Search Documents

"The Butte, Anaconda & Pacific railway extends from Butte to Anaconda. The electrification comprises 30 miles of main line single track, and includes sidings, yard and smelter tracks. When complete the electrified trackage will total about 90 miles on a single track basis.The traffic conditions are unusually severe as they consist principally of hauling copper ore from the Butte mines to the smelters at Anaconda, as well as hauling all the mine supplies, lumber, etc., in both directions; this traffic amounts to approximately 5,000,000 tons of freight per year. The maximum grade against the load is .3 per cent and the maximum train consists of 50 loaded steel ore cars, weighing 3,400 tons. .The locomotive units, two of which will be used for freight trains, weigh approximately 80 tons each. In addition to the freight business, there will be a certain amount of passenger traffic.The power for operating the Butte, Anaconda & Pacific railway is generated by, the Great Falls Power company, and is transmitted to the sub-stations at 100,000 volts. The synchronous motors are supplied with power at a potential of 2,300 volts, 60 cycles, 3-phase. Voltage regulators are installed in each sub¬station to secure the benefit of synchronous condenser effect of the motors.The passenger and freight locomotives are exactly similar, with the exception of the gearing.The roller pantograph mounted on the top of the cab is operated by air from the engineers position.The adoption of the 2,400-volt apparatus for so important a system, where the conditions of operation are so severe, is interesting of itself, as indicating the trend that future electrifications of importance may follow. A trolley potential of 2,400 volts was only adopted after a thorough investigation of other systems already in operation."

Jan 1, 1913

By C. A. Hansen

Page Introduction............................206 Power Characteristics in Zinc Sulfate Electrolysis........... 207 Current Efficiency......................... 207 Corrosion Rates..........................216 Voltage Required by the Zinc Cell..................219 Power Requirements of the Zinc Cell ................221 Impurities in Zinc Electrolyte.....................222 Non-cumulative Impurities.....................223 Cumulative Impurities ....................226 Impurities in General........................228 Temperature and the Stability of the Zinc Cell..............229 Practical Expedients for Control of the Zinc Cell...........234 Acknowledgments...........................234 Appendix................................235 Discussion...................:.......... - 236 Introduction It has been the experience of the writer, during some five years' work with electrolytic zinc, that the zinc cell is perhaps more sensitive to impurities in the electrolyte than the analytical methods as yet developed for the chemical identification and determination of these impurities; but that, when proper purification methods have been applied to a given solution, the behavior of the cell is quite independent of the original sources from which the zinc sulfate has been derived. It has also appeared that the behavior of the zinc cell is the best and surest check on the correctness and thoroughness of the purification methods used, because it indicates the presence of both current impurities and cumulative impurities derived from the leaching of the ore; it also indicates whether these impurities are current or cumulative, at least in so far as they are of serious importance commercially.

Jan 1, 1919

By James Pollock

The possibility of colloidal deposition of cinnabar has been neglected. In opalite deposits cinnabar exists in particles within or near the colloidal size range. Colloidal processes have been admitted to be operative in hot springs and low-temperature deposits similar to most cinnabar deposits. Mercuric sulphide sols are stable to elevated temperature and pressure, and in nature probably are chiefly affected by the electrolytes in solution, dilution of colloid, and presence of protective colloids as silica. The stability of mercuric sulphide sols to electrolyte is measured, and shown to be greatly increased by dilution and by the protective action of silica. Mercuric sulphide sols follow the Schulze-Hardy valency rule, therefore the precipitating power of complex mixtures of electrolytes can be computed roughly. The stability of mercuric sulphide sols is shown to be greater than the equivalent precipitating power of the electrolytes in a hot spring depositing mercuric sulphide. It is concluded that finely divided or earthy types of cinnabar are colloidally deposited. Possibility of Collodial Deposition While colloidal solution has been suggested as a means of transport for a number of minerals, such as the sulphides of antimony, arsenic, and iron, it has been neglected in connection with mercury. This is surprising because there exists positive evidence that cinnabar is present in certain deposits in particles of colloidal or near colloidal size. Colloidal transport could result from either the rapid dilution or neutralization of alkaline sulphide solution bearing mercury coming in contact with deep ground waters, or from colloidal solution near the original source and subsequent flow to the point of deposition unchanged. That the dilution of a mercuric alkaline sulphide solution will precipitate mercury sulphide in colloidal form has been demonstrated a number of times and is easily confirmed. The dilution hydrolyzes the alkaline sulphide Na2S to the corresponding hydroxide and hydrosulphide NaOH and NaHS, and the diminution of the concentration of alkaline sulphide reduces the solubility. It is not the contention of this writer that colloidal deposition is the mode of transport of mercuric sulphide in all mercury deposits, but that the stability of a mercuric sulphide sol, as demonstrated below, in waters that are similar to those that have deposited mercuric sulphide necessitates consideration of this possibility in many deposits, especially those of the hot-spring and so-called opalite type. Evidence of Colloidal Deposition Ross1 has shown that most deposits of quicksilver are formed at low temperatures and pressures, and probably by solutions that have relatively simple chemical compositions. In most cases the solutions are probably similar to those observed in hot springs, and in two instances—at Steamboat Springs, Nevada, and Sulphur Bank, California—hot springs have been reported by Becker as actually depositing cinnabar.2 Opalite deposits were believed by early investigators to be surface phenomena

Jan 1, 1949

By Lester Uren

WITH the depletion of our older, and relatively shallow, oilfields and the necessity for securing new production from deeper horizons, much attention is being given to the improvement of oil-well pumps in order that they may function satisfactorily under the more difficult conditions imposed by increased depth. Until recently, practically all of the world's petroleum was secured from wells less than 3000 ft. deep, whereas horizons are now being explored to depths of from 5000 to 7000 ft. in some of the more prolific fields, and it seems probable that the greater part of the future supply must come from depths in excess of 3000 ft. While much of the early production in a new field is obtained by natural-flow methods, when the stimulus of high gas pressure fails, recourse must be had to some method of pumping. The perfection of a pump capable of economically and efficiently lifting oil from depths ranging from 3000 to 7000 ft. is therefore a matter of prime importance to the oil-producing industry. This paper is offered as an estimate of the present state of development of the oil-well plunger pump and as a review of the general principles involved in its operation in deep-well pumping. A design for a new type of oil-well pump embodying several novel features, is also described.

Jan 9, 1925

By Gifford White

Considerable attention has been directed in recent years to methods of electric prospecting other than the conventional direct-current techniques. It has been extensively recognized that electrical data of a more general nature than that possible by direct-current methods might be useful in geophysical studies. To this end, a number of different types of electric currents have been employed, such as single-frequency alternating currents, square-topped periodic current waves,4 periodic surges of a less specific nature,s and suddenly applied direct current.1,2 Yet, to the author's knowledge, little analysis of these different types of driving currents has been made from the standpoint of network theory to determine just what typc of currents would give the most useful data, and, most important of all, to determine the relation of the data taken by one method to those of another. Without touching on the actual theoretical problem of how currents flow in the earth under specified boundary conditions, some very useful information can be obtained from the study of the fundamental integral equations of electrical networks, throwing light on the problem not ordinarily appreciated by the field worker. Some manipulation of the standard network equations will be made, with the sole purpose in mind of developing expressions leading to practical results. Suppose that four points in the earth have been located and it is wished to obtain the most useful type of electrical data by inserting current into two of them and measuring the potential developed between the other two. The first problem that arises is that of which pair of the four shall be chosen as current grounds. In the direct-current case, where only steady potentials are measured, the selection is of little consequence, but as soon as currents varying with time are used at the current grounds, a new effeet arises. The fact that a varying current is flowing in the current-carrying conductor between the current grounds means that magnetic and electric fields varying with time will be produced

Jan 1, 1940

By R. J. Wysor

MoRe than two years ago, in making efficiency tests on our hot-blast stoves, I was surprised to discover a marked difference in temperature as indicated by a pyrometer inserted near a stove on blast, and the regular recording instrument situated near the bustle pipe. A special hole was then provided at the junction of the hot-blast main and the bustle pipe, and portable pyrometers with bare fire ends were used, both at this point and in the stove necks. I had occasion to make a number of such tests on various stoves on the same, furnace, the difference in temperature as shown by the two pyrometers varying chiefly with the temperature of the blast, and the distance of the stove from the furnace. However, this difference was always great, often averaging above 100" F., for the entire period of a stove on blast. Later, experiments were made with similar results on another group of stoves. The pyrometers used were properly standardized and checked against each other before and after each test. However, there was still a slight doubt as to the accuracy of the results obtained, as subsequently explained. But I have obtained corroboration of the magnitude of heat losses from blast-furnace hot-blast mains from two independent sources. I have learned from H. A. Brassert, Superintendent of Blast Furnaces, South Works, Illinois Steel Co., that he has recently done some experimental work similar to my own, and found temperature drops of the same order of magnitude. Also, C.,R. Lyle, of the Armstrong Cork Co., has made some interesting theoretical calculations, based on the thermal conductivity of fire brick, for the particular conditions of several of our tests; and his theoretical interpolations, all facts being considered, check our actual observations fairly well. I understand that Mr. Lyle expects to publish the results of his investigations. Method of Conducting the Tests The location of the pyrometer fire ends is shown in Fig. I, a plan of Bethlehem Steel Co.'s "G" blast furnace, hot-blast stoves, and main. Bare fire ends were used at both positions "A" and "B," being inserted

Jan 1, 1916

By H. H. Kellogg

An invitation to address you on the occasion of the one-hundredth anniversary of AIME represents an honor, a challenge and an opportunity: an honor that you judge me worthy; a challenge that I present to you a picture of extractive metallurgy in the years ahead that contains some ideas of value; and finally, an opportunity for me to express some deeply felt beliefs about our profession and our industry. My topic concerns the technology of metal production in the future - the processes, new and old, that will be used to extract metals. The nature of these processes will be shaped by many forces - some technical, some economic, some political or social. A forecast of future technology must recognize the role of each of these forces, and I have endeavored to do this in the analysis that follows. In brief, my outline consists of an analysis of the forces (perhaps better called "problems") that will influence the future of our industry, followed by consideration of likely lines of technological development to meet them. Let me dwell for a moment on the nature of this industry and the profession that serves it. I have been engaged in the profession of extractive metallurgy - teaching, researching and consulting - for 30 years. I have always found the subject stimulating and rife with challenges of a scientific, engineering, economic and socio-political nature. It is a big subject - it encompasses most of the elements of periodic table; we measure the U. S. production of six metals in millions of tons per year; new plant costs range to $100 million and more. The supply of metals from our extractive plants plays an essential role in our modern industrial economy. We could do without DDT, or phosphate detergents or 300-page Sunday newspapers; we cannot do without a huge and increasing supply of metals. The Basic Goal of Extractive Metallurgy Understanding of some basic forces that shape this industry can be gained by consideration of the question: What determines the utility of metals to man? We think immediately of the inherent properties of metals - strength, ductility, electrical conductivity and so forth - but these tell only part of the story. Metal price and the available supply play equally

Jan 1, 1971

By E. L. Bruce

The district of Patricia, in the province of Ontario, lies northwest of the Albany River and extends northward to Hudson Bay. Formerly this was the unorganized district of Keewatin, the southern part of which was divided in 1912 between the provinces of Manitoba and Ontario. The interprovincial boundary now runs north from Lake of the Woods for 275 miles and thence northeast 375 miles to Hudson Bay. This district is comparable in size to all the older part of Ontario south of the Canadian Pacific Railway east of Lake Huron—thus it is roughly one-third of the whole of the present provincial area. The central part of this great triangle is one of the least accessible parts of Canada. From it streams flow southward to the English River, southeastward to the Albany, northward to Hudson Bay and the Hayes River, and westward to Lake Winnipeg. None of the streams is large and canoe travel is not easy. The only industry it has ever had is the trade in furs. Until the development of the airplane on a commercial basis, the only means of travel was by canoe or dog-train. There is not a mile of railway in the whole district. The two areas to be dealt with lie in the southwestern part of Patricia. Red Lake is 50 miles east of the Manitoba boundary and 75 miles north of the transcontinental railway from Cochrane to Winnipeg. Woman Lake is 50 miles farther east and slightly farther north. The late Dr. D. B. Dowling, of the Geological Survey of Canada, visited Red Lake and spent some time there during his exploration survey from Lac Seul to Berens River in 1893. He also visited the Woman Lake basin during the same journey, but his examination of it was much less detailed, the great area covered by him during the one field season making it impossible to make more than a hurried reconnaissance. Some prospecting in the Red Lake district followed Dowling's exploration, but the distance from railway was too great for any systematic work to be done. In 1922, following the usual plan, the Ontario Department of Mines made a geological reconnaissance of the English River, following :in instrumental survey of that river and its lakes by the Department of Lands. A side trip was taken to examine the rocks of Red Lake described

Jan 1, 1928

By Nicholas J. Grant, Robert F. Wilde

TAYLOR and Floyd's"" work in establishing phase diagrams based on the elements Ni-Cr-Ti-A1 has led to an understanding of the precipitation hardening mechanism in alloys based on these elements. Nordheim and Grant4 concluded that in simple alloys, and where the aluminum to titanium atomic ratio was such that less than three out of five aluminum atoms were replaced by titanium, the precipitate on aging is the face-centered-cubic Ni 3A 1 phase, called They further found that increasing amounts of hexagonal ? phase, Ni3Ti, precipitated from these alloys when the titanium content exceeded the solid solubility of both matrix and Ni3A1. For alloys of Ni-Cr-Ti-Al, in which the titanium and aluminum contents each ranged from 0 to 4 wt pct, the titanium-rich was superior for strengthening to either pure ?' or 7. It was also noted that the combined titanium plus aluminum content (atomic pct) was a direct measure of the high temperature strength and overaging temperatures for these alloys.4 The present investigation was undertaken to extend existing data on precipitation hardening in the more complex commercial alloys containing higher titanium plus aluminum, and with significant quantities of cobalt, molybdenum, and carbon. Experimental Procedure Reforging of As-Received Bar Stock—The alloys were received as ground, forged bar stock. Chemical analyses and the as-received bar diameters are shown in Table I along with the ASTM grain size after the various treatments. All stock except the Waspaloy was reforged to % in. diam to gain material and to facilitate machining of stress-rupture specimens. Forging was carried out at 2100°F, and discontinued when the bar temperature fell to 1800°F. Heat Treatments—For experixental simplicity it was desirable to heat treat all of the alloys at, the

Jan 1, 1958

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metallurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939

By F. H. Newell

Measurements of the amount of water flowing in many of the larger rivers of the west have been made by the United States Geological Survey, and by this means the daily discharges of these rivers have been computed for a period of over two years. These measurements have been confined mainly to that part of the country commonly known as the arid region, where the rainfall is insufficient for the needs of plants most useful to man, and the supply of water, not only for agriculture, but also for mining and all other purposes, falls below the demands made upon it. In such localities flowing water has a great value, for without it many industries are impossible. Experience has shown that in the western part of the United States, over an area a little less than two-fifths of the whole extent of the country, there are great bodies of fertile land enjoying a genial climate, and in every way adapted to the support of a large population, except in the one particular of water-supply. By utilizing the water available, portions of this rich land can be rendered valnable. In other words, the laud-values rest directly upon the prospects of a continuous artificial water-supply. The same is true of many mineral lands, which require for hydraulic mining, or for the supply of concentrating-works, stanip-mills, etc., a certain water-supply, and are impaired in value if this supply is inadequate or irregular. The pressure of this need upon the mining industry is not so widespread, or in the first instance so severe as upon agriculture; but as different regions become more thickly settled, and the two industries compete for a water-supply not sufficient for both, it, is probable that the miner will suffer. But he can snspend operations with less inconvenience than the farmer. Agricuitural land, if the watersupply is not continuous, becomes a desert; on the other hand, the profit of mining is greatly enhanced by the presence of agricultural

Jan 1, 1892

By H. J. Hand

Statistical methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor, 1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.—Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such p1ants. Many Useful Statistical Devices Available.—Many statistical methods of attack are available for the analysis of plant data. It is the object of

Jan 1, 1938

By C. A. Mitke

In the Southwest, mcchanical ventilation of metal mines has been receiving consideration for many years. The United Verde Copper Co., in Jerome, has used large mine fans for ventilation and fire-fighting purposes for at lcast 15 years, while the Copper Qucen Branch of the Phelps Dodge Corpn. commenced installing mechanical ventilation in its various divisions 10 years ago.' Since then, with few exceptions, every large mine in this part of the country has installed and put in operation a mechanical ventilating system. The properties of some of these companies consist of from two to six divisions, or separate mines, each of which requires an independent ventilating system. In other words, thirteen copper mining companies, with an aggregate tonnage, when operating at capacity, of approximately 50,000 tons a day, have installed mechanical ventilating systems in their mines. All these mines are within a radius of approximately 200 miles, which constitutes the largest copper-producing area in the world. The capacities of mechanical ventilating installations in these mines range from 100,000 to 300,000 cu. ft. of air per minute, depending on the size of the mine, character of the workings, tonnage produced, etc. The latter varies from 300 to 20,000 tons per day. The mines include both high- and low-grade deposits, the greatest depth of the former, at present, being approximately 2500 ft.; and of the latter, 1200 ft. The volumes of air at present being coursed through the mines are from 60,000 up to 225,000 cu. ft. of air per minute,which, in their relation to the undcrground working force, range from 200 to 800 cu. ft. of air per man, per minute. While not to be taken as criteria, these figures are indicative of the character of the ventilation furnished.

Jan 1, 1923

By G. St. J. Perrot, S. P. Kinney

Consumers of metallurgical coke are agreed that the quality of their fuel plays an important part in the performance of the furnace. Less unanimous agreement is evident when the properties of a desirable coke are discussed or when consideration is made of suitable testing methods by which the worth of a coke for metallurgical purposes may be determined quantitatively. Much has been written of the importance of combustibility as a factor in determining the performance of coke in the blast furnace and it is generally believed that cokes vary widely in this respect. The usual operating data of the furnace afford little evidence as to the combustibility of the fuel. As a part of a general investigation of the properties of metallurgical coke, the Bureau of Mines has explored the hearth combustion zone in a number of blast furnaces by means of water-cooled gas sampling tubes driven into the hearth through the tuyeres. The attempt has been made to determine the difference in combustibility of cokes varying widely in physical properties. Data have also been obtained in an experimental combustion furnace at the Bureau laboratories in Pittsburgh. This paper gives the results of experiments, made at eleven blast furnaces, in which the composition of the gases was determined at various points in the hearth in the plane of the tuyeres. Further work is in progress in which the zone above the tuyeres will be explored. Factors Affecting Coke Combustibility Brassertl has defined combustibility as the rate of progression of combustion, or, in other words, the speed at which the carbon molecules

Jan 1, 1923

By F. B. Plummer, R. B. Newcome

The practice of introducing acid into oil wells to increase production of oil and gas has been in use since 1894, when it was first used in the Pennsylvania oil fields30.‡ It is only since 1928 that it has been used to any extent in the Mid-Continent18. The process has proved successful in increasing production, at least temporarily, in depleted oil fields where the producing formation is highly calcareous and where water drive is not too pronounced. In the Zwolle field in Louisiana, where the producing horizon is a chalk, increases of 100 per cent have been recorded25. In north-central Texas, where the oil is produced from the Marble Falls limestone, equally pronounced increases have resulted3. The production also in some fields yielding oil from quartz sand cemented with calcitc has been benefited. The evidence of actual increase in total recovery of oil, however, has been questioned by some engineers18. It has been pointed out that the results of the treatment of a well in a now district, where the process has never been tried out, can never be predicted with certainty, since other factors besides percentage of calcareous content of the oil sand play a large part in determining the success of the method. Numerous articles have been published on acid treatment and on the effects of acid on limestone1-35, yet very little has been written concerning experimental work on the actual effect of acid on capillary pores and larger oil-coated voids of oil sands. This is due partly to difficulties in duplicating field conditions in a laboratory and partly to the fact that the process has been carried out largely by contracting companies that have been unwilling to publish details of their results for fear of loss of business to competitors. The authors, using equipment developed to measure the radial permeability of oil-sand cores2', have developed a method of investigating the results of acid treatment which has enabled them to test numerous cores and to study in some detail the action of acid on the different types of rocks, particularly fine-grained rocks.

Jan 1, 1936

By E. L. Spain Jr. N. A. Rose

This study was undertaken primarily to determine the reasons for certain variations in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates in some cases exhibited marked differences in specific gravity. crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents. Introduction When it is stated that the aggregate from one point is inferior to that from another, it must not be construed to mean that the gravel is unfit for use. The classification upon which such aggregate ratings are based is largely arbitrary, thus inferiority or superiority is merely relative. Samples of gravel were selected from stockpiles at the dams of the Tennessee Valley Authority under construction, from the stockpiles of private companies along the river, and from samples taken by the gravel-exploration barge of the T. V. A. One hundred or more gravels of each size studied were selected at random by taking small handfuls while walking around the piles. These were separated according to the different mineral or rock constituents present, and the percentage of each constituent was obtained by counting. At least three such samples were taken from each size, and all checked with one another within a few per cent. The results were then averaged. In order to check on the accuracy of such sampling, a whole sample was taken from one point after the gravel was thoroughly mixed. The two methods gave approximately identical results. Sources and Types of Materials The sources of gravel found in the Tennessee River are numerous and varied. The river itself traverses several geologic provinces, each

Jan 1, 1938

By W.C Ellis, Earle E. Schumacher

Nonferrous alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,' nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

By Gerhard Derge

The extension of metallurgical control of steelmaking processes has always made it desirable to have some quick method for determining the oxygen content of molten steel. To meet the practical demands of the steel industry, this method must also be simple enough so that the sampling can be done by the regular furnace crew. This requirement was kept in mind continually in the work to be described. An oxygen value is required for proper control, whether it be of a rimming steel or of a fully killed steel. However, two factors have discouraged the development of such direct methods: i. The reaction C + FeO Fe + CO is rapid enough to make the correct sampling Of the bath a difficult problem. The most generally accepted means of circumventing this difficulty have been the aluminum-killed bomb test of McCutcheon and Rautiol and the aluminum-killed spoon test of Herty.2 The theory of these tests is that all of the oxygen in the iron is converted to Al2O3, which can then be determined by chemical methods. Even when simplified so that the analysis is made by a measurement of turbidity, this method is too slow to be used in routine control. Furthermore, the results obtained have never been entirely satisfactory, and some of the reasons for this will be discussed later in this paper. z. The ordinary chemical methods of analysis for oxygen in steel are not reliable. The only analysis that seems to possess sufficient dependability to be of value is vacuum fusion,3 and the apparatus and technique developed for this have been too complex and slow for routine work. Indirect Methods Indirect methods of estimating the oxygen have been resorted to in mill practice. Generally these depend upon the chemical equilibria involved. The oxygen in the bath is related to other components in the slag or metal that can be analyzed the readily. These methods have many difficulties in common. Steelmaking processes involve a complicated set of interrelated reactions, all of which tend to approach equilibrium at varying rates. The degree to which any particular equilibrium is approached is not well established. Moreover, a proper use of theoretical equilibrium constants requires a more extensive knowledge of the activities of the con- than we now have. This is well illustrated by the irregularities observed when trying to determine the oxygen in the metal by its ratio to the iron oxide in the slag. Equiliblium relations may be used mole readily if they are evaluated by plant experience, but the extent of approach to equilibrium remains an undetermined variable and lack of an entirely satisfactory mean, of determining oxygen for the calibration is felt keenly, For example, the statistical analysis of the relation between carbon and oxygen4.6 illustrates that even iia a single plant wide variations exist under llormal conditions of operation. Never. theless, this is one of the best methods now

Jan 1, 1943

By Donald E. Ackerman, Norman B. Pilling

The solubilities of a series of experimental alloys covering the range 0 to 100 per cent. Ni, 0 to 30 per cent. Cr have been studied under conditions of complete submersion in several fully aerated acid solutions, and in solutions containing sulfurous acid. In nonoxidizing, hydrogen-discharging acids, if the nickel content is below a certain critical amount, chromium increases the rate of solution and nickel decreases this rate; this critical content of nickel is about 13 per cent. Alloys containing more than this corrode at a constant minimum rate independent of iron, nickel or chromium contents. Austenitic chrome-nickel steels may thus have a resistance to these acids equal to that of nickel-chromium alloys. In nitric acid and in unaerated sulfurous acid rather sharp limits of attack occur which are principally dependent on chromium content. In the former the limit of attack is not related to a particular chromium content but varies continuously with acid concentration. The action of sulfurous acid on these alloys is highly dependent on the presence of small amounts of other substances in solution, and many sulfurous acid mixtures rapidly attack alloys to which the pure acid is wholly inert. The observed effects are not compatible with Tammann's theory relating corrosion resistance to lattice structure but are believed to be concordant with current views of the electrochemical nature of corrosion. Introduction The discovery, development and engineering application of iron alloys resistant to corrosion may well claim a place among the important developments in metallurgy of the past two decades. The varied demands of industry coupled with the skill of the metallurgist have resulted in the production of an extensive group of steels and alloys ranging from the now familiar "stainless " chromium steels of the kitchen to special alloys of great chemical complexity for particular, exacting needs. Any adequate description of the important properties of these-— physical, chemical and economic—would be a formidable undertaking.

Jan 1, 1929

By James E. Little

Of the several extensive deposits of brown iron-ore in Cuba, including those of Mayari and Moa, that of Mayari was the first to be systematically explored, and was selected as the scene of the first operations in the development of this class of ore. Construction-work, begun in the spring of 1907, involved the building of 16 miles of stantlard-gauge railroad and two large double-track inelines, the installation of milling-machinery, a nodulizing-plant, power-plant, shops and shipping-facilities, and the dredging of an extensive basin for deep-draught vessels. Unusual weather-conditions delayed the completion of portions of this work so that the entire plant was not in operation until December, 1900.

Jan 1, 1912