Search Documents

By T. N. Dixon, J. E. Briggs

A study was made of numerical techniques for solving the large sets of simultaneous equations that arise in the mathematical mode ling of oil reservoir behavior. It was found that noniterative techniques, such as the Alternating Direction Implicit (ADI) method, as well as some other finite difference approximations, produce oscillatory or unsmooth results for large time steps. Estimates of time step sizes sufficient to avoid such behavior are given. A comparison was made of the Point Successive Over-Relaxation (PSOR), Two-Line Cyclic Chebyshev Semi-Iterative SOR (2LCC), and iterative ADI methods, with respect to speed of solution of a test problem. It was found that, when applicable, iterative ADI is fastest for problems involving many points, while 2LCC is preferable for smaller problems. INTRODUCTION With the advent of high speed, large memory, digital computers, there has been an increasing emphasis on the development of improved methods for simulating and predicting reservoir performance. Two-dimensional, three-phase reservoir models with various combinations of PVT effects, as well as gravity and capillary forces, are common throughout the industry. Such models are also available through consulting firms, to anyone desiring to use them. Three-dimensional models will probably be practical in only a few years. We conducted a study of some of the numerical methods used for solving the large sets of simultaneous equations that arise in such models. A typical set of equations for a reservoir model is shown below:

Jan 1, 1969

By A. M. Hall

SULPHUR, even in small amounts, may often be harmful to nickel and high-nickel alloys, causing impairment of mechanical strength and destruction of malleability and ductility, as shown by Merica and Waltenberg.1,2 It may act. either in the form of nonmetallic inclusions produced in the liquid state during furnacing or as reaction products resulting from its diffusion into the solid metal. In recognizing the action of this element, ability to identify its various forms by means of the microscope is often of considerable importance, especially when direct quantitative methods are inapplicable. [ ] Of the sulphur compounds associated with nickel and high-nickel alloys, the sulphides that may be found in malleable nickel, Monel? and Inconel? are an important group. These sulphides were investigated by metallographic methods in order to provide descriptive data by which to identify them. The nominal compositions of malleable nickel, Monet and Inconel are given in Table I. The term "sulphide" is employed here in a very general sense, to designate a substance in which sulphur and one or more metallic elements are combined. The term includes any combinations of compounds and solid solutions. METHOD OF INVESTIGATION Three groups of small laboratory melts were made, one group to represent each of the three types of alloy under investigation. Within each group, a number of ingots with a sufficient variety of chemical analyses were prepared so that the effect of each of the elements entering the complete commercial alloy could be isolated and observed. In most cases, to facilitate metallographic study by exaggerating the number and size of the resulting sulphides, somewhat greater amounts of the minor elements were added than are present in the commercial alloys. Likewise, considerably more sulphur was added than is normal, but not enough to complicate the system. Transverse sections were cut at a point one third of the distance from the butt to the head of each ingot, polished and examined with an inverted stage metallograph equipped with a combination polarizing-analyzing vertical illuminator. The light source was a tungsten-mercury vapor arc lamp.

Jan 1, 1943

By R. H. Hawkins

AN investigation of the applicability of geophysical methods to north-ern Ontario lignite deposits was undertaken early in 1930 by the Ontario Research Foundation at the request of the Ontario Department of Mines TABLE 1.-Formations Associated with Moose River Basin Maximum System Formation Lithology Observed Correlation Thickness, Ft. Pleistocene Marine clays 150 Glacial till (Minimum Interglacial 30) clay and peat Glacial till Lower Cretaceous or Mattagami Fireclay, sand 138 Kootenay (?) Upper Jurassic. and lignite Devonian (Upper) Long Rapids Petroliferous, 50 Portage and black and gray Genesee shale Williams Limestone and 87 Tully (?) Island calcareous shale Devonian (Middle).... Abitibi River Gray fossiliferous 65 Onondaga limestone Devonian (Lower) ?... Moose Rive- Limestone and 50 gypsum Devonian (Loner) Sextant Arkose, clay, etc. 50 Pre-Cambrian Syenite, granite gneiss, etc. Igneous intrusives. . Lamprophyre dikes cut the Abitibi River and lower formations. (Permission of Ontario Dept. of Mines) and was financed in part from a research grant made by the latter organ-ization. The work to date has included gravitational, magnetic and electrical resistivity studies. The gravitational and magnetic measure-

Jan 1, 1933

By Paul Pietrokowsky

THE formation of intermediate phases in the solid state reaction of titanium with silicon, germanium. and tin (of subgroup 4B in the periodic table) was the subject of a recent paper.' Further investigation of the system Ti-Sn revealed the presence of a new compound on the titanium-rich side of this phase diagram. Metallographic evidence indicated that this new phase was situated very close to 75 atomic pct Ti. The present work is concerned with the crystal structure of the intermediate phase Ti3Sn. Iodide-process titanium metal, furnished by the New Jersey Zinc Co., was used in this investigation. The metallic tin was received in powder form from Charles Hardy Inc., New York; its purity was 99.80 pct. The titanium rod was machined into small cups 1 cm in diam and about 1.5 cm in height. The tin powder was compacted, melted, and then placed in the titanium cups and alloyed by electric arc melting in a helium atmosphere. The alloys, weighing approximately 8 g, were sealed in evacuated quartz tubes and homogenized at 1030°C for 5 days. This isothermal heat treatment was terminated by a water quench from the soaking temperature. Filings of the alloyed pellets were sealed in evacuated quartz bulbs and quenched from 1030°C into liquid argon. A 14.32 cm Debye Scherrer X-ray camera was used for the powder diffraction study. The copper radiation was filtered. X-ray diffraction data for the compound Ti3Sn are given in Table I. The data were indexed on the basis of a hexagonal lattice. Good agreement between observed and calculated values of the square of the reciprocal interplanar spacings was obtained with the following expression: (1/d)2 = 0.03810 (h2 + hk + k2) + 0.04410 (l2) Unit cell parameters were calculated by the method of least squares from the reflections (20.3), (22.2), (40.1), and (42.1); ao = 5.916 & 0.004A, co = 4.764 ± 0.004A, and co/ao = 0.805. The relatively small size of the unit cell allowed the unambiguous indexing of most of the reflections from planes of large spacing. An inspection of the assigned indices (Table I) reveals the absence of (hk.l) reflections when 1 2n. A systematic absence of this type leads to the space group C 6/mmc or one of its subgroups. Assuming, for a first approximation, a linear increase in the density of titanium with the addition of tin, it follows that there are two stoichiometric molecules of Ti3Sn per unit cell. The density calculated from X-ray measurements is 5.194 g cm-'. At this point it became clear that Ti3Sn might be isomorphous with Mg3Cd. The 6 Ti and 2 Sn atoms were placed in the following positions of space group D4 6h, C 6/mmc: 6Tiin (h): X 2X 1/4; 22;; 1/4;Xx 1/4;x2x3/4; 2x x 3/4; x x 4; with x = 516 2 Sn in (c): 1/3 2/3 1/4; 2/3 1/3 3/4.

Jan 1, 1953

By W. B. McCarter

Broadly speaking, the year 1934, one of the most active in the history of the Coast, has been both disappointing and revealing. Of the 18 new oil-producing areas, only two have shown the qualities of a first class oil field. Many of the new areas are discouraging for the horizons exploited, because of close association of gas and salt water, and the absence of any appreciable oil zone. In spite of amply fulfilling the expectations of drilling and geophysical development, the year has fallen far short of the results that normally should be expected from such a campaign. In 1934, the Cockfield zone has been disappointing because its exploration down the dip from the Conroe and Tom Ball fields revealed only such distillate fields as Splendora, Eureka, and the great gas-sand thickness at Katy. The zone proved good at Raccoon Bend. Newer Oligocene and Frio fields in Texas, with the exception of Hastings, were also disappointing, as Van Vleck arid Old Ocean attest. The discovery at Dickinson is not startling. The development of Hastings, Tom Ball, Dickinson and the deep zone at Raccoon Bend will be slow. A new strip of prospective territory of minor importance lying inland from the Conroe trend was opened by the Kittrell discovery. During the year 206 unproductive wildcats were drilled on the Texas Coast, compared with 207 during 1933 and 141 during 1932. During 1934, there were 835 oil and gas wells and 229 dry holes drilled in proved fields, in contrast with 1100 in 1933 and 512 in 1932. The past year's production was actually 60,868,260 bbl., or 2,020,764 bbl. less than in 1933. The present annual rate of Texas Gulf Coast production is about 61 million barrels per year. The daily Texas Coast production decreased 5537 bbl., or 3.2 per cent, during the year. The total daily production at the end of the year was 173,598 bbl. Eighteen wildcats opened up new oil and gas pools during 1934, so that there are now 78 active pools and 3753 producing oil wells. The production of the average well is 45 bbl. per day. The price of crude oil was almost uniform in 1934,

Jan 1, 1935

By H. I. Altshuler

THE mines operated by the Compañia de Real del Monte y Pachuca, Pachuca, Mexico, are in two districts, the Pachuca, and Real del Monte. The principal area of mineralization is within a rectangle roughly 10 miles from east to west and 6 miles from north to south. It contains a number of veins from 2 to 20 ft. wide, which are exploited by this mining company. The scattered position of the producing mines led to the construction of two mills between 1906 and 1908; the Loreto mill, in Pachuca, averaged 2600 tons daily, and the Guerrero mill, in Real del Monte, milled 1270 tons daily. On Feb. 1, 1929, the management decided to enlarge the Loreto mill to take the combined tonnage of both mills at that time. This economic measure required the centralization of ore delivery, which would also afford a material saving in the cost of ore transport. The centralization would give the company the following advantages over the former system of operation: 1. Beneficiation at a single mill, closer to source of materials and supplies than the abandoned- Guerrero mill. The refinery is, also in the Loreto patio. 2. Ore delivery to surface at one point (San Juan Pachuca shaft) instead of at four. 3. Elimination of aerial tramways. To show what would be required to effect this centralization, it is necessary to describe the means by which the ore was delivered to the two mills, prior to centralization. The heart of the Real del Monte district is roughly four miles from that of the Pachuca section. The producing mines in these two districts were: Pachuca district: Santa Ana mine Camelia group

Jan 1, 1934

By C. S. Barrett, P. Coheur

AXnealing twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the re-crystallization texture,' and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (III), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3'4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture— this is true, for example, with the (113) [ZII] texture so commonly reported for brass—hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism. Materials and Methods The samples investigated were of secondary copper (melted in belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice have not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip I. cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a camera2 that traversed

Jan 1, 1947

By G. Willard Quick

TENSILE tests of rail steels at elevated temperatures'' have shown that certain rails, in addition to having low ductility in the well-known bluebrittle range in the neighborhood of 200° C., have marked reduction in elongation and reduction of area in the temperature range from 400° to 700° C. This range of low ductility was called "the secondary brittle range" and the phenomenon, "secondary brittleness." The question naturally arises as to whether this property of the steels would be shown by impact tests performed in the same range of temperature. If so, the impact test, as suggested by Gillett3 would be a simpler and quicker method for the routine examination of steels at elevated temperature than the tensile test. A number of investigators have reported results of impact tests on steels at elevated temperatures, in which the energy absorbed decreased with increase of temperature above 200° or 300° C. Langenberg4 performed Charpy impact tests on several steels at temperatures ranging from room temperature up to 1000° F. (538° C). His results showed an increase in the energy absorbed in specimens tested in the range from room temperature to 200° or 300° C. and then a gradual decrease in the range, 300° to 538° C., the maximum temperature used. Greaves and Jones5

Jan 1, 1932

W. P. Blake, Shullsburg, Wis.: I desire to express my admiration of Prof. Posepny's memoir, and particularly of the charming manner and spirit of the introduction. With respect to his mention of the ore-deposits of Missouri and Wisconsin, reference may be made to my paper presented at this meeting (Trans., xxii., 621)) showing the existence of dislocations and breaks in the bedding, and their apparent close relation with the localization of the ore-deposits as claimed by Dr. James G. Percival, and also so claimed by Dr. Jenney in his paper before us (Trans., xxii., 171). I have in my paper given reasons for believing that the zinc- and lead-ores in the strata above the compact Trenton limestones were formed by lateral secretion and concentration from above downwards, substantially as shown by Prof. J. D. Whitney, and not by the ascent of solutions through the fissures, as Prof. Posepny (p. 304) seems inclined to believe. In regard to the contemporaneity of the ore and the rocks, and in favor of a later introduction of ore through fault-fissures, Prof. Posepny (p. 310) cites the influence of these fissures. In my paper, already referred to, I have endeavored to show how faults may have influenced the deposition of ore without being themselves channels for the flow of mineral solutions, and how they may have caused the contemporaneous formation of metallic sulphides from sea-water in the body of a forming rock; the faulting fissure being formed at an early period in the foundation rocks, and probably continuing to be a plane of break and movement in the deposits of later formation.

Jan 1, 1894

By H. H. Stout

IN the early fall of 1925, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point, The apparatus consisted of a vertical 1-in. dia. silica tube about 12 in. long, heated on the outside, The cathodes were broken to pass a8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in, long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to i500° to 1600°F. and the gas treatments lasted from 3 to 6 hr, The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc, had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F," Smoot's reaction, after a few moments considera-tion, was, "It looks perfectly all right to me."

Jan 1, 1940

By John R. Lewis

DURING the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remaining constant, the time for reduction of a given sample of ore is inversely proportional to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i.e., where carbon reacts directly with the ore. Some recent work by Philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the `A' ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author's intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner's theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed' he concludes that: "In general, the carbon in blast-furnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. Martin,' in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the proper sizing of the ore particles. Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1947

By A. F. Meston

Centrifugal force has been used for centuries for separating liquids but machines for doing this are a comparatively recent development. The use of these machines is being extended into many industries but this paper is confined to their use in the oil industry. The centrifugal machine is found at the well where "cut oil" is dehydrated for acceptance by pipe lines; and in the refinery and byproduct plant. In fact, wherever finely divided suspended particles should be removed from an oil, there is a possible use for a centrifugal machine, if the particles have, or can be made to have, a specific gravity different from that of the oil. Centrifugal machines are also used for cleaning fuel and lubricating oils and dehydrating transformer oils. Applications and Results When oil comes from the well mixed with water, it is spoken of as cut oil. Settling often does not remove sufficient water for the oil to be accepted by pipe lines, thus necessitating chemical or other treatment. Centrifuging alone, or following chemical treatment, effectively prepares such oil for pipe lines, as is shown by the following data: WateR, Etc. Wat~R. Etc. Temperature, Oil to Pipe Line, aT StUt at Finish Degrees F. Bel. Per HouR PIE Cent. PEECent Oklahoma lease.... 160 10 10 0.25 Kansas lease....... 125 4 20 0.25 to 2 On the Oklahoma lease, the machine was cleaned of solid material once in 12 hr. At first, it was thought that chemical treatment was necessary to start separation and 1 qt. of prepared compound was added to each 100 bbl. of the cut oil before centrifuging. Later it was found that

Jan 1, 1924

By Bradley Stoughton, Henry M. Howe

This paper presents an experimental verification of some of the predictions made by one of us1 concerning the influence of certain conditions of casting upon the size and position of the pipe, and the position of the segregate, in steel ingots. The predictions which we have been able to verify are the following: A. That the pipe is shortened and the segregate raised: 1. By slow casting; 2. By casting with the large end up instead of down; 3. By retarding the cooling of the top, e.g., by means of a sinking-head. B. That the pipe is shortened by slow cooling. C. That the pipe and segregate lie in the last-freezing part. Our procedure was to cast ingots of wax (commercially pure stearic acid) containing a little bright green copper oleate (usually 1.5 per cent.) under varying conditions; to saw each ingot open along a longitudinal plane passing through its axis; and to examine the longitudinal section thus laid bare. In order to make the segregate or enriched part more distinct in color from the impoverished part, a very little red cerasine was added. An experiment which will be described later showed that the cerasine itself does not segregate markedly, if at all. Hence we may assume that the strong contrasts between the green and red shown in so many of our ingots are due, not to segregation of cerasine, but to that of the green oleate, in the wax which in itself is uniformly reddened with cerasine.

Jan 1, 1908

By H. M. Day

THE constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were con-firmed and supplemented through X-ray analyses by Preston and Stenbeck.3 According to Murphy, at 276° C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower tempera-tures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region.

Jan 1, 1938

By John Chipman, Karl L. Fetters

Tax relationship between the composition of the slag and that of the underlying metal during the refining of a heat of liquid steel may best be studied in the light of the two broad physicochemical concepts of equilibrium and reaction rate. Actual steelmaking processes, typified by basic open-hearth practice, involve such complexities of operating variables that it is impossible to distinguish with any degree of certainty between the general limiting conditions imposed by chemical equilibrium and the effects associated with rates of diffusion or of chemical reaction. Further advances in the physical chemistry of steelmaking will depend upon our ability to distinguish clearly between these two kinds of effects, and the experimental work that must be done falls naturally into two classifications. The first is the study of chemical equilibrium that cannot be carried out with assurance under operating conditions but must be done in the laboratory. The second is the subject of rates of reaction and diffusion and the mechanism of the process as a whole, which can best be studied under operating conditions. The latter is not entirely independent of the former, since its interpretation often requires a knowledge of the equilibrium state. It is the purpose of this and of several papers that will follow to present the results of laboratory investigations of equilibria involving liquid steel and slag. Open-hearth slag is a complex mixture containing at least eight major components and perhaps twice as many whose influence may be classified as probably minor. It is not surprising that progress toward a complete understanding of such a material at high temperatures has been slow. Attempts to apply the established principles of physical chemistry to the behavior of the individual components of this mixture have been beset by an almost complete lack of data on its chemical properties in the liquid state. This has necessitated the adoption of various methods of approximation based upon such assumptions as, for example, that for a given component the ratio of its mol fraction in the slag to that in the metal is a constant, or that the molecular composition of the liquid slag is the same as its crystalline constitution after solidification. From the thermodynamic viewpoint, such assumptions are merely useful dodges, which enable one to hazard a guess as to the magnitude of the more fundamental quantities, the chemical potentials and activities of the components of slag. The problem of determining the activity of each substance in an eight-component system seems too complex to be undertaken without the aid of generalizations derived from experimental data on similar systems containing a smaller number of components. Accordingly, it was planned in the present investigation to study the equilibrium of molten iron with the simplest

Jan 1, 1941

By D. K. Crampton

The object of this work was to obtain and correlate information on effect of internal stress in variously drawn tubes on several properties. Also, a simple approximate method of comparing types of stress distribution in such variously drawn tubes was sought. There is also included some work on comparison of single and polycrystalline materials and effect of different types of operation and preferred orientation. Preparation of Material A series of tubes was drawn to study the effect of the type and degree of final reduction on various physical properties and the approximate distribution of stress intensity across the tube wall. The material used all came from a single heat of 70-30 brass melted in a regular production Ajax-Wyatt induction furnace. The analysis of the metal as cast was: copper, 70.36 per cent; lead, 0.04; iron, 0.02; zinc, balance. The material was cast in "shells" with 4 in. outside diameter and in. wall thickness. It was drawn part way down according to the usual standard mill schedule and then by suitable individual schedules to finish by a variety of types and degrees of drawing to the same final cases in every instance; namely, 0.750 in. outside diameter by 0.080 in. wall thickness. The exact final draws, together with the percentage area reductions, diameter reductions and gage reductions are given in Table 1. In fabricating these tubes, rather unusual precautions were observed to insure the elimination of ail variables not under immediate study. All intermediate anneals were carried out at about 1200" F. down to the so-called "cut-in size"; namely, 17/16 by 3/16 in. From this point on, all anneals were made at from 1050' to 1100" F. The greatest care was used all through to have the tubes as free from minor surface defects as possible. When such defects were visible on intermediate sizes they were carefully filed out. On the final draw to 3/4-in diameter the die was aligned with the greatest possible precision in order to insure as straight a tube as possible

Jan 1, 1933

By Clarence Thom

This chapter presents, in summarized form, standard procedures for making separations of minerals from their ores by the froth flotation process to produce marketable concentrates. These are typical mineral separations which are being made commercially with the reagents and conditions generally used in the mining industry. Typical separations are presented for 17 metallic and 11 nonmetallic ores. The review of each includes a brief description of the mineral and the particular problem presented, general market specifications for its concentrates, an outline of treatment method, and kinds and quantities of reagents usually employed. This chapter does not include de- tails about ore preparation (crushing, grinding, and classification), elements of ore and pulp transportation (conveying and pumping), or concentrate preparation for market (thickening, filtering, and drying). In each presentation it is assumed, if not detailed further, that the ore is ground to the economical point of liberation of the minerals to be separated. Specific information, such as ratio of concentration and recovery, that depends upon the grade of ore being treated is considered beyond the scope of this chapter. Effective flotation separations that produce marketable concentrates may produce widely varying results in terms of percent recovery and still be economically profitable operations. Details of plant practice on specific ores are presented in Chapters 16 and 17. In this chapter the chemical names of the reagents are given. The extent to which different reagents are used in flotation plants in the U. S. is presented in Chapter 4. A compilation of the various flotation reagents, their trade names, manufacturers, and use has been prepared by H. T. Spedden. ANTIMONY The principal ore mineral of antimony, stibnite (Sb2 S3), is generally found in the U. S. in ore bodies in association with other valuable minerals such as galena (Pbs), sphalerite (ZnS), chalcopyrite (CuFeS2), or tetrahedrite (3Cu2 S – Sb2 S3), The sulfo-salt minerals of antimony, such as tetrahedrite or pyrargyrite, are often associated with high silver values, so that the presence of antimony may indicate economic importance even though the actual antimony content is low. Antimony is also significant to the mineral economy because of its occurrence in some ores where lead, gold, and silver are the

Jan 1, 1962

By D. K. Crampton, H. l. Burghoff, J. T. Stacy

THE effect of cold-working upon electrical conductivity of copper and of copper alloys appears not to be generally known in detail Although several papers on the subject have been presented, showing variable effects according to alloy composition, it is often assumed that the 2 to 3 per cent lowering of the conductivity of ordinary tough-pitch copper by severe cold-working is typical for copper alloys Because of this situation it was decided to carry out the present work upon several types of copper, copper-zinc alloys over the commercial range of brasses, other binary alloys, and numerous age-hardening alloys in the quenched, and quenched and aged conditions The large number of alloys investigated made it impossible to study every one in the detail it may have merited Inasmuch as several interesting points that could not be satisfactorily explained came to light, further work is contemplated by the authors It is usually considered that the normal effect of cold-work on ductile metals and unordered alloys is to decrease conductivity slightly In alloys that are in the ordered state, as annealed or otherwise heat-treated, cold-working tends to disorder the structure, resulting in very marked lowering of conductivity The random state of atomic arrangement produces lower conductivity than the ordered state for the same composition 1 PREVIOUS WORK previous work in the authors' laboratory has shown the electrical conductivity of several copper alloys to be decreased by greater amounts than might have been expected, in view of the general knowledge on the subject, when cold-worked Guillet and Ballay2 investigated the influence of cold-work upon the resistivity of several metals and alloys, including copper and some copper alloys The increase of resistivity due to severe working was less than 4 per cent for all pure metals tested, while the increases for the alloys were generally higher In the copper-zinc alloys, they found that the increase of resistance due to drawing increased with zinc content, and reported a 21 7 per cent increase of resistance for an alloy containing 67 9 per cent Cu as severely worked Masima and Sachs3 studied the change in electrical resistance of three brass crystals when stretched in the tensile test, obtaining increases in resistance of the order of 3 per cent for 30 to 40 per cent reduction of area of the specimens The resistance decreased again when the cold-worked crystals were subsequently annealed Bardenheuer and Schmidt4 found that the conductivity of copper was decreased by 3 to 4 per cent when reduced 50 per cent by working The conductivity of 72-28

Jan 1, 1941

By A. R. Kinkel

THE Shasta copper-zinc district of northern California lies in the foothills of the Klamath Mountains at the northern end of the Sacramento Valley. It contains two main areas of base-metal ore deposits, the East Shasta and West Shasta districts shown in Fig. 1. The East Shasta includes the area from the Afterthought mine, near the settlement of Ingot on U. S. highway 299 East, to the Bully Hill mine, on the north side of the Pit River, 9 miles to the northwest. The West Shasta, a well-defined northeast-trending district about 8 miles long and 2 miles wide, west of the Sacramento River, Fig. 2, is the western part of the ore-bearing area formerly known as the Shasta copper belt. Referred to in the older writings as a copper arc, this belt was thought to form a crescent extending entirely around the head of the Sacramento Valley, the convex side to the north. Recent studies by the U. S. Geological Survey in cooperation with the California State Division of Mines show that there are two districts, one at each end of the so-called copper arc, which are distinct in geologic structure and ore occurrences, and that there is only sporadic and unconnected copper mineralization between them. Ore deposits of the two districts are similar in mineralogy, that is, they are largely massive pyritic ores containing copper and zinc with minor amounts of gold and silver, but the structure and structural control of ore deposition are different. The ores of the East Shasta district are replacements of steeply dipping shear zones in Triassic rhyolite and shale, whereas those of the West Shasta district are replacements of gently dipping rhyolite of Middle Devonian age and are essentially flat-lying. Thus there is marked lateral control of orebodies by shear zones in the East Shasta district and equally marked vertical control of orebodies by the stratigraphy in the West Shasta district. Geologic Setting The Paleozoic rocks of the West Shasta district range in age from Middle Devonian (?) to Missis-sippian. The oldest formation exposed is the Copley greenstone, probably Middle Devonian. It is composed of volcanic flows, volcanic breccias, and tuffs, all of mafic composition, but contains minor amounts of shale and rhyolitic tuff. Largely submarine in origin, it rests upon a base of older marine sediments, as shown diagrammatically in Fig. 3. The lower part of the formation is made up principally of flows, many of which are ellipsoidal, and the upper part contains most of the pyroclastic material. The formation is at least 3700 ft thick. The Balaklala rhyolite overlying the Copley greenstone is made up of many rhyolitic flows and beds

Jan 1, 1956

By J. M. Donkers, R. de Groot

The various objectives of dredging at sea require different methods and radically different equipment for their optimum fulfillment. In the majority of cases, sea dredging is done by means of dredging equipment connected to a pontoon or ship floating at the surface. As the supporting hull is subject to the influence of waves, swells, currents and wind, the connecting point of the dredging equipment to the hull will generally move relative to the sea bottom with 6° of freedom. The more important hull motions are surge, heave, pitch and roll. Depending on the actual sea and weather conditions and the size of the hull, some of these motions can be so large that dredging equipment of rigid construction (normal or inland dredges) cannot be used. In those cases where mechanical disintegration of the bottom is necessary and where accurate dredging is required, the designer must find a solution for this problem. For cases where the bottom consists of soils that can be handled by plain suction, highly sophisticated dredging equipment such as the trailing suction hopper dredge permit dredging under all but the most severe sea state conditions. This type of dredge picks up the soil from the sea bottom while slowly underway. The drag suction head is fitted on a suction pipe of such flexibility that the supporting ship can carry out all six movements in relation to the draghead (heave, pitch, roll, sway, yaw and surge), while the draghead remains in firm contact with the bottom. The suction pipe is fitted with flexible hoses, a universal hinge, a horizontal hinge, axial turning gland and sliding turning gland with horizontal axis and is suspended flexibly from the ship incorporating swell compensating buffer gear, keeping the wires taut and the draghead bottom contact pressure fairly constant while the dredge moves up and down. Due to the fact that the draghead has a low bottom contact pressure and has little tendency to sink into the bottom, this compensation is not difficult to realize.

Jan 4, 1974