Search Documents

By John A. Garcia

A standard set of coal mining laws for the entire United States is hardly practicsble, yet the numerous variations in the state laws for almost every item seems entirely unnecessary. The same useless variations appear in almost every comparable section with no apparent reason except that no attempt has ever been made to codify them, and as they were developed over a long period of time by innumerable individuals and legislatures, the present situation is the logical outcome of lack of cooperation between states. The ventilation of a mine is affected indirectly by many provisions not listed specifically under this heading, so that it would be necessary to tabulate the major portion of all the laws to secure a complete comparable digest; therefore only a few of the more important have been set down here. This point is well illustrated in the section providing for clearance between car and rib, which is intended as a safety measure against personal injury, but is very important from the standpoint of ventilation because of choked airways in mines on two-entry system. Confusing Phraseology Misinterpretation and confusion may be expected from the phraseology alone; one state provides that the scale of the mine map shall be "not more than 100 ft. to 1 in.;'' another state demands "not less than 100 ft. to 1 in." Both probably mean the same thing and seek to prevent the operator from furnishing a map on which the workings will appear SO small that the detail is illegible. Legislation is certainly indefinite that specifies structures must be fireproof when "near" a mine opening, and just what is a "dusty" or "gaseous" mine is open to argument in most of the states. The variation in spacing crosscuts and break-throughs and the limited number of men on a split seem entirely unnecessary, as the distance is not reduced in gaseous fields, excepting in Arkansas and Tennessee, which states produce a comparatively small amount of coal, and the number of men differs 100 per cent. and more for no apparent reason.

Jan 1, 1927

By T. V. Moore

IN many of the important problems of the petroleum engineer, it is necessary to know accurately the laws governing the flow of gas and liquid mixtures in vertical' pipes. Although much work has been done along these lines, no satisfactory solution to the problem has been found. A good theoretical discussion of the energy balance in a gas¬lift has been published-by Versluys.1 One of the most important factors affecting the efficiency of the flow of oil and gas mixtures is slippage, and in most of the experimental work that has been done no provision has been made for the measurement of this quantity. As Versluys pointed out, since there is no method now known to estimate it from the data usually taken; slippage must be determined empirically. This paper presents the results of some work carried on to, measure slippage in short experimental gas-lifts. As shown herein, slippage can be easily calculated in a vertical pipe carrying a mixture of oil and gas if the fractions of the pipe occupied by liquid and gas respectively are known. In this work, the fraction of the pipe occupied by the liquid was measured under a wide variety of conditions and the relationship between this fraction and other quantities, which are easily measured in ordinary work, was determined. It was hoped that the quantitative relationship obtained from this work could be used-for making accurate calculations in flowing or gas-lift wells, but unfortunately it did not check satisfactorily when applied to actual wells. Apparently flow in long flow pipes is mote efficient than in the short ones used for the experimental work. Nevertheless, it is felt that the data themselves are of interest; that the method of attack may be of value in future work and that the relationship derived between slip and the relative velocities is a contribution toward the solution of the gas-lift problem.

Jan 1, 1931

By R. D. Sprague, C. B. Richardson

The year 1938 was the most active and successful in the history of the oil industry in southern Louisiana. Drilling showed a 16 per cent increase over that of 1937, with a total of 538 wells drilled, which yielded 315 oil wells, 19 distillate wells, 4 gas wells and 200 dry holes. Nineteen new fields were discovered during the year, all but three of which were completed by plugging back to sands previously drilled through. Electrical logging played a large part in these new discoveries as well as in the discovery of new sands during routine development of fields. Fourteen of the new discoveries produced oil, and five produced only gas and distillate. Southern Louisiana continues to lead the world in depth of drilling, which is in part due to the great thickness of comparatively young deltaic sediments near the coast and the existence of numerous sands. The present development is rather evenly distributed over a coastal strip 100 miles wide. New Fields North Tepetate, Acadia Parish.—Atlantic Refining Company's No. 1 Klumpp was completed for a new field through perforations from 7960 to 7970 ft. The initial production was 65 bbl. of 54" gravity distillate and 4 million cubic feet of gas daily through a 1/4-in. choke with tubing pressure of 2850 Ib. and casing pressure of 2930 lb. The well is in see. 12, 7 S., 2 W., just north of Tepetate field. It was drilled to a depth of 8705 ft. and plugged back for its final completion. Atlantic's NO. 2 was completed in a new sand at 8300 ft., also for distillate. South Crowley, Acadia Parish.—Humble Oil and Refining Company's No. 1 Boyd Finch was completed in July 1938, as an oil well through perforations from 7318 to 7325 ft. after plugging from a total depth of 10,222 ft. After making several hundred barrels of oil, the well went to

Jan 1, 1939

By Andrew B. Crichton

No more important question has come before the coal industry in the past decade than the prevention of stream pollution by mine drainage; especially in Pennsylvania, where large areas of coal land have been developed. It may be thought that the problem of labor or lack of transportation outweighs in importance that of stream pollution. We can see possible remedies for labor and transportation problems but there is no known satisfactory solution of the mine-drainage problem. The subject has been given little serious attention, for, until recently, it has been little understood; but in the past year it was brought to the attention of the coal-mining industry by the introduction, in Congress, of several bills designed to prevent the discharge of acid waters from mines or other sources into navigable streams, or their tributaries. The first legislation proposed was the Applebybill, H.R.7369, designed particularly to prevent the oil pollution of coastal waters. It contained the following provisions, which the coal men regarded as referring to the coal industry. It shall be unlawful to throw ... any refuse matter of any kind ... into any navigable waters of the United States or into any tributaries of any navigable waters from which the same shall float or be washed into such navigable waters. The chemical, steel, paper, and other manufacturing industries, as well as the mining industry, objected to this clause, the miners claiming that it would prevent the discharge of waste or mine drainage into any waters of the United States, for all streams or tributaries finally reach navigable waters. The next bill introduced was that of Congressman Briggs, H.R. 7430, an amendment to Section 13 of the Pollution Act of March 3, 1899. The original act referred chiefly to oil and oil refuse, but it provided also "that no material of any kind should be deposited on the bank of a navigable water, or tributary, which might reach the waters and interfere with or

Jan 1, 1923

By William Glenn

The taking of proper samples of crude ores seems to he less thoroughly understood, or less carefully practiced, than its impor tance requires. We all know how often we encounter the reports of very accurate assays and analyses, the weight of which as evidence wholly depends on the method of obtaining the sample, and is very probably nil, because there has been no proper sampling. Pissages might be cited from technical books, and from current technical literature (all the work of writers whom we delight to honor) to show that even among high scientific authorities there is too little acquaintance with the practical art of the sampler. There is no metallurgical or chemical establishment which does not frequently receive samples truly representing nothing. They consist usually of bits of ore, or what not, selected because they are worse or better than the average of what they are meant to represent. And they are worthless, no matter who made the selection. Where conscious choice is permitted to enter into the operation, a fair sample will not result, unless by a miracle. The work of sampling is often looked upon as within the realm of boys and of pensioners only. At least, though the manual labor be left to subordinates, the principles on which it is conducted and the safeguards with which it is surrounded are not unworthy of the study of experts; and experts should he ready to teach these principles and enforce them in practice. For exact sampling is the indispensable first step towards learning the value of any boxful, carload or shipload of ore. I propose to give a simple account of the method of sampling by hand, such as I have always pursued. There is nothing new about it. So far as I know, it is the immemorial old method, as old at least as Cornish copper-mining. Perhaps my fellow-members in the Institute may suggest improvements in it. If not, it will constitute a record in our Transactions to which laymen and beginners may be referred.

Jan 1, 1892

By Andrew B. Crichton

No more important question has come before the coal industry in the past decade than the prevention of stream pollution by mine drainage; especially in Pennsylvania, where large areas of coal land have been developed. It may be thought that the problem of labor or lack of transportation outweighs in importance that of stream pollution. We can see possible remedies for labor and transportation problems but there is no known satisfactory solution of the mine-drainage problem. The subject has been given little serious attention, for, until recently, it has been little understood; but in the past year it was brought to the attention of the coal-mining industry by the introduction, in Congress, of several bills designed to prevent the discharge of acid waters from mines or other sources into navigable streams, or their tributaries. The first legislation proposed was the Applebybill, H.R.7369, designed particularly to prevent the oil pollution of coastal waters. It contained the following provisions, which the coal men regarded as referring to the coal industry. It shall be unlawful to throw ... any refuse matter of any kind ... into any navigable waters of the United States or into any tributaries of any navigable waters from which the same shall float or be washed into such navigable waters. The chemical, steel, paper, and other manufacturing industries, as well as the mining industry, objected to this clause, the miners claiming that it would prevent the discharge of waste or mine drainage into any waters of the United States, for all streams or tributaries finally reach navigable waters. The next bill introduced was that of Congressman Briggs, H.R. 7430, an amendment to Section 13 of the Pollution Act of March 3, 1899. The original act referred chiefly to oil and oil refuse, but it provided also "that no material of any kind should be deposited on the bank of a navigable water, or tributary, which might reach the waters and interfere with or

Jan 1, 1923

By C. B. Richardson, R. D. Sprague

The year 1938 was the most active and successful in the history of the oil industry in southern Louisiana. Drilling showed a 16 per cent increase over that of 1937, with a total of 538 wells drilled, which yielded 315 oil wells, 19 distillate wells, 4 gas wells and 200 dry holes. Nineteen new fields were discovered during the year, all but three of which were completed by plugging back to sands previously drilled through. Electrical logging played a large part in these new discoveries as well as in the discovery of new sands during routine development of fields. Fourteen of the new discoveries produced oil, and five produced only gas and distillate. Southern Louisiana continues to lead the world in depth of drilling, which is in part due to the great thickness of comparatively young deltaic sediments near the coast and the existence of numerous sands. The present development is rather evenly distributed over a coastal strip 100 miles wide. New Fields North Tepetate, Acadia Parish.—Atlantic Refining Company's No. 1 Klumpp was completed for a new field through perforations from 7960 to 7970 ft. The initial production was 65 bbl. of 54" gravity distillate and 4 million cubic feet of gas daily through a 1/4-in. choke with tubing pressure of 2850 Ib. and casing pressure of 2930 lb. The well is in see. 12, 7 S., 2 W., just north of Tepetate field. It was drilled to a depth of 8705 ft. and plugged back for its final completion. Atlantic's NO. 2 was completed in a new sand at 8300 ft., also for distillate. South Crowley, Acadia Parish.—Humble Oil and Refining Company's No. 1 Boyd Finch was completed in July 1938, as an oil well through perforations from 7318 to 7325 ft. after plugging from a total depth of 10,222 ft. After making several hundred barrels of oil, the well went to

Jan 1, 1939

By Joseph W. Richards

This method of briquetting flue-dust, or flue-dust mixed with fine ores, or, in a few exceptional cases, coke-dust, has come into large commercial use in Europe, and a small plant is already in operation in the United States. It promisea to become of such great importance to the iron industry of the United States that the following description will certainly interest the majority of our pig-iron producers. Discovered in 1908, the process Tests upon the observation of Dr. Schumacher that blast-furnace flue-dust, while possessing of itself no binding or cementing properties, acquires strong cementing properties if mixed with a very small amount of certain salt solutions, the amount of which is so small that the resulting cementation appears to be rather by catalytic action of the salts added than by the mass-action of such chemicals. To be more specific, fresh blast-furnace flue-dust mixed with from 5 to 10 per cent. of its weight of magnesium chloride or calcium chloride solution—that is to say, with from 0.25 to 2 per cent. of its weight of magnesium chloride or calcium chloride—acquires the property of setting within a short time, from 15 to 60 min., and forming a hard cemented briquette. Alkaline solutions appear to have no action such as described, and they even interfere, if present, with the action of the magnesium and calcium solutions. When treated in this way the flue-dust briquette sets very hard, apparently from pure excess of cementing- and setting-power. It is, therefore, possible to mix with the flue-dust a considerable proportion of inert ore or like material, which has no setting-power by this process, and thus to make a compound briquette containing large quantities of ore mixed with flue-dust, but in which the flue-dust may be regarded as the cement or binding-material. A particularly strongly cementing flue-

Jan 1, 1913

By Carl Belser

This paper summarizes the data on the oil-shale deposits of western Colorado, Utah and Wyoming. It is based on published reports by the U. S. Geological Survey, on the results of core drilling and sampling by the Bureau of Mines, on the drill cuttings from the Genera1 Petroleum well, on a recent unpublished report by the Geological Survey on the geology of Naval Oil-Shale Reserves No. I and No' 21 and from information supplied by geologists of private companies who have investigated the Green River formation. The paper also contains a revised estimate of the grade and tonnage of minable thicknesses of oil shale of western Colorado. Introduction The oil shales of the Green River formation of Colorado, Utah and Wyoming comprise an important natural resource for the production of synthetic liquid fuels. The oil shale in western Colorado generally is more amenable to exploitation, apparently richer, and probably more persistent than in Utah or Wyoming. Work is now being done by the Bureau of Mines near Rifle, Cola. to ascertain the best procedures for mining the oil shale, producing shale oil from the oil shale, and converting the oil into more salable products. As a part of this program, holes were drilled and cores were taken of the oil shale on Naval Oil-Shale Reserve No. I. In addi- tion, drill cuttings were obtained from a well drilled through the Green River formation by the General Petroleum Co. about 18 miles northerly of the Naval Oil-Shale Reserve. Geology During middle Eocene time a broad, shallow body of water, now called Uinta Lake, covered northwestern Colorado and east-central Utah; a similar lake, known as Gosiute Lake, was in southwestern Wyoming Each of these contemporary lakes was bounded by high hills; the drainage was to the south. The Green River formation was laid down as sediments in the bottoms of these lakes. It is 3000 ft thick and has been divided into the following four members:

Jan 1, 1949

By J. Parke Channing

THESE days of great industrial and social problems in America produce many suggested solutions and great changes. The practical engineer and employer of labor views these problems differently from the labor leader or the social reformer, but as never before he is sincerely interested in solving them in a way that will be just to all. The inevitable tendency of the day is toward "industrial betterment," "safety," "industrial education," "efficiency," and the many other things' which have become so familiar to progressive employers. There is no longer any question that these things are worth while from both the hu¬man and economic standpoints. They "pay" in dollars and cents. The very center of final success in improving conditions and increasing the efficiency of workingmen must be the spirit of fairness and a knowledge on the part of the employer of how to deal sympathetically and intelligently with his employees. Every progressive employer knows how greatly he desires foremen, superintendents, managers and others who possess these qualities. On the other hand, we are all familiar with serious mistakes made by young graduates of engineering schools who have had no opportunity to develop these qualities, and who have no real appreciation of the worth of the workers. Indeed, one wonders whether much ill-feeling, labor difficulties, and many strikes could not be avoided if such men had the right attitude. Is there any way of remedying this condition? If this particular difficulty can be solved, if these young engineers, many of whom are our coming leaders of industry, can be given the right perspective and the right understanding of these other problems in addition to fair, sympathetic methods of handling men, many of our other problems will be solved-not at once, but gradually and permanently, as these men make good and become influential in paths of industrial righteousness and industrial peace. Many progressive employers of to-day have enlarged their own perspective and realize the great importance of enlarging the perspective of those who shall follow them.

Jan 3, 1915

By T. V. Moore, H. D. Wilde

In many of the important problems of the petroleum engineer, it is necessary to know accurately the laws governing the flow of gas and liquid mixtures in vertical pipes. Although much work has been done along these lines, no satisfactory solution to the problem has been found. A good theoretical discussion of the energy balance in a gas-lift has been published by Versluys.1 One of the most important factors affecting the efficiency of the flow of oil and gas mixtures is slippage, and in most of the experimental work that has been done no provision has been made for the measurement of this quantity. As Versluys pointed out, since there is no method now known to estimate it from the data usually taken, slippage must be determined empirically. This paper presents the results of some work carried on to measure slippage in short experimental gas-lifts. As shown herein, slippage can be easily calculated in a vertical pipe carrying a mixture of oil and gas if the fractions of the pipe occupied by liquid and gas respectively are known. In this work, the fraction of the pipe occupied by the liquid was measured under a wide variety of conditions and the relationship between this fraction and other quantities, which are easily measured in ordinary work, was determined. It was hoped that the quantitative relationship obtained from this work could be used for making accurate calculations in flowing or gas-lift wells, but unfortunately it did not check satisfactorily when applied to actual wells. Apparently flow in long flow pipes is more efficient than in the short ones used for the experimental work. Nevertheless, it is felt that the data themselves arc of interest; that the method of attack may be of value in future work and that the relationship derived between slip and the relative velocities is a contribution toward the solution of the gas-lift problem.

Jan 1, 1931

By E. P. Haqyes, J. K. Butler

011, and gas development has continued unabated on the Texas Gulf Coast during 1937. Although the number of important new discoveries has not been great, the extensions in older fields, owing to discovery of new sands and the lateral extension of known sands, has been extensive. Twenty-four new producing fields were added during the year, and many of these areas give promise of developing into important producing districts in the future. Alta Mesa, Amelia, Aransas, Clara Driscoll, Five Corners, Hamman, Heyser, Old Ocean, Premont, Seabreeae, Segno and West Columbia have all had major extensions during 1937. The 1937 production for the Texas Gulf Coast was 120,141,429 bbl., or 32f per cent increase over the 1936 production of 90,865,293 bb1. t The total number of producing wells has increased from 6727 to 8968. Well abandonments have becn few and indications are that they will continue to be so. Rigid proration has been and continues to be in effect, and, as a result, wells in the Gulf Coast will have prolonged life. New Fields Tables 1 and 2 contain general information on all fields in this district. The following named fields were discovered in 1937: Aransas County.—Barnsdall Oil Company's No. 1-A Edwards was the discovery well for the Lamar field. It was drilled to a total depth of 9785 ft., plugged back and completed at 7530 ft. in the Frio as a gas and distillate well. Present indications are not very promising for a major field. Bee County.—The McMurray (Strauch) field was discovered by Dirks Bros. No. 1 Strauch at a total depth of 4577 ft. This is a Yegua producer, and had an initial production of 230 bbl. on a 3/16-in. choke. Brazoria County.—The Sandy Point field was discovered by Henry DeArmanls No. 1 Fite, which was completed as a producer at 6501 ft. in the Marginulina-Frio series. Galveston County.—Although the Hitchcock field was discovered in 1936, the first commercial oil producer was completed in 1937 when

Jan 1, 1938

By M. D. Cooper

For the purpose of obtaining some first-hand data in regard to the shooting down of coal in bituminous mines, it was the writer's good fortune to be employed as a shot-firer for almost one year. In all, 6020 shots were fired by him during this period. All of the work was done in what is known as the South Main section of the No. 2 Mine of the Ellsworth Collieries Co., Ellsworth, Pa., a subsidiary of the Lackawanna Steel Go. Position of Shot-firing in the Cycle of Operations The established practice of the Ellsworth Collieries Co. calls first for the undercutting of the coal by electric chain machines across the face of the entry or room. This is followed by replacing any posts removed by the machine-runners, or the setting of new posts or timber, as may be required. After this has been done the machine cuttings are loaded into cars. Then the coal is spragged, and a shot hole drilled to the depth of the undercut. Next in order, the shot-firer loads the hole and fires the charge. The working place is then cleaned up, timbered if necessary, the sides and face squared up, and loose material taken down. The face is again ready to be undercut. Materials Used Permissible explosives were used exclusively in blasting coal. These were Carbonite No. 2, a nitroglyccrine explosive; and three different makes of ammonium nitrate explosives, Tunnelite, Red H, and Mine-ite 5-D. The last-named was used during the greater part of the period. It is interesting to note that even at the beginning of this work, the gases resulting from the explosions of the charges caused no especial distress on. the shot-firer's part and this continued to be the case except on the occasions when a change was made from one class of explosive to another.

Jan 1, 1918

By F. Osmond

When a metal (whether a simple substance, an alloy, or a compound) presents, in each of the smallest parts to which it can be redueed by mechanical division, a constant chemical composition, it is defined as chemically homogeneous. But chemical hombgeneity by no means necessitates mechanical homogeneity. There are no perfectly amorphous metals. Crystalline forces, on the one hand, and tensions or compressions, on the other band, determined by icequalities of temperature in the mass during heating or cooling, give rise in every metal to the formation of geometric elements of structure. These elements may, moreover, assume perfect crystalline forms, with their planes of cleavage; or embryonic crystalline forms, segregated in the midst of. a paste of confused organization; or pseudo-crystalline forms of expansion and contraction, like those produced in the drying of gelatinous precipitates or (most frequently) these different forms associated. 111 either case the adhesions between two adjoining structural elements, respectively homogeneous, may be very different from the interior cohesion of each of these elements. The mechanical properties of this complex aggregate cannot be simple, and, when it is submitted to strains sufficient to produce deformation, the results may be very different according to the type of structure or the manner in which it is affected by the strains. It may be fairly said that a metal does not present a single resistance to tension, or a single resistance to compression, etc., but in fact, at least theoretically, as many resistances to tension, compression, etc., as it may possess coexistent features of structure; only, in any single test, it is the weakest of the resistances involved which makes itself evident. For further explanation, let us imagine a cylinder A B (Fig. I), formed of two similar halves A and B, placed together upon their common base x y. Such a system evidently presents no resistance to axial tension, while it would resist axial compression like a single

Jan 1, 1894

By W. D. Forgeng, D. Beregekoff

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By Paul A. Beck

While the recrystallization properties of most of the practically important metals are known in considerable detail, those of lead are still relatively little known in spite of some valuable contributions in recent years. This condition probably is due to the difficulties involved in applying the usual methods of investigation. The microscopic method of discriminating between the elongated deformed grains of the familiar lenticular shape and the equiaxed recrys-tallized grains is not successful with fully refined lead: lenticular grains cannot be seen under the microscope with any amount of deformation whatever. The probable cause of this phenomenon was recognized long ago. With large deformation the time of recrystallization at room temperaturc is shorter than the period of preparation of the specimen for microscopic examination; with small deformation the deformed grains arc not noticeably elongated in the first place. However, with small cleformation the migration of the grain boundaries can be observed. The only systematic investigations yet published on the recrystallization of lead, those by R. S. Russell, 1-3 make use of the conditions just described. Russell considered recrystallization completed when no further migration of boundaries could be observed. A serious objection to this method arises from the fact that there is no evidence to support the view that grain-boundary migration results only from recrystallization. If such migration does result from other sources after recrystallization is completed—after the deformed grains have been replaced by new unde-formed grains—the "time of recrystallization" as determined by Russell may be too long. Furthermore, the method is subject to the above.-mentioned limitation because of the unavoidable period of preparation of the sample. According to Russell, even with the fastest technique 5 min. clapsed before the deformed samples were ready for examination, and consequently no reearystallization time shorter than 5 min. could be measured. The lack of success in detecting the recrystallization of lead by the usual hardness or tensile tests is again caused by the time necessary for

Jan 1, 1940

By D. Beregekoff, W. D. Forgeng

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By Philip Davidson, Wm. B. Price

The object of this paper is to present, a survey of some of the physical properties of sheet nickel silver when subjected to cold rolling and when annealed at temperatures extending from 350" C. throughout the coininercial annealing range.. A number of alloys were taken from stock and analyzed. Four of these, representing low nickel and high nickel both with and without lead, were chosen for the tests. The analyses were as follows: Alloy Copper, Lead. Iron. Nickel, ManGanese, Zinc, PeR Cent. Per Cent. Per Cent. Per Cent. Per Cent. PEr Cent. A................ 64.68 Trace 0.194 6.73 0.06 remainder B................ 65.82 1.27 0.227 6.17 0.06 remainder C................ 65.44 Trace 0.345 17.83 0.08 remainder D................ 65.60 1.08 0.238 17.77 0.06 remainder These alloys were lolled in accordance with regular mill practice to approximately No. 6 R. & 6. gage. The bars (which were then coiled) were annealed together in a mill muffle and afterwards pickled in a 10 per cent. sulfuric-acid solution and cold rolled in stages of approximately one number (B. & S.) at a time to No. 18 B. & S. gage. After each stage, suitable samples were set aside for physical tests. Additional samples were chosen for tests after the bars were rolled to Nos. 8, 10, 12, and 14 gage. These samples were annealed together in the mill muffle and, after pickling, were finished on 0.050-in. gage, yielding a series of specimens 2, 4, 6, and 8 numbers hard for the subsequent annealing tests. Tensile test pieces 9 by 1 in. (22.9 by 2.5 cm.) were cut from both lots and the central portion was milled to give a test section 2 1/2 in. long by 1/2 in. wide. A distance of 2 in. was marked off on the edge of each specimen with light punch marks. In the case of the annealed alloys, Erichsen test pieces 4 by 235 in. were also taken.

Jan 1, 1921

By Paul A. Beck

While the recrystallization properties of most of the practically important metals are known in considerable detail, those of lead are still relatively little known in spite of some valuable contributions in recent years. This condition probably is due to the difficulties involved in applying the usual methods of investigation. The microscopic method of discriminating between the elongated deformed grains of the familiar lenticular shape and the equiaxed recrys-tallized grains is not successful with fully refined lead: lenticular grains cannot be seen under the microscope with any amount of deformation whatever. The probable cause of this phenomenon was recognized long ago. With large deformation the time of recrystallization at room temperaturc is shorter than the period of preparation of the specimen for microscopic examination; with small deformation the deformed grains arc not noticeably elongated in the first place. However, with small cleformation the migration of the grain boundaries can be observed. The only systematic investigations yet published on the recrystallization of lead, those by R. S. Russell, 1-3 make use of the conditions just described. Russell considered recrystallization completed when no further migration of boundaries could be observed. A serious objection to this method arises from the fact that there is no evidence to support the view that grain-boundary migration results only from recrystallization. If such migration does result from other sources after recrystallization is completed—after the deformed grains have been replaced by new unde-formed grains—the "time of recrystallization" as determined by Russell may be too long. Furthermore, the method is subject to the above.-mentioned limitation because of the unavoidable period of preparation of the sample. According to Russell, even with the fastest technique 5 min. clapsed before the deformed samples were ready for examination, and consequently no reearystallization time shorter than 5 min. could be measured. The lack of success in detecting the recrystallization of lead by the usual hardness or tensile tests is again caused by the time necessary for

Jan 1, 1940

By H. A. Coy, James A. Noble

The Mascot mines of the American Zinc Co. of Tennessee are situated at Mascot, Tenn., 14 miles northeast of Knoxville, on the Southern Railway. The district is centrally located in the Great Valley, or Appalachian Valley Province. Prior to 1900, a small output of zinc was obtained from oxidized ore mined in open pits. In 1900, a shaft was sunk to sulfide ore, and in 1903, a second shaft was put down, neither being as deep as 200 ft. The American Zinc Co. of Tennessee began drilling in 1911, and outlined an ore-body to which its No. 1 shaft was sunk, to a depth of 365 ft. Since that time, the American Zinc Co. of Tennessee has been the only operator in the district. The Federal mining laws have never been in operation in Tennessee and mining lands are as irregular in boundary and area as farm lands. Ownerships are generally held in fee. In most cases the surface and mineral rights are transferred together. Electric power is supplied at 66,000 volts by the Tennessee Power Co., from a hydro-electric plant at Parksville, Polk County, Tenn., 100 miles from Mascot. No other power is used, but an emergency steam plant is held ready in case of interruption of service. Labor is all native and non-union. Negroes are employed for most of the shoveling, and for a few miscellaneous jobs, but for almost no other work. Exploration Exploration is carried ahead of mining largely by surface drilling. Both churn and diamond drills are used. Holes are not spotted according to geometric plan, but to block out ore outlines with the least number of holes. Churn-drill cuttings from each 5-ft. run are mounted for formation record, and in ore ground, all the bailings from each 3 ft. of advance are sampled and assayed. Diamond-drill cores are sampled and a specimen core filed for formation record. In ore ground, all the core

Jan 1, 1925