Search Documents

By J. E. Burke, Y. G. Shiau

SEVERAL attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealing Two fundamentally different hypotheses have been advanced; with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary The theory of Jeffries1 that grain size and grain size contrast control growth is an example The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel3 Although it is generally stated that grain growth does not precede recrystallization, several workers4,5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some' grain boundary migration The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that-can be introduced by mechanical deformation An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used It was also planned to determine the effect of such deformation the rate of growth in a specimen which would show - growth in the unstrained condition Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures French7 has reported that at deformations less than 17 pct it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under conditions of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a small extent EXPERIMENTAL PROCEDURE The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1947

By E. W. Newman

DURING 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mined during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River, and Absarokee, on the Stillwater River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specifications as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. HISTORY OF DEPOSITS The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the first optical calcite produced from Montana came from the Cartwright deposit near Greycliff,1 but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by A. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the Montana and California deposits. This com-

Jan 1, 1945

By C. W. EICHRODT

NUMEROUS requests for the suspension of publicity make difficult the preparation of the annual review of copper metallurgy for 1934. In the United States, sales allocations indirectly have set restrictions on the scope of activities of producers and refiners, and necessitated closer cooperation between secondary and primary producers. However, the feeling exists that preparations for a return of intense competition should not he neglected, and careful investigations are being conducted for ways and means of improving industrial positions and production methods. In all probability, efficiency in technique and equipment will prove of far greater importance in the near future than production capacity, and many important developments in copper metallurgy later will be found to have been born during the current year.

Jan 1, 1935

By Malcolm F. Hawkes

AUSTENITE grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, machinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to provide knowledge of the grain-size -characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstructures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The problem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will be considered first. More than So commercially produced cast steels representing a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules; namely, one hour at 1550°F, one hour at 1700°F, and six hours at 1700°F. The list of steels and results obtained on them will be found in the appendix. (See page 21.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT METHODS SUITABLE FOR DETERMINING AUSTENITE GRAIN SIZE AFTER HEAT- TREATMENT AT ORDINARY TEMPERATURES AND TIMES It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1947

By C. L. Mantell

When considered from the viewpoint of world annual output, tin is one of the rarest metals. Its annual production is exceeded by that of iron, copper, lead, zinc. aluminum, magnesium; probably by that of the ferroalloys of manganese, chromium, and silicon, and possibly by the world production of sodium; while it exceeds only the output of such common metals as nickel, antimony, mercury, tungsten, molybdenum, silver, gold and the precious metals. Cassiterite, or tinstone, until the second World War was the only mineral that was an important source of tin. This mineral is frequently called "tin ore." The use of the term should be restricted to the ore containing the mineral, and not, in addition, to the concentrates of the mineral obtained from the ore or from stanniferous alluvial deposits. There is a general misuse of the term "tin ore" in the Malay Peninsula and adjacent localities, particularly where most of the mineral is obtained from secondary stanniferous deposits. The term "cassit-erite" is exclusively used in mineralogical, geological, and other scientific writings; it is unfortunate that it is not mole frequently used when referring to the occurrence of the mineral on an economic scale. Ores "Tinstone" js a very convenient old English term deserving a more frequent use. Tinstone is a dioxide of tin, or stannic oxide. When chemically Pure, as in the very rare transparent variety, it has a metallic content of 78.6 per cent tin. Frequently, however, the crystals and grains contain appreciable amounts of impurities, chiefly iron and tantalum. The impurities here referred to are those actually in the mineral itself. Tinstone usually has a deep brown or black color with an adamantine luster. Several other colored varieties are known, among them red ruby tin, yellow rosin tin, and yellow wax tin. the names jn each case being descriptive of the mineral's appearance. Ainalite is a variety of cassiterite con-taining almost g per cent of tantalum pentoxide. Sparable tin, tooth tin, and needle tin, as a result of their acute dite-tragonal pyramidal crystalline form, re-ceive their names from their crystallo-graphic appearance. Wood tin is a compact variety of cassiterite composed of radiating fibers resembling dry wood. Toad's-eye tin is a similar variety on a smaller scale in which the fibers appear to resemble the eye of a toad. Stream tin is water-worn tin-stone. Float tin is sometimes employed to describe the cassiterite occurring in soil derived from the weathered surface of a mineralized area. Stannite is an ore of tin of lesser impor-tance than cassiterite. It is a sulphide of tin, copper, and iron, sometimes known as tin pyrites or bell-metal ore. Its chemical com-position is sometimes expressed by the for-mula Cu,S.FeS.SnSz with zinc usually present in varying quantities. The tin con-tent varies from 22 to 27 per cent and there is about 29 per cent of copper, 13 per cent of iron, and 30 Per cent of sulphur.

Jan 1, 1944

By Cyril Wells

THE diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migra-tion of carbon in gamma iron occurs.1,2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with com-position, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schönert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By Donald A. Brobst

The minerals barite (BaSO4 barium sulfate) and witherite (BaCO3 barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1973 consumed at least 80% of the world's produc¬tion of 4.4 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The re¬maining 20% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity fill¬ing, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favor¬able for the discovery of new deposits of com¬mercial value. Witherite is much less common and abun¬dant than barite, although it is more desirable in many ways as a raw material for the pro¬duction of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir condi¬tions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemi¬cally, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite ho¬mogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber in¬dustry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and li¬noleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other sub¬stances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weight down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1975

By Walter C. Lawson

THE primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in' the Morenci open pit. GENERAL MINING OPERATIONS Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months' period (Fig I). Broken ore and waste, is loaded., into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high:. They are blasted- with churn drill holes, and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). PREPARATION OF PANEL GRADE In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many ties broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1947

By D. V. Carter, D. C. Williams

Four oil discoveries were made in east and east central Texas during 1940, three of which represented new fields. In the Chapel Hill field, Smith County, oil was found where formerly only gas and distillate were produced. The three oil fields discovered are: Hawkins, Wood County; Pittsburg, Camp County; and Tehuacana, Limestone County. Important extensions were made to the following fields: Bazette, Navarro County; Long Lake, Anderson and Leon Counties; Cayuga, Anderson, Freestone and Henderson Counties; Opelika, Henderson County; and Talco, Titus and Franklin Counties. At the close of the year 54 oil and gas fields were producing in the district. There were 13 other fields, 11 oil and 2 gas, which have been abandoned. The East Texas field led the district in the number of completions for the year. During the year about 622 wells (oil and distillate wells included) were completed and 80 wildcats were drilled. Production and Proration During the year 170,424,685 bbl. of oil (distillate production included) were produced in the district—a decrease of 2.6 per cent from the 175,053,729 bbl. (distillate production included) during the preceding year. The district's production for the year 1938 was 182,369,484 bhl. As usual, most of the district's annual production was in the East Texas field, which produced 139,095,694 bbl. (distillate production in- cluded) during 1940, or 81.6 per cent of the total oil produced as compared with 141,333,317 bbl. (80.7 per cent) for 1939. The December estimated daily average production in the district was 424,565 bbl. The district accounted for 34.9 per cent of the state's annual production, compared to 36.7 pcr cent of the state's 1939 production. The decrease in production for 1940 may be attributed to changes made in proration schedules. Any material changes in the district's annual production may be considered for the most part as a reflection of proration-schedule changes affecting the East Texas field, since it is by far the most important field in the area. The entire state was subject to 71 shutdown days for the year; the East Texas field to 131; and the Rodessa field (Cass County, Texas, portion) to 5 days. No important changes were made in field rules and regulations during the year regarding the allocation of oil in individual fields in this district. Discoveries The Hawkins field is in southeastern Wood County in and principally north of the town of Hawkins. Development to date indicates that the field is somewhat of an elongated anticline trending slightly east of north and the proved oil area appears at this time to cover approximately 4000 acres. The oil production has been secured from the Woodbine sand, Upper Cretaceous; a considerable quantity of gas has been encountered in the Sub-Clarksville formation (Eagleford shale) in the higher part of the structure. It appears that a free gas

Jan 1, 1941

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By D. C. Williams, D. V. Carter

Four oil discoveries were made in east and east central Texas during 1940, three of which represented new fields. In the Chapel Hill field, Smith County, oil was found where formerly only gas and distillate were produced. The three oil fields discovered are: Hawkins, Wood County; Pittsburg, Camp County; and Tehuacana, Limestone County. Important extensions were made to the following fields: Bazette, Navarro County; Long Lake, Anderson and Leon Counties; Cayuga, Anderson, Freestone and Henderson Counties; Opelika, Henderson County; and Talco, Titus and Franklin Counties. At the close of the year 54 oil and gas fields were producing in the district. There were 13 other fields, 11 oil and 2 gas, which have been abandoned. The East Texas field led the district in the number of completions for the year. During the year about 622 wells (oil and distillate wells included) were completed and 80 wildcats were drilled. Production and Proration During the year 170,424,685 bbl. of oil (distillate production included) were produced in the district—a decrease of 2.6 per cent from the 175,053,729 bbl. (distillate production included) during the preceding year. The district's production for the year 1938 was 182,369,484 bhl. As usual, most of the district's annual production was in the East Texas field, which produced 139,095,694 bbl. (distillate production in- cluded) during 1940, or 81.6 per cent of the total oil produced as compared with 141,333,317 bbl. (80.7 per cent) for 1939. The December estimated daily average production in the district was 424,565 bbl. The district accounted for 34.9 per cent of the state's annual production, compared to 36.7 pcr cent of the state's 1939 production. The decrease in production for 1940 may be attributed to changes made in proration schedules. Any material changes in the district's annual production may be considered for the most part as a reflection of proration-schedule changes affecting the East Texas field, since it is by far the most important field in the area. The entire state was subject to 71 shutdown days for the year; the East Texas field to 131; and the Rodessa field (Cass County, Texas, portion) to 5 days. No important changes were made in field rules and regulations during the year regarding the allocation of oil in individual fields in this district. Discoveries The Hawkins field is in southeastern Wood County in and principally north of the town of Hawkins. Development to date indicates that the field is somewhat of an elongated anticline trending slightly east of north and the proved oil area appears at this time to cover approximately 4000 acres. The oil production has been secured from the Woodbine sand, Upper Cretaceous; a considerable quantity of gas has been encountered in the Sub-Clarksville formation (Eagleford shale) in the higher part of the structure. It appears that a free gas

Jan 1, 1941

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By C. O. Tarr, G. V. Smith, R. F. Miller

METALLURGISTS have long recognized that the Fe3C type of carbide is not a stable phase in steel and that, given sufficient time, it will decompose with formation of graphite, at least at temperatures below about 2050°F.1 This slow graphitization has never been of much concern to users of hypoeutectoid steels, for in such steels it occurs only during prolonged exposure at elevated temperature. In 1935, Kinzel and Moore2 reported complete graphitization of the carbide of a 0.1 5 per cent carbon steel that had been in senrice for about 26,000 hr. at a temperature of about 1100° to 1200°F. In discussing this paper, both Mathews and Sauveur reported graphitization of slightly hypereutectoid steels. In an extensive investigation of graphitization of high-purity iron-carbon alloys, Wells1 produced graphite at 7o0°C. (1290°F.) in an alloy containing as little as 0.13 per cent carbon, and showed that graphite may precipitate either directly from austenite or from decomposition of Fe3C, also that the rate of graphitization tends to increase with increase of temperature, at least up to a certain point, and with the presence of graphite nuclei. Jenkins, Mellor and Jenkinson,3 studying the structural changes in carbon steels ranging from 0.17 to 1.14 per cent carbon during stress-rupture tests at elevated temperature, obsenred graphite in an aluminum-killed 0.40 per cent carbon steel after fracture in 4340 hr. under a stress of 17,900 lb. per sq. in. at 840°F. and in many of the steels after stress-rupture test at 1200°F. Unstressed samples of 0.60, 0.86 and 1.14 per cent carbon steels graphitized almost completely in 360 hr. at 1200°F., while samples of 0.90 and 1.10 per cent carbon steels were somewhat graphitized, and steels containing 0.24, 0.40 and 0.57 per cent carbon showed no sign of graphite. Their results indicate that graphite precipitates the more readily the higher the carbon content, though this tendency is influenced to some extent by deoxidation practice, and that graphitization is accelerated by plastic deformation. In a recent study of the graphitization of 0.4 and 0.6 per cent carbon steel strip, made by M. A. Hughes,4 it was found that at 1200°F. graphite appeared after 72 hr. in aluminum-killed but not in silicon-killed steel, and that the rate of graphitization was increased by slow cooling from 1600°F. and by cold-working prior to annealing. In creep tests of normalized o. I 5 per cent carbon steel killed with 2.5 lb. of aluminum per ton, at the U. S. Steel Corporation laboratory at Kearny, spheroidization and some graphitization were found after 3000 hr. at 1000°F. under a stress as low as 15m lb. per sq. inch.

Jan 1, 1944

By G. V. Smith, C. O. Tarr, R. F. Miller

Metallurgists have long recognized that the Fe3C type of carbide is not a stable phase in steel and that, given sufficient time, it will decompose with formation of graphite, at least at temperatures below about 205o°F.l This slow graphitization has never been of much concern to users of hypoeutectoid steels, for in such steels it occurs only during prolonged exposure at elevated temperature. In I935, Kinzel and Moore2 reported complete graphitization of the carbide of a 0. I5 per cent carbon steel that had been in service for about 26,000 hr. at a temperature of about IIOO° to 12oo°F. In discussing this paper, both Mathews and Sauveur reported graphitization of slightly hypereutectoid steels. In an extensive investigation of graphitization of high-purity iron-carbon alloys, Wells1 produced graphite at 7oo°C. (I29o°F.) in an alloy containing as little as 0.13 per cent carbon, and showed that graphite may precipitate either directly from austenite or from decomposition of Fe3C, also that the rate of graphitization tends to increase with increase of temperature, at least up to a certain point, and with the presence of graphite nuclei. Jenkins, Mellor and Jenkinson,3 studying the structural changes in carbon steels ranging from 0.17 to 1.14 per cent carbon during stress-rupture tests at elevated temperature, observed graphite in an aluminum-killed 0.40 per cent carbon steel after fracture in 4340 hr. under a stress of 17,900 lb. per sq. in. at 840°F. and in many of the steels after stress-rupture test at 12oo°F. Unstressed samples of 0.60, 0.86 and I.I4 per cent carbon steels graphitized almost completely in 360 hr. at I200°F., while samples of 0.90 and 1.10 per cent carbon steels were somewhat graphitized, and steels containing 0.24, 0.40 and 0.57 per cent carbon showed no sign of graphite. Their results indicate that graphite precipitates the more readily the higher the carbon content, though this tendency is influenced to some extent by deoxidation practice, and that graphitization is accelerated by plastic deformation. In a recent study of the graphitization of 0.4 and 0.6 per cent carbon steel strip, made by M. A. Hughes,4 it was found that at I2oo°F. graphite appeared after 72 hr. in aluminum-killed but not in silicon-killed steel, and that the rate of graphitization was increased by slow cooling from I6oo°F. and by cold-working prior to annealing. In creep tests of normalized 0.15 per cent carbon steel killed with 2.5 Ib. of aluminum per ton, at the U. S. Steel Corporation laboratory at Kearny, spheroidization and some graphitization were found after 3000 hr. at Iooo°F. under a stress as low as 1500 lb. per sq. inch. .

Jan 1, 1944

By C. O. Tarr, G. V. Smith, R. F. Miller

Metallurgists have long recognized that the Fe3C type of carbide is not a stable phase in steel and that, given sufficient time, it will decompose with formation of graphite, at least at temperatures below about 205o°F.l This slow graphitization has never been of much concern to users of hypoeutectoid steels, for in such steels it occurs only during prolonged exposure at elevated temperature. In I935, Kinzel and Moore2 reported complete graphitization of the carbide of a 0. I5 per cent carbon steel that had been in service for about 26,000 hr. at a temperature of about IIOO° to 12oo°F. In discussing this paper, both Mathews and Sauveur reported graphitization of slightly hypereutectoid steels. In an extensive investigation of graphitization of high-purity iron-carbon alloys, Wells1 produced graphite at 7oo°C. (I29o°F.) in an alloy containing as little as 0.13 per cent carbon, and showed that graphite may precipitate either directly from austenite or from decomposition of Fe3C, also that the rate of graphitization tends to increase with increase of temperature, at least up to a certain point, and with the presence of graphite nuclei. Jenkins, Mellor and Jenkinson,3 studying the structural changes in carbon steels ranging from 0.17 to 1.14 per cent carbon during stress-rupture tests at elevated temperature, observed graphite in an aluminum-killed 0.40 per cent carbon steel after fracture in 4340 hr. under a stress of 17,900 lb. per sq. in. at 840°F. and in many of the steels after stress-rupture test at 12oo°F. Unstressed samples of 0.60, 0.86 and I.I4 per cent carbon steels graphitized almost completely in 360 hr. at I200°F., while samples of 0.90 and 1.10 per cent carbon steels were somewhat graphitized, and steels containing 0.24, 0.40 and 0.57 per cent carbon showed no sign of graphite. Their results indicate that graphite precipitates the more readily the higher the carbon content, though this tendency is influenced to some extent by deoxidation practice, and that graphitization is accelerated by plastic deformation. In a recent study of the graphitization of 0.4 and 0.6 per cent carbon steel strip, made by M. A. Hughes,4 it was found that at I2oo°F. graphite appeared after 72 hr. in aluminum-killed but not in silicon-killed steel, and that the rate of graphitization was increased by slow cooling from I6oo°F. and by cold-working prior to annealing. In creep tests of normalized 0.15 per cent carbon steel killed with 2.5 Ib. of aluminum per ton, at the U. S. Steel Corporation laboratory at Kearny, spheroidization and some graphitization were found after 3000 hr. at Iooo°F. under a stress as low as 1500 lb. per sq. inch. .

Jan 1, 1944

Jan 1, 1906

By Charles Behre

THIS paper deals with recent geologic studies in the slate belt of Northampton, Lehigh and Berks counties, Pennsylvania. The work was conducted under the auspices of the Pennsylvania Topographic and Geologic Survey. Three years have now been spent in detailed consideration of the economic geology of this region. In the field, particular attention was paid to the bearing of geology on quarry development and property valuation and the object of this paper is to summarize the results from that viewpoint. Excellent studies of a somewhat similar nature have already been carried out by Bowles,1 but with the emphasis upon the details of quarrying and fabricating methods, rather than upon the geologic relations. THE NORTHAMPTON-LEHIGH-BERKS DISTRICT Location The region here discussed lies in east-central Pennsylvania and extends southwestward from Delaware River, on the New Jersey line, to the Schuylkill in north-central Berks County. It is an elongated belt occupying the northern sections of the three counties mentioned and lying along the southern edge of Blue Mountain. Its length is about 50 miles and its average width five or six, though in places it attains a maximum of 10 miles.

Jan 1, 1928

A comprehensive, systematically structured mineral evaluation system is a prime requirement for objectively assessing mineral supply impacts on the economy. The Minerals Availability System developed by the US Bureau of Mines is a step in the right direction-a well-organized unraveling of the mineral supply network, structured in format to allow quick retrieval for rapid listing, supply analysis, and other uses.

Jan 9, 1977

By H. W. Becker, C. C. Frye, A. V. Degau, A. Masuda

Natural gas containing 25.65 per cent hydrogen sulfide and 4.75 per cent carbon dioxicle is gathered frorn eight \veih arid tratzsporrcd 26 miles at a flow rate of 160 MMcf/D and at operating pressures of frotrl 1,200 to 1,800 psig. Dry desiccant dehydrators at each wellsite tnaintaitz the dew point of the gas below 17F. Telemetering facililies permit control of field operations from a central instrunlent console. Corrosion control ineasures, design coilsiderations and material specifications pertainitz to these specia1 conditions are cliscussed. INTRODUCTION Natural gas containing 25.65 per cent H2S and 4.75 pcr cent CO, is produced from the Pine Creek field, Alta. It is dehydrated at wellheads, gathered at 2.200 psig and transported 26 miles to the Windfall field where it is delivered to the inlet of injection compressors at 1,800 psig. The daily average volume of gas transported is 160 MMcf. The project is believed to be unique in its combination of percentage of hydrogen sulfide, operating pressure and transportation distance. This paper describes the project and presents details of some of the design features, corrosion control program and centralized automatic operational control. The Pine Creek field project is one phase of a joint operation of two fields—thc other being the Windfall field. The two fields lie about 30 miles north of Edson, Alta. and 20 miles west of Whitecourt, Alta., respectively, as shown on the map (Fig. 1). They are owned by the same interests and operated according to a plan for maximum economic recovery of products. The Windfall Leduc D-3 reservoir contains a rich condensate-bearing gas containing 15.5 per cent HIS. The gas from the Pine Creek field contains only very small quantities of butane and heavier products. The Windfall reservoir is being cycled to obtain maximum condensate recovery using gas from the Pine Creek field as the displacing fluid, while producing the residue sales gas for both fields from the Windfall field. The Pine Creek field development and gas-gathering facilities are shown on the map (Fig. 2). The producing formation is the Leduc D-3 reef at a depth of 11,300 ft. The original reservoir pressure was 4,590 psia at 7,400 ft subsea and the temperature is 245F. Eight wells are equippcd with dry desiccant dehydrators with the following capacity ratings: three at 35 MMcf/D; three at 20 MMcf/D; and two at 10 MMcf/D. WELLHEAD EQUIPMENT Dry desiccant dehydrators were designed to reduce the water content of the saturated wellhead stream to 2.5 lb of water/MMcf at 2,000 psig. This specification was necessary to prevent hydrates and corrosion forming in the pipeline which will operate at temperatures as low as 20F. A typical flow diagram is shown in Fig. 3, and Fig. 4 is a photograph of one of the wellhead installations. Some of the design details given below are subject to modification in the field. The well-stream flowing temperatures range from 135 to 170F. Wellhead flowing pressures up to 3,200 psig are reduced to the dehydrator-operating pressure of about 2,100 psig by throttling through a pressure control valve. The gas is then passed through an aerial cooler where its temperature is reduced to 105F. thus removing over half

By Young C. Kim, Francis Martino, Ish Chopra

For the past two and one-half years, various emission control strategies were jointly developed by the University of Arizona and the Homer City Owners to com- ply with the clean air requirements at its Homer City Power Plant. Some of the available options for the SO2 emission control by the Homer City Owners were:l)cleaning of run-of-mine coal,2) scheduling of mining operations at its captive mines, 3) blending the captive mine coal with externally purchased low sulfur coa1,and 4) placing a partial FGD system. This paper describes two specific emission control strategies developed and implemented. These are: 1) production scheduling at the mining face to minimize sulfur variability, and 2) external purchasing of low sulfur coal for further blending. The main objective of this paper is to share our experiences on implementing the developed strategies. This paper emphasizesthe need for proper mine planning on a short-term basis, if the power plant is to meet the desired objective.

Jan 1, 1983