Search Documents

By Stirling Huntley

With the threatened falling off in production of the lighter oil pools of the Tampico embayment in Mexico, a general search of that country for oil-producing regions has resulted in renewed activity in the region of the Isthmus of Tehuantepec, one of the first districts exploited in Mexico. Since the drilling of the first well in the San Cristobal section by the Pearson interests in 1902, drilling has been continuous, except during 1917-1921, when practically all development was stopped by the revolutionary activity. Early in 1921, a drilling campaign was inaugurated for the purpose of testing out the known salt-dome poolfi on the flanks of the salt masses, rather than on their tops where previous tests had been located. On Dec. 7, 1921, the Aguila Co., with which are consolidated the Pearson interests and which has been the only company active in developing this region, unexpectedly drilled into a sand horizon at 3015 ft. with its Conception well No. 18. The hole was unable to handle the production, as a 1400-ft. string of 121/2-in. casing was hanging in the hole, a salt-water horizon drilled through at about 800 ft., was not cemented off, and 3000 ft. of 4-in. drill stem with rotary bit was in the hole. This well's potential capacity was never determined, but it made 7000 bbl. of 25" Bé. oil through the bit and Pin. drill stem, in one of its sporadic flows before sanding up, and thus proved itself capable of the largest potential production of any well on the Isthmus. The well showed salt water before caving and sanding up with the drill stem still in the hole, and will probably never be used for production. Wells Nos. 22 and 23, drilled nearby, have proved disappointments after making good showings of oil. In the spring of 1922, Ixhuatlan wells Nos. 28 and 29, deep tests supposedly on the flank of the known salt cores in that field, went into solid salt; No. 28 at 2250 ft. and No. 29 at 2400 ft. No. 28 was continued in the salt for 1000 ft. before operations were stopped. Later comple-

Jan 1, 1923

By W. V. Vietti, E. P. Hayes

OpeRations on the Texas Gulf Coast during 1936 increased materially over 1935. A number of new fields were discovered and a few of the older fields were extended, both by the discovery of deeper pay sands and by lateral expansion of the known producing horizons. Twenty-seven new fields have been discovered, of which 25 are oil fields and the others are gas fields that have every indication of becoming oil-producing areas. Amelia, Anahuac, Bay City, North Pettus, Placedo, Pickett Ridge and Tomoconnor have had major extensions. Production for 1936 amounted to 91,224,844 bbl., an increase of 21,627,033 bbl., or 31 per cent, over the 1935 production of 69,597,811 bbl. The number of producing wells at the end of 1936 was 6727, as compared with 4851 at the end of 1935. Proration has continued in force, thus decreasing the rate of depletion and the number of abandonments normally expected. New Fields A brief discussion of the new fields follows, in addition to Tables 1 and 2, which contain the general data on these fields. Aransas (McCampbell).-Buckingham and McCampbell No. 1 McCampbell was drilled to 7501 ft., then plugged back to 6560 ft. and completed in the Marginulina for a 100-bbl. flowing well on July 18. Bee County.—The Voss field, discovered by Swiger and Devonian's No. 1 Voss, and the Holzmark field, discovered by Miller and Donzis on the Holzmark farm, are both of the same type structurally and are caused by folding against a fault, one field being on one side of a fault and the other on the opposite side of the same fault. Brooks County.—-Standard Oil Company of Texas Garcia No. 1, the discovery well in the Alta Mew field, and Dick Young's Singer No. 1, the discovery well of Alta Verde, appear to indicate small fields. Garcia No. 1 was drilled to 8022 ft. and plugged back to 2485 ft., at which depth the well made 189 barrels. Lockridge.—This gas field was discovered by Gulf Production Company's Fairfield No. 1, in Brazoria County. It was originally drilled to

Jan 1, 1937

By Thomas T., Read

IT will be recalled that when educational instruction for the mineral industry began at Freiberg, at the beginning of the eighteenth century, the original aim was to organize and systematize the procedures previously followed by young men in gaining -familiarity with the technology then in use. There must have been many other ideas current, even then, as to just what a young man needed to learn in order to become capable of assuming 'responsibility for the supervision and direction of such technical work. The problem in Europe was decidedly different .from that in nineteenth-century America, because some of the European mines were actually owned and operated by the governing authority and the others were supervised, regulated, and taxed by it. The American problem was the e5cient performance of technical operations; the European one was regulatory supervision. It was natural, therefore, that in the development of educational processes in Europe stress was laid on those factors which conserved and protected the interests of the state. The study of mineralogy and geology, leading to correct judgments as to the workability and value of mineral deposits; assaying, which gave the means of quantitative measurements, as did surveying; chemistry, which furnished a better basis of understanding for assaying, mineralogy, and geology; and physics and mathematics, which are the bases for the understanding and efficient use of mechanical appliances, became the core of systematic instruction, for the mineral industry. It was early recognized that men could learn more than was already known about all of these subjects and education took on that dichotomy which still characterizes it; the teaching of established knowledge to the unlearned, and that of extending of the bounds of knowledge, now loosely termed research, which after two and a half centuries of work still shows

Jan 1, 1941

By F. W. Glaser

Iron-silicon alloys have had a great influence, in many ways, in modern industry. Silicon steels have been used almost exclusively for the construction of electrical machinery, but have also become an important material for structures which benefit by the high tensile and yield strengths of this material. In elaborating on the early history of work done on iron-silicon alloys, Greiner, Marsh and Stoughton1 went back as far as 1808, and pointed to Berzelius as the first producer of ferrosilicon. During the last twenty years some very important contributions in the form of studies of the iron-silicon system, as well as of the physical properties of these alloys, have been published. In consideration of the brit-tleness and poor machinability of alloys containing more than 5-6 pct Si, commercial interests have stimulated the research done on iron-silicon alloys, but mainly in the range of 0 to 6 pct Si. Yensen2 has shown the influence of im- purities, such as carbon, sulphur and phosphorus on the magnetic properties of 2, 4, and 6 pct Si alloys. Corson3 extended his investigation of physical properties to approximately 32 pct Si, and attributed the brittleness of the high-silicon material to the particular constitutional features of the alloys. Though mentioned earlier in the literature, the effect of nitrogen on crystal growth and magnetic permeability of iron-silicon alloys has been demonstrated recently by Morrill4 and Rostoker,5 respectively. In all the above quoted investigations, except that of Rostoker,5 sand or chill casting processes were employed for the preparation of samples. A major advantage of the powder metallurgy process is that it does away with time-consuming machining in many applications. The powder metal industry is always interested in pro- ducing a finished product employing a material which has presented considerably greater difficulties in manufacture by other methods. Steinit26 described preparation and testing of various Fe-Si alloys which were produced by the powder metallurgy process for the manufacture of armatures for small electric motors or generators. While Steinitz investigated alloys up to 6 pct Si, Rostoker5 went as high as 9 pct Si. The author7 previously discussed the diffusion of iron-silicon compacts containing 6 and 10 pct silicon. It is the object of this paper to study the progress of diffusion occurring in iron-silicon alloys by electrical resistivity measurements. All samples were prepared by pressing and sintering of compacts. Iron, silicon, and Fe-Si powders of various mesh size and compositions were employed to obtain test samples. It was assumed that complete diffusion had been obtained when the electrical resistivity reached a constant value characteristic for that particular alloy. To this end, electrical resistance measurements were used to follow the progress of alloying under various conditions.

Jan 1, 1950

By Michael Perch

The fact that coal is a complex organic material and heterogeneous in composition has made its study extremely difficult, particularly in regard to obtaining a fundamental concept of the processes involved in the formation of coke. It has been stated recently that coals are natural polymers and that in a complex reaction such as occurs during carbonization the differences between coals are quantitative and not qualitative. Such being the case, it would be expected, therefore, that a series of coals subjected to exactly the same conditions of coking would produce results that should be related quantitatively to the chemical analyses of the individual coals. In the past, however, this fact was not generally recognized and consequently many empirical test methods were devised for testing coals. The interpretation of the results obtained depended upon comparing a set of data with other data on coals of known characteristics. The testing procedure had to be con- ducted in precisely the same manner each time and not the least requirement in making the interpretation was experience. The test methods varied from those utilizing a gram of coal to the plant-scale tests in which one or more ovens were charged with the test coal. The aim had been principally to find some simple, inexpensive means by which the coke-making and other properties of coal could be predicted. It is not necessary to emphasize the importance of these endeavors, for anyone acquainted with the problems involved in the selection of coals for making coke is well aware of the time and expense involved in making a series of definitive tests.

Jan 1, 1949

By SAM YOUR

PROCESSING, technology and application of non- ferrous metals-copper, lead, zinc, aluminum, nickel, precious metals, foundry metallurgy, less common metals, secondary metals-are the special field of the Institute of Metals Division. New developments in this field during 1930 are more or less briefly out- lined in this review prepared by the papers and publications committee of the Institute of Metals Division as follows:

Jan 1, 1931

THE third annual Joint Western Mining Convention, held at Los Angeles, Sept. 10 to 13 inclusive, was a notable success both as to attendance and interest. Registration the first day amounted to 201, and the total crept up to 347 before the close. The American Institute of Mining Engineers was well represented, approximately 80% of those registered and most of the speakers being members. This illustrates largely the amount of interlocking membership and the reason for holding at one time and place meetings of the several related organizations. The plan has proved so successful that it is probable that Spokane will extend an invitation for next year that seems likely to be accepted. It is proposed that the convention be timed so as to permit visitors from the East to stop there Oct. 3 to 5, en route to the American Institute of Mining Engineers meeting at San Francisco, Oct. 7 to 9. Simultaneously, it is expected that the Petroleum Division will hold its fall session at Los Angeles, the two streams of travel meeting in San Francisco, just before departure of the party of engineers traveling to Japan to attend the World's Engineering Congress. The Los Angeles meeting opened Monday morning with a general session under the auspices of the Western Division of the American Mining Congress with Philip Wiseman in the chair. After a series of short responses to the welcome extended, Charles W. Merrill discussed the needs of the western mining industry. A complimentary luncheon to members and delegates followed.

Jan 1, 1928

R. G. BROWN, Bodie, Cal.: Mr. Rickard's paper, with its valuable illustrations, brings into fresh clearness the game of hide-and-seek which the miner must play with his ore-deposit; but, more than this, it goes far towards classifying those perplexing idiosyncrasies which, while unclassified, constitute a labyrinth almost without clue. Probably every engineer can add to the list by the mention of at least one fresh detail from his own experience, and I for one would like to comment on two of Mr. Rickard's divisions. To what he has written about " walls within walls" and " walls without walls," the accompanying Figs. 1 and 2 may be appropriate, the more so as they represent conditions obtaining in a part of the Butte copper-belt more typical of the copper-veins as a whole than the Gagnon, which, in some respects the most interesting mine in the camp, stands almost alone in many particulars. (See nuns., xvi., 62.) Fig. 1 was sketched in January, 1895, in the stopes above the 700-foot level of the Colusa-Parrot mine, east of the Parrot and southwest. of the Anaconda. The stope, the commercial foot-wall of which is shown at A, was 30 feet wide at this section, the pay-ore being massive chalcocite, jumbled with bornite, pyrite, quartz and thoroughly broken-down granite. A and At are inch-thick seams of black talc; B, B' and B" are also talc, possibly 1/8-inch thick. In the plane of the section the "banded quartz " and " quartz and pyrite " were both of too low grade for extraction, but 5 feet back along the stope had been of fair value. The granite with quartz and bornite between Bt and A' was pay-ore, but that to the right of B" was not. In both cases the ferro-magnesian minerals had been removed, leaving, where not obscured by ore, faint, dark patches. Between A'

Jan 1, 1897

By Allan D. Taylor

INTRODUCTION From the designer's view, the installation starts with the first definition of the orebody, and progresses through a long and complex development. The design is affected not only by the characteristics of the ore, but by all of the personalities and events of the project during its development. The following discussion attempts to touch on the most important aspects which define the context in which the designer must work in apply the do's and don'ts. That context is the basis of the viewpoint. WHAT CAN GO WRONG The Project Is Going Over Budget This is a common and serious concern to the plant designer. The Project Falls Behind Schedule Another common and disturbing condition with which the plant designer must cope. Some Equipment Fails to Perform This can be due to either faulty equipment or operating deficiencies. It can be the result of a wide variety of causes, but the designer will be an interested party in the search for the cause and the cure. The Plant Isn't Flexible Enough Sometimes a plant will handle some or even most of the ore satisfactorily but is unable to treat another type properly. This can be a significant problem. An example might be a case where low capacity of a cyclone feed pump makes it impossible to accompany an increase in grinding mill throughput with a corresponding increase in dilution water. This could lead to an increase in cyclone feed density, and a loss in product grade or a limit on the plant capacity. Spillage And Cleanup Are Excessive This is one of the most common and annoying defects in metallurgical plants, and one for which the designer can rarely delegate blame. Maintenance Is Excessive Another common complaint in new plants, and also one for which the dedesigner must accept most of the responsibility.

Jan 1, 1982

By Herbert Hoover

THE Federation of Engineering Societies has been created for the sole purpose of public service. This initial meeting surely warrants some discussion of a few of the problems to which this organization, for expression of the --. engineering mind, can quite well give consideration. Some of the greatest of the problems before the country and, in fact, before the world, are those growing out of our industrial development. The enormous industrial expansion of the last fifty' years has lifted the standard of living and comfort beyond any dream of our forefathers. Our economic system under which it has been accomplished has given stimulation to invention, to enterprise, to individual improvement of the highest order, yet it presents a series of human and social difficulties for the solution of which we are groping. The congestion of population is producing subnormal conditions of life. The vast repetitive operations are dulling the human mind. The intermittency bf employment due to the bad coordination of industry, the great waves of unemployment in the ebb and flow of economic tides, produce infinite wastes and great suffering. Our business enterprises have become so large and complex that the old personal relationship between employer and worker has to a great extent disappeared. The aggregation of great wealth, with its power of economic domination, presents social, economic ills which we are constantly struggling to remedy.

Jan 1, 1920

By J. Leslie Goodier

The International Law of the Continental Shelf, so far ratified by 35 nations, extends the national boundary of any coastal nation to the edge of the continental shelf, this normally being at a continuous water depth of 200 m. The Law further extends this boundary to include the floor of the deep ocean to any depth that can be mined by advanced mining technology. In effect, proof of mining can constitute proof of ownership of the subaqueous land and the minerals on or below the sea floor. Irrespective of the fact that present technology is too limited to permit mineral exploitation in the high seas-and the law regarding the right to mine appears hazy-the U. S. Treasury Department's Bureau of Customs, has a ruling that would further deter mining operations on the high seas. This law contends that minerals mined on the continental shelf of the United States are actually mined within the continental United States and are free of tariff, but mined products or other articles obtained from the ocean or the sea floor beyond the continental shelf, if brought into this nation, must be considered as imported and are subject to such customs duties as are applicable under the tariff schedules of the United States.

Jan 7, 1968

By Ralph H. Phelps

WHAT information do you have on precision investment casting? Please send me all available information on the removal of paraffin from oil wells and pipe lines. How can I find out how to remove magnesium oxide from lime? I want a good book on the pickling of steel. Can liquid oxygen be used as an explosive in a mine? Where can I get a bibliography on the plasticity of metals? These questions, selected from the scores of questions asked the Engineering Societies Library staff every day, indicate some of the diversity of the requests received. The samples chosen relate to interests of AIME members but the questions that come to the Library by mail, telephone, telegraph, and in person cover all fields of engineering, science, and technology. Some questions can be answered quickly; others require extensive searching. Those that can be answered in a few minutes or ten, twenty, or even thirty minutes are usually done without charge. For the more difficult questions a charge is made. In this way those requiring considerable service pay for it and the Library finds it possible to serve more persons.

Jan 1, 1948

By AIME AIME

ASIDE from the annual dinner-dance, the two outstanding social events of the Annual Meeting were the dinner- smoker on Monday night and the informal dance on Tuesday night, both of which were held at the Commodore Hotel. Approximately 400 attended the former event, compared with 570 a year ago, and about 250, people were attracted to the dance.

Jan 1, 1933

By Charles H. Fulton

FOR some time it has been thought that there should be > closer relationship between the members' of the Institute engaged in education in the mining schools, the mining, metallurgical, ceramic, and geological departments of universities, and the members of the Institute actually engaged in the production of mineral products and the operation and direction of works. The American Society of Chemical Engineers and the American Ceramic Society have for some years past devoted especial attention to the educational matters of their respective fields. The Engineering Foundation, representing the great engineering societies of the country, is deeply interested in technical education and maintains a Committee on Educational Research.

Jan 1, 1932

By C. W. Pollock

THAT a distressing explosion of some magnitude did not take place in the Berry No. 3 mine of the Ford Collieries Co. recently was solely because no source of ignition was present when the stage was set for such an occurrence. The mines of this company, which are in West Deer Township, Allegheny' County, Pa., have been operating in the double or thick Freeport seam since 1.909. During this entire period they have been classed as gaseous by the Pennsylvania Department of Mines, and some gas has been encountered from time to time almost entirely however in development work in the vicinity of clay veins or wants-and never to my knowledge on gobs or in rib work.

Jan 1, 1935

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselrnan Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo.

Jan 1, 1949

By AIME AIME

Russell B. Paul, Chairman of the Special Committee on Divisional Relationships, presented the interim report of his Committee which was published in the September, 1945, issue of MINING AND METALLURGY and a copy of which is incorporated in the official minutes of this meeting. The following specific actions were taken by the Board of Directors in relation to the six recommendations in the Summary of the Report as published: (1) Mr. Haider, Chairman of the Petroleum Division, presented the formal request of his Executive Committee that the headquarters of the new Secretary of the Petroleum Division be established in Dallas, Texas. After lengthy discussion in which the point was made that the success of this program would depend upon effective co-operation between the Chairman of the Division, the Secretary of the Petroleum Division, and the Secretary of the Institute, the request was approved. The new secretary will be selected by the Division and will be employed by the Institute in the capacity of an Assistant Secretary. (2) The following item in the report was approved:

Jan 1, 1945

By A. A. Brant

Mining men, quite as exploration minded as petroleum interests, are in the position where most of the exposed crustal portions of the earth have been examined, where the demand for metals is high and likely to continue so, and yet where, perhaps, the tools fail for the economic exploration of many of the possible mineral areas more deeply covered with drift, alluvium, and later formations. At the same time the incentive exists to create acceptable substitutes for many of the duties of metal. The problem of the economic exploration of possible mineral-bearing areas is hence a vital one. In oil exploration, the absence of surface or shallow occurrences and the high cost of test drilling has led to the intensive study of geophysical techniques. Hence the development of the seismic method with its high certainty factor and its adaptability to standardized procedure.

Jan 1, 1949

By CARLE R. HAYWARDC

BEFORE discussing this subject it is necessary to define somewhat the meaning of the tern metallurgical.. When I was a student at M. I. T. ore-dressing was not thought of as metallurgy in any sense of the word, but it was considered as more closely allied to mining, enabling the miner to market an otherwise unmarketable product, or at least to market it to better advantage. Progress in ore-dressing has gradually allied it more closely with smelting, for at present the raw material received by the smelter is predominantly concentrates and smelting practice has been profoundly affected by the products of the concentrating mill. It is not surprising therefore that in many schools ore-dressing is frankly considered as metallurgy and although there may be some dissenting opinions it will be considered as such in this discussion. Twenty-five years ago at M. I. T. metallography was taught in a few optional lectures. This subject has developed rapidly and been expanded into the new and increasingly important field of physical metallurgy. To many metallurgists the -term metallurgy means only physical metallurgy. They know little or nothing about smelting and leaching and even less about ore-dressing. Having then broadened the scope of the term metal¬lurgy to cover ore-dressing, smelting, leaching and phys-

Jan 1, 1930

By E. W. Davis

THE large iron-ore producers on the Mesabi Range are able to maintain the silica in their shipping products at from 8 to 10 per cent by mixing ores of various grades, some assaying 4 per cent silica and some as high as 18 per cent silica. For each ton of 4 per cent silica ore mined, a ton of 14 per cent silica ore can be mined and mixed with it and the average grade maintained at 9 per cent. This mixing operation has made possible the utilization of large cluantities of ore too lean to be used alone. and herein lies the advantage of the producers who operate a number of mines at the same time. As the grade of the ore from one of the properties falls off, a little high-grade ore from another property can be mixed with it and the average maintained, while if one property alone were being operated all of the ore below grade would be left behind.

Jan 1, 1930