Search Documents

By Charles H. Fulton

THE Engineering Education group began its sessions Tuesday morning, Feb. 16, as a Committee and wound up the day as the Institute's fifth " Division." C.II. Fulton presided. The first paper for discussion was entitled "Teaching Management in Engineering Schools,"' by Eugene McAuliffe, president of the Union Pacific Coal Co., space for which may be found later in these pages. In it, Mr. McAuliffe argued that an engineering student should be taught the knowledge of men, much as a medical school teaches surgery. He then went on to indicate, out of the wealth of his administrative experience, the problems an executive needs to be equipped to handle, and said that every student engineer should look on himself as a potential manager.

Jan 1, 1932

By AIME AIME

APPARENTLY unperturbed by any misgiving as to ill luck connected with the mystic number thirteen -for there were exactly that number of Directors on deck-the Board held two sessions on Tuesday, Feb. 21. , . Between the executive session at 5:15 p. m. and the general session at 8:30 p. m., 28 Section and Division delegates were wests of the Directors at dinner. Committee chair- " men and past officers brought the attendance to 75. Messrs. McAuliffe, Merica, Mudd and Tally had expressed their intention to be at the Directors' meeting, but each was prevented unavoidably at the last minute. At the executive session of the Board, J. V. W. Reynders was unanimously chosen to fill the unexpired term of Dr. Becket as Director: and Eugene McAuliffe in like " manner was selected to become Vice-president to fill the vacancy created hy Dr. Becket's assumption of the Presidency. Upon nomination of President Becket the following Executive Committee was appointed: Frederick M. Becket, chairman; Howard N. Eavenson, H. A. Guess, J. V. W. Reynders and William Wraith; and the Finance Committee was appointed as follows: Henry Krumb, chairman; Paul D. Merica and H. G. Moulton. Karl Eilers was reelected Treasurer and A. B. Parsons was re- elected Secretary to serve for the ensuing year, whereupon the executive session was adjourned.

Jan 1, 1933

Jan 1, 1910

By A. D. LeClaire

This paper claims to provide a description of diffusion processes in solids which is said to be a reformulation of Fick's Laws and therefore, presumably, is supposed to be as general as those laws. In fact, it appears to provide no more than an atomic model of a rather restricted type leading even to results in conflict with experiment. The restriction lies in the assumption, carried throughout the paper, that even in a chemical gradient the jump frequency i of an atom of species i is a function only of the composition on the plane from which it jumps, i.e., ?i = ?i(cl, c2 ...). This means that atom jumps in opposite directions from a site would occur with equal probability. There would then be no tendency for atoms to migrate preferentially in one direction along the gradient, so the model is incapable of accommodating the well established phenomenon of atom drift in a chemical gradient.10-" A more general model that does not suffer this difficulty was discussed in a paper13 I wrote in 1958, and the results therein already contain as a special case those given by Dr. DeHoff. The simplest sufficiently general assumption is to suppose that ?i is a function ?i(a1 a2,...; wl, w2, ..-) of the concentration aj and ? ?j at the site from which and to which, respectively, a jump is made. Any such function can always be expressed as a function of the sum and difference of its arguments. Thus d is the jump distance and g a geometrical constant. Obviously this is zero, i.e., no drift, if ??ri/??j = 0. X is written in this form, revealing two components of the total drift, because it can be shown that only the second component, depending on ??'i/???(?j -aj), actually contributes to the net diffusion flux Ji. This component can be shown,13 by a straightforward ther-modynamic transcription, to be responsible for the so called "thermodynamic factor" in the Darken approximation for a chemical diffusion coefficient is the activity coefficient of i. Because the jump rate ?i in DeHoff's approximation has no dependence on the concentration gradient it does not seem possible to derive the Darken equation from his Eq. [6] without the further rather arbitrary assumption that ?i = const ri. It is to be noted too that the author's derivation of Eq. [12] is only valid when ?i is in fact a function only of the cj at the plane from which the atom jumps—for only then is ci?i a unique function of position and therefore of A. Author's Reply R. T. DeHoff I am indebted to Dr. LeClaire for his penetrating discussion of my paper, "A Reformulation of Fick's First Law". I concede that it does appear initially that the relationship presented in my paper could be derived from the detail atomic model of random walk and atom drift presented in Dr. LeClaire's approach. However, there are some important differences in concept and viewpoint which deserve further amplification. Dr. LeClaire's description is penetrating, detailed, and fundamental. His approach describes an extremely complex phenomenon, the displacement of atoms in a multicomponent gradient, at a sophisticated level. For precisely these reasons, his analysis has not proved to be useful for experimental studies that have practical objectives. For example, in order to obtain the information required to complete the analysis of the jump frequency distribution in a ternary system, the following series of experiments would, I believe, be required: 1) chemical (gradient) experiments, covering the composition range;

Jan 1, 1970

R,. P. JaRvis,* El Oro, Estado de México, México.—The practical problem raised by Mr. Wisser—that is, the determination of the lower limit of ore deposition, below which it is useless to look for ore shoots—is one of the most important in economic geology. He asks: "Can we learn to determine the position of such a line?" For individual districts, yes; but its determination has always been by empirical methods; that is by actually exploring the veins to such depths that the values drop below the economic limits. Usually the signs are plain enough that values have been bottomed without confirmation by the chemist or assayer. Most veins, when approaching their limit, begin to split into branches or stringers; the vein matter itself undergoes a change from "lively looking" rock to one that is dull and unpromising, the quartz, instead of having segregated into clean vein matter, has simply spread itself into the country rock, rendering this more siliceous but no richer—these, together with inclusions of the country rock in the vein, are all positive indications of the limit. Mr. Wisser seems disposed not to accept the law of cause and effect, which he calls "empiricism." He says: "Empiricism embodies an assumption perhaps not evident at first glance. It is this: that like effects spring from like causes and therefore necessarily have a common meaning." There can be no doubt as to the validity of this law, since it is the foundation stone upon which are built all inductive sciences, including economic geology. When demonstrable, proved facts become confused with inferences, as they seem to be generally in the paper under examination, no sound conclusions can be reached. Mr. Wisser has failed to give sufficient data covering the two vein systems which he cites as examples. Presumably they are situated in the Pachuca District of Mexico, but not everybody is familiar with the vein systems there in spite of the fact that it is world famous as a silver producer. Are these two systems separated some distance horizontally from one another and how far? He has given no estimate of the amount and kind of rock that has been eroded from over the present veins. His description of the two systems appears on page 100, beginning: "1. East-west veins," and ends on page 101, "they would lack spaces there in which to deposit." On page 101, with the paragraph beginning "On the other hand," he gives a picture of what he believes takes place in class 2 veins. The sum of this seems to be, according to Mr. Wisser's observations, that, in the east-west veins, class 1, there has been an invasion of an "altering solution," which I judge has been responsible for the formation of extensive "alteration haloes"; that these alteration solutions have followed along pre-existing fractures or fissures; and that after these alteration solutions finished their work the mineralizing solutions deposited the vein matter and metallic values. Mr. Wisser does not specify clearly what the "alteration haloes" consist of; in other words, what change the original rock has suffered, whether oxidizing, carbonating, or sulphidizing. If they came from depth they could not be oxidizing or carbonating, and in this case it is a bit

Jan 1, 1941

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.)

Jan 1, 1951

By H. H. Kellogg

0. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.)

Jan 1, 1951

R,. P. JaRvis,* El Oro, Estado de México, México.—The practical problem raised by Mr. Wisser—that is, the determination of the lower limit of ore deposition, below which it is useless to look for ore shoots—is one of the most important in economic geology. He asks: "Can we learn to determine the position of such a line?" For individual districts, yes; but its determination has always been by empirical methods; that is by actually exploring the veins to such depths that the values drop below the economic limits. Usually the signs are plain enough that values have been bottomed without confirmation by the chemist or assayer. Most veins, when approaching their limit, begin to split into branches or stringers; the vein matter itself undergoes a change from "lively looking" rock to one that is dull and unpromising, the quartz, instead of having segregated into clean vein matter, has simply spread itself into the country rock, rendering this more siliceous but no richer—these, together with inclusions of the country rock in the vein, are all positive indications of the limit. Mr. Wisser seems disposed not to accept the law of cause and effect, which he calls "empiricism." He says: "Empiricism embodies an assumption perhaps not evident at first glance. It is this: that like effects spring from like causes and therefore necessarily have a common meaning." There can be no doubt as to the validity of this law, since it is the foundation stone upon which are built all inductive sciences, including economic geology. When demonstrable, proved facts become confused with inferences, as they seem to be generally in the paper under examination, no sound conclusions can be reached. Mr. Wisser has failed to give sufficient data covering the two vein systems which he cites as examples. Presumably they are situated in the Pachuca District of Mexico, but not everybody is familiar with the vein systems there in spite of the fact that it is world famous as a silver producer. Are these two systems separated some distance horizontally from one another and how far? He has given no estimate of the amount and kind of rock that has been eroded from over the present veins. His description of the two systems appears on page 100, beginning: "1. East-west veins," and ends on page 101, "they would lack spaces there in which to deposit." On page 101, with the paragraph beginning "On the other hand," he gives a picture of what he believes takes place in class 2 veins. The sum of this seems to be, according to Mr. Wisser's observations, that, in the east-west veins, class 1, there has been an invasion of an "altering solution," which I judge has been responsible for the formation of extensive "alteration haloes"; that these alteration solutions have followed along pre-existing fractures or fissures; and that after these alteration solutions finished their work the mineralizing solutions deposited the vein matter and metallic values. Mr. Wisser does not specify clearly what the "alteration haloes" consist of; in other words, what change the original rock has suffered, whether oxidizing, carbonating, or sulphidizing. If they came from depth they could not be oxidizing or carbonating, and in this case it is a bit

Jan 1, 1941

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.) O F. A. Forward, C. S. Samis, and V. Kudryk: Trans. Canadian Institute of Mining and Metallurgy. (1948) 151 (Bull. 434) 350-355.

Jan 1, 1951

By H. F. Mills

The Iron King mine is I2 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped unti1 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of I40 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Dcnn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular. no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 80 ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 920-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1949

By W. T. Olsen, R. Ulcer

WHEN a liquid alloy freezes, the solid first formed usually differs widely in chemical composition from that last formed, so that there is segregation in the alloy as cast. For example in the copper-nickel system (fig. 1) the first solid formed from a liquid containing 55 atomic pct Cu may contain as little as 38 pct Cu, while the last must contain well over 55 pct. Three factors may act to decrease segregation from the maximum possible. 1. Diffusion in the cooling solid tends to make the phase homogeneous, decreasing segregation. This may be important at slow rates of cooling. 2. Segregation is impossible without diffusion in the liquid. At extremely rapid rates of cooling there may not be enough time to allow maximum segregation. 3. Supercooling delays nucleation to temperatures well below the liquidus thereby decreasing segregation. Hence the first nucleus in the copper-nickel system may contain well over 38 pct Cu. At sufficient supercooling the first nucleus may form below the solidus, in which case there is no reason to expect any segregation whatever. From these considerations, we could predict that at sufficiently low rates of cooling the alloy would be unsegregated because of factor 1 and at sufficiently high rates of cooling there should also be no segregation because of factors 2 and 3. Considerable segregation should occur only at intermediate rates of cooling. We have demonstrated experimentally that segregation can be completely suppressed by rapid rates of cooling. For the alloys studied, however, these rates are too great to be attained in any commercial practice. An alloy of 55 atomic pct Cu, 45 atomic pct Ni was frozen by cooling at varying rates. The degree of segregation in the solid was determined by X-ray diffraction photographs. Slow rates were obtained by slowly cooling the furnace containing the liquid alloy; fast rates by pouring or ejecting droplets of the alloy into water or iced sodium hydroxide solutions. The cooling rate of the droplets can be cal-culated from their dimensions by assuming reason- able values of thermal conductivity.' The experi-ments were repeated with an alloy of 16.5 pct Cu and 83.5 pct Au. A single experiment also showed a 50 atomic pct Bi-Sb alloy had no segregation at the most rapid quench. The position of back-reflection X-ray diffraction lines is a highly sensitive function of the lattice constant, which in turn depends on the chemical composition of the phase. A phase of varying composition will give broad diffraction lines. By measuring the edges of these lines and making suitable corrections for intrinsic line width, it is possible to determine the range of lattice constants represented. These can be converted to chemical compositions from a lattice constant vs. composition curve. Results are shown in table I. In the copper-nickel system the greatest segregation is found at the slowest cooling rates, where the lowest percentage of copper theoretically possible is found. In the copper-gold system, on the other hand, the degree of segregation is decidedly less at the slowest rates of cooling, being greatest at 11,100°C per sec. At no rate is the theoretically lowest percentage of copper (12 pct) found. At the rates of cooling found in sand and die castings the degree of segregation is large and depends little on the rate of cooling. Acknowledgment Most of the material in this paper is abstracted from a thesis presented by William T. Olsen, Jr. in 1948 in partial fulfillment of the requirements for the degree of Master of Science at the University of California.

Jan 1, 1951

By Howard Martens

HARDNESS behavior of commercial titanium alloys following various heat treating processes has been studied for some time. However, the hardness of such alloys following a definite measured cooling rate from the single phase region has not been reported. Therefore, a series of experiments was conducted on the three alloys: 150A, 130A, and 130B. The manufacturers gave the following compositions for these alloys: Ti 150A: 0.045 pct C, 0.069 pctN, 1.32 pct Fe, and 2.68 pct Cr; RC 130A: 0.13 pct C, and 7.9 pct Mn: RC 130B: 0.11 pct C, 3.5 pct Mn, and 3.2 pct Al. A method similar to that described by Greninger was used, and the cooling rate varied from 6" to 9200°F per sec. The cooling curves were recorded on a Speedomax or a recording oscillograph, and the hardness was measured on a Tukon hardness tester using a Knoop indentor with a 500 g load. The curves of Fig. 1 show the variation of the Knoop hardness with the cooling rate for these three alloys. The alloys 150A and 130B behave in a similar manner, as shown by the curves. In neither of these alloys was it; possible to retain the high temperature ß phases, even by the most rapid cooling rate. The slow cooling rates produced a typical ß structure in these two alloys. As the cooling was increased, these phalses became more finely dispersed and the hardness increased. This increase in hardness with cooling rate continued for the 150A alloy until a rate of approximately 1000°F per sec was reached. At this cooling rate, the structure showed the result of the dif-fusionless transformation of the ß solid solution to the supersaturated a solid solution which is referred as a'. At higher cooling rates, the structure showed no change and the hardness showed no great change, as indicated by the dotted portion of the curve in Fig. 1. The increase in hardness with cooling rate for the 130B alloy continued until a rate of approximately 300°F per sec was reached. At this rate the structure was produced and the maximum hardness was reached. Higher cooling rates caused no marked changes in hardness or structure. The alloy 130A behaved in a different manner, as shown by the curve of Fig. 1. The structure produced by the slow cooling rates was a typical a+ß structure, which became finely dispersed as the cooling rate increased. The hardness increased with cooling rate and reached a maximum at approximately 120°F per sec. At this maximum hardness, the structure showed the result of the decomposition of the ß phase into the ß + phase structure. As the cooling rate was increased, smaller amounts of the at phase were formed and the alloy became softer. For cooling rates of 3000°F per sec and above, the high temperature ß phase was retained and the hardness of the alloy did not change markedly. Acknowledgment This paper presents the results of one phase of research carried out at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-0rd 18, sponsored by the Dept. of the Army, Ordnance Corps.

Jan 1, 1957

By H. F. Mills

THE Iron King mine is 12 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped until 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of 140 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Denn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular, no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 8o ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 92o-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1947

By H. F. Mills

The Iron King mine is I2 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped unti1 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of I40 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Dcnn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular. no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 80 ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 920-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1949

By Erwin Pink

It has been pointed out in a previous publication' that, for a given strain rate, serrated yielding can be observed only at certain test temperatures. Fig. 1 shows the results obtained for polycrystalline and re-crystallized tantalum, Va group in the periodic table of elements, where serrations in the course of deformation match the decrease of total elongation. However, there was no evidence of repeated yielding when testing molybdenum or tungsten, VIa group, at similar conditions, i.e., annealed and air-cooled samples (serrations have been found in quenched tungsten2). The reason for the observed serrations in the stress-strain curve are dissolved impurities on interstitial sites of the lattice. Of importance is the concentration of oxygen, carbon, and nitrogen, which are in random solution. Two methods to calculate the limiting concentrations for serrated yielding have been evaluated and applied with more or less success in estimating the role of carbon and nitrogen in mild steel.3 J. Friedel4 has given two equations, which determine the upper and lower strain rates i for the appearance of serrations at a certain test temperature: W denotes the binding energy of the interstitial atom, -1 ev for refractory metals;5 e' the portion of continuous strain in the discontinuous stress-strain curve, measured as -3x10-3; b the Burgers vector, c the concentration, see Table 11, in atom fractions; p the dislocation density, -2 X l09 per cm2 at an average stress ?, -15 kp per mm2 at medium strain. k stands for the Boltzmann constant, T for the absolute temperature, and D for the diffusion coefficient. Table I. Eq. [1], for a given strain rate, determines the minimum temperature, and [2] the maximum temperature, below or above which no "dynamic strain-aging" can occur. According to the calculation, which uses the given quantities, serrations should only be observed within the cross-hatched temperature regions in Fig. 1, and this is in good agreement with the experiment. The effect of varying impurity concentrations is indicated schematically in Fig. 2: only Eq. [I] is affected. Setting Eq. [I] equal to [2], one can calculate the limiting concentration cmin which first causes serrations. The second method uses the aging condition by Cottrell and Bilby6,7 \£i/ \ n. a / where n(t) is the number of impurity atoms, which segregate at a dislocation line of 1 cm length after the time t (t in our case is the time between "repeated yield drops" in the serrated curve, or, the time until the above mentioned strain E' is obtained, i.e., -1 sec for medium intensity or serrations). no is the number of impurity atoms in 1 cm3 and A = Qb4ep[(1 + v)/(l - v)], derived from equations given in Ref. 7. p is the shear modulus, 18,800 kp per mm2 for tantalum, 12,200 for molybdenum, AE the tetragonal distortion caused by interstitial impurities in a bcc lattice (approximately 0.4 for both tantalum and molybdenum) and v Poisson's ratio (0.35 for tantalum, 0.30 for molybdenum). From Eq. [3], combined with the condition for a pronounced yield drop as formulated by cottrel16 (at least one impurity atom segregated at the unit length of a dislocation), again a no min, and hence the concentration Cmin can be calculated.

Jan 1, 1970

By A. J. May

THE Star shaft is near the north boundary of the group of mining claims belonging to the Ground Hog Unit of the American Smelting and Refining Co., near Vanadium, N. Mex. The shaft bins and surface plant are served by a siding from the Atchison, Topeka and Santa Fe railroad, and this factor of railroad transportation influenced the choice of site. This paper describes the shaft sinking only, and does not cover the surface plant or other parts of the mine or its equipment. Experience with this shaft seems of interest because of the mechanical mucking, good rate of progress, and the costs obtained at the present level of labor and material costs. The shaft has four compartments, as shown in fig. 1. Equipment: Riddell Mucker: The mucking was done by a clamshell bucket and a Riddell mucker, which, as in other shafts sunk with this machine, consisted of a carriage mounted on axles with double flanged wheels that traveled back and forth on a swinging track, parallel to the long axis of the shaft (fig. 2 to 6). Three air motors were mounted on the carriage; one hoisted the clam, one operated the bucket opening and closing device, and the third moved the carriage along the track. The carriage was designed with guide shoes and could be hoisted to the surface in either skip compartment without trouble (fig. 4). During blasting operations the clam was tied on the rails and the carriage was hoisted up a few sets to protect it from flying rock. No attempt was made to hoist the carriage and clam together lest the clam catch in the timbers. The track on which the carriage operated was built of extra heavy 6 in. pipe with 1x2 in. strap welded on top for rails. A 1/2x4 in. angle was welded on the bottom of the 6 in. pipe with a 1 in. round rod welded in the angle for a filler and additional strength. The end or cross pieces of the track which kept the track to gauge, were also made of reinforced, heavy 6 in. pipe and were bolted to the long members on which the carriage traveled (fig. 2 and 3). This section of track was used, instead of heavy railroad rails, for two reasons: (1) this section would bend before it snapped and was much safer for the men in the bottom; and (2) it was a better blasting shield, and protected the timbers better, in fact, only five wall plates were broken by blasting in 1926 ft of shaft, although 150 to 225 lb of 40 pct powder was loaded per round, depending on the ground conditions. The swinging track was supported by four 5/s in. hoisting cables anchored to the end plates. There were also four safety cables fastened two to three sets above the carriage, which would catch the carriage if one of the supporting cables should fail for any reason (fig. 7). Clamshell Buckets: Two clams were used, each of 3/s yard capacity, both manufactured by Blaw Knox, Nos. 662 and 663. The No. 663 clam was 4 in. wider and 5 in. shorter than the No. 662, but seemed to dig and load more satisfactorily. It was easier to hoist and lower when it came up for repair. It did not turn over as easily, had less spill

Jan 1, 1950

It has been established that molybdenum sesquisulphide, not molybdenite, is in equilibrium with molybdenum metal and sulphur vapor in the vicinity of 1100°C. The S2 pressure for this system has been obtained using the Knudsen orifice method and the standard free energy for the dissociation of S2. THIS work was undertaken to help in determining the thermodynamic properties of the molybdenum sulphide which is in equilibrium with metallic molybdenum and sulphur vapor in the temperature range 1025" to 1150°C. From the results of MontoroL and of Parravano and Malquori' molybdenite would be expected to be in equilibrium with molybdenum metal, while the results of Guichard indicate that a lower sulphide must be in equilibrium with the metal. Thus it was concluded that the problem warranted reconsideration, especially in view of the suspiciously low temperature independent term for the standard free-energy function for the reaction MoS² Mo + S,. The reaction was calculated and duly noted as being low by Richardson and Jeffes,' using the data of Parravano and Malquori.' Experimental Method The general method used in this investigation is that of the Knudsen orifice method for the determination of equilibrium pressure. The apparatus and technique are similar to those described for the determination of the vapor pressure of silver.% owever, a closed-end McDanel tube instead of fused silica was used to maintain the vacuum, a molybdenum effusion cell with a replaceable lid was employed instead of a silica cell, and a titanium getter maintained at run temperature was used to assure that no oxidation of the molybdenum or molybdenum sulphide was taking place. All runs were made at a residual pressure less than 10-5 mm Hg. The data are given in Table I. Runs 1 through 13 were obtained using molybdenite, analyzed 98.5 pct, from the Molybdenum Corp. of America. The remaining runs were done with a sample from the Climax Molybdenum Corp. which was their grade No. 3 and analyzed 59.87 pct Mo. The weight loss of the cell during heating up and cooling down was subtracted from the total weight loss of the cell during the run. Also, when the tem- perature was changed, the Knudsen cell was placed in the vacuum chamber and heated at temperature for several hours in order to allow the sulphide and the metal to adjust their compositions to the equilibrium values, to desorb or adsorb gases into or from the molybdenum cell itself, and to desorb any water from the molybdenum sulphide or molybdenum powder inside the cell. Water may have been adsorbed inside the cell because, after each run, the top of the cell was removed and the material in the cell was stirred to insure that a layer of molybdenum metal would not build up and obstruct the passage of sulphur vapor into the gas phase. It was established that the molybdenum cell alone decreased in weight an inappreciable amount when heated at the highest run temperature for long periods of time. There are two questions to be answered before the data in Table I can be used to calculate thermodynamic functions: 1—Which molybdenum sulphide is in equilibrium with molybdenum metal and sulphur vapor? 2—What sulphur species are present in the vapor phase? It can be assumed safely that no molybdenum is vaporized, since its vapor pressure is almost negligible at these temperatures. It will be shown subsequently that no sulphide of molybdenum is volatile. Question 1 was answered in the following way: The especially purified molybdenite, obtained from the suppliers mentioned previously, was charged

Jan 1, 1956

By W. T. Turrall, M. J. Cook

A discussion of modern developments in beneficiation of fine sizes of anthracite, this paper includes a description of the plant flowsheet, an analysis of operating results, and a summary of fundamentals of mineral separation relative to plant operation. DURING the past several years Lehigh Naviga-tion Coal Co. has installed equipment at Tamaqua and Lansford collieries for cleaning and sizing No. 4 buckwheat —3/32 + 3/64 in. and for recovering and cleaning flotation coal —20 + 200 mesh at Tamaqua colliery. Papers describing some of these installations have been presented to AIME. At Coaldale colliery, however, methods used to clean fine coal were inadequate and inefficient. Management decided upon a thorough investigation of all existing processes before building a plant to treat the combined three sizes mentioned. Investigation, carried out on company property and at other plants, entailed a study of hydrotators, hydroclassifiers, tables, spirals, flotation machines, methods of screening, and methods of dewatering. On the basis of this investigation a flowsheet was designed which necessarily excluded many processes in use, and the writers wish to emphasize that no criticism is implied by omission of processes or machines. A determining factor in selection of many machines was the policy of standardizing equipment wherever possible. Flowsheet and Operational Data The first principle to be considered in designing of any plant is efficiency of cleaning as related to laws of classification. Beneficiation of coal may be described as separation of two materials having different specific gravities. Although there is an inherent ash content even in the purest coal which slightly affects its specific gravity, it is recognized that many particles are true middlings. The percentage of these particles allowable in the final product depends upon the ultimate ash, or specifications of the consumer. Richards in his study of free settling and hindered settling classification' determined that particles of equal size and different specific gravities had unequal settling velocities. He also determined a definite size relationship for equal settling velocities with free settling and hindered settling conditions. Considering the design of machines used to clean No. 4 and No. 5 buckwheat, it may be assumed that both free settling and hindered settling conditions exist and that ratio of size for practical operations is between the established values. The essential factor is that the more efficiently and closely sized the feed is maintained, the more nearly perfect the resulting separation. Flowsheet design was governed primarily by factors related to the 1200 to 1500 tons per hr feed to the main plant. It should be stressed that because of the many sources of supply from mine and stripping, the physical characteristics of this feed varied considerably. The most significant influence was varying percentage of fines, necessitating that all machines be capable of operating under maximum peak load during periods of surge. Since cleaning practice is a wet process, about 9000 gal per min containing 14 to 15 pct solids, or 350 tons per hr, must be treated. This slurry contained all the fines, or —3/32 in., but also percentages of oversize, up to 1 % in., dependent on spills or breaks in screen jackets, a not uncommon occurrence in preparation plant practice. The flowsheet developed is shown in Fig. 1. Circled numbers represent points of sampling. Table I gives operational data including size, ash by size, composite ash, rate of flow in gallons per minute, percent solids dry weight, and average tons of solids per hour. It should be noted that these results are subject to human error in sampling practice. Detailed information reported is a representative evaluation of plant operation.

Jan 1, 1954

By Robert A. Rapp, Jan E. Verfurth

From the measurement of internal-oxidation band widths in Ag-In and Cu-A1 alloys, products for the solubility No and the diffusivity Do of oxygen in silver and apparent NODo products in copper have been obtained over a range of temperature. The NODO products for silver are in agreement with the product of the individually determined No and Do values of Eichenauer and Müller. Although interstitial diffusion of oxygen in silver is expected, the temperature-independent factor Do of the diffusion coefficient does not agree well with the theory of Wert and Zener. For Cu-A1 alloys internal oxidation does not follow the expression derived for ideal kinetics, since the apparent NODo product calculated from internal-oxidation measurements is a function of the alloy content in the specimen. Thus, unequivocal values for No or DO or even the product NODO in copper are not available from the literature. RELIABLE values for the saturation solubility NO and diffusivity DO of oxygen in fcc metals are lacking and difficult to determine, partially because internal-friction measurements are not applicable. Permeability experiments and Sieverts7-type adsorption -desorption methods3 have met with difficulty; however, Eichenauer and Müller4 have recently reported on the solubility and diffusivity of oxygen in silver as determined by the latter technique . Rhines, Johnson, and Anderson,5 and independently Meijering and Druyvesteyn,' introduced the possibility of deriving values for the product NODO in a metal from measurements of the widths of internal-oxidation zones (subscales) formed during the internal oxidation of alloys. In addition to these authors, several other investigators7-9 have made such measurements in various silver and copper alloys at various temperatures, mostly using me- chanically polished specimen surfaces. The purpose of this investigation was to determine over a range of temperature the calculated products NODO in silver and copper from systematic measurements of the widths of internally oxidized zones in Ag-In and Cu-A1 alloys, using specimens with electro-etched surfaces. Consider the internal oxidation of a dilute solid-solution alloy in which the base metal is not oxidized. If diffusion of oxygen is the rate-controlling step, then the depth 5 of the internal-oxidation zone is given by where y is a dimensionless parameter and t the oxidation time. Based on the solution of the diffusion equation, wagnerl0 has shown that under certain conditions several mathematical simplifications may be used in the evaluation of y, so that Eq. [I] may be expressed for the case that y « 1, and y(Do/DB) 1, where N(so)the is the equilibrium solubility (mole fraction) of oxygen in the solvent metal for the given oxidizing atmosphere, is the mole fraction of the solute metal in the bulk alloy, 4 is the diffusivity of the solute in the base metal, and v is the ratio of oxygen atoms to solute atoms in the precipitated oxide BO,. Rearranging Eq. [2] Maak' has derived an expression analogous to Eq. [3] for the case that an external-oxide scale, in addition to an internal-oxidation zone, is formed. For this combined external and internal oxidation for the case that 5/2 where 5 is the distance of the internal-oxidation front from the original external s.urface, and X is the distance of the external oxide/metal interface from the original external interface. The function F is defined by the expression

Jan 1, 1964

By W. C. Ellis, M. E. Fine

WHEN certain binary Fe-Ni alloys are worked cold and then stabilized by a stress-relief anneal, their Young's moduli are nearly invariant over a substantial temperature range determined by composition and work-anneal history.' In the present investigation addition of molybdenum to such alloys (besides increasing the yield strength) was found to diminish the sensitivity of the thermal coefficient of Young's modulus to composition changes. Such alloys are of interest for applications requiring 1 a metal with controlled, low temperature coefficient of Young's modulus and substantial magnetic permeability.' Young's modulus ordinarily decreases with rising temperature. In ferromagnetic alloys a change in modulus on heating due to loss of ferromagnetism modifies the .temperature dependence. Far below the Curie temperature ferromagnetism alters the modulus in two ways: a—Addition of the energy of magnetization, a function of interatomic distance, changes the relation between interatomic energy and distance.' This lowers the modulus in the Fe-Ni and Fe-Ni-Mo alloys of this investigation. b—An applied stress changes the ferromagnetic domain arrangement so that linear magnetostriction contributes to the strain and further lowers the modulUs.~ Since in the alloys of this investigation both effects lower the modulus, loss of ferromagnetism on heating changes the slope of the modulus-temperature curve in a positive direction. With increasing temperature the slope of the modulus-temperature curve, due to progressive loss of ferromagnetism, becomes less negative, goes through zero (the modulus is minimum), becomes positive, and resumes its normal negative value above the Curie temperature.' The increase in modulus and decrease in curvature in the modulus-temperature curve occurring on work hardening have been attributed to a reduction in effect (b).'. Vn the absence of ferromagnetism work hardening through introduction of residual strains would be expected to decrease the modulus.' Alloy Preparation—Test Methods Four series of alloys having nominal molybdenum contents of 5, 7, 9, and 10 pct and containing 47 to 58 pct Fe (the analyzed compositions are given in Table I) were melted in air and cast as bars weighing from 2 to 6 lb. The charge consisted of electrolytic nickel, Armco iron, molybdenum (99+ pct) or ferromolybdenum (62 pct Mo), manganese, and aluminum as a deoxidizer. The bars were swaged cold to the desired diameters with intermediate anneals. Alloys in this composition range are reported" to be face-centered cubic and ferromagnetic at room temperature. The Curie temperatures" decrease with molybdenum. For example, keeping the Ni/Fe ratio at unity and increasing the molybdenum from 0 to 17 pct decreases the Curie tempera- ture from approximately 500°C to room temperature. (The 17 pct Mo alloy requires quenching to retain a single phase.~) Young's modulus at a series of temperatures from —50" to 100°C was determined by a dynamic method previously described.', " In this method Young's modulus is calculated from the resonant frequency (in this case approximately 50,000 cycles per second) of a rod sample (approximately 2 in. long) vibrating longitudinally in the first mode. The densities of the samples at room temperature, Table I, were determined by the standard method of weighing in air and reweighing in redistilled bromobenzene. The linear coefficients of expansion, Table I, needed to calculate the sample length and density at the temperature of measurement, were obtained by observing the change in length (22" to 100°C) of an 8 in. gage distance with a two microscope cathetometer. The values of density and coefficient of expansion in the few samples checked are independent of treatment to the accuracy reported. This was assumed to be general for all the samples. The modulus values are accurate to &0.05x101' dynes per sq cm. However, values of thermal change in modulus are accurate to 20.005~ 10" dynes per sq cm. Young's Modulus Values at 25°C: The modulus values of O', 5, and 10 pct Mo alloys at 25 °C are plotted in Fig. 1 as functions of nickel. After working cold, the samples were either recrystallized at 950" to 1000°C or given a low temperature stabilizing anneal at 400° C. The 400°C anneal does not reduce the hardness nor cause recrystallization. Annealing at 400 °C does

Jan 1, 1952