Search Documents

By H. J. Beattie

R. L. Stegman and M. R. Achter (U.S. Naval Research Laboratory)—In a study of the surface structures developed in the fatigue of nickel at low strains as a function of temperature, we have obtained similar results.3 As our apparatus permits fatigue tests to be conducted in vacuo, there was no masking of the surface at high temperatures by oxidation so that the structures there could be observed directly. The relatively few broad slip bands observed at room temperature gave way at 300°C to a large number of uniformly distributed and narrower slip bands. At 550°C deformation began to concentrate around the grain boundaries and progressively increased up to 800°C. In addition fatigue strength was observed initially to increase with increasing temperature up to about 600°C due to the effectively increased ductility caused by the dispersal of fatigue damage. The fatigue strength then decreased at higher temperatures as grain boundary cracking dominates. Maria Ronay, W. H. Reimann, and W. A. Wood (authors' reply)— The authors are pleased to note that R. L. Stegman and M. R. Achter reach similar conclusions from their study of surface slip on nickel. However, they would emphasize that their own conclusions are based on what is shown by study of specimens that have been sectioned and that this study also shows that surface slip is not necessarily representative of what happens below the surface.

Jan 1, 1965

Discussion of the paper of Herbert F.. Miller, Jr., presented at the New York meeting, February, 1913, and printed in Bulletin No. 75, March, 1913, pp. 409 to 413. HENRY D. HIBBARD, Plainfield, N. J.:-Looking at the illustrations, it seems to me that a furnace made with the width of port that is shown here would not be a good working furnace. The economy of brick and gas might be all right, but I do not think it would melt the steel properly. I should say that the flame would not spread out suitably to fill the whole hearth of the furnace, and there would be undue waste, and it seems to me that it would be an undesirable furnace to adopt. The question as to whether a producer-gas flame would lie down in the furnace, hugging the bottom better than the natural-gas flame, is settled, not so much by the specific gravity of the gases themselves, as by the relative temperatures at which they enter the laboratory of the furnace. We know in that case that producer gas would be lighter than a natural gas which had not been run through a regenerator and expanded four or five volumes in consequence. I would like to hear what Mr. Miller has to say about the action of the flame spreading properly over the charge to give good metallurgical results in the form of furnace which he presents.

Jan 5, 1913

The Industrial Minerals Div., of the AIME meeting scheduled for Nova Scotia Sept. 8-12, 1953, promises to be one of the outstanding gatherings ever attended by the group. Complementing the educational value of technical sessions will be the superb fishing, boating, golfing, and tennis facilities. [ ] Sponsor of the meeting is the Nova Scotia Mining Society. The Canadian Institute of Mining and Metallurgy and Industrial Minerals Div., AIME have been invited to participate. The land immortalized by Longfellow's poem, Evangeline, still contains much of the forest primeval-enough to make it a wonderful vacation spot for delegates and their families. Its scenic beauty is almost unmatched in the area north of the border. Quoting from the Nova Scotia tour book; "Nova Scotia, once known as Acadia, is 374 miles long, from 600 to 100 miles wide ... Excepting the Isthmus of Chignecto, 17.5 miles wide, the province is entirely surrounded by water, no portion being more than 50 miles from the sea . . . has 4625 miles of coastline, guarded by 356 lighthouses and fog alarms. The province is renowned for its picturesque coastline, its harbors dotted with islands, its deep valleys and multitude of beautiful lakes." A progress report on the plans for the meeting will be made monthly. Thus far, technical sessions will be held at Keltic Lodge, Ingonish, N. S. The lodge will also be the starting point for many of the field trips and social events which are in various stages of planning and development.

Jan 1, 1952

By R. A. Marriot

The steam-generating plant at the Garfield smelter of The American Smelting and Refining Co. consists of two divisions in which the boilers are classed as direct-fired or waste-heat. The direct-fired boiler plant consists of eight 330-boiler hp. type K-19 and S-I 7 Stirling boilers located in the boiler room adjacent to the power house, and two 330-boiler hp. Stirling type K-19 boilers in the reverberatory building, which formerly were connected to a reverberatory furnace but now are arranged for direct firing. All direct-fired boilers are now fired with natural gas. The waste-heat boiler plant consists of all units connected to reverberatory furnaces, and receiving heat from the exit gases therefrom. In this classification there are two 490-boiler hp. Erie City vertical water-tube boilers, and six 330-boiler hp. type K-19 Stirling water-tube waste-heat boilers. Each furnace has boilers arranged in battery setting. The boilers are directly in front of the furnace and connection is made through a short uptake and flue (Fig. 1). The Stirling boiler settings rest on concrete foundations at ground level, with the furnace uptake and flue at a low elevation. The Erie boilers are carried on steelwork some 15 ft. above ground level, and stand against the face of the uptake with no connecting flue. The constructional requirements of a larger furnace dictated this type of setting.

Jan 1, 1934

By R. L. Stegman, M. R. Achter

R. L. Stegman and M. R. Achter (U.S. Naval Research Laboratory)—In a study of the surface structures developed in the fatigue of nickel at low strains as a function of temperature, we have obtained similar results.3 As our apparatus permits fatigue tests to be conducted in vacuo, there was no masking of the surface at high temperatures by oxidation so that the structures there could be observed directly. The relatively few broad slip bands observed at room temperature gave way at 300°C to a large number of uniformly distributed and narrower slip bands. At 550°C deformation began to concentrate around the grain boundaries and progressively increased up to 800°C. In addition fatigue strength was observed initially to increase with increasing temperature up to about 600°C due to the effectively increased ductility caused by the dispersal of fatigue damage. The fatigue strength then decreased at higher temperatures as grain boundary cracking dominates. Maria Ronay, W. H. Reimann, and W. A. Wood (authors' reply)— The authors are pleased to note that R. L. Stegman and M. R. Achter reach similar conclusions from their study of surface slip on nickel. However, they would emphasize that their own conclusions are based on what is shown by study of specimens that have been sectioned and that this study also shows that surface slip is not necessarily representative of what happens below the surface.

Jan 1, 1965

By Albert Burch

AN analysis of this subject demands a study of the theory and practice of the present system, conclusions as to its merits, and recommendations for remedying its defects if any be found. Theory of the Present Law The theory of the present law with reference to lode locations contemplates the existence upon the surface of mineral-bearing veins which have clearly marked boundaries, and which can be so readily traced that a locator may immediately mark the boundaries of his 600 by 1,500 ft. claim in such a way that the vein will pass through both of its end-lines. It also supposes that, having discovered such a mineral-bearing vein, the locator will at once post a notice upon such discovery, mark the boundaries of his location in such a manner that they can be readily traced, and from that time forward have absolute title to the ground embraced within such boundaries, as against every person except the United States. For initiating title to placer ground, the law presupposes the discovery of a valuable mineral deposit; but not necessarily in place, as in the case of lode claims; and the location must be made to conform "as nearly as may be" to the legal subdivisions of the United States public land survey. When the placer law was extended to include the acquisition of title to oil lands, no exception was made as to the necessity for the discovery of valuable mineral in advance of location!

Jan 6, 1914

By H. M. Chance

THE present value of most coal properties resides largely in the coal remaining to be mined, which thus constitutes the most important asset. The object of this paper is to discuss methods commonly used in computing the value of mineable coal. To distinguish clearly between such coal values and the values of other property, the several kinds of property values may be divided into classes; this is necessary to avoid unintentional omissions of items of importance. VALUE OF COAL RESERVES Judicial decisions prescribe, and appraisers commonly accept, current sales value as the preferred means for determining the value of transferable property. With few exceptions a property is worth the sum that can be realized from its sale by a willing seller to a willing buyer, a sale in which compulsion urges neither party, and between whom there is no community of interest to fix a value; or it is worth at least as much as a responsible buyer will offer for it. Actual sales of like property or bids from responsible buyers for the property, or for substantially like property, are the best established methods for determining values. Only in the absence of such sales or bids can valuations by other methods be entertained, and only for reasons of weight can sales values be set aside. Sales of coal in the ground, as customarily carried out through lease, under royalty agreements, are therefore the most trustworthy means available for determining the value of coal reserves.

Jan 6, 1926

Discussion of the paper of M. B. YUNG, presented at the Pittsburgh meeting; October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2451 to 2458. T. T. READ, New York, N. Y.-I might .point out that this paper of Mr. Yung's is on a field that is comparatively little known. It is not as well known as the Kochiu tin field, of Yunnan, which is probably the third . in tin output of the world. This field under discussion is considerably further west and the tin which is produced here is, according to Mr. Yung, of somewhat higher grade than the Yunnan tin, and is used by the refiners at Hong Kong to improve the grade of the Yunnan tin. Most of you know that the tin from the Yunnan is shipped to Hong Kong, where it is refined and shipped to Europe. Mr. Yung points out that the Fu Chuan deposits are entirely alluvial and not found in any veins. They .differ in that from the Kochiu deposits, which Leclere says are "nullement alluvionels; leur origéne filonienne est de plus evidentes." Granite is the country rock here; doubtless the tin occurred in veins in the granite, and the deposits have resulted from the disintegration of the granite. This is a country of strong erosive agencies. The country is semi-tropical, and the rainfall is heavy, so that one would naturally expect deep surface erosion of this kind.

Jan 4, 1915

By Kent E. McElhattan

Selecting efficient machinery for an underground mining operation is a highly skilled art that still depends largely on human judgment and experience. In a coal mine, for example, there is no better way to predict the results of operating with a cutting machine or a continuous miner than to go underground with a sharp-pointed miner's pick. The trained eye can detect the depth of point penetration, cleavage planes, roof and floor strata, and many other conditions impossible to determine in a laboratory. Even so, however, an entirely new set of conditions may lie unexposed just a few feet behind the solid face. The candid truth of the matter is that practically nothing is known of the phenomenon of extracting a mineral from a solid. Consequently, the selection of mineral extraction machinery and systems must be based on results obtained elsewhere under apparently similar conditions. A recent study of the problem of equipment and system analysis was conducted in the coal mining regions of West Virginia. This state was chosen for study because it afforded representative sampling. The 172 coal mines investigated ecompassed seam heights ranging from less than 30 in. to over 84 in. and covered virtually all known coal mining conditions except two. The exceptions are the extreme pitch of coal seams in the western United States and British Columbia and the "bumps" encountered in the Rocky Mountains. Both of these extreme conditions are worthy of individual study.

Jan 7, 1969

GEO. F. COMSTOCK,* Niagara Falls, N. Y. (written discussion?).¬A study of this paper raises a question on which it is hoped Mr. Stork will throw more light; that is, why does an oxygen content generated on poor melting conditions have a deleterious effect on the properties of the iron, while an oxygen content generated by the oxidation of steel scrap in the cupola is beneficial to the strength and chilling ability? In each case the oxygen is absorbed at the same time and place in the process of melting and it is by no means clear why the superiority of semisteel should be assigned solely to its oxygen absorption, when oxygen absorbed without the steel addition is admitted to be injurious. It is not apparent why oxygen caused to be absorbed by the steel addition should not pro-duce the effects of burning, sluggishness, slag inclusions, gas occlusions, etc., the same as oxygen absorbed by the iron in the cupola for any other reason, and it would seen that other factors to which he has not given sufficient emphasis must enter into the author's results. To an impartial reader of this paper, who was most favorably inclined toward J. E. Johnson, Jr.'s theory of the improvement of cast iron by oxygen, the discrepancy in the author's reasoning or statements is difficult to accept, and it is hoped that an explanation will appear in the final discussion.

Jan 11, 1919

By V. R. Garflas, J. W. Ristori, R. V. Whetshel

Preliminary estimates indicate that world consumption of petroleum products and related fuels in 1937 shattered previous records with a figure of 1,920,000,000 bbl.; that is, 124,000,000 bbl. more than the 1936 total. The writers, as in previous years, have been unable to account for all the available supply in 1937. This "unaccounted-for" supply, which formerly was thought to go largely into storage in foreign countries, was close to 53,000,000 bbl. in 1933; 93,000,000 in 1934; 111,000,000 in 1935; 75,000,000 in 1936 and 148,000,000 in 1937. As this discrepancy between supply and demand continued year after year, it became evident that other reasons than additional foreign stocks were responsible for it. It can now be stated that the "unaccounted-for" supply (see Table 1) goes to take care of: (1) consumption of petroleum products and related fuels for military purposes, the figures of which have been and are kept confidential by foreign countries, (2) additions to stocks to be consumed for military and nonmilitary purposes in foreign countries on which likewise no information is available, (3) errors incurred in the conversion of figures of production of crude oil, its products and related fuels from "weight" units, as used in Russia, for instance, to their American or "volume" equivalents and vice versa, and (4) to the lack of reliable statistics on production and consumption, particularly from Russia, the

Jan 1, 1938

DESPITE strikes, domestic production of copper and zinc in 1951 rose about 3 pct and 10 pct, respectively. Lead output fell only about 7 pct. Primary refined, including processed scrap and imported concentrates, was somewhat higher for zinc, and slightly lower for copper and lead. Prospects are for moderately larger mine and refined production in 1952 according to Standard & Poor's analysis of nonferrous metals. The survey goes on to report domestic copper prices averaged 14 pct higher in 1951, lead prices 30 pct higher, and zinc prices 32 pct higher. The 2¢ rise in zinc and lead ceilings in October will lift the average price in 1952 over 8 pet, assuming no further price change. Currently, OPS appears opposed to raising the 24 ½ ¢ copper ceiling to the 24 ½ ¢ maximum on imported metal. The steep premiums in world markets are likely to be reduced in 1952. Sales in 1951 were at new peaks. A further moderate rise is indicated for 1952. Earnings of the industry were at a new high in 1951. The increase for companies covered in the survey was perhaps 25 pet, despite a tax rate of about 53 pet, against about 40 pct. in 1950. Relatively maintained to moderately higher earnings are currently indicated for 1952. About two thirds of the companies covered in the survey raised dividends, including extras, in 1951. In general, maintained payments appear probable in 1952.

Jan 1, 1952

W. Morton Webb, Germiston, Transvaal, South Africa (communication to the Secretary*):—The experience of Mr. Boeh-mer in the Leadville district and his reputation as an engineer assure the interest of anything he may write on the ore-bodies of that district; and all engineers who have operated in Leadville will agree that the theory of the origin of the Leadville deposits, as given by Mr. Emmons in his famous monograph, does not adequately explain the genesis of all the deposits. The solutiou of the problem does not, however, appear to be quite so simple as Mr. Boehmer would make it; and the advance pamphlet issued by the U. S. Geological Survey, pending the completion of the main report, shows that there is still much ground for controversy. No doubt the later eruptive0 had a greater influence on the deposition of the ore-bodies than was thought at the time of the first investigation by the Survey; but it has always appeared to me that the influence exerted by these dikes mas more in the nature of a physical than a chemical one. The weight of evidence in recent years is mostly in the direction of ascension rather than lateral secretion; and one of the strongest evidences is the fact that most of the ore-bodies lie under one of the comparatively impervious layers which help to make up the structure of these hills.

Jan 1, 1911

Discussion of the paper of L. C. MORGANROTH, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2345 to 2352. D. T. DAY, Washington, D. C.-I would like to hear some further detail as to the California deposits. L. C. MORGANROTH, Pittsburgh, Pa.-We have examined the California deposits at various times; I have been over practically all of them myself. These deposits are all of the massive variety. While it is possible that it could be mined and used for metallurgical purposes, it is not feasible because it costs too much. At the present time magnesite which is mined in California is used in the making of plaster, or by the paper trade. Careful figures show that if the California magnesite could be delivered to Atlantic seaports in the crude state at not over $4 a gross ton, and assuming that it would give the same results as the Austro-Hungarian magnesite, it would be cheaper to use the latter. It is also more difficult to dead-burn the massive magnesite, for while it starts to give up its gas readily, the difficulty consists in driving off the last few per cent., and unless this is driven off the magnesite will absorb C02 from the air, so that in a few months it may have 10 or 12 per cent. DAVID T. DAY.-How is the Austro-Hungarian supply at the present time ?

Jan 4, 1915

By Beverley S. Randolph

The coal-measures of George's Creek coal-region, in Maryland, lie in a comparatively flat synclinal basin, about 4 miles wide. The dip of the measures is, in places near the edge of the basin, as much as 20 feet in 100. The Pittsburgh seam, known locally as the " Big Vein," is the only seam worked at the present time. Ocean No. 3, one of the large mines of the Consolidation Coal Company, has its opening on the outcrop of the Pittsburgh seam, in a ravine which cuts into this seam to such an extent as to bring this opening to within a mile of the axis of the basin. After working all the coal to the rise of this point, the mine was further developed by extending a slope down the dip of the seam, making such an angle with the line of greatest dip as to give a grade varying from 1 to 10 per cent., down which the empty cars carry a rope from a single-drum winding-engine. The coal was worked from each side of this slope in successive Iifts during its progress. From the top of the slope, for a distance of 4000 feet to the fourth lift, the " make " of water is drained by gravity through a heading into the adjoining mine. Below this point the water was pumped into this same heading, at the fourth lift, from which point, as before mentioned, it flowed by gravity.

Jan 1, 1895

By J. A. Holmes

It is a fact that is coming to be more widely recognized by the general public, as well as by members of the medical fraternity, that the health of persons living in our hill-country depends in no small degree upon the drinking water obtained, just as it has been found that the* use of pure water in the lowlands and swamp-areas of the Southern States results in practical immunity from malarial diseases. Hence the problem, how to obtain supplies of wholesome water for the towns and manufacturing establishments in the hill-country or Piedmont plateau-region of the Southeastern States, becomes one of considerable interest, the importance of which will continue to increase, as the favorable conditions for manufactures and agriculture in this region will make it, in the near future, the most thickly populated portion of the South Atlantic States. Water-supplies from Surface-streams are unquestionably of the first importance; and in the mountain counties, where the region is still largely forest-covered and the streams are swift and continually aerated by rapids and cascades, the water is of superior purity and clearness. This statement is also applicable to the more elevated and sparsely settled portions of the Piedmont plateau; but in the less hilly and more thickly settled portions of this region the streams are more sluggish, and the waters more muddy and less pure, owing to the fact that a much larger proportion of the surface is under cultivation.

Jan 1, 1896

By Andrew Button

INTRODUCTION This review deals with the controls exerted by unconformities on the stratigraphic and areal distribution of gold (and uranium) in Precambrian conglomerates. The relations described are drawn mainly from Precambrian basins in southern Africa, particularly the Witwatersrand Basin. The mining industry of South Africa started in earnest with the discovery of diamonds in 1866. Gold was first discovered in 1870, and in March of 1886, two out-of-luck prospectors stumbled across what was to become the world's greatest goldfield, in the vicinity of Johannesburg. George Harrison and George Walker sold their claims for a pittance and were heard of no more. The Witwatersrand goldfield has been in continuous operation since that time, some 150 mines having operated at one time or another. Deep mining technology developed here has allowed operations to proceed to depths approaching 13,000 feet. The Witwatersrand has produced some 55% of all the gold ever mined, and currently produces 60% of the world's supply, some 650,000 kg Au per year. To 1971, the Witwatersrand had produced some $32 billion of gold and $2 billion of uranium (when average prices were less than $35/oz. for Au and $10/lb. for U308). At present prices, the annual Witwatersrand production of close to 700,000 kg would be worth about $10 billion. Uranium was discovered in the Witwatersrand in 1923. In the $15-30/lb. bracket, the basin contains a reasonably assured plus

Jan 1, 1983

By Robert Anderson Cook

The subject of refractory materials occupies such an important position in all metallurgical works, and particularly in those of iron and steel, that any data concerning it must be of interest to the metallurgist. No apology is needed, therefore, for this attempt to describe the mining of fire-clay and the manufacture of fire-brick at one of the largest establishments in this country. Mount Savage is a small village situated in the northwestern part of the Cumberland coal basin, on the Cumberland & Pennsylvania Railroad, and at the foot of Savage Mountain, from which the village takes its name. Fire-brick have been manufactured here almost, if not quite, as long as in any place in America; and as the brick are still shipped to nearly half the States in the Union every month, the manufactory is probably the most generally known. In the year 1837, a company was formed called the Maryland & New York Coal & Iron Company. It built two blast-fiirnaces, the ruins of which still remain. It was in the construction of these filmaces that the first fire-brick made here were used ; and though the iron works ran but spasmodically, the brick works have been in constant operation ever since. From 1837 until 1846, the Maryland Coal & Iron Company, from then until 1548, the Lochiel Iron Co., and from 1848 until 1861, the Mount Savage Iron Co., ran the brick-works, and in

Jan 1, 1886

By C. K. McArthur

THE subject of classification is so broad that this discussion is con-fined to what the author believes is of prime importance in connection with proper grinding and classification. The years passed have witnessed many noteworthy changes in fine grinding and classification, which have been accompanied by a readjust-ment of ore-dressing flowsheets for the preparation of better ground and/or sized products at an expenditure of less. power, steel and main-tenance than formerly. Nowhere in the industry is more being done in the way of experimental work to lower costs than in grinding circuits, because, at best, grinding costs are high. Recent years have indicated that, on the average, finer grinding has a real application. Without careful preparation of the process feed, no operation can be highly efficient or successful. In an earlier paper, the findings of an extensive survey at representa-tive concentrators were presented1. Also, in the year of 1935, a technical discussion was given by Dr. J. V. N. Dorr (Some Notes on Classification Trends in America) before the Chemical, Metallurgical and Mining Society of South Africa. In both papers mentioned, much has been said regarding flowsheets, grinding and classification. The author is very familiar with these papers, having had considerable to do with the actual operation of the flowsheets, as well as large mills and classifiers in the work described. Some data from the second paper have been included in the following discussion.

Jan 1, 1937

By J. P. Manning

UNQUESTIONABLY, the outstanding feature of the piping for the sulphide plant is the large amount which had to be done in almost every size from instrument tubing to 84 in. OD pipe. In this article the piping will be considered under the main headings of Yard Piping and Building Piping. Tables I and II give data concerning the individual systems. In the case of yard piping the figures pertaining to lengths and weights are approximately correct; those for building piping are given only for the concentrator and smelter buildings where the amounts were the most extensive. Yard Piping The installation specifications for yard piping called for all sizes larger than 12 in. to have welded joints made with outside welding rings. This type of joint was selected over butt-welded joints because less time would be needed for lining up, damaged pipe ends would be less of a problem, and deflections up to 6° per joint could be made when necessary. These advantages were thought to outweigh the disadvantage of the greater amount of welding required. Yard piping in sizes of 3 to 12 in. was specified to have butt-welded joints made with inside welding rings which were intended to facilitate lining up and keep welding material out of the lines. Screwed connections were specified for sizes under 3 in. No protective coatings or wrappings were required on pipe to be buried because of the dry climate at Chuquicamata.

Jan 1, 1952