Search Documents

By ROY BERENTZ

MANUFACTURE is the transformation of material by the application of energy and power. The energy of a man exerted throughout a day is equivalent to about one horsepower-hour of mechanical work an amount which can be purchased for less than 2c. It is evident that manual labor is uneconomical if mechanical energy can be applied effectively, or without disproportionate expense. Since manual energy is relatively so costly, economy demands that mechanical power be employed so as to reduce the human effort connected with mining operations to a minimum. Power, like other commodities, is most efficiently produced in large quantities. Mechanical transmission, once prevailing, is being rapidly superseded by electric drive. There are many reasons for this change; such as increased production, ease and accuracy of control, convenient application, ease of moving, etc.

Jan 1, 1930

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff" backfill to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

By Oscar A. Glaeser

MINE VENTILATION is an important factor in mine maintenance as well as having direct bearing on labor efficiency. Effective ventilation systems are costly, especially those for the deeper mines, but with intelligent direction the worth of a system is usually greater than its cost. In most mines using mechanical ventilation, and practically all deep mines, it has been found beneficial to equipment, timber, and the ground, to run the fan or fans continuously even though production has been curtailed or entirely suspended. Therefore, economies in ventilation may be overlooked when general cost reductions are necessary. The operating costs of a well-designed ventilation system should be capable of reduction during periods of curtailed or suspended operations. A mine that is ventilated by splits, or that can be sectionized, can reduce its fan-power costs considerably, and provisional divisions can sometimes be made in other mines, in which the air is ordinarily coursed through all the workings, without harmful effects.

Jan 1, 1932

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By E. R. Johnson

The copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the westem flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past I5 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7½ gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by I-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55½-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73½-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bill serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 13/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7½ McCully gyratory crusher set at 13/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73½ by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1949

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By Nicholas J. Grant, W. Michael Yim

The creep-rupture properties of nickel, in as-prestrained or prestrain-polygonized condition, were studied at 1300°F and 4000 psi, and also at 700°F and 26,000 psi. An improvement of strength was noted in both the as -prestrained and the prestrain-polygonized tests at each temperature. The as-prestrained tests, however, showed superior creep resistance to the prestrain-polygonized ones. From the results of X-ray and etch-pit studies, the strengthc gain was interpreted in terms of dislocation density and the stability of preformed substructures. COLD work is known to improve the strength properties of metals at low temperatures. At high temperatures, however, the strength improvement is often lost if gross structural changes, such as re-crystallization, take place prior to or during the test. Even in the absence of recrystallization, a prestrained metal may undergo structural changes— polygonization and the formation of well-defined subgrains—which importantly effect the resultant properties. The relationship between substructure and creep properties has received considerable attention in recent years. The work of wood1 indicated that the creep strength of aluminum and its alloys was closely related to the subgrain size. Hazlett and Hansen,2 and Ancker, Hazlett, and parker,3 working with nickel and nickel alloys, had shown that small amounts of prestrain at room temperature followed by a recovery anneal at 800°C (1470°F) improved the strength at both low and high temperatures. The strength gain was attributed to an increase in the number of subgrain boundaries as a result of the prestrain-polygonization treatment. More recently Coldren and Freeman4 studied the effect of substructures on the creep rate of nickel at 1550°F. Their conclusions indicated that the substructure size as measured by the number of boundaries was the factor that controlled the creep rate. In addition, the perfection of the subgrain boundary has been indicated to have an important role on the strength.' On the other hand, there are data which disagree with the above observations. Grant, Chaudhuri, Silver, and Ganow6 found no creep strength improvement by a prestraining treatment. In reviewing the role of subgrains on high-temperature creep, Shepard and Dorn7 concluded that the contribution of the subgrains to high-temperature creep strength was a minor one. Guard,8 in a recent study on poly-gonized nickel, has cast doubt on the validity of the postulate that subgrain size controls the creep rate. In the majority of the previous studies, the subgrain boundaries have been singled out as the most important factor in determining creep strength; however, there is no firm theoretical ground for the postulate that the subgrain boundaries act as effective barriers to dislocation motion.B910 Little effort has been directed toward the study of the relationship between creep strength and other structural variables, such as dislocation density, lattice strain,

Jan 1, 1963

By H. B. Pulsifier

The following report on the structure of copper is the result of work done in the laboratory of the Rome Wire Co. early in 1925. Previous work had indicated to the author that excellent results might be expected if a suitable technique in surfacing and etching could be developed. The resources of the Rome Wire Co. enabled this metal to be studied more intensively than previously, although none of the materials were investigated exhaustively. The material presented is hardly more than a preliminary summary of the most obvious character of the metal; a much longer research would have been necessary to solve many of the pressing problems connected with the casting and working of copper. The Rome Wire Co. has generously released the paper; to Dr. E. H. Darby, technical supervisor of the company, are due particular thanks for his appreciation of the importance of metallographic study of copper and for his effective support in the prosecution of the work and in making its publication possible. Dendrites, Cells and Granules The microscope reveals at least three orders of structural units in copper, as in other metals. The largest structural units are the dendrites —spine-shaped crystals building up the masses of metal when it solidifies from a melt or is crystallized from solutions by chemicals or electricity. The nucleus cells, commonly called "grains," are the largest and most conspicuous units of recrystallized solid metal; the limitations of their growth usually confine their sizes to microscopic proportions, although in "single crystals" they may become as large as the piece of metal itself. The granules are the microscopic fine-structural blocks or laminations that build up the nucleus cells; they are revealed when metal is etched with suitable chemicals. The granules are commonly visible at 500 diameters magnification and are plainly visible at 1000 diameters; magnification of the granular surfaces up to 6000 to 9000 diameters shows no finer units, not because of lack of optical resolution but because the chemical attack has left an unfeatured smooth surface.

Jan 1, 1926

By Daniel Bloomfield

ONE of the major problems of management is how to restore in some measure the personal relation-ship between employer and employed which, in the days of small concerns, meant better morale among employees. The complexity of industry today, the heterogeneous mass. of workers employed, many .of them new to this country and to its institutions, the inability of those whose task it is to get out production to spend much time on the problems of labor-all these and many other factors serve to make of great impor-tance the question of how to establish more satisfactory mutual good will. While there is no such thing as a sure cure for labor troubles, in spite of the fact that charlatans have been selling alleged cures to guileless employers, study and experience have brought to light methods of approach to the problems confronting management in its relation to labor that are well worth consideration. Labor problems must be approached with common sense and an open mind. Facts must be the basis of action. So it is with the question of morale in industry. What makes or breaks morale? What are the forces behind the actions of men? What is there in one man that makes him act differently from another man under similar circumstances? How are men affected by the actions of others in their own group or by the actions of those under whose supervision they work? These are questions that must be carefully studied if we are, to get at the bottom of industrial unrest. It is an easy thing to say that good will can be created by "treating men right." That involves so many things and points of view that it will hardly serve as a full answer to our problem; but it is a good starting point if we mean by right treatment the payment of wages consistent with the well being of the worker and his family as members of the community, and if we also mean the provision of sanitary, wholesome working conditions and a working schedule that does not overtax the worker physically, and mutuality-a give and take relationship. With this as a basis we can go a step farther and see what else can be done to promote better relations between management and the workers.

Jan 9, 1922

By A. B., Sabin

THERE are many who know The Lucky Tiger and will remember the 35-mile road from Esqueda, a station on The Nacozari Railroad in northern Sonora, Mexico. They will remember the box canyons of the Agua Caliente Mountains which are scarcely wide enough for two cars to pass; the Bavispe River which one hour may be a lazy trickle and the next a sweeping torrent, and the tortuous road up Tigre and Espuela canyons, now following the wash, now hugging some gigantic red cliff. It is still the same. From camp the view of the distant blue-gray mountains is the same. But one thing a visitor of a former day might miss: The hundreds of pack mules and burros, loaded with concentrates from the mill, which used to take most of the road and show up at the most inopportune places, have almost disappeared, replaced of course by the auto truck.

Jan 1, 1929

By William Brewster

DATING back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus con-tent, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/16-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

By Warren B. Weeks

The year 1940 saw an increase of 20 per cent in oil production over the previous year—compared with a 16 per cent increase the previous year. In all, 25,790,380 bbl. were produced, an increase of 4,414,150 bbl, over 1939 and the largest production figure for south Arkansas since 1928. The older settled production continued to decline. Magnolia accounted for most of the increase, with aid from the other recent deep fields. During the year, 169 wells were drilled, 79 fewer than in the previous year. Of 131 wells drilled in proven fields, 18 were dry. Three of the 38 wildcats were pool openers. The drilling depth record was increased from 9028 to 9550 feet. Trend of Prospecting For the first time since 1936, the search for oil in the deep Smackover limestone slackened perceptibly; g dry wildcats ended in Smackover, 2 in. the underlying Eagle Mills; 7 penetrated Paleozoic beds, while 9 ended in Hosston, 2 in Glen Rose, 2 in Paluxy and 4 in Gulf. Geology The wells listed in Table 2 either resulted in the discovery of new oil pools or, because of their depth or location, afforded impor-tant stratigraphic or structural informa-tion. Fig. I is a general columnar and stratigraphic section showing the relation-ship of the strata within the Comanche series. The nomenclature shown was ac-cepted by the Shreveport Geological Society. It was subsequently published by Imlay,l who indicated probable correlations with other areas and presented evidence for the possible Jurassic age of the under-lying Cotton Valley and Smackover formations. New Fields Pouke.—On June 10, 1940, the Louark Producing Co. completed its No. I Sturgis, sec. I, T. 17 S., R. 27 W., in central Miller County, producing between 3583 and 3607 ft. in the upper part of the Paluxy forma-tion. The well flowed I00 bbl. of 3r.4' gravity oil per day through Ns-in. tubing choke. This discovery resulted from seismograph work. Six other wells were drilled in the area, none of which found production in the original sand. One of these wells is producing from a sand 50 ft. deeper in the section. The others were abandoned. No further development is in prospect. Production is from lenticular sands of the upper Paluxy; 45,556 bbl. had been pro-duced by the end of 1940. There is structural closure against a fault to the northwest. McKanzie.—The Atlantic Refining Com-pany's No. I Bodcaw Lumber Co., sec. 29, T. 17 S., R. 23 W., eastern central La-fayette County, was completed June 8, 1940, as the eighth and farthest west of the Smackover (Reynolds o6lite) limestone pools. The well flowed 10 bbl. an hour of 58.6' gravity distillate through an 1 1/64 Ma-in. tubing choke, with a gas-oil ratio of 8400:I.

Jan 1, 1941

By William H. Spice

The area on which oil and gas development is reported covers 30 counties, which are included in the Texas Railroad Commission's District No. I. This area not only includes the old established Balcones fault-line group of producing fields but also includes the southwest extension of this trend and some of the deeper Wilcox (Eocene) exploratory development. (Fig. J.) In the old Balcones fault-line zone, three new fields were discovered during 1941. These fields are comparatively small, producing from Dale limestone or Austin chalk. No new fields were discovered during the year in the Edwards (Lower Cretaceous) limestone horizon. One new shallow field was discovered in the Reklaw (Eocene) sand horizon and, in the southwestern part of the district, one oil field and one gas field were discovered in the Navarro (Upper Cretaceous) sand horizon. An extremely important extension was made to the one producing Wilcox (Eocene) field of the district in the Washburn Ranch field of La Salle County. The district produced 6,650,357 bbl. during 1941, which was a 12 per cent decrease under production for 1940. Approximately 4,954,000 bbl. of this total production was produced by the three Edwards limestone fields, Luling, Salt Flat and Darst Creek, the remaining production coming from the other 43 active fields in the district. In all, 3694 wells were producing at the end of 1941, compared with 3559 wells at the end of the previous year. During the year, 139 new producing wells were completed and 29 wells were abandoned in the producing fields. The increase in producing wells represents an increase in new wells over abandonments in these fields, together with a decrease in wells temporarily shut down as of the end of 1941. The majority of production drilling was carried on in the following fields; Bee Creek, Chicon Lake, Elm Creek, Gas Ridge, Pearsall and Tenney Creek. Approximately 250 wells were drilled during 1941, of which 110 were exploratory wells completed as failures throughout the district. Considerable exploratory work was continued during 1941 along the Wilcox trend. Geophysical work employing various types of geophysical methods and leasing activity was continued along this trend, particularly by the major companies. The significance of this activity is apparent from the successful extension and development in the Washburn field of La Salle County, where several well-developed gas-and-oil producing horizons have been developed in the lower Wilcox section between 5100 and 5600 ft. as noted in the following paragraphs. Continued exploratory activity along this general trend as far as present conditions will permit is predicted for 1942. New Fields Elgin Field, Bastrop County.—No. I-A Hiram Walker, Marts and Beaven, Inc., discovery well of the Elgin field, was com pleted on Apr. 22, 1941, in broken Austin chalk from 2820 to 2840 ft., pumping 105 bbl. per day, 36.8°A.P.I. gravity. The well apparently is producing from a crevice in

Jan 1, 1942

By Warren B. Weeks

The year 1940 saw an increase of 20 per cent in oil production over the previous year—compared with a 16 per cent increase the previous year. In all, 25,790,380 bbl. were produced, an increase of 4,414,150 bbl, over 1939 and the largest production figure for south Arkansas since 1928. The older settled production continued to decline. Magnolia accounted for most of the increase, with aid from the other recent deep fields. During the year, 169 wells were drilled, 79 fewer than in the previous year. Of 131 wells drilled in proven fields, 18 were dry. Three of the 38 wildcats were pool openers. The drilling depth record was increased from 9028 to 9550 feet. Trend of Prospecting For the first time since 1936, the search for oil in the deep Smackover limestone slackened perceptibly; g dry wildcats ended in Smackover, 2 in. the underlying Eagle Mills; 7 penetrated Paleozoic beds, while 9 ended in Hosston, 2 in Glen Rose, 2 in Paluxy and 4 in Gulf. Geology The wells listed in Table 2 either resulted in the discovery of new oil pools or, because of their depth or location, afforded impor-tant stratigraphic or structural informa-tion. Fig. I is a general columnar and stratigraphic section showing the relation-ship of the strata within the Comanche series. The nomenclature shown was ac-cepted by the Shreveport Geological Society. It was subsequently published by Imlay,l who indicated probable correlations with other areas and presented evidence for the possible Jurassic age of the under-lying Cotton Valley and Smackover formations. New Fields Pouke.—On June 10, 1940, the Louark Producing Co. completed its No. I Sturgis, sec. I, T. 17 S., R. 27 W., in central Miller County, producing between 3583 and 3607 ft. in the upper part of the Paluxy forma-tion. The well flowed I00 bbl. of 3r.4' gravity oil per day through Ns-in. tubing choke. This discovery resulted from seismograph work. Six other wells were drilled in the area, none of which found production in the original sand. One of these wells is producing from a sand 50 ft. deeper in the section. The others were abandoned. No further development is in prospect. Production is from lenticular sands of the upper Paluxy; 45,556 bbl. had been pro-duced by the end of 1940. There is structural closure against a fault to the northwest. McKanzie.—The Atlantic Refining Com-pany's No. I Bodcaw Lumber Co., sec. 29, T. 17 S., R. 23 W., eastern central La-fayette County, was completed June 8, 1940, as the eighth and farthest west of the Smackover (Reynolds o6lite) limestone pools. The well flowed 10 bbl. an hour of 58.6' gravity distillate through an 1 1/64 Ma-in. tubing choke, with a gas-oil ratio of 8400:I.

Jan 1, 1941

By William H. Spice

The area on which oil and gas development is reported covers 30 counties, which are included in the Texas Railroad Commission's District No. I. This area not only includes the old established Balcones fault-line group of producing fields but also includes the southwest extension of this trend and some of the deeper Wilcox (Eocene) exploratory development. (Fig. J.) In the old Balcones fault-line zone, three new fields were discovered during 1941. These fields are comparatively small, producing from Dale limestone or Austin chalk. No new fields were discovered during the year in the Edwards (Lower Cretaceous) limestone horizon. One new shallow field was discovered in the Reklaw (Eocene) sand horizon and, in the southwestern part of the district, one oil field and one gas field were discovered in the Navarro (Upper Cretaceous) sand horizon. An extremely important extension was made to the one producing Wilcox (Eocene) field of the district in the Washburn Ranch field of La Salle County. The district produced 6,650,357 bbl. during 1941, which was a 12 per cent decrease under production for 1940. Approximately 4,954,000 bbl. of this total production was produced by the three Edwards limestone fields, Luling, Salt Flat and Darst Creek, the remaining production coming from the other 43 active fields in the district. In all, 3694 wells were producing at the end of 1941, compared with 3559 wells at the end of the previous year. During the year, 139 new producing wells were completed and 29 wells were abandoned in the producing fields. The increase in producing wells represents an increase in new wells over abandonments in these fields, together with a decrease in wells temporarily shut down as of the end of 1941. The majority of production drilling was carried on in the following fields; Bee Creek, Chicon Lake, Elm Creek, Gas Ridge, Pearsall and Tenney Creek. Approximately 250 wells were drilled during 1941, of which 110 were exploratory wells completed as failures throughout the district. Considerable exploratory work was continued during 1941 along the Wilcox trend. Geophysical work employing various types of geophysical methods and leasing activity was continued along this trend, particularly by the major companies. The significance of this activity is apparent from the successful extension and development in the Washburn field of La Salle County, where several well-developed gas-and-oil producing horizons have been developed in the lower Wilcox section between 5100 and 5600 ft. as noted in the following paragraphs. Continued exploratory activity along this general trend as far as present conditions will permit is predicted for 1942. New Fields Elgin Field, Bastrop County.—No. I-A Hiram Walker, Marts and Beaven, Inc., discovery well of the Elgin field, was com pleted on Apr. 22, 1941, in broken Austin chalk from 2820 to 2840 ft., pumping 105 bbl. per day, 36.8°A.P.I. gravity. The well apparently is producing from a crevice in

Jan 1, 1942

By A. C. Veatch

Jan 1, 1921

By AIME AIME

Adjustable Pyrometer-Stand. By L. W. BAHNEY, xxxvii, 33. Agency of Manganese in the Superficial Alteration and Secondary Enrichment of Gold-Deposits in the United States. By WILLIAM H. EMMONS, xlvi, 767. Application of Descriptive Geometry to Mining-Problems. By JOSEPH W. ROE, xxxix, 173. ARNOLD, C. EVERARD. The Giroux Shaft at Kimberly, Nev., xlii, 461. BAHNEY, L. W. An Adjustable Pyrometer-Stand, xxxvii, 33. BALL, SYDNEY H., and SHALER, MILLARD K. Mining-Conditions in the Belgian Congo, xxxix, 253. BEALS, ROGER L., and TWEEDY, GEORGE A. Cyanide-Plant and Practice at the Minas del Tajo, Rosario, Sinaloa, Mexico, xxxviii, 123.

Dec 1, 1910

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The technique of unidirectional solidification has been applied to the A1-AI3Ni and A1-CuAl2 ezltectic alloy systems; the controlled microstructure of A1-A3Ni consists of parallel A13Ni whiskers emhedded in an aluminum matrix while the Al-CuAl2, system solidifies as parallel alternate lamellae of aluminm and CuAl2. Mechanical tests (tension and flexure) have shown that the particle-matrix interface bond formed during unidirectional solidification allowes for efficient load transfer from the matrix to the reinforcing phase. Strength and fracture characterstics of the alloys were studied as a function of phase orientation; the tensile strength of controlled Al-Al3Ni samples was 43,000 psi (three times greater than that of as-cast specime~s). The strength of the Al-CIA2, cutectic was studied as a function of lamellae-flexure stress-axis orientation using a microbend apparatus. A twofold increase in outer fiber stress was observed as the lamellae were rotated from a position of no reinforcing (perpendicular to the stress axis) to one of maximum reinforcing (parallel to the stress axis), The brittle reinforcing constituent in each alloy (A13Ni and CuAl2) was observed to he the nucleating phase for fracture. It is to be concluded from this investigation that unidirectionally solidified eutectic alloys have a potential use as reinforcing coniposite) materials. In a recent review article, Chadwick1 has described the work of many investigators in the area of controlled solidification of binary eutectic alloys. Thus far, more than twenty eutectic alloys have been unidirectionally solidified to produce structures consisting of two phases in the form of alternating lamellae or as whiskers embedded within a continuous matrix; in either case, the phases are aligned parallel to the growth direction. In particular, Kraft and Albright2 have shown that the Al-CuA1, eutectic alloy exhibits a lamellar microstruc- ture as a result of unidirectional solidification while Lemkey, Hertzberg, and Ford3 have studied the A13Ni whisker-aluminum matrix morphology in the A1-A13Ni system. Whether these alloys could exhibit reinforcing behavior would have to depend upon the strength and volume fraction of the reinforcing phase (AI3Ni and CuA12) and the nature of the bond between the reinforcing phase and the matrix. Hertzberg and Kraft4 have shown that the interface bond between chromium whiskers and a copper matrix in unidirectionally solidified Cu-Cr is particularly good while Lemkey and Kraft5 have reported chromium-whisker tensile strengths in excess of 1,000,000 psi. However, with the chromium volume fraction being less than 2 pct, no reinforcing behavior was displayed by the Cu-Cr alloy.6 In view of the encouraging results concerning the good interfacial bond and high strength of the reinforcing phase in the Cu-Cr system and preliminary mechanical test data reported by Lemkey et al.3 for the A1-A13Ni system, the A1-CuA1, and A1-A13Ni eutectic alloys containing 50 and 10 vol pct, respectively, of the reinforcing phase give promise of possessing mechanical reinforcing behavior. Based on this premise, the objective of the investigation was to study the strength and fracture behavior exhibited by these anisotropic microstructures. EXPERIMENTAL PROCEDURE Controlled Solidification Procedure. An extensive description of the technique of unidirectional solidification has been presented elsewhere.' However, the pertinent details for each eutectic system studied are discussed below. Al-A13Ni System. Several master heats of this alloy were prepared by vacuum-induction melting in an A12O3crucible and casting in SiO2 mold or by induction melting in alumina crucibles under argon. The initial heats were prepared from 99.99 pct A1 and 99.99+ pct Ni, while later heats used 99.999+ pct A1 and 99.99+ pct Ni. Specimens of these master heats were unidirectionally solidified using induction and resistance heating sources and argon atmospheres at growth rates from 1.1 to 28.7 cm per hr. The thermal gradients in the liquid were controlled in the range of 26" to 36°C per cm for these runs. Al-CuA12 System. The master heat and controlled

Jan 1, 1965

Lieut. Louis J. Brunel, now in France, was commissioned on July 27, 1917, as Second Lieutenant in the Engineers Reserve Corps, assigned to the 7th U. S. Engineers, Dec. 10, 1917, and has been with the American E. F. since Mar. 26, 1918. He was assigned to the staff of the General commanding the 5th Field Artillery Brigade, as Engineer Officer, on Aug. 6, 1918. E. Ross Housholder writes that "the record for pontoon bridge building was broken Sept. 25, 1918, by Section A, Co. 4, 5th Engineer Officers' Training School, at Camp Humphreys, Va., of which I am a member. The time was 15 min. 11 3/5 seconds. We then proceeded to break the record for dismantling in 9 min. 57 1/5 seconds. The length of the bridge section was 200 ft. The post band was sent out to meet us, and we feel proud of this record. I have met quite a few A. I. M. E.

Jan 11, 1918

By McHenry Mosier

SUMMARY MERCURY is one of the strategic metals of which the supply has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributed substantially to increased production of mercury in the United States and to consequent accumulation of Government stocks. Other contributing factors have been higher prices for mercury and Government loans to operators. The Bureau has undertaken 13 exploration projects, 10 of which have been completed. This work has comprised 28,376 ft. of several types of drilling and 23,798 lin. ft. of surface trenching, and has indicated commercial ore containing 34,800 flasks of mercury and marginal ore containing 26,200 flasks, a total of 61,000 flasks; equivalent, respectively, to domestic production for 8 months, 6 months, and 14 months. As Government stocks are now adequate, domestic production (currently at the rate of 50,000 flasks per year) is gradually being curtailed through Government control of labor and operating supplies.

Jan 1, 1944