSH + (NH4)2SO4d 51.0 0.45 41.1 0.78 In table I are given the results of representative tests on two different oxidized ores. They show that the strongly detrimental effects of calcium sulphate can be offset by the two procedures outlined above. Sodium hydrosulphide is now used regularly on a mill scale on certain ores. Tests are being carried out with ammonium salts. It should be noted that malachite is subject to influences similar to cerussite. One final word of caution—when the ore is rich in primary slime, which is flocculated by the calcium salts, it may be indispensable to remove these by washing or precipitation with sodium carbonate instead of keeping them in solution by the above methods. Acknowledgment We wish to thank Socibtk Miniere & Metallurgique de Penarroya and Minerais et Metaux, for permission to publish these results.

Jan 1, 1951

By E. T. Hayes, A. H. Roberson, M. H. Davies

R. F. Dornagala and D. J. McPherson (Armour Research Foundation, Chicago)—I should like to compliment the authors for a workmanlike job in determining the partial phase diagram of a system comprised of two rnetals which are certainly not easy to work with. We are completing work at Armour Research Foundation on an Atomic Energy Commission-sponsored project for the determination of eight zirconium binary diagrams. Work on the Zr-Cr system has been completed and should be published within the next year. For our work, Westinghouse Grade 3 iodide crystal bar served as the zirconium melting stock. Johnson-Matthey, electrolytic chromium, specially treated for oxygen removal, was employed. The overall constitution of the system determined at Armour Research Foundation is in very good agreement with the present work. We found a eutectic at 18 pct Cr and 1280 °C, somewhat lower than the value reported. This temperature was confirmed by thermal analysis, incipient melting studies, and regular isothermal anneals. The eutectoid was located close to 1 pct Cr and 835°C by metallographic analysis of annealed specimens. Maximum solubility of chromium in /S zirconium was 4.5 pct at the eutectic temperature. Chromium solubility in a zirconium was less than 0.28 pct at all temperatures. We found the compound at 53 pct to melt around 1700°C, with an open maximum, but determined its crystal structure to be hexagonal close-packed (MgZn, type). The lattice parameters were in excellent agreement with those determined by Wallbaum in 1942. The diagrams are in substantial agreement, and .part of the differences are undoubtedly due to the use of different zirconium melting stock. M. K. McQuillan (Birmingham, England)—I read this paper with a great deal of interest, as it covered the same field as some work of my own.' There are a number of points in the present paper on which I would like to comment. First, I should say that I, too, used zirconium prepared by magnesium reduction of the tetrachloride and electrolytically prepared chromium, and melted the alloys in a Kroll-type arc furnace. The purity of my alloys should, therefore, be comparable with the purity of those of the present authors, and any differences in our observations would not be expected to be attributable to this cause. The differences between my observations and theirs concern the presence of the eutectic, the temperature of the eutectoid, and the melting point of the compound. I would be very much interested in any further evidence the authors may have for the occurrence of the eutectic at 1380°C. During the course of my work I noted that a number of my alloys containing 60 to 90 pct Zr melted at about 1400 °C, and for a time assumed that a eutectic occurred at this temperature as described in the paper. On further investigation, however, I found that the structures of the as-melted alloys could not be made to fit in with this interpretation of the system. If a eutectic exists in this region of the system it would be expected that the as-melted alloys would show the usual type of cast structure, i.e., dendrites of the compound plus eutectic. This, however, does not occur, as may be seen from Fig. 9. The compound seen there is not dendritic in form, and the remaining material is by no means certainly eutectic. It may be argued that a compound such as ZrCrl would not form dendrites but would tend to crystallize in geometric shapes. In this case, however, I have evidence to the contrary, as on the chromium side of the compound, where a eutectic occurs at about 1545"C, the compound formed from the liquid takes on a conventional dendritic form, and the eutectic is observed in the interdendritic spaces in the usual way. There is no reason to suppose that the compound would behave differently in an alloy lying on the zirconium side of the compound composition if a eutectic existed there too.

Jan 1, 1953

By Joseph E. Worthington

The present-day Northumberland gold mine is one of the deposits generally characterized as a Carlin-type occurrence. It lies at the crest of the Toquima Range in Nye County near the center of Nevada. Gold mineralization occurs in two modes, in argillaceous and in silicified limestones, and is generally very fine-grained or micron gold. The Northumberland district has had a history that is typical of many western gold districts: minor production prior to World War II and intermittent exploration thereafter until a combination of geological insight, improved economics, and the advent of heap leach technology created the Northumberland gold mine. Nye County, Nevada, was sparsely populated and little explored in the early years of the settlement of the west; the Northumberland district was not established until 1866. Initial interest was in silver and the district operated as a very small producer for the next seventy years. The disseminated gold occurrences in silicified limestones were recognized and Northumberland Mining Co. was organized to develop the property in the late 1930s. Northumberland Mining Co. actually conducted drilling operations (over 200 drill holes) and mined from small open pits in the silicified limestones. They ultimately produced almost 936 kg (33,000 oz) gold before being shut down by War Production Board Order L-208 in 1942. After World War II gold mining activities were essentially nil for over a decade due to the poor economics of gold production. The property was, however, a known gold producer and attracted recurrent exploration attention. About 45 holes were drilled under the direction of Peter Joralemon for private interests between 1959 and 1963. Next Kerr McGee drilled about 25 holes during 1963 and 1964. Some- what later, in 1968, Homestake drilled 20 holes. The property was then acquired by Idaho Mining Co. which drilled about 30 more holes between 1972 and 1974. By this time the Northumberland mine was becoming somewhat shopworn with over 300 holes drilled. Interest in gold prospects was increasing substantially in Nevada, how- ever, due to rising gold prices in late 1974, and several companies were interested in continuing exploration at Northumberland. In 1975 Cyprus Mines Corp. was successful in obtaining a joint venture arrangement with Idaho Mining Co. for further exploration and development of the property. The overall Cyprus exploration program was under the direction of James G. Hansen, Vice President Exploration. The geologist recommending acquisition of Northumberland was Peter E. Chapman who reported to Joseph E. Worthington, Manager of U.S. Exploration for Cyprus. The basis for selection of the Northumberland mine as an exploration target for Cyprus by Chapman was essentially prior knowledge of regional and 16cal geology and of the mine. Exploration for the next few years was directed by Chapman under the supervision of Worthington. During 1975 and 1976 rotary and check core drilling were conducted that indicated that a substantial Carlin-type or disseminated, low-grade gold deposit occurred in two separate bodies. Drilling was based on geologic mapping and rock chip geochemical sampling. Both ore zones were reflected at the surface as gold and arsenic anomalies in rock chips. Heap leach tests attempted in 1977 were aborted by a flash flood, but were completed in 1978. Engineering studies occupied the next couple of years until the property achieved production in the fall of 1981. It is now producing by open-pit mining with gold recovery by heap leaching and cyanide extraction at a rated capacity of approximately 2722 t/d (3000 stpd) ore. Metal recovery has been projected (probably conservatively) at 5 10 kg/a (18,000 oz per year) gold and 1.6 Mg/a (59,000 oz per year) silver. Reserves are reported to be adequate for ten to fifteen years of production. REFERENCES Anon., 1981, "Gold in Nevada," Span Magazine, Vol. 21, No. 3, Standard Oil Co., pp. 6-9. Koschman, A.H. and Bergendahl, M.H., 1968, "Principal Gold- producing Districts of the United States, Professional Paper 610, US Geological Survey, p. 193. Kral, V.E., 195 1, "Minerals Resources of Nye County, Nevada, Bulletin, Vol. 45, No. 3, Geology and Mining Series 50, Nevada University.

Jan 1, 1985

By Maurice Rey, Victor Formanek, Paul Chataignon

IT is found when floating oxidized lead ores by sulphidization, that the presence of calcium salts in the water, is usually detrimental and lowers the recovery. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. The effect of calcium salts is readily visible. Whereas in their absence cerussite is quickly stained brown and then black by sodium sulphide, in their presence the mineral remains very light in color. A similar effect is produced when barium sulphide is used as a sulphidizing agent instead of sodium sulphide. Magnesium salts have little or no effect and even tend to reduce the detrimental effect of calcium salts. A study of this phenomenon indicates that it is due to the precipitation of calcium or barium carbonate in contact with the mineral simultaneously with the formation of lead sulphide. The chemical reactions can be interpreted as: PbCO3 + Na2S = PbS + Na2CO3 CaSO4 + Na2CO3 = CaCO3 + Na2 SO4 They might also be written: PbCO3 + S = + Ca++ = PbS + CaCO3 The precipitation of calcium carbonate can be followed by the lowering of the pH with which it is accompanied. Magnesium carbonate is more soluble than calcium carbonate and usually does not precipitate under the conditions prevailing. It is interesting to note that calcium salts have no effect on anglesite (lead sulphate) because calcium sulphate is soluble, but barium salts hinder the sulphidization of anglesite because of the precipitation of barium sulphate. Remedies When calcium sulphate is present in large amounts, the softening of the water with soda ash is usually too expensive to be considered, but the precipitation of the objectionable calcium carbonate can be prevented in two different ways. One is the use of sodium hydrosulphide instead of sodium sulphide. This salt gives a lower pH than sodium sulphide and does not bring about the immediate precipitation of the calcium which remains in solution as calcium bicarbonate. The other procedure is to add ammonium salts such as the sulphate or chloride which have the property of increasing markedly the solubility of calcium carbonate. Ammonium salts have other effects such as cutting down conditioning time and accelerating flotation. They should be added to the flotation cells rather than to the ball mills. Table I. Effect of Sodium Hydrosulphide and/or Ammonium Sulphate on the Flotation of Two Oxidized Lead Ores Mibladen Ore4 La Plagne Ored Con- Tall- Con- Tail-centrate ing centrate ing Reagents Pb, Pct Pb, Pct Pb, Pct Pb, Pot Without addition of CaSO, NaS 56.0 0.68 43.4 0.65 NaSH 56.2 0.60 40.4 0.50 Na2S + (NH4)2SO4d 54.6 0.56 NaSH + (NH4)2SO4d 43.0 0.66 With addition of 40 lb/ton CaSO4 Na2S 39.4 3.85 34.0 3.21 NaSH 49.1 0.70 49.6 0.88 Na2S + (NH4)2SO4d 53.9 0.85 NaSH + (NH4)2SO4d 51.0 0.45 41.1 0.78 In table I are given the results of representative tests on two different oxidized ores. They show that the strongly detrimental effects of calcium sulphate can be offset by the two procedures outlined above. Sodium hydrosulphide is now used regularly on a mill scale on certain ores. Tests are being carried out with ammonium salts. It should be noted that malachite is subject to influences similar to cerussite. One final word of caution—when the ore is rich in primary slime, which is flocculated by the calcium salts, it may be indispensable to remove these by washing or precipitation with sodium carbonate instead of keeping them in solution by the above methods. Acknowledgment We wish to thank Socibtk Miniere & Metallurgique de Penarroya and Minerais et Metaux, for permission to publish these results.

Jan 1, 1951

By C. O. Dale, W. J. Rundle

THE upper Mississippi Valley zinc-lead area was the first major lead-producing section in the United States. The lead ore, found near the surface in crevices, was relatively pure galena that could be smelted directly into lead, at first in log hearth furnaces and later in more efficient blast type furnaces. French Canadian fur traders encouraged the Indians to mine the lead ore and showed them how to smelt it into lead that had a high value for bullets1 Nicholas Perrot found lead ore on the Mississippi River bluffs near the junction of Wisconsin and Illinois and in 1690 established a trading post on the Wisconsin side of the river opposite the present site of Dubuque, Iowa.2 Shortly after 1720 discovery of Mine La Mott in Missouri diverted considerable attention from the Upper Mississippi area. Mining continued on a desultory basis with operations concentrated in the Galena, Illinois-Dubuque, area. In 1740 at least 20 miners were at work in the Fever River area around Galena and are reported to have shipped 2500 70-lb pigs of lead to Kaskaskia in 1741." Julien Dubuque established a mining and smelting operation in 1790 near the city that bears his name and was granted sole right to exploit the mining operations on the lands of the Sauk and the Fox Indians. He is reported to have produced 30,000 70-lb pigs of lead in 1805. Following the death of Dubuque in 1810 the Indians refused to let the white miners enter their lands, and little was done on the Iowa side of the river until the Indians were removed by treaty with the United States government in 1832." Early mining was entirely for lead but as the crevices were followed down, increasing percentages of zinc sulphide and zinc carbonate were encountered and at first discarded. Later a market became available for the zinc ores, and hand jigging devices were made to separate the lead, the zinc, and the rock or waste materials. The first record of zinc production from the area is for 1860. Production of zinc passed that of lead before 1900, reached a peak of 64,000 short tons in 1917, fell off rapidly and continually to about 2000 short tons in 1938, and since 1940 has ranged from 11,000 to 19,000 short tons. Lead has been of considerably less importance since 1900, and at present only about 10 pct as much lead as zinc is produced. Practically all of the zinc ore has come from orebodies that are rather flat and wide with considerable length as compared to width. Most of the early lead came from the crevice type deposit, but present production is from the predominately flat zinc orebodies. The Graham-Snyder orebody, scene of Eagle Picher operations, is practically all zinc with little or no lead being recovered. Marcasite, present in varying amounts, makes production of finished concentrates by gravity separation impractical. Satisfactory lead and zinc concentrates have been produced since flotation was introduced in the area in 1927. An acid recovery plant was operated for about 20 years after World War I, but it has been dismantled, and no recovery of the iron sulphides in the ores of the district is being made at the present time. In June 1950 there were three companies operating mines and mills, Tri-State Zinc Co., Calumet & Hecla Consolidated Copper Co., and Eagle Picher Mining and Smelting Co. The Vinegar Hill Zinc Co. had completed a shaft at a new orebody and had started to develop the mine which will supply the Cuba City mill. The Cuba Mining Co. was holding the Andrews Mine inactive. The Dodgeville Mining Co. was not operating but was exploring for additional reserves. Several small mines were selling ore to the Eagle Picher mill. A general area map is given in Fig. 1. The Eagle Picher Mining and Smelting Co. entered the area in 1946 with an active exploration campaign. Leases on a block basis were secured for the area south from the Wisconsin-Illinois line near

Jan 1, 1953

By J. D. Testerman

A statistical technique to identify and describe naturally occurring zones in a reservoir and to correlate these zones from well to well is described. The technique is particularly useful in describing a reservoir where cross flow between adjacent strata is important in determining reservoir behavior. Although it has been used primarily for permeability zonation, the technique is general and can be used to correlate any reservoir property or related data, such as the information contained in well logs. INTRODUCTION One of the first problems encountered by the reservoir engineer in predicting or interpreting fluid displacement behavior during secondary recovery processes is that of organizing and using the large amount of data available from core analysis. Permeabilities pose particular problems in organization because they usually vary by more than an order of magnitude between different strata. Due to the sheer volume, it is almost always necessary to group data and to use an average value to represent a number of measurements. Perhaps the most common method now used to group permeability data is the capacity-fraction technique, which ranks permeabilities in order of magnitude, regardless of the physical location of the permeabilities within the reservoir. The cumulative per cent capacity is plotted against cumulative per cent thickness. This plot is divided into an arbitrary number of zones, generally of equal thickness. Five zones (or averaged groups of data) usually are obtained, each of which is treated as homogeneous in subsequent calculations. The division so obtained has no physical meaning; strata in the same zone, calculation-wise, are usually not adjacent in the reservoir. Reservoir engineering techniques being developed will handle crossflow that occurs between adjacent communicating reservoir strata because of imbibition and gravity segregation. Since crossflow occurs between physically adjacent layers within the reservoir, a new zonation technique recognizing the actual location of strata within the reservoir is necessary. Similarly, the recognition of natural zones is important for predictions of oil recovery by processes involving diffusion. One such process is miscible displacement, where predictions of lateral diffusion within the reservoir must recognize the actual location of the invaded zones in relation to the rest of the formation. Natural zones must also be adequately recognized to account for heat transfer within the reservoir during thermal exploitation. Because of the complexity of the problem, statistics appear to offer the only practical hope of dividing a reservoir into physically-meaningful natural zones. This paper presents a statistical technique for identifying these natural zones and for ascertaining which ones are likely to be continuous between adjacent wells. The zones defined have minimum variation of permeability internally and a maximum variation between zones. The technique is general and can thus be applied to reservoir properties other than permeability. The method will guide the reservoir engineer in estimating which zones are likely to be continuous between wells. However, a statistical correlation based on permeabilities in two different wells is no guarantee that the zones so defined are, in fact, continuous. Rather, the assumption of continuity must be consistent with geological data concerning the depositional environment, as well as justified on the basis of engineering judgment in combination with statistics, just as judgment is required with conventional zonation methods. CALCULATION PROCEDURE The reservoir zonation technique is a two-step operation. The steps are individually described, and a sample calculation is presented in the Appendix. ZONATION OF INDIVIDUAL WELLS First, the set of permeability data at a single well is zone, into Zones. These zones are selected so that variation is minimized within the zones and maximized between the zones. The equations4,6 used to zone the data are where B = the variance between zones, , = the number of zones, i = the summation index for the number of zones, j = the Sumation index for the number of data within the zone, mi = the number of data in the ith zone, k,. = the mean of the permeability data in the ith zone, k . = the over-all mean of the data in the well, W = the pooled variance within zones, N = the total number of

By C. O. Dale, W. J. Rundle

THE upper Mississippi Valley zinc-lead area was the first major lead-producing section in the United States. The lead ore, found near the surface in crevices, was relatively pure galena that could be smelted directly into lead, at first in log hearth furnaces and later in more efficient blast type furnaces. French Canadian fur traders encouraged the Indians to mine the lead ore and showed them how to smelt it into lead that had a high value for bullets1 Nicholas Perrot found lead ore on the Mississippi River bluffs near the junction of Wisconsin and Illinois and in 1690 established a trading post on the Wisconsin side of the river opposite the present site of Dubuque, Iowa.2 Shortly after 1720 discovery of Mine La Mott in Missouri diverted considerable attention from the Upper Mississippi area. Mining continued on a desultory basis with operations concentrated in the Galena, Illinois-Dubuque, area. In 1740 at least 20 miners were at work in the Fever River area around Galena and are reported to have shipped 2500 70-lb pigs of lead to Kaskaskia in 1741." Julien Dubuque established a mining and smelting operation in 1790 near the city that bears his name and was granted sole right to exploit the mining operations on the lands of the Sauk and the Fox Indians. He is reported to have produced 30,000 70-lb pigs of lead in 1805. Following the death of Dubuque in 1810 the Indians refused to let the white miners enter their lands, and little was done on the Iowa side of the river until the Indians were removed by treaty with the United States government in 1832." Early mining was entirely for lead but as the crevices were followed down, increasing percentages of zinc sulphide and zinc carbonate were encountered and at first discarded. Later a market became available for the zinc ores, and hand jigging devices were made to separate the lead, the zinc, and the rock or waste materials. The first record of zinc production from the area is for 1860. Production of zinc passed that of lead before 1900, reached a peak of 64,000 short tons in 1917, fell off rapidly and continually to about 2000 short tons in 1938, and since 1940 has ranged from 11,000 to 19,000 short tons. Lead has been of considerably less importance since 1900, and at present only about 10 pct as much lead as zinc is produced. Practically all of the zinc ore has come from orebodies that are rather flat and wide with considerable length as compared to width. Most of the early lead came from the crevice type deposit, but present production is from the predominately flat zinc orebodies. The Graham-Snyder orebody, scene of Eagle Picher operations, is practically all zinc with little or no lead being recovered. Marcasite, present in varying amounts, makes production of finished concentrates by gravity separation impractical. Satisfactory lead and zinc concentrates have been produced since flotation was introduced in the area in 1927. An acid recovery plant was operated for about 20 years after World War I, but it has been dismantled, and no recovery of the iron sulphides in the ores of the district is being made at the present time. In June 1950 there were three companies operating mines and mills, Tri-State Zinc Co., Calumet & Hecla Consolidated Copper Co., and Eagle Picher Mining and Smelting Co. The Vinegar Hill Zinc Co. had completed a shaft at a new orebody and had started to develop the mine which will supply the Cuba City mill. The Cuba Mining Co. was holding the Andrews Mine inactive. The Dodgeville Mining Co. was not operating but was exploring for additional reserves. Several small mines were selling ore to the Eagle Picher mill. A general area map is given in Fig. 1. The Eagle Picher Mining and Smelting Co. entered the area in 1946 with an active exploration campaign. Leases on a block basis were secured for the area south from the Wisconsin-Illinois line near

Jan 1, 1953

By C. O. Dale, W. J. Rundle

THE upper Mississippi Valley zinc-lead area was the first major lead producing section in the United States. The lead ore, found near the surface in crevices, was relatively pure galena that could be smelted directly into lead, at first in log hearth furnaces and later in more efficient blast type furnaces. French Canadian fur traders encouraged the Indians to mine the lead ore and showed them how to smelt it into lead that had a high value for bullets.1 Nicholas Perrot found lead ore on the Mississippi River bluffs near the junction of Wisconsin and Illinois and in 1690 established a trading post on the Wisconsin side of the river opposite the present site of Dubuque, Iowa.2 Shortly after 1720 discovery of Mine La Mott in Missouri diverted considerable attention from the Upper Mississippi area. Mining continued on a desultory basis with operations concentrated in the Galena, Illinois-Dubuque, area. In 1740 at least 20 miners were at work in the Fever River area around Galena and are reported to have shipped 2500 70-lb pigs of lead to Kaskaskia in 1741.3 Julien Dubuque established a mining and smelting operation in 1790 near the city that bears his name 'and was granted sole right to exploit the mining operations on the lands of the Sauk and the Fox Indians. He is reported to have produced 30,000 70-lb pigs of lead in 1805. Following the death of Dubuque in 1810 the Indians refused to let the white miners enter their lands, and little was done on the Iowa side of the river until the Indians were removed by treaty with the United States government in 1832.4 Early mining was entirely for lead but as the crevices were followed down, increasing percentages of zinc sulphide and zinc carbonate were encountered and at first discarded. Later a market became available for the zinc ores, and hand jigging devices were made to separate the lead," the zinc, and the rock or waste materials. The first record of zinc production from -the area is for 1860. Production of zinc passed that of lead before 1900, reached a peak of 64,000 short tons' in 1917, fell off rapidly and continually to about 2000 short tons in 1938, and since 1940 has ranged from 11,000 to 19,000 short tons. Lead has been of considerably less importance since 1900, and at present only about 10 pct as much lead as zinc is produced. Practically all of the zinc ore has come from orebodies that are rather flat and wide with, considerable length as compared to width. Most of the early lead came from the crevice type deposit, but present production is from the predominately flat zinc orebodies. The Graham-Snyder orebody, scene of Eagle Picher operations, is practically all zinc with little or no lead being recovered. Marcasite, present in varying amounts, makes production of finished concentrates by gravity separation impractical. Satisfactory lead and zinc concentrates have been produced since flotation was introduced in the area in 1927. An acid recovery plant was operated for about 20 years after World War I, but it has been dismantled, and no recovery of the iron sulphides in the ores of the district is being made at the present time. In June 1950 there were three companies operating mines and mills, Tri-State Zinc Co., Calumet & Hecla Consolidated Copper Co., and Eagle Picher Mining and Smelting Co. The Vinegar Hill Zinc Co. had completed a shaft at a new orebody and had started to develop the mine which will supply the Cuba City mill. The Cuba Mining Co. was holding the Andrews Mine inactive. The Dodgeville Mining Co. was not operating but was exploring for additional reserves. Several small mines were selling ore to the Eagle Picher mill. A general area map is given in Fig. 1. The Eagle Picher Mining and Smelting Co. entered the area in 1946 with an active exploration campaign. Leases on a block basis were secured for the area south from the Wisconsin-Illinois line near

Jan 1, 1952

By L. S. Kolbert, C. H. Baab

Introduction In June 1981, the Electric Power Research Institute (EPRI) issued a report titled "Control Systems in Coal Preparation Plants" to determine the status of instrumentation and automation systems in the coal preparation industry. EPRI concluded that the control systems presently being employed in the US coal preparation plants "are relatively primitive compared with those in other mineral processing industries; and analytical instrumentation is virtually non-existent." With tighter specifications on the quality of steam coal, interest is increasing in more sophisticated control systems. One type of device that is currently assisting the preparation plant operator optimize and control the coal cleaning process is nuclear based instrumentation. Nuclear instrumentation includes methods for measuring weight, level, and density as well as for performing elemental analysis on coal. Major Features and Benefits of Nuclear Measurement and Analysis Systems There are many features and benefits of nuclear instrumentation. The major benefit is that nuclear instrumentation is non-contacting. The measuring heads do not contact the process materials. This enables measurements of corrosive, abrasive, or high temperature materials with no loss of performance, reliability, or useful life. Also, there are no moving parts to wear or be fouled by dust or corrosion. Installation is simple and inexpensive. For instance, density gauges are simply clamped onto existing pipe runs. Weigh scales and level switches usually require nothing more than welding brackets to customers' equipment. Once installed, routine maintenance can be performed without interrupting the process. Thus, nuclear instrumentation is highly reliable and easily installed and maintained. The operating life of the instrumentation is virtually unlimited. Principle of Operation Nuclear belt weigh scales, point level switches and density gauges all operate on the gamma-ray transmission principle. A beam of gamma radiation from a radioisotopic source is projected through the process material either on a belt, in a vessel, or in a pipe. Opposite the source is a radiation detector whose electrical output is proportional to the intensity of the radiation it absorbs. Gamma radiation is part of the same electromagnetic spectrum that encompasses light, infrared, and x-rays. In many respects, gamma radiation behaves much like light. However, it is far more penetrating and can be transmitted through considerable thickness of materials that are opaque to visible light, e.g., several inches of steel. Types of Nuclear Instrumentation in Coal Preparation Plants There are four types of nuclear instrumentation presently being employed in coal preparation plants. They are: •Belt Weigh Scales •Point Level Switches •Density Gauges •Coal Analysis Equipment. Each type of instrumentation has a number of potential applications within the plant. What follows is a discussion of three different types of devices and their applications. Weigh Scales In coal preparation plants, weighing instruments are used for measuring material throughput, totalized weight, and batch weight on conveyor belts and other transport equipment. They are also used on drag chain conveyors, vibrating conveyors, and screw conveyors. Weighing is important for receiving the run-of-mine coal, controlling mass flow, scheduling production, and loading and shipping the washed coal to market. There are two basic types of weighing instruments: gravimetric and nongravimetric devices. Gravimetric devices are units which measure the pull of gravity on the material being weighed. Nongravimetric devices are not dependent on the force of gravity on the sample. Nuclear weigh scales are the most prevalent nongravimetric devices used. The nuclear weigh scale works on the same basic principle as other nuclear gauges. The greater the quantity of material placed in the path of a radiation beam, the more radiation will be absorbed by the material. In weigh scales, Cesium 137 source is generally placed above the moving stream of material so that the radiation is directed through the material. An ion chamber radiation detector is on the opposite side of the material. The radiation passing to the detector generates a signal which is inversely proportional to the weight of the material present. This signal is amplified and integrated with the speed of the process flow yielding the weight. The weight is indicated and can be totalized for throughput, batch control, etc. In conclusion, radiation weighing methods have become well established in the coal preparation industry throughout the world. As mentioned before, this device finds its most

Jan 1, 1985

By W. C. Leslie, R. M. Fisher, K. G. Carroll

A nitride, believed to be Si3N, has been separated from three nitrided silicon steels. Germanium nitride, Ge3N4, has been prepared from pure germanium. Comparison of the diffraction patterns indicates that the two nitrides are isomorphous; on orthorhombic structure is suggested in place of the rhombohedral structure previously reported for Ge3N4. THE possibility that a nitride of silicon may, under appropriate conditions, precipitate in silicon steels or in steels killed with silicon makes it desirable to have some positive means of identifying such a compound. One such means is the X-ray or electron diffraction pattern of the nitride. A review of the meager data in the literature indicates that the nitride most likely to form is Si3N4, a conclusion supported by the results of a study of nitrided silicon steels to be published shortly by L. S. Darken and R. P. Smith, of this Laboratory. Unfortunately, there is available no diffraction pattern for this nitride. Data have been reported, however, for Ge3N4 which, judging from the similarity between germanium and silicon, might be expected to be isomorphous with Si3N4. An effort was made, therefore, to form such a silicon nitride, to determine its composition and diffraction pattern and, if possible, its structure. To this end a series of three silicon steels was nitrided under controlled conditions with the resultant formation of nitride particles which yielded an electron diffraction pattern in situ. The particles were then extracted from the steel and an attempt was made to determine their chemical composition. X-ray and electron diffraction patterns were also obtained from the extracted particles, which indicate that the nitride is isomorphous with Ge3N4, although a complete determination of the structure has not been possible. These results show that a silicon nitride with a well-defined diffraction pattern can form in silicon steels, and they suggest that this nitride is Si3N4. Materials and Procedures The sillicon steels investigated were In the form of thin sheet or strip and had the composition shown in Table I. The 0.58 and 1.21 pct Si steels were nitrided by holding them at 1110°F in an H2-NH3 atmosphere containing 3 pct ammonia for 48 hr. The nitride particle size was increased by subsequent heating at 1500°F for 13 1/2 hr in helium. The resulting microstructure is shown in Fig. 1. The steel containing 3.20 pct Si was nitrided at 1200°F for 16 1/2 hr after which it was held in helium at 1500°F for 4 hr. Its structure as seen under the electron microscope is illustrated by Fig. 2. As would be expected from the higher silicon content and the shorter holding time at 1500 °F, the nitride particles are smaller and more numerous than those in the 1.21 pct Si steel. The ammonia-hydrogen treatment reduced the carbon content of the steels to a very low level, so no interference was encountered from carbon or carbides. In the case of the 3.2 pct Si steel, the carbon was reduced to 0.003 pct before nitriding by heating in dry hydrogen. Attempts to obtain an X-ray diffraction pattern from polished and etched surfaces of the 1.21 and the 3.20 pct Si steels were unsuccessful. However, an electron diffraction pattern was obtained from the surface of the steels. The interplanar spacings obtained from these patterns arc shown in Table 11, col. 5. The nitride particles were then extracted from all three steels by dissolving the ferrite matrix in bromine-methyl acetate, the solution used in the Beeghly method for the extraction of aluminum nitride from steel. X-ray diffraction patterns of these residues, obtained by means of a spectrometer and by a 57 mm Debye-Scherrer powder camera using filtered cobalt or chromium radiation, are given in Table II along with the pattern obtained by

Jan 1, 1953

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid iron alloys containing chromium and nickel has been measured in the temperature range 1550° to 1700°C at nitrogen pressures to 1 ah. The solubility surface has been determined for the iron corner of the liquid metallic ternary to 21 pct Cr and 11 pct Ni. The nitrogen solubility increases markedly with increasing chromium concentration. The effect of nickel and the bilinear effect of chromium and nickel are less pronounced. The solubility data are presented, and interaction coefficients are determined from them. THE solubility of nitrogen has been determined in liquid Fe-Cr-Ni binary and ternary alloys. The work in this laboratory has been directed toward a relatively limited composition range, that is to 20 pct Cr and 10 pct Ni. Humbert and Elliott1 studied the entire ternary; but their investigation was, understandably, limited in this region. The region considered here is of the greatest commercial interest. Knowledge of the solubility in these alloys is important for accurate control of the nitrogen levels in various stainless alloys. Also, the solution behavior is of theoretical interest because of its deviations from ideal dilute solution rules at moderate chromium levels. The nitrogen solubility in the iron binaries has been reviewed extensively by Pehlke and Elliott,2 particularly with respect to the dilute solution interaction parameters. More recently, there has been some interest in accurate descriptions of solute interactions in non-dilute solutions. Most of the investigators have adopted a power series fit to accommodate any non-linearity of the data. The Taylor series expansion is adopted here, using Scimar's notation3 for the interaction coefficients. An alternate method, instead of requiring higher-order expansions, is to restrict the range of the composition variables. A planar solubility surface may be fitted to the data and its range of validity determined. If the axes of this region are displaced from the usual origin—the solvent pure iron—a change in standard state is required for the solution reaction. The standard state for nitrogen in iron is commonly taken as the hypothetical 1 wt pct solution of nitrogen in pure iron. However, for an alloy of appreciable solute concentration, e.g., 13 pct Cr or 18 pct Cr-8 pct Ni, it would be convenient to use that base composition as the solvent and redefine the solution reaction in terms of that particular solvent. A brief derivation follows, defining the free energy of solution in an alloy solvent. Following the treatment by Darken and Gurry,4 for a nitrogen pressure of 1 atm: N (pure component) = N (1 wt pct in solvent) [l] AG=RT ln100/ wt pct N in solvent Taking this reaction for an alloy solvent less the same reaction for a pure iron solvent the relation between nitrogen in pure iron and an alloy is: N (1 wt pct in Fe) = N (1 wt pct in alloy) [2] AG = RT[ln(wt pct N in Fe) - ln(wt pct N in alloy)] Adding ½ N2(g) to each side and subtracting N (1 wt pct in Fe) = ½N2(g), the total free energy for solution of nitrogen in an alloy, referred to nitrogen at infinite dilution, is given by: ½N2 (g) = N (wt pct in alloy) L3] AG°3 = -RT ln(wt pct N in alloy )PN =1 atm Interaction parameters have their usual meaning when ?G°/RT is differentiated with respect to the proper composition coordinate. If desired, the dilute alloy treatment may be utilized with the new reference composition as the solvent. This has. indeed, been done by Small and pehlke5 in their analysis of nitrogen solution in liquid 18-8 alloys. The Sieverts' technique was used for this investigation on an apparatus previously described.6 The materials used in this program were: Ferrovac-E iron, 99.95 pct, Crucible Steel Co.: chromium, 99.95 pct, Union Carbide Metals Co.; nickel, 99.9 pct, International Nickel Co. Recrystallized alumina crucibles were used with no evidence of crucible-melt reaction. RESULTS The locations of the ternary compositions investigated are shown in Fig. 1. The data of Turnock7 and small8 have been alluded to in other papers.5'6 There were no departures from Sieverts' law observed for

Jan 1, 1969

By G. W. Healy, L. F. Sander

was investigated by reacting thin discs of calcium oxide with gas mixtures of CO2, CO, and Son. Its value was 19,300 * 300 cal independent of temperature in this range. No solid solubility of sulfur in calcium oxide was detected within the limits of the experimental method and it is estimated to be below 0.025 pct by weight. The importance of lime in desulfurization is well-established but complete information on the pure phase equilibrium: CaO + 1/2 s2 = CaS + +02 [11 is not yet available. The goal of this work was to evaluate solid solubility of CaS in CaO and to determine the free-energy change associated with Reaction [I] at temperatures of 1400" to 1650°C. The equilibrium constant for Reaction [1] can be written: It is convenient to rewrite Eq. [2] in the form: where A = {Ps /PqJ1'2 has been referred to' as the "sulfurizing power' of a gas mixture. In this work, thin discs of CaO were suspended in a vertical tube furnace and exposed to CO + CO2 + SOz gas mixtures having known values of A. The samples were then analyzed for sulfur. As expected, X-ray diffraction confirmed that CaS was the only sulfur-bearing phase formed at the relatively low oxygen pressures used. EXPERIMENTAL PROCEDURE Reagent-grade CaCO3 was pressed in a 3/8-in.-diam pill die and prefired in air to produce CaO discs weighing between 0.004 and 0.01 g. Several discs were used to provide a suitable weight for chemical analysis while maintaining a large surface area to react with gas mixtures. These were placed in a platinum mesh basket and suspended in the gas stream in the hot zone of a vertical tube furnace. Desired gas mixtures were prepared from cp grade CO and CO2 and anhydrous grade SO2. The method of soap bubble displacement was used to calibrate capillary flow meters. While this gave excellent results with CO and Con, some problems with bubble insta- bility and soap film "drag" arose with the use of SO2 at low flow rates. Hence, frequent sampling and analysis of gas mixtures was carried out to insure proper control of the ingoing SOZ. The furnace used for gas:solid equilibration was a vertical mullite tube externally wound with 60 pct Pt-40 pct Rh wire having a diameter of 0.028 in. An inner tube of $ in. ID served as the reaction chamber having Pyrex ground joints sealed to the mullite to provide gas-tight connections at top and bottom. A Pt-Pt 10 pct Rh thermocouple was inserted into a protection tube adjacent to the sample basket to measure sample temperature during a run. Constant-temperature control to 2C was observed at any desired set point within the range of this investigation. This was accomplished by a control thermocouple imbedded in the furnace windings which served to actuate an electronic controller wired for high-low operation. The sulfur analyses of the solid samples were carried out using a stoichiometric combustion technique based on the method of Fincham and Richardson. Some analyses were done using a modified evolution method3 but these were used primarily to check the results of the combustion method. The results were in good agreement but the combustion technique of-ferred an advantage in economy of time and material. CALCULATION OF GAS EQUILIBRIA Heating a given mixture of CO + CO + SO2 to high temperatures gives rise to a large number of product species. The details of calculating the partial pressures of these products of interaction and dissociation can be found in several references4,5 and need not be repeated here. The thermodynamic data selected for the major species in the gas mixtures are shown in Table I. Equilibrium constants from these reactions were combined with oxygen, carbon, and sulfur balances and a computer program written to facilitate the calculations. Some early difficulties in reproducing experimental results were finally traced to the effect of atmospheric pressure changes. No reference to consideration of this question had been found in the

Jan 1, 1969

By L. D. Jaffe, H. C. Mann, E. L. Reed

It has been generally believed that fracture originates at a point and, if the stress is suficient, propagates across the material from this point. Evidence to the contrary is given in Fig 1. This micrograph shows an area close to the fracture of a steel containing The material had been quenched from 1675°F and tempered at 1150°F as a round about 10 in, in diam, and had a static tensile strength of 132,000 psi and a static yield strength of 105,000 psi. The steel was broken in 3000 cycles of reversed bending at a nominal max. fiber stress of 110,000 psi at a speed of 10,000 rpm. It was in the form of a standard R.R. Moore specimen with 45" V-notch, 0.015 in. radius and 0.220 in. diam at base of notch. The fractured edge in Fig 1 is part of the central portion of the specimen which broke during the final sudden fracture. Attention is directed to the short cracks which appear as dark lines within the specimen. Similar cracks were found in another specimen of the material, broken in 1,798,000 cycles at a nominal stress of 40,000 psi. The cracks were found in several areas close to the path of the final sudden fracture. This final fracture appeared microscopically to be wholly brittle and transcrystalline. Closer to the surface of the specimens, near the path of progressive fracture, which presumably advanced gradually during many cycles, there was microscopic evidence of some local deformation, but no microcracks. Neither were microcracks observed in areas distant from the main fracture path. The following explanation is offered: In the sudden fracture of the specimen, a crack propagates along a crystallo-graphic plane, with little or no plastic deformation of the adjacent material, until it reaches a grain boundary or a particle of carbide or inclusion which stops its advance. (The particle or boundary may be outside the plane of polish and not visible in the micrograph.) A stress concentration occurs about the end of the stopped crack. One or more new cracks are likely to start in the zone of this stress concentration. They may lie in the same grain as the first crack or in an adjacent grain. New cracks may occasionally start in a nearby but not adjacent grain whose orientation with respect to the stress leads to more ready fracture than does that of the grain between. Once started, these cracks propagate along crystallographic planes in their grains and the process repeats. This leads to discontinuous, branching chains of microcracks. As the process continues, microcracks probably tend to link up by fracture of intermediate material under the influence of increasing stress concentration. Occasionally, too, there may be a series of nearby grains of similar orientation so that there is a certain continuity of fracture across them. In either case the effective size of a crack is increased, resulting in greater stress concentration at its ends and a greater likelihood of further increase of size of the continuously-fractured region. When one continuous crack crosses the entire specimen, macroscopic fracture has occurred. The fractured edge of the specimen in Fig 1 represents a series of microcracks which became continuous across the entire specimen. The short, dark-appearing cracks in the figure did not become continuous over a large area. The row of microscopic stress concentrations at their ends may link up with those of the "main crack" outside the plane of polish. The above explanation does not imply that microcracks develop at the same rate in all portions of the specimen. They will develop most rapidly where the macroscopic tensile stress and macroscopic stress concentration are greatest. Viewed on a scale large compared to the grains, the fracture would appear to progress continuously across the specimen. Although Fig 1 shows a specimen broken in a fatigue test, it is believed that the microcracks discussed do not depend on the repetitive nature of the stressing used, since they are in the region where "sudden" fracture occurred, presumably in a single stress cycle. The whole process of microcrack propagation outlined above is thought to have occurred during this single cycle. It is believed that discontinuous crack propagation may be universal in brittle transgranular fracture of crystalline solids. Further experiments are under way.

Jan 1, 1950

By Joseph Lindmayer, Karl M. Busen

If silicon is in contact with silicon oxide, a heterojunction is formed which induces an inversion layer ("channel"). Influences of impurities and structural parameters on the channel are discussed. There seems to be no relation between surface damage in silicon and the channel. Phosphorz~s doping of the silicon oxide has no pronounced effect on the channel. Channels which were well above the range predicted by the heterojunction model were related to the action of H* at the silicon/silicon oxide interface. Channels which were well below tlze range predicted by the heterojunc-tion model were related to a transition region in the oxide adjacent to the interface. In support of the assumed transition region and the H+ are the ex-periments described on the paper. Furthermore, the concept of metastable OH groups in silzca, known from other publications, has been used to explain certain channel characteristics by the formation and the accommodation of hydrogen in the silicon oxide. THE electrical characteristics of a semiconductor device in many cases are influenced by the conditions of its surface. Because these conditions often are changing with temperature, time, ambient, or other parameters, numerous attempts have been undertaken to stabilize them by suitable processes. Several years ago Atallal studied the silicon/silicon dioxide interface and since then increasing attention has been given to the silicon dioxide as a means to stabilize silicon surfaces. This led to the evolution of the planar silicon devices where oxide layers are used to protect places at which the junctions are intersecting the surface. The formation of the oxide layers on silicon can be carried out by a variety of processes: high-temperature thermal oxidation (exposing the silicon surface to oxidizing agents such as 02, HzO, COz), evaporation of SiOz, or anodic oxidation of silicon. Originally the oxides were considered able to "passivate" the silicon surface and it was understood that they 1) protected the surface against any influence from the ambient and 2) stabilized surface conditions which were necessary for proper device performance. It soon was realized that the second quality was not always obtainable: Atalla and Tannenbaum showed that, in the process of forming a layer on doped silicon by thermal oxida- tion, electrically active impurities in the silicon near the interface are redistributed, thus giving rise eventually to the formation of unwanted charge distributions. The degradation of planar junctions during reoxidation of silicon was observed by Barson et a. Surface studies with silicon planar junction structures indicated that the breakdown voltage depended on the kind of procedure which was applied during or after oxidation.*" Yamin and worthinge report on charge storage and dielectric properties of SiOz films at elevated temperatures. Another influential parameter on the silicon surface is discussed by Lindmayer and usen,' namely the appearance of a surface potential on silicon as a consequence of the heterojunction formed by the silicon/silicon oxide interface. In the present paper the influence of impurities and structural parameters in silicon oxide in connection with the heterojunction is a particular object of our investigations. I) EXPERIMENTAL The material used was 10 ohm-cm p-type silicon slices with either damaged surfaces (mechanically lapped or polished) or damage-free surfaces (chemically polished). The majority of the slices were oxidized for 1 hr and 20 min at 1250°C in a steam + oxygen atmosphere generated by passing O2 through HzO at 90°C (wet oxygen). This led to oxide layers of about 9000 A. On some slices oxide layers were grown in pure oxygen (dry oxygen). By a photoresist process a set of 20 by 200 mil windows was then etched out from the oxide layer. The pattern of the windows is shown in Fig. 1. In a subsequent process n-type pockets with surface concentrations between 2 x 10" and 5 x 10" cm"3 were formed by phosphorus diffusion. This allowed ohmic contacts between the silicon surface and tungsten probes which for electrical measurements were placed into two adjoining windows and

Jan 1, 1965

By John C. Shyne, Eric R. Morgan

BORON as a hardenability agent of commercial importance has been the subject of extensive study in recent years. It has been suggested in the past that boron increases hardenability by combining with nitrogen, thus rendering it innocuous.&apos; More recently it has been proposed that boron increases hardenability by reducing the free energy of sites of ferrite and pearlite nucleation.&apos; The segregation of boron to grain boundaries, the primary site of nucleation, would account for the large hardenability effect of minute additions of boron in steel. This grain boundary theory has found general acceptance while the concept of boron as a nitrogen scavenger has been disregarded. However, the interaction of boron and nitrogen in steel is considered to be important to hardenability because boron may be made ineffective by combination with nitrogen.". * The present work was undertaken to examine some of the effects of boron and nitrogen arid their interaction in steel. A base composition of moderate hardenability was chosen. This was a 0.35 pct C steel containing 2.50 pct Ni and 0.30 Mo. This composition was used because it contained no strong carbide, nitride, or Table I. Composition of Steels by Analysis, Wt Pct Steel C Ni Mo 0&apos; B N* Base 0.35 2.50 0.30 0.0012 nil <0.0001 Boron 0.35 2.50 0.32 0.0012 0.0022 <0.0001 Nitrogen 0.33 2.60 0.35 0.0015 nll 0.0052 Boron plus nitrogen 0.35 2.48 0.30 0.0006 0.0020 0.0040 * Obtained by vacuum fusion technique. boride-forming elements. The other alloys examined were modifications of the base composition and contained nitrogen, boron, or nitrogen plus boron. The compositions of the four alloys used are listed in Table I. The alloys were vacuum melted from electrolytic iron, electrolytic nickel, ferromolybdenum, and fer-roboron. When required, nitrogen was added by admitting a partial pressure of nitrogen over the melt after vacuum melting. The alloys were cast into 21h-in. diam ingots and hot rolled to %-in. sq bars. No ingot pattern was discernible on the polished and etched cross sections of the hot-rolled bars. The alloys were normalized at 1650°F, then machined into standard %-in. diam end-quench hardenability test bars. Four different austenitizing treatments were used: 60 rnin at 1550°F, 45 rnin at 1800°F, 30 rnin at 2000°F, and 20 rnin at 2000°F followed immediately by 30 rnin at 1550°F. The 1550" and 2000°F treatments were carried out in duplicate for each of the four steels. In order to prevent surface oxidation the bars were austenitized while buried under charcoal in an atmosphere of argon. After quenching the bars in a conventional end-quench fixture, the hardness surveys were made in the usual fashion on parallel flats ground along opposite sides of each bar. These were ground 0.050 in. deep rather than the conventional 0.015 in., to avoid decarburized or deboronized regions.5 The austenite grain sizes which resulted from each heat treatment were observed metallographically using Vilella&apos;s etch for martensite. The criterion used as a measure of hardenability was the distance from the quenched ends of the bars at which a hardness of RC 35 was observed. This hardness represented the inflection point on the hardness vs distance plot. Fig. 1 shows the hardenability of each steel after the several heat treatments. The duplicate tests demonstrated excellent reproducibility; the distance to Rc 35 was reproduced within 1/16 in. for duplicate test bars. All four alloys had the same grain-coarsening characteristics. Neither boron nor nitrogen had any observable effect on grain size. The grain sizes resulting from the various austenitizing treatments were ASTM 7 at 1550°F, ASTM 4 at 1800°F, and ASTM 2 at 2000°F. The small amount of boron in the boron steel greatly enhanced hardenability when the samples were austenitized at 1550°F. The low hardenability of the boron plus nitrogen steel showed that nitrogen eliminated the boron contribution to hardenability. Both steels containing nitrogen, with and without boron, exhibited lower hardenability than the base composition when quenched from 1550°F.

Jan 1, 1958

By L. R. Plitt, E. O. Lilge

Tests carried out with both kaolin and silica slurries show that flocculants of the polyacrylamide type can be used to improve the thickening performance of hydrocyclones. This thickening improvement demonstrates that contrary to previously held theories, flocs can be formed which are capable of resisting the shear forces in a hydrocyclone. For the 1.25-in.-diam cyclone used, optimum thickening occurs when the flocculant solution is injected into the slurry stream at or near the feed inlet. Hydrocyclones offer many distinct advantages over gravity thickeners. These advantages include simplicity, low initial and operating costs, small space requirements, and flexibility of operation. In spite of these advantages hydrocyclones have not been widely used as thickeners. The main reason for their lack of application is that hydrocyclones are unable to efficiently remove semicolloidal particles (less than 5 microns) from the suspending solution. In gravity thickeners, the fine particles can be induced to form particle aggregates, or flocs, which have the settling characteristics of large particles. In the hydrocyclone, however, it was always assumed that the existence of shear would prevent the formation of flocs.1-3 Thus, if no floc structure is retained, the thickening hydrocyclone must be designed so that its separation size is below the size of the smallest particle to be recovered. To obtain a very small separation size requires the formation of very high centrifugal forces, which necessitates the use of small-diameter cyclones. Small hydrocyclones have, in turn, very low throughput capacities which render them impractical for many industrial thickening applications. Thus, if the effects of flocculation cannot be utilized, the usefulness of hydrocyclones as thickeners remains limited to pulps which contain no very fine particles. It is well established that most substances acquire a surface electric charge when brought into contact with an aqueous medium. The repulsive interactions between similarly charged particles act to prevent flocculation. One method of flocculating a dispersion is to neutralize the repulsive surface charges by the addition of an electrolyte. The reduction of the electrostatic surface charge (Zeta potential) then permits the universal van der Waals attractive forces to operate between the atoms of the various particles and form particle aggregates. The lime additions used by thickener operators promotes flocculation by this mechanism. A second method of flocculating a dispersion is by the addition of long-chain macromolecules. In this case flocculation is brought about by a bridging mechanism in which the molecules are adsorbed with part of their length on two or more particles, thus forming a molecular bridge between the particles.4,5 The molecules also form bridges between themselves when a single particle is bonded to several polymer molecules. The type of bonding between the flocculant molecule and the particle may be hydrogen bonding, chemical bonding, or electrolytic attraction.6 The flour and glue which are used as thickener additives are believed to promote flocculation in this manner. In the past decade synthetic long-chain polymers with extremely high flocculating capabilities have been developed. The flocs formed by these new polymeric flocculants are larger and more shear-resistant than those formed by the presence of electrolytes.7 The advent of these flocculants raises the question: Are the flocs formed by these synthetic polymers stable enough to resist the liquid shearing forces in a hydrocyclone? The investigations reported in this paper were carried out in order to provide some answers to this question. EXPERIMENTAL WORK For the bulk of the test work a 5% slurry of commercially available kaolin with an average particle size of 5 microns was used. An initial evaluation of the available flocculants was carried out to determine which flocculant formed the most shear-resistant flocs. A combination of the techniques used by Healy7 and Booth8 was used for this purpose. This initial study revealed that the neutral high-molecular weight polyacrylamides produced the most shear-resistant flocs. One of these flocculants, Separan MGL*, was selected and then used for all the hydrocyclone tests. The flocculant was dissolved in water and added to the hydrocyclone as a dilute solution.

Jan 1, 1968

By D. S. Bloom

RECENTLY a report has been published on an investigation of the MO-RU system by E. Raub.&apos; In this report it is stated that below approximately 1200°C the system consists of two terminal solid-solution phases and the intervening two-phase field; at 1200°C and above, an intermetallic compound labeled Mo,Ru, makes an appearance. Along with some other little known systems in which it was considered possible for a u phase to form, the Mo-Ru system had been under investigation in this laboratory. Since molybdenum and ruthenium have very high melting points and also since ruthenium is expensive, the investigation was confined to X-ray diffraction by sintered powder compacts. The compositions which were studied were (in atomic percentages): 75 Mo-25 Ru, 67 Mo-33 Ru, 50 Mo-50 Ru, and 25 Mo-75 Ru. All compacts were made from the pure powders, and no chemical analyses were attempted. Each compact weighed about 5 g. All annealing was done in evacuated Vycor capsules, and even though the capsules completely collapsed at 1250°C, they still admitted no air. The results of this investigation in general corroborate the work of Raub. Up to 1150°C the two terminal solutions and the intervening two-phase field were found, and at 1200°C and above an intermetallic compound was found. However, the composition limits of the compound were estimated to lie close to 70 atomic pct Mo rather than 62.5 atomic pct Mo as Raub had reported. At least the X-ray diffraction results indicated that the 75 atomic pct Mo specimen consisted of the molybdenum solid solution plus the compound, while the 67 atomic pct Mo specimen consisted of the ruthenium solid solution plus the compound and the equiatomic composition contained only very little of the compound. The most interesting observation, however, was that the diffraction pattern of the compound was similar to that of the well known u phases, except that unusually large lattice constants were indicated. The d-values, or interplanar spacings, of the diffraction lines (as produced by filtered copper KCX radiation) of the compound are given in Table I, as determined from specimens annealed at 1250°C for 9 hr and then quenched in water. Also shown are the lines of the Mn-Mo u phase as given by Decker, Waterstrat, and Kasper,&apos; the lines of the Fe-Mo a as given by Goldschmidt," and the lines of the Mo-Ru phase multiplied by constants in order to make comparison with the Mn-Mo and Fe-Mo patterns easier. These results indicate that the compound in the Mo-Ru system is apparently isomorphous with the other o- compounds. The rather large lattice constants of the Mo-Ru a phase are acceptable in view of the comparatively large size of the constituent atoms. The data in Table I for the Mo-Ru compound check quite well with those given by Raub, not shown here, though there are some discrepancies between the two sets of data in the estimated intensities of a few lines. Although very little is known at present about this u phase, there are some things which may be pointed out, mainly in comparison with other better known u phases. Even though molybdenum and ruthenium are in the same columns in the Table of Elements as chromium and iron, respectively, the Mo-Ru u phase contains much more molybdenum than ruthenium, while the Cr-Fe u phase centers around or very nearly around the equiatomic composition; furthermore, the Mo-Ru u is stable only above approximately 1200°C, but the Cr-Fe u is stable only below about 825 °C. With respect to its being unstable below 1200°C, the Mo-Ru u is similar to the other binary molybdenum u phases in the Co-Mo and Fe-Mo systems. Similar to the latter two systems, the Mo-Ru u apparently exists over a rather narrow composition range, whereas the Cr-Fe u at lower temperatures is stable over a much wider composition range. The Mo-Ru u thus is closer to the other molybdenum u phases than to the Cr-Fe cr phase. The most striking feature of the Mo-Ru u phase, however, is the absence of any of the transition elements of the First Long Period.

Jan 1, 1956

By F. J. Haller

IN 1943, we found, in the new Mather operation, a very unusual and disappointing condition in the footwall rock where all of our main haulageways were to be located. With the exception of a few hundred feet out of the thousands then planned and since driven, all of the openings require support. In general, the ground is not particularly heavy, at least by our standards, but it must be supported and the back carefully covered. Also, our operations require rather wide plat openings (16 to 18 ft) and rather flat curves at the turn-outs, all of which adds to the problem. When this completely unforeseen condition was discovered, ordinary timbering was the only answer, because of the impossibility of obtaining adequate steel supplies in time due to war shortages. Then by the time steel supplies were obtained and a practice developed, we found ourselves with between four and five miles of main haulage drifts and plat openings of a permanent nature, all of which were supported by hardwood timber, some of which had already rotted to an unsafe degree. Also, our drifting program was adding some two miles per year to the above figure. F. J. HALLER, Member AIME, is Superintendent, Mather Mine, Cleveland-Cliffs Iron Co., Ishpeming, Mich. AIME Columbus Meeting, September 1949. TP 2840 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Aug. 22, 1949. Revision received Jan. 17, 1950. To give all of the details of our experiments, studies, and experiences would fill a large book, but we were satisfied that our organization had done an excellent job, starting from scratch. You can appreciate our surprise when we discovered that we had added very little to an existing record. Attention was called to a footnote in a copy of "Carnegie Pocket Companion" year 1923. The note read: "Full information as to uses of H-Beams is given in pamphlet entitled &apos;Steel Mine Timbers.&apos; " A search of our Engineering Library brought to light a pamphlet printed in 1911 showing extensive use of steel for this purpose. Except for welding in place of riveting, we have added very little to the designs in that book. We have, however, developed an experience which proves, at least to our own satisfaction, that steel mine supports pay off under the proper conditions. We are now convinced, in spite of the relatively high initial cost of materials, that steel sets, because of comparatively low installation cost, are actually cheaper than either treated or untreated wood sets, if they are properly designed and adapted. Several Sections in Use: Convenience guided our first experiments in steel sets, since for a number of years, we had used the 4-in. WF, 10 lb per ft section in 10-ft lengths as safety forepoles along with wood forepoles. This section replaced the 40-lb rail which had formerly been used for the purpose. Having the 4-in. WF sections on hand, it was natural that our first experiments in steel sets involved their use. Later, the rolling of the 10-lb section was discontinued in favor of the much stronger 13-lb section, which is now standard for both legs and caps in areas of no particular weight, but which, none the less, require permanent support. Our experiments involved the use of the 10- and 13-lb sections as legs and 6- and 8-in. I beams, 16 and 23 lb per ft, respectively, as caps. Experience soon indicated that, if the ground were heavy enough, and the opening wide enough to require a cap stronger than 13-lb, the 8-in, 23-lb should be used, eliminating the 6-in. I beam. We now know that the 8-in. WF section of the same weight, which we propose to use in the future, is considerably stronger for the amount of money involved. Comparative Strengths: Tables I to IV giving strengths of several species of timbers as compared with the structural sections that we now use have been prepared in accordance with accepted practice. Experience indicates that failure due to compression perpendicular to the grain of the wood does not destroy the effectiveness of a wood set frequently enough to be a practical factor. Therefore, no table of these values is included.

Jan 1, 1951

By G. E. Keller

In connection with the work of Committee D5, Coal and Coke, of the American Society for Testing and Materials in developing new standards and improving old standards, series of tests were made to check the variance of sample preparation and analysis of American coals. Table I in the "Tentative Method of Preparing Coal Samples for Analysis - 02013-62T" is rather complicated, and the tests were designed to develop data for the simplification of this table. An allowance of 20% of the total variance of sampling and analysis for the sample preparation and analysis steps was used. Also, instead of coals being grouped into ash ranges, they were grouped as washed and raw (unwashed) coals. As a result of these tests, a simplified Table I for Tentative Standard 02013 has been proposed. A standard test for laboratories to check their variance of sample preparation and analysis has been developed. Committee D5 on Coal and Coke of the American Society for Testing and Materials has been making a study of all standards applying to coal for the purpose of improving and bringing them up to date and for breaking some of the existing standards covering a number of tests into single standards. As an illustration, sample preparation is now partly covered in ASTM Designation D492-48, Sampling Coals Classified According to Ash Content, and partly in ASTM Designation D271-58, Laboratory Sampling and Analysis of Coal and Coke. The latter contains, in addition to parts of sample preparation, methods for determining Moisture, Ash, Volatile Matter, etc. Although revision of sampling methods and sample preparation methods are now assigned separately, it is possible that they may end up as one standard. One of the first new Tentative Standards developed as the result of these studies was ASTM Designation D2013, Tentative Method of Preparing Coal Samples for Analysis. Although this method is quite an im- provement over that in the old standards and gives very specific instructions, Table I (attached) is quite complicated and rather hard to understand. In order to take advantage of reduced quantities or weights, it is necessary to know the ash content within rather narrow limits before sample preparation and no distinction is made as to whether the coal is cleaned or uncleaned. No limits of accuracy are assigned to the sample preparation and analysis. The total over-all accuracy of sampling, preparation and ash determination as given in D492-48 has been specified for commercial sampling procedure as follows: "This procedure is intended for an accuracy such that if a large number of samples were taken from a single lot of coal, the test results in 95 out of 100 cases would fall within ? 10 per cent of the average ash content of the sample." Although Appendix 11, Method for Determining the Over-All Variance of Reduction and Analysis in the Tentative Methods for Mechanical Sampling of Coal, ASTM Designation D2234-63T, does give a method for determing the over-all accuracy of preparation and analysis expressed as variance and also the F test, it does not permit the determination of the variance at the various stages of reduction or of the ash determination. It was decided in 1961 to ask a number of laboratories to run a series of tests for the purpose of determining the variance at various stages of reduction and analysis with the view of simplifying Table I of the Tentative Standard D2013-62-T. This paper is a record of this series of tests with recommendations which resulted from the tests. At the same time and preceding these tests the International Organization for Standardization under Committee TC/27 WG 7 was studying the same problem. Tomlinson1 of England and Dr. paul2 of West Germany had made studies giving quite a bit of information. Also Schwerd and coryel13 published some information which was the main basis for the Mechanical Division provision in ASTM Tentative Standard D2013-62T, Table I. In checking with the various laboratories which offered to cooperate in these tests, none was found which used mechanical division through the entire preparation procedure. It was then decided to use riffles at all stages with the thought that if riffles gave satisfactory variances, approved mechanical

Jan 1, 1965

By F. J. Haller

IN 1943, we found, in the new Mather operation, a very unusual and disappointing condition in the footwall rock where all of our main haulageways were to be located. With the exception of a few hundred feet out of the thousands then planned and since driven, all of the openings require support. In general, the ground is not particularly heavy, at least by our standards, but it must be supported and the back carefully covered. Also, our operations require rather wide plat openings (16 to 18 ft) and rather flat curves at the turn-outs, all of which adds to the problem. When this completely unforeseen condition was discovered, ordinary timbering was the only answer, because of the impossibility of obtaining adequate steel supplies in time due to war shortages. Then by the time steel supplies were obtained and a practice developed, we found ourselves with between four and five miles of main haulage drifts and plat openings of a permanent nature, all of which were supported by hardwood timber, some of which had already rotted to an unsafe degree. Also, our drifting program was adding some two miles per year to the above figure. F. J. HALLER, Member AIME, is Superintendent, Mather Mine, Cleveland-Cliffs Iron Co., Ishpeming, Mich. AIME Columbus Meeting, September 1949. TP 2840 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Aug. 22, 1949. Revision received Jan. 17, 1950. To give all of the details of our experiments, studies, and experiences would fill a large book, but we were satisfied that our organization had done an excellent job, starting from scratch. You can appreciate our surprise when we discovered that we had added very little to an existing record. Attention was called to a footnote in a copy of "Carnegie Pocket Companion" year 1923. The note read: "Full information as to uses of H-Beams is given in pamphlet entitled &apos;Steel Mine Timbers.&apos; " A search of our Engineering Library brought to light a pamphlet printed in 1911 showing extensive use of steel for this purpose. Except for welding in place of riveting, we have added very little to the designs in that book. We have, however, developed an experience which proves, at least to our own satisfaction, that steel mine supports pay off under the proper conditions. We are now convinced, in spite of the relatively high initial cost of materials, that steel sets, because of comparatively low installation cost, are actually cheaper than either treated or untreated wood sets, if they are properly designed and adapted. Several Sections in Use: Convenience guided our first experiments in steel sets, since for a number of years, we had used the 4-in. WF, 10 lb per ft section in 10-ft lengths as safety forepoles along with wood forepoles. This section replaced the 40-lb rail which had formerly been used for the purpose. Having the 4-in. WF sections on hand, it was natural that our first experiments in steel sets involved their use. Later, the rolling of the 10-lb section was discontinued in favor of the much stronger 13-lb section, which is now standard for both legs and caps in areas of no particular weight, but which, none the less, require permanent support. Our experiments involved the use of the 10- and 13-lb sections as legs and 6- and 8-in. I beams, 16 and 23 lb per ft, respectively, as caps. Experience soon indicated that, if the ground were heavy enough, and the opening wide enough to require a cap stronger than 13-lb, the 8-in, 23-lb should be used, eliminating the 6-in. I beam. We now know that the 8-in. WF section of the same weight, which we propose to use in the future, is considerably stronger for the amount of money involved. Comparative Strengths: Tables I to IV giving strengths of several species of timbers as compared with the structural sections that we now use have been prepared in accordance with accepted practice. Experience indicates that failure due to compression perpendicular to the grain of the wood does not destroy the effectiveness of a wood set frequently enough to be a practical factor. Therefore, no table of these values is included.

Jan 1, 1951