Search Documents

By AIME AIME

OUR own Institute of Metals and Iron and Steel divisions cooperated with the Iron and Steel Division of the American Society of Mechanical Engineers, the American Welding Society, and the American Society for Steel Treating in a busy week at Cleveland. The morning sessions were held at the Hotel Cleveland and the afternoon ones at the Auditorium, where the metallurgical exhibition under the auspices of the American Society for Steel Treating not only occupied the arena of the Auditorium but completely filled the huge adjacent Annex. In the intervals of sessions the members thronged the exhibits but in the evenings the local attendance was so great that if the crowds had been any larger it would have been difficult to see the exhibits. With so many firms, both producers of metals and of equipment accessory to their production and use, it would be impossible to mention them -all and unfair to single out a few, since no two individuals' judgment would coincide as to relative interest and importance. In any case an exhibit is a thing to be seen rather than described, and these were well worth seeing.

Jan 1, 1929

By E. D. Hummer

During the planning of the fine coal cleaning addition at the Gary, W. Va., Coal Preparation Plant of United States Steel Corp. careful consideration was directed toward the problem of minus 48 mesh refuse disposal. The plant flow sheet included wet screening the raw coal at ¼ in., pumping the minus ¼ in. raw coal to bowl desiltors for desliming, and then cleaning the deslimed raw coal on tables. The material to be removed from the circuit as minus 48 mesh refuse consisted of the minus 100 mesh desiltor overflow thickened in two 120 ft diam thickeners and minus 1 mm screened from the table refuse. Later a flotation plant was added to recover coal from the desiltor overflow, and a classifier replaced the screens to make a sharper size separation of the table refuse at 48 mesh. Today the minus 48 mesh refuse at Gary consists of thickened flotation tailing and thickened spiral classifier overflow. The transportation of large quantities of fine, wet refuse filter cake mixed with jig and table refuse over existing conveying equipment would have been neither dependable nor economical. Filtration was therefore impractical, and disposal of the fine materials was a problem. The decision was to pump the material to storage ponds.

Jan 3, 1965

By B. Prof. Silliman

THE experiments detailed by Dr. Hunt,* having demonstrated the fact that the copper contained in the "clay ore" of Jones's Mine, was rendered completely soluble in the bath of ferrous chloride, used in the Hunt and Douglas process, after heating in contact with carbonaceous matter in a close vessel, I set myself to devise a form of muffle furnace adapted to the treatment of large quantities of these and similar ores by a continuous process. The result is shown in the diagrams on Plate X, reduced from the working drawings, after which this furnace was built early in 1876, at Phoenixville, by the Chemical Copper Company on their works at this place. The peculiar character of this ore determined the form, dimensions, and position, with reference to charging and discharging of these muffles. The ore arrived from the mine with from 20 to 25 per cent. of moisture, and when dried at 212° F., or more slowly at lower temperature, it falls to a light incoherent powder, with occasional lumps of undecomposed rock. In this condition it is readily mingled with coal-dust or any like reducing agent, and requires no other preparation for the muffle than the use of the shovel, to mix it well with the reducing agent. As it is a remarkably good non-conductor of heat, it was obvious that the mass, to be heated through in a reasonable time, must not be too thick, while the weight of the mass must be sustained in a way to avoid undue strain upon the walls of the muffle. These walls must be as thin as practicable, to favor the more rapid transmission of heat, and must, therefore, be so con¬structed as to admit of being stayed on the sides at frequent intervals to resist the lateral thrust of the very mobile mass of pulverulent ore, which, for obvious reasons, must be charged at the top and drawn from the bottom of each chamber. These considerations led to the form adopted, viz., two vertical muffles, standing upon very strong bridge tiles, seen in longitudinal section, on the line E, F, and in plan in Fig. 3, on the same plane. (Plate X.) The vertical section of the muffle is seen in Fig. 4, drawn in the plane G, H, of the longitudinal section, Fig. 6, which is the key to all sections. The walls of the muffles are built of the best firebrick, very care- * See paper by Dr. Hunt, page 325.

Jan 1, 1876

By William Kelly

I AM-glad to have the opportunity at this time to say that I consider it a very great honor to be elected President of the American Institute of Mining and Metallurgical Engineers. It fulfills the proudest hopes of my ambition. There is, ,however, one drawback to my personal gratification-a feeling of unworthiness to have my name placed on the list with former Presidents of the Institute, with the brilliant Raymond who guided our society for so many years, with the versatile and lovable James Douglas, my first employer and my friend, a most generous benefactor of our Institute, with the skilful Holley, who gave to the manufacture of steel in this country, its first great impulse, to mention only three of the accomplished men who have preceded me. I assume that the honor of my being elected President of the Institute is not merely a personal one but that it should be considered a tribute to the wonderful progress in the art of mining, both underground and in open pits, and in the beneficiation of native copper and iron ores, which have been shown in the Lake Superior District and also a recognition of our members there and elsewhere who are living at the mines and directing the operations, upon the success of which the whole mineral industry depends.

Jan 1, 1924

By D. B. Gillies

IN 1938 the Republic Steel Corp. announced that it had leased the ore mines and other property of the Witherbee Sherman Corp. at Port Henry, N. Y. The announcement brought forth an interesting reaction. Two questions were asked repeatedly: (1) Is the iron product high grade? (2) Is there a substantial reserve? The answer to both questions was and is a decided and emphatic "Yes."

Jan 1, 1943

By R. W. Raymond

ALEXANDER BRINTON COXE was born in Philadelphia, Pa., Jan. 19, 1838, the second of five sons of lion. Charles Sidney Core and Ann Maria Brinton. A more extended history of his family and its important relations to the development of the United States will be found in my Biographical Notice of his younger brother, Eckley B. Coxe, published in 1895. It is therefore sufficient to say here that Dr. Daniel Coxe, a distinguished physician and surgeon of London, and a medical attendant of Charles II and Queen Anne, purchased, in 1684 and 1686, lands in East and West Jersey from grantees of the Duke of York, and became Governor of West Jersey, in which capacity he did much to develop the provincial fisheries, the manufacture of marine salt and pottery, the exportation of tim¬ber and the West India trade. In 1698, having acquired the royal patent of the Province of " Carolana," covering (with some reservations) the territory extending from the Atlantic to the Pacific, between the 31st and 36th parallels of N. latitude, Gov. Cole sent an expedition from Charleston, S. C., to the Mississippi. In 1769, seventy years later, his grandchildren surrendered to the Crown their title under this vast and vague patent, receiving in return a grant of 100,000 acres in the Colony of New York. The line of his descendants, so far as they concern this sketch, is as follows 1. Col. Daniel Core, his son, b. 1673, who came to New Jersey in 1700; resided there until his death (1730); held many high offices; and issued in London (1722) A Description of the Provinces of Carolana, containing probably the earliest published plan of political union for the British Colonies in North America.

Sep 1, 1906

By AIME AIME

CHARLES A. CHASE, manager of the Shenandoah-Dives Syndicate, operating the Shenandoah Mines in southwestern Colorado, reviewed the current work at that property at a recent meeting of the Colorado Section, in Denver. This operation is a new one, having been in effect only two years, but the properties that were consolidated by Mr. Chase had had certain production in earlier years, since when they had: been inactive. These properties are located. in the high mountains of the San Juan section in Colorado, and although they had had a substantial production of ores of good grade in the upper levels, the project as a whole involved the bold undertaking of driving through the mountain, starting on the Mayflower claim on the Arrastre Gulch side and passing through the Mayflower, Slide, Terrible, North Star, Dives and Shenandoah No. 3 claims. This is a distance of over 8,000 ft. which is known to be mineralized, and the main operating tunnel was started at an elevation of approximately 11,000 ft. The main exploration work has already extended in nearly 4,200 ft. and the present mining production of nearly 550 tons daily is being secured while the main exploration work is being continued. The main heading is now within the North Star claim and the plan of operations involves continuing ahead for a few hundred feet and then starting an upraise which will he 2,200 ft. high and which will connect with the old workings of the North Star mine. The plan of ruining then will he to drive levels along the vein in both, directions to daylight and retreat downward, taking out all the ore and abandoning, the workings after the ore is removed. In this way one level after another progressing downward will be abandoned. The raise will be of two compartments, one of which will carry the 8-ton skip and the other the counterweight and manway. So far the ore has been broken over an average width of more than 11 ft., with an output of 39 tons per machine shift.

Jan 1, 1932

By Edward H. Robie

AT a recent meeting of the AIME Board there was considerable discussion of a suggestion that companies should be more interested in promoting AIME membership among their employes. The advocate of this idea argued that companies benefit greatly if their employes are active AIME members, so even on purely a selfish basis they should use various means to encourage membership. Also he argued that companies in general make no contribution to the support of the AIMS although benefiting from its work, so should not object to making more of a contribution, financial or otherwise, than they do. One Director stated that an investigation had developed the fact that a large majority of members felt it unwise for employers to pay the initiation fees or dues of employes. They felt that AIMS membership should be on a purely personal basis; that the rewards of active membership were sufficient so that it is a good investment for a man in developing his own professional stature, presumably resulting in an increase in salary sooner, or in greater amount, than would otherwise be the case. If an employer paid a member's dues or initiation fee the member would take less interest in the Institute. But this Director felt that an employer should otherwise encourage his employes to join the Institute, attend its meetings, and write papers based on company work for presentation and publication. Another Director reported that his company pays the expenses of AIME members in its employ to meetings; the company also encourages nonmembers to attend AIME meetings but does not pay their expenses unless they present papers of interest to the company. Another Director, representing a supplier, stated that his company's policy was to send some of its staff to all AIME meetings at which papers of interest were to be presented or at which valuable contacts could be made.

Jan 1, 1952

By Thomas T. Read

EVERYONE engaged in the teaching of mining engineering will, I suppose, agree that the most difficult subject to teach is "Mining Methods." One primary difficulty is that the students taking the course have either had no previous experience in mining, or else they have had; either seeming to be somewhat of a drawback. The students who are unfamiliar with mines find it difficult to visualize underground conditions, as described and illustrated with sketches and maps, while those who have had underground experience seem to 'find it difficult to visualize anything much different from that which they have already seen. This reminds one of the remark about the Presbyterian doctrine of predestination, to the effect that "you are damned ,if you do; and damned if you don't."

Jan 1, 1930

Theo. B. ComstocK, Los Angeles, Cal. (communication to the Secretary*):—Mr. Blake's recent paper upon this topic undoubtedly partly explains the rationale of a part of the known facts bearing upon discolorat'ion and encrustation of rocks. His quotation from Humboldt, with reference to certain South American examples, may be questioned in the light of further facts, which do not appear to bear out the great traveler's theory of causation. There is no available evidence that the waters of the tropical rivers referred to by Professor Blake contain dissolved organic matter in the varying proportions required to demonstrate Humboldt's guess, nor do the concomitant facts in any manner bear out the hypothesis that the blackening in one case and its absence in the other may, perhaps, be traced to differences in the chemical reactions of the respective waters. Careful consideration of Professor Blake's illustrations, in connection with numerous personal observations extending over widely-scattered areas, convinces me that elements of

Jan 1, 1905

By S. Kobayashi, A. E. Armenákas, C. Mylonas

Earlier work1-4 has shown that commercial mild steels under static loading at the lowest natural operating temperatures fracture in a brittle manner only when damaged by a suitable history of straining. Notched and then compressed plates have fractured in subsequent tension at loads as low as 10 pct of the limit load and precompressed smooth bars at a subsequent extensional strain as low as 0.01. The comparison of the average net fracture stress with the flow limit stress was shown to be an excellent criterion of brittle or ductile behavior of mild steel structures when only loads and general stress levels are known. The present investigation shows that the deformation at fracture is a far more sensitive measure of brittleness than the fracture stress. Both criteria, deformation and stress, are used to determine the amount of uniform precompression of two mild steels, ABS-B and Project E-steel, resulting in brittle fracture under the strong constraint of a subsequently machined severe circumferential groove. The fracture stress equaled or exceeded the theoretical flow limit Ól = 2.680., ('based on the elevated yield stress at each prestrain) up to prestrains of about 0.20 and then fell off to about 1 at prestrains of 0.60. Yet a prestrain of only 0.05 reduced the elongation at the shoulders by a factor of about 4. The total plastic elongation of a region surrounding a sharp notch in prestrained steel deternines whether or not fracture will be initiated in large structures, hence is a direct and realistic measure of the remaining ductility and provides an excellent test of the material's resistance to embrittlement. ALMOST all engineering structures of mild steel which failed in service in a so-called "brittle" manner exhibited appreciable local plastic deformation (more than 1 pct) and a mixture of "cleavage" and "shear" fracture surfaces. Furthermore, the peak local stress in an advancing crack is always high. Such simple criteria as pure cleavage, absence of plasticity, or fracture stress, so useful in other fields, are insufficient to characterize brittleness in engineering structures at ordnary temperatures. The "brittle)' behavior of engineering structures is caused by the limited ductility at cracks or notch regions, as shown by recent work at Brown University summarized and extended in Refs. 1 to 4. It was also shown that the local ductility of mild steel may be catastrophically reduced by a suitable strain and temperature history similar to those which may occur in real structures. Localized yielding begins at the notch roots at low loads but is contained by surrounding elastic regions. The plastic strains are hence small. They increase slowly with the load up to the flow limit or limit load for an ideally plastic material. Unrestricted plastic flow then occurs. At such strains the real material locally st rain-hardens and fractures. With work-hardening materials no flow limit exists, and the transition from low to high plastic strains is gradual but increases more rapidly at loads close to the flow limit of an equivalent perfectly plastic material. When the available ductility is sufficient for reaching the limit load, the behavior is normal or "ductile". With insufficient ductility, fracture will occur at a low load and will be defined as "brittle". Accordingly the sufficiency or not of the ductility at a notch is reflected in the magnitude of the fracture load or average net stress as compared with the limit load or flow limit. The application of this criterion gave surprising results. Service failures under semistatic loading occurred mostly below the limit load, hence were "brittle". On the contrary all static tests with undamaged commercial mild steels reached the limit load in spite of the deepest notches and temperatures below Charpy impact transition (say about -30°F or higher). Notched bars showed no brittleness even under fully dynamic axial loading up to 1.5 x107 psi per sec at -23°F and about 2.5 x l06 psi per sec at -ll0°F, but broke in a brittle manner at -200°F and l03 psi per sec.' To propagate a fracture at low load, experimenters had to trigger it by superimposing a strong dynamic impact at a notch cooled by liquid nitrogen as in the Robertson5 or Esso tests.' Once started the cracks would run through warmer regions of smaller stress. Obviously the ductility of the apparently undamaged commercial steels was "sufficient" in the laboratory tests but not in the service fracture, where it must have been reduced by some embrittling procedure of fabrication or service. These conclusions were confirmed by the achievement of low static stress (brittle) fracture initiation in unwelded steel after a local reduction of ductility by simple prestraining. Symmetrically notched plates of undamaged mild steel cooled below the Charpy V-notch transition range were tested in central static tension: Undamaged plates withstood loads of limit intensity, but when subjected to prior in-plane com-pressive prestraining perpendicular to the notch axis and to accelerated aging, the plates fractured completely or partially at very low static loads, as low as one-tenth of the flow limit.2-4 However, damage could not be easily related to the strongly variable prestrain around a sharp notch. To obtain easier strain measurements, it was decided to use axially precom-pressed bars and bent bars. Final testing was done by

Jan 1, 1970

By AIME AIME

RECENT experiments in reflected sunlight photography in mine shaft's' and. slopes in the McAlester, Oklahoma, coal-mining district have been so satisfactory as to indicate that such a method has definite scientific value. The entrances to abandoned deep shafts and slopes on Choctaw and Chickasaw Indian coal lands in Oklahoma are being filled or bulk-headed by the U. S. Geological Survey under Public Works Project F. P. 63-C&C. Inasmuch as these mines may be reopened at some future time when there is a demand for coal, H. I. Smith, Chief of the Mining Division, suggested that photographs of deep shafts would be of value. Such photographs would show timber details and the general condition of the walls. Photographic records of the exact status of shafts when filled will facilitate operations in reopening.

Jan 1, 1936

By L. Leibowitz, M. G. Chasanov, L. W. Mishler

A drop calorimeter system is described for use in measuring enthalpies to 3600°K. Data are presented for tungsten between 2800" and 3600°K. The enthalpy of tungsten in cal per mole between 2000° and 3600°K can be represented by the equation HºT- Hº298 = - 1.7622 X 103 + 5.7772T + 8.9861 where T is in degrees Kelvin. A tabulation of com -puted values is presented for heat capacity, entropy, and free energy function. A drop calorimeter has been constructed to carry out enthalpy measurements at temperatures to 3600°K. Samples are heated by induction1 and dropped into a commercial adiabatic calorimeter, modified for this purpose. The experimental temperature is limited by the melting point of container materials and compatibility of the container and its contents. Several high-temperature drop calorimeters have been described in the literature1-5 but none has been used at temperatures as high as those in the present work; our measurements of the enthalpy of tungsten range from 2800" to 3600°K. DESCRIPTION OF EQUIPMENT An overall schematic view of the equipment is shown in Fig. 1. Power for the induction coil is supplied by a 25-kw 250 kHz Ther-Monic generator coupled to an iron core RF transformer. The Sample capsule is suspended in the work coil by 10-mil diam tungsten wires which are wrapped around a horizontal 5-mil diam tungsten wire. The horizontal suspension wire is clamped between two massive copper electrodes which are fixed in an x-y motion device that allows adjustment of the position of the heated capsule from outside the vacuum chamber. The copper electrodes are connected by flexible copper straps to a 1250-joule (5 kv, 100 pfarad) condenser bank. When it is desired to release the capsule, the condensers are discharged through the horizontal suspension wire causing it to vaporize rapidly. Very reliable and precise release of the capsule is achieved in this manner. Experiments have shown that no heat correction is required for this discharge energy. As part of the temperature measuring system, two prism holders have been incorporated in the apparatus. The upper prism holder is in the main vacuum chamber itself, whereas the lower one is in a side arm attached to the drop tube below the gate valve. The upper prism is mounted on a rotary vacuum feed-through, and may be moved under a protective shield when not in use. This prevents deposition of vapors on the prism surfaces when temperature measurements are not being made. Similarly, the lower prism is mounted on a push-pull vacuum feed-through, and when not in use may be pulled into its side tube. The prism mountings are fitted with guides and stops so that they may be moved precisely into the desired position. The aim throughout is to minimize the time the prisms are exposed to vapors from the hot samples. At the high temperatures reported in this paper, only the lower prism was used. The upper prism holder in these cases was fitted with an additional radiation shield. By using a prism and viewport, the lower surface of the samples can be observed by an optical pyrometer. The measurements discussed in this paper were obtained with a Leeds and Northrup 8622-C-S series manual pyrometer which is estimated to be accurate to 0.5 pct. Pyrometer calibrations and prism and window corrections were carried out in the conventional manner6 using tungsten strip lamps calibrated by the National Physical Laboratory, Teddington, England. Prism corrections were rechecked after each use. All work to date has been done in vacuum, and no measurable change has been observed in the prism correction below -2300°K for the upper prism and below -2800°K for the lower one. The total time of exposure of the prisms is about 50 sec per run. At high temperature, the final temperature reading is corrected by using the final A value for the prism; see Ref. 6 for details of this procedure. The calorimeter is a modified Parr Instrument Co. (Moline, lll.), Series 1230 adiabatic calorimeter with automatic jacket control. Other authors5 have used a similar calorimeter with good results. The calorimeter jacket cover and calorimeter cover are attached to the drop tube which contains a radiation shield. This shield is a gold-plated copper disc which can be operated manually from outside the calorimeter. The receiver is attached below the radiation shield and is lined with tungsten. In a typical experiment, the calorimeter and its jacket water temperatures were adjusted to 0.000°K temperature difference. The sample was allowed to equilibrate in the furnace at the desired temperature for about 20 min. The initial calorimeter temperature was then recorded, the sample dropped, and appropriate shutters closed. After about 3 min, the drop tube and receiver were filled with helium to 60 torr. The final calorimeter temperature was recorded after it had remained constant over a 5-min period. The equilibration time in the calorimeter was about 25 min. Thermistor probes are used to operate a hot and cold water supply system to maintain the jacket temperature equal to the calorimeter temperature. For actual measurements of the calorimeter temperatures, a quartz thermometer was used (Hewlett Packard Dymec Thermometer, Model #2801A). This thermome-

Jan 1, 1970

By M. Deighton, R. N. Parkins

The metals Cd, ,Wg-, Sn, TI, Zn, and Zr reach a peak hardness after a criticfir1 deformation by rolling- and then soften with fwther rolling-, thereby exhibiting wovk softening. Optical metallography on Cd, Mg, and Zn shows that work softening is accompanied by a change in grain size occurring during deformation. The creep of zinc from -1l° to +60°C at stresses in the range of 7.9 to 17.3 kg per sq mm is given by € = e0 -t- Bt + Kt +at6. The third and second rate constcints are related by the equation a = K~ K6 and their stress and temperature dependence can be represented by the equations K = A, . exp - (u, - Bu)/kT. A model based upon the stress activated glide of sub-boundaries is proposed which qualitatively accounts for the metallog-raphic observations. Expressions, which are in reasonable quantitative agreement with the ex-pe~inzental observations, are derived for the creep of zinc. THE term "work softening" has been used previously by Polakowski1 and by Cottrell and stokes2 to describe phenomena where further strain of a deformed material leads to a decrease in flow stress. In both cases, however, the conditions were changed for the second straining. Here, the term "work softening" is intended to refer to a decrease in flow stress after continued straining in the same direction at the same temperature: work softening is the antithesis of "work hardening". Work softening of zinc was reported by chadwick3 and in discussion of that paper Jenkins4 indicated that cadmium also work softens. More recently work softening has been reported5 in two magnesium alloys, -99.5 pct Mg. Chadwick found that the hardness, 0.2 pct Proof Stress and the UTS of electrolytic zinc all increased with progressive cold reductions up to 30 pct and then progressively decreased with further rolling. Gay and Kelly6 used a back-reflection X-ray technique to study the effect of cold rolling zinc and found that although deformations greater than 2 to 5 pct reduction in thickness produced some recrystallized grains, deformations greater than 40 pct caused com-plete spontaneous recrystallization. At deformations greater than 60 pct the material was found to consist solely of recrystallized grains, -20 pm diam, the size of which decreased with increasing reduction and was much less than the initial grain size of the annealed material (-300 pm diam). Similar results were also reported for cadmium, tin, and lead.6 Gay, Hirsch, and Kelly' suggest that these experiments indicate recrys-tallization takes place when the dislocation density exceeds a certain value. However, no measurements of MATERIALS AND EXPERIMENTAL PROCEDURE The purity of the metals used in this work is indicated by the following figures: Zn (99.99); Cd (99.94); Mg (99.95); T1 (99.99). The zirconium was iodide crys tal bar with a probable purity of about 98 pct. The metals were obtained in the form of 0.25 in. thick strip or 0.425 in. diam rod by various fabrication methods and then annealed to ensure complete re-crystallization. Hardness-deformation curves were obtained at room temperature by rolling 4 in. thick strip under conditions which left a surface adequate for diamond pyramid hardness tests immediately after rolling. The hardness was taken as the niean of five impressions made using a 5 kg load and the time elapsing between rolling and making the last impression never exceeded 5 min. The zinc specimens for creep testing were from 3 by 3 by 4 in. cast slabs which were rolled to 0.10 in. thickness starting at 350°C and finishing cold. The resulting strip was cut into pieces 1 in. wide and annealed in batches. With suitable choices of annealing temperature between 100" arid 400°C five different grain sizes varying from 4.54 x 10' to 3.03 x l05 grains per sq cm (530 to 20 um diam) were obtained. Creep tests were done in compression using a sub-press, based on a design after Ford,8 in which the strip is compressed between dies 0.100 in. wide under conditions of plane strain. Since there is no lateral spread of the material, the area of contact between the dies and strip remains constant throughout the test and the application of a constant load, using the load maintaining device of a hydraulic testing machine, resulted in a constant stress. Covering the dies with strips of P.T.F.E. reduced frictional effects to a minimum. The creep strain was obtained by measuring the travel of the crosshead of the testing machine to a sensitivity of 0.1 pct reduction in thickness. The complete subpress assembly was contained in a steel box and for tests above the ambient this was filled with liquid paraffin and heated electrically. Temperatures below the ambient were obtained with a cooling mixture of acetone and solid carbon dioxide in the box. The liquids were stirred and the temperature of the specimen, which was controlled to ±0.5"C dur-ing a test, was measured by a thermocouple placed near the dies. Compression testing of cylindrical specimens was also carried out in the subpress using hardened flat discs separated from the test material by P.T.F.E. sheets which obviated barrelling of the specimens. Various initial strain rates were supplied by the hydraulic testing machine, and the deformation was measured by a clock dial gage resting on the cross-

Jan 1, 1970

By Merlin H. Aylesworth

THE subject assigned to me is peculiarly appropriate to the anniversary of the birth of Abraham Lincoln. If we applied to our present problems the ideals and methods of the Great Emancipator, the future of American institutions would be so definitely assured that there would be little need to discuss the matter. The only inquiries would relate to the pace of progress, not to the possibility of progress. As a nation we have grown more and more to revere the memory of Lincoln, to honor his character, to extol his teachings and to eulogize his concepts of democracy. We rec-

Jan 1, 1940

By L., Ormsby

DRILLING and blasting practices in the Morenci open pit have undergone considerable modification in recent years. Changes in the character of the ground being mined, modifications of working conditions, and continuous experimentation have been the contributing factors.

Jan 1, 1950

By Ovid W. Eshbach

ENGINEERING education has been powerfully affected by the impact of war, just how powerfully can be better understood after considering the postwar problems regarding students, staff, and plant. In time of war no one will question the necessity of expediency of military training. With the cessation of hostilities, expediency gives way to the evolutionary process of strengthening engineering education as need is exemplified by experience. During the war, except for the Navy V-12 program, engineering education was at its lowest ebb of the century. Freshman enrollments were largely limited to those graduating from high school at the age of seventeen; and the upperclass, to those disqualified for active service. In most schools the experienced staff was either in service or government and industrial research. Many may never return to their former occupations. The most immediate problem is that of maintaining and building a staff to meet the enrollment of returning veterans. It is estimated that out of the eleven

Jan 1, 1945

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 331/3 Per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches.

Jan 1, 1947

By E. P. JENNINQS

(Cleveland meeting, October, 1912.) LARGE deposits of titaniferous iron-ore occur at Caribou, an old silver-mining camp in Boulder county, Colo., 17 miles west by south of Boulder, and a few miles northwest of the tungsten-mines. Professor Regis Chauvenet 1 published a part analysis of the ore many years ago, but gave no description of the wall-rock. Caribou hill, which contains both the silver-bearing veins and the iron-ore deposits, is a low dome of gabbro surrounded by the Archaean schists and gneisses of the Front range of the Rocky mountains, the peaks of which, a few miles west of Caribou, attain an elevation exceeding 12,000 ft. The gabbro stock is roughly elliptical in outline, with approximate diameters of 1 and 3 miles. The crest of the dome is 10,500 ft. above sea-level, and the town and ore-deposits are 500 ft. lower. Outcrops of the iron-ore occur in the town and extend NW. for 2,000 ft., where they disappear under the swampy meadows of Caribou park. Portions of the deposit are covered by drift, but one continuous outcrop is 900 ft. long and from 200 to 250 ft. wide. A second deposit is 0.25 mile south of the town along the eastern slope of the hill. It is not as well defined as the north bed, but is approximately 1,000 ft. long and from 100 to 200 ft. wide. The easily disintegrated ore does not form prominent outcrops, but the outlines of the deposits are readily traced by the large amount of ore fragments that cover the ground. Trenches and pits sunk on the outcrop expose a roughly banded magnetic iron-ore, with pyroxene as the principal gangue-mineral. The Gabbro. This rock was classified in the field as a gabbro from the presence of pyroxene and striated feldspars, and for convenience the field-name will be retained. 1 Chauvenet, Regis, Biennial Report of State School of Mines, Golden, Colo., p. 16 (1886).

Oct 1, 1912

By Carl Scholz

FROM the engineer's standpoint, labor organizations are of interest in so far as they 'affect efficiency, maximum production and unit cost, and in this respect the earlier labor organizations' which existed in the age of the Guilds were ideal, inasmuch as they stood ' for competency of the apprentice and close cooperation ' between employers and employees. In later years the tendencies of the labor organizations have gone in the opposite direction and, instead of cooperating 'with the engineer, they usually oppose him on the mistaken theory, that labor-saving devices reduce forces, and costs; in this respect, the united Mine Workers of America have been particularly active and, to a very great extent, successful.

Jan 1, 1921