Search Documents

By W. R. Crane

THE effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. There is no doubt but that in time, because of failure of pillars, extensive fracturing and widespread settlement of the surface will result, particularly along the slope of Red Mountain, where mining has been under way for many years. Were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Until development openings and surface plants are transferred to Shades Valley, protection of the surface will probably not be considered imperative, as the area involved is not of particular value for agricultural or building purposes. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. The occurrence of heavy beds of strong tough materials at varying distances above the orebed make it doubtful whether any serious disturbance of the surface will be experienced at any considerable distance from the outcrop, although some settlement will probably take place. It is certain, however, that no great volume of water will enter the mines from fracturing of the Fort Payne chert bed, as this is known to be a compact and practically impervious formation beyond the leached zone. Not so much can be said, however, regarding other possible sources of water, as pervious beds and through faults that may be encountered in future mining operations.

Jan 8, 1925

By W. J. Taylor

It is, perhaps, more important to put on record the particulars of experiments that are derided failures than those that are successful, as those of the latter class are certain to live, while the former may be lost sight of in a short time, and repeated by others. TO this end, I propose to give the particulars of a straight or no-bosh furnace just tried at the Chester (New Jersey) works, which was such a decided failure as to leave no doubt of the plan being wrong, and determining the necessity of a bosh of some kind, as of old. Some experiences during the past year led me to suppose that the bosh or belly of a furnace was unnecessary, and that the contraction of the walls toward the bottom for the stock to wedge in, in its descent, facilitated dirty walls and scaffolding; hence, irregularity and high fuel. I concluded, however, that a very shallow bosh for a skew-back support to the stock would be necessary, and that the proper place for this was in the tuyere-section, beginning just below the tuyeres and ending just above them, where there is nothing in the solid state but fuel, which is consuming, and no slipping or travel of stock takes place. The cubical capacity of a furnace of this design would necessarily be much less than in the old style, unless it was made very much higher. But I assumed that the loss of room for reduction could be overcome by making the size of the ore and stone charged much smaller, so that the gases would act more quickly. The next point was, what should be the size of the shaft, crucible, tuyere-circle, and tunnel-head for a given quantity of air? My first design was 12 feet diameter of shaft for 7000 feet of air, with a 9-foot crucible and 8-foot toyere-circle. This I soon reduced to 8-foot shaft diameter, which I concluded was large enongh for economical work, if regular travel of the stock on the walls could be maintained. I consulted with a number of experienced furnacemen and furnace-engineers, and the plan was well thought of by many of them; and, as I had also some offers of financial aid from them toward the risk of trying the experiment, my firm concluded

Jan 1, 1885

By H. D. Wilde

DURING 1934 conditions in the production division of the petroleum industry were reasonably satisfactory but nevertheless a decided feeling of insecurity existed largely because of the uncertainty of controlling production to consumptive demand. Over-production, especially in the East Texas field, threatened a general collapse of crude prices but in spite of this, posted prices were high. Stimulated by the prevailing posted prices, wildcatting activities were wide-spread. Although a number of small discoveries were made, particularly in the Gulf Coast belt and Oklahoma, no fields of major importance, unless it was the Fitts pool in Southern Oklahoma, were brought in. Meanwhile, the Petroleum Division of the A.I.M.E. continued its activities. It sponsored the collection of production and geological data on both foreign and domestic fields. The data on all but a few producing districts in the world were published in the "Petroleum Development and Technology" volume of the "Transactions" and comprise one of the most complete tabula¬tions of this sort ever published. Work of this kind is being continued.

Jan 1, 1935

By Paul H. Hunt

MANY MISUNDERSTANDINGS have arisen regarding -Al the purchase by the Government of 24,000,000 oz. of domestically produced silver annually for the next four years at a price of 64 1/2c. to the producer. Some editorials have an¬nounced rather sarcastically that be¬cause of the strong western silver bloc in Congress, the Administration is paying a bonus of approximately $22,000,000 to a few large silver produc¬ers of the West, the amount being figured on the total purchase of about 100,000,000 oz. and the difference between the Government price and the world price for silver. Actually the Government will make a profit on this purchase, due to seigniorage, of something over $60,000,000. The 96,000,000 oz. of silver, for which the producers will receive approximately $62,000,000, will be produced in association with at least $100,000,000 worth of lead, zinc, copper and gold; the greater part of this $162,000,000 worth of metal will be produced at little profit to the mining companies, as will be shown later, because of the low prices for lead, copper and zinc. This amount of money will be spent largely for labor and supplies, thus greatly relieving the national burden of unemployment. Certainly, western mining, in the purchase of this silver, is not victimizing the Federal Government.

Jan 1, 1934

By D. N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in western Pennsylvania. The coal bed mined is in the Lower Freeport seam, which averaged 1.07 m (42 in.) in height locally. Drainage from the mine is about 13.25 ML/day (3.5 million gal per day) of water. This water deteriorates the mine's predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplilshed by pulling the 5.44 t (6 st) shields out under their own hydraulic power and transporting them by track 8.05 km (5 miles) to the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1985

By H. E. Cline

Solidification of Pb-Sn alloys ranging in composition from 1.2 to 56 at. pct Pb ws observed with polarized light. Lamellar structures were observed over a larger range of compositions in alloys containing excess tin than excess lead, as expected from constitutional supercooling. The occurrence of pools of supercooled liquid surrounded by lead is explained by the difficulty in nucleating tin. Cells and dendrites weve observed in tin-rich alloys. Evidence was found that the degenerate structure formed at low growth rates, the formation of faults, and abrupt changes in composition and structure can be attributed to non-steady-state growth. The apparent interface shape was observed to have deep grooves at the interphase boundaries. HUNT and Jackson have observed the shape of the interface during growth of organic eutectics. They observed the formation of lamellar faults and shape instabilities upon changes in growth rate. The lamellar structure in these organic eutectics was not restricted to the eutectic composition. Recent work by Mollard and Flemings2 indicated that Pb-Sn alloys from 12 to 26 at. pct Pb could be solidified with a lamellar or rodlike structure if a sufficiently steep temperature gradient was used at a slow growth rate. Observations of the solid liquid interface of the Pb-Sn eutectic were made by Davies3 using polarized light. Photographs were at too low a magnification to determine the interface shape, but he has concluded that tin was the leading phase. In the following experiments, solidification of a range of Pb-Sn alloys from 1.2 to 56 at. pct Pb was observed using polarized light, to determine the factors controlling stability of the lamellar structure. EXPERIMENTAL Procedure. One hundred-gram ingots of alloys prepared from 99.999 pct pure Pb and Sn were cast into graphite molds under argon. The compositions of the alloys were 1.2, 6, 12, 26, 36, 46, and 56 at. pct Pb. Two-gram pieces were melted between two cover glass slides which were squeezed into a 1-mm separation. Samples were then observed under polarized light in a hot stage shown in Fig. 1. A long working distance objective designed for viewing at 500 times was used. Photography was made difficult by the lack of illumination and contrast at these high magnifications. By using an elliptical polarization compensator, as suggested by A. Holik, the contrast and illumination could be optimized. Photographs could be taken only at slow growth rates to avoid excessive interface motion during the 15-sec exposure used. The solidification rate was varied by increasing or decreasing the power to the heater. It was found that insulation was necessary to avoid undesired growth rate fluctuations. The temperature gradient, as measured with two thermocouples 1 cm apart, was 80" ± 20°C per cm during all the experiments reported here. The advantage of this procedure is in being able to observe solidification while it is occurring. However, the observations are restricted to the glass-metal surface and may be influenced by this surface. Also, one has no knowledge of the interior of the sample, in contrast to studies of the freezing of transparent organic eutectics.' Observations. The alloy near the eutectic composition (26 at. pct Pb) solidified in a lamellar structure when the growth rate was uniform. If the growth

Jan 1, 1968

By R. M. Sellwood

The No. 4 I.S.F. Smelter Complex at the Avonmouth Works of Imperial Smelting Corporation (N.S.C.) Limited commenced operation at the beginning of 1968. The furnace rating is 120,000 tons zinc and 40,000 tons lead per annum. Zinc and lead concentrates are unloaded onto a 1,000 tons per hour capacity conveyor belt and automatically weighed and sampled before receipt into a 48,000 ton capacity raw material store. Distribution is by a reversible boom stacker into 16 x 3,000 ton bays and recovery is by a front end loader. Materials are fed to 16 proportioning bins for feeding via continuous weigh feeders to a 132 square metre effective updraught area sinter machine with a material flow rate of 240 tons per hour over the machine. The required quantity of output lump sinter at up to 800ºC is fed to 2 x 600 ton storage bins on the I.S.F. plant. By-product SO2 rich gas is fed to a conventional wet gas single stream acid plant rated at 600 tons per day utilizing a dry N.T.P. gas volume of 100,000 cubic metres per hour. The hot sinter and preheated coke (800ºC) are automatically neighed and charged to a 27.3m2 shaft area I.S.F. fitted with 2 x 5.5 m. wide lead splash condensers. Grade 4 zinc is tapped and transferred to the zinc refinery. Conventional type lead bullion and slag are tapped from the bottom of the furnace through a separation forehearth. The refinery consists of 6 lead and 3 cadmium columns to produce some 52,000 tons per annum of S.H.G. metal. S.H.G. metal and Grade 4 metal is cast into various shapes as required.

Jan 1, 1970

By Arthur Wade

During the year 1938, there was some drilling in Queensland, New South Wales and Victoria, as follows: Queens1and.—At Hutton Creek, lat. (approx.) 25° 45' S.; long (approx.) 149°, drilling was done by Drillers limited (subsidiary Oil Search) to a depth of 4688 ft., to the Lower Permian(?). There were small gas showings. The hole mas abandoned. At Mt. Bassett, lat (approx.) 26" 20' S.; long. (approx.) 149", Roma Blocks Oil Co. No Liability drilled to a depth of 4033 ft. The hole bottomed in granite. There were small showings of' oil and gas above bedrock in what may be Permian but is not yet determined. The company intends to run a formation tester. New South Wales.—At Kulnura, lat. (approx.) 33" S., long (approx.) 151°, the Kamilaroi Oil Company Ltd. (subsidiary of Oil Search Ltd.) drilled to a depth of 6293 ft. The Permian, probably Upper Marine Series, was reached. Drilling is to continue. Victoria.—At Romawi, lat. (approx) 37" 50' S., long. (approx.) 147" 45', a dry hole 3246 ft. deep bottomed in the Jurassic and was abandoned. It was drilled by the Governments of the Commonwealth and the State of Victoria. At Lakes Entrance, 1st. (approx.) 37" 50' S.; long. (approx) 748", a small showing of' oil (a few pints a day) was obtained from a well drilled 1275 It., to the Upper Oligocene-Glaucnnitc series, by the Austral Oil Drilling Syndicate, No Liability. Future Drilling Preparations is are being made by companies fur further test drilling in 1939, and the Governments of the Common wealth and the State of Victoria are continuing test holes for information only in the Gippsland district of Victoria. In Papua and New Guinea, no test drilling was done in 1938, but several companies are carrying on geological investigation and it is expected that, some test holes will be drilled during 1939.

Jan 1, 1939

By Arthur Wade

During the year 1938, there was some drilling in Queensland, New South Wales and Victoria, as follows: Queens1and.—At Hutton Creek, lat. (approx.) 25° 45' S.; long (approx.) 149°, drilling was done by Drillers limited (subsidiary Oil Search) to a depth of 4688 ft., to the Lower Permian(?). There were small gas showings. The hole mas abandoned. At Mt. Bassett, lat (approx.) 26" 20' S.; long. (approx.) 149", Roma Blocks Oil Co. No Liability drilled to a depth of 4033 ft. The hole bottomed in granite. There were small showings of' oil and gas above bedrock in what may be Permian but is not yet determined. The company intends to run a formation tester. New South Wales.—At Kulnura, lat. (approx.) 33" S., long (approx.) 151°, the Kamilaroi Oil Company Ltd. (subsidiary of Oil Search Ltd.) drilled to a depth of 6293 ft. The Permian, probably Upper Marine Series, was reached. Drilling is to continue. Victoria.—At Romawi, lat. (approx) 37" 50' S., long. (approx.) 147" 45', a dry hole 3246 ft. deep bottomed in the Jurassic and was abandoned. It was drilled by the Governments of the Commonwealth and the State of Victoria. At Lakes Entrance, 1st. (approx.) 37" 50' S.; long. (approx) 748", a small showing of' oil (a few pints a day) was obtained from a well drilled 1275 It., to the Upper Oligocene-Glaucnnitc series, by the Austral Oil Drilling Syndicate, No Liability. Future Drilling Preparations is are being made by companies fur further test drilling in 1939, and the Governments of the Common wealth and the State of Victoria are continuing test holes for information only in the Gippsland district of Victoria. In Papua and New Guinea, no test drilling was done in 1938, but several companies are carrying on geological investigation and it is expected that, some test holes will be drilled during 1939.

Jan 1, 1939

By Truman Aldrich

THE Clinton group of the Silurian holds the red or fossiliferous ore; its outcrops have been mapped by the State or U. S. Geological Survey. This group is from 100 to 500 ft. thick in Alabama. There are places where it is entirely missing (doubtless islands in the Silurian Sea). In Etowah County, in part of Greasy Cove and vicinity, the upper seam is a coral reef impregnated with the red ore; in this same county, step, faults bring up the ore in three or four separate ridges practically parallel. In Blount County and on Raccoon Mountain, the ore runs under the carboniferous rocks and outcrops in the valleys. In examining some bore holes made in drilling for oil, the writer found the Clinton group continuing under the Warrior coal field wherever the drill has gone deep enough. It demonstrates the possibility of a source for red ore not seriously thought of until lately. The following bore holes made principally for oil, given in Bulletin No. 22, Geological Survey of Alabama, show the presence of either ore or red rock, and suggest vast resources yet to be outlined and developed for ore in the future. The locations are given by number on the map. Hole No. 1 was drilled 6 miles southeast of Russellville, Franklin County, by the Woodward Oil & Gas Co. It passed through 160 ft. of Clinton, but only a small show of red ore was found at 1280-1400 feet. A test well, No. 2, drilled near Atwood, Franklin County, in section 26, township 8, range 14, penetrated the Clinton at 1608 ft. and found 38 ft. of limy red rock, also 8 ft. of some blood red ending at 1820 ft., making 46 ft. of red rock in all. It is reported that some good ore was cut through but this work was done by a churn drill. The hole was continued by diamond drill from here. At least 400 ft. of the formation was classified as Clinton.

Jan 10, 1924

LIST OF MEMBERS, ASSOCIATES AND JUNIOR ASSOCIATES ALPHABETICALLY ARRANGED ||Abad, Leopoldo F, College of Min, Univ of California Berkeley, Cal '23 ||Abarquez, Ramon F, Met, Bureau of Seience Manila, P I '24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio '21 Abbort, A N , Mines Supt , Mazapil Copper Co , Ltd Concepcion del Oro, Zacatecas, Mexieo '23 Abbott, Clarence E , Gen'l Supt , Iron Mines Div , Tenn Coal, Iron & R R Co , 1405 Minnesota Ave , Bessemer, Ala '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div Jenkins, Ky '15 Abbott, Robert R , Met Engr , Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz '23 Abeel, George H, Jr, Cons Min Engr 4812 W 17th St, Los Angeles, Cal '18 Abel, Albert E, Asst to Pres, Valley Mould & Iron Corpn Sharpsville, Pa '19 Abeloff, Miran S Address Wanted '21 Abernathy, G E, Kansas State Teachers College Pittsburg, Kans '20 Abey, Hiroshi, Min & Met Engr. Takata & Co, 2 Yeirakucho, Niehome, Kolimachi-ku, Tokyo, Japan '17 ||Aborn, Robert H 24 Groveland St, Auburndale, Mass '19 Abouchar, Sylvain Sley, Min Engr & Geol , Care of S H Sekaly, 13 Rue El Nimr, Cario, Egypt '17 Abraham, Arthur W 1828 N Alexandria Ave, Los Angeles, Cal '20 Abrahams, A. I 115 East 82nd St. New York, N Y '14 ||Abrahamson, C. Walter, Min Engr, Brule Min Co Stambaugh, Mich '21 Abrams, Charles Jackson Columbia Bldg, Spokane, Wash '21 Abrams, David H, Min Engr, S E Dickey & Co, 809-11 Johnstown Trust Bldg, Johnstown, Pa '20 Acker, E 01C, Met 128 East Washington Lane, Germantown, Philadelphia, Pa '86 Acker, William L, Diamond Drill Contractor Mears Bldg, Scranton, Pa '18 Ackerman, Ernest R, Pres Lawrenee Portland Cement Co Plainfield, Union Co, N J '15 Adachi, Jinzoo 11 Shiba Park, Shiba-Ku, Tokyo, Japan '88 Adachi, Yuich, Meeh Engr, Anzan Steel Works, Anzan, South Manchuria, China, (Via Dairen) '21

Jan 1, 1923

||Abad, Leopoldo F, College of Min, Univ of California Berkeley, Cal '23 ||Abarquez, Ramon F, Met, Bureau of Science Manila, P I '24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio '21 Abbott, A N , Mines Supt , Mazapel Copper Co , Ltd Concepcion del Oro, Zacatecas, Mexico '23 Abbott, Clarence E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co, 1405 Minnesota Ave, Bessemer, Ala '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div 'Jenkins, Ky '15 Abbott, Robert R , Met Engr, Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz '23 Abeel, George H, Jr, Cons Min Engr 4612 W 17th St, Los Angeles, Cal '18 Abel, Albert E, Asst to Pres, Valley Mould & Iron Corpn Sharpsville, Pa '19 ?Abeloff, Miran S Address Wanted '21 Abernathy, G E, Kansas State Teachers College Pittsburgh, Kans '20 Abey, Hiroshi, Min & Met Engr, Takata & Co, 2 Yeirakucho, Nechome, Kojimachi-ku,

Jan 1, 1923

By C. Richard Tinsley

Mineral economists debate whether to call the deep-ocean nodules "manganese nodules," "nickel nodules," "polymetallic nodules," or even "ferro-manganese nodules." It is nickel and copper that are generally regarded as the main targets in the nodules. Processing considerations are thought to virtually dictate that Deepsea Ventures will produce high-purity manganese metal (at least if it follows a hydrogen chloride leach), whereas other groups have been focusing on the selective extraction of copper, nickel, cobalt, zinc, and molybdenum, while rejecting manganese to tails. Solvent extraction appears to be the primary multimetal extraction technique (except for manganese). These processing considerations indicate that metal production f, or Deepsea Ventures is essentially a co- product system (manganese recovery is necessary to recycle chloride ions) while the other groups can more easily approach the metals as selective co-products (e.g. recovering nickel and copper, and rejecting cobalt). Some zinc may be produced as a co-product, as it may have to be removed in the solvent extraction process.

Jan 4, 1975

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By E. W. Davis

I . OPERATING TESTS 1. CHARACTER OF ORE UNDER INVESTIGATION On the eastern end of the Mesabi Range, in Northern Minnesota, is a large formation of siliceous rock which contains bands and fine grains of magnetite . The magnetite comprises about 35 per cent. of the rock. Fig.. 1 show's graphically that the tonnage of minus 200-mesh material produced varies directly with the tonnage fed to the mill. There is undoubtedly some limit to this relation, but there seems to be no indication of it at 18 T. per hr. Some of the conclusions drawn from this test are that: (a) The ball-mill is naturally a machine of very large capacity; (b) if it is not possible to deliver a large tonnage of original feed to the mill, a closed circuit should be provided so that the mill may crush its own oversize.

Jan 2, 1919

By Raymond B. Ladoo

NONMETALLIC minerals (excluding fuels) arid their primary products produced annual in the United States have a value in excess of one billion dollars, or more than that of the metals, yet the lack of expert knowledge of some of the fundamental technical and economic aspects of this most important and complicated business is astonishing. This paper will deal with the economics of this non- metallic mineral field-the business of making money from producing these minerals. The incentive behind all business activity in a capitalistic economy is to make money-to plan so that each dollar invested in property, plant, equipment, services, and so on will return more than a dollar plus simple interest. Of course, business has social, civic, and national duties and responsibilities, but the fulfillment of these is largely dependent upon financial success.

Jan 1, 1939

By AIME AIME

EITHER the 2300 people who came to the Annual Meeting were in a better frame of mind or they were resigned to their fate, or it was a better meeting than usual. Whatever the reason, at the 1nstitute?s 148th meeting the attendance was better than ever before, things went more smoothly than in some previous years, and complaints appear to have been almost entirely absent. Patience was sometimes reauired but. almost without exception, it was forthcorning the well-known recession seems to have given many members enough leisure time to come to the meeting without depriving them of the tangible wherewithal to come.

Jan 1, 1938

A regular general meeting of the Canadian Mining Institute will be held in Vancouver, B. C., on Nov. 26-28. The Council extends a cordial invitation to all members of the American Institute of Mining and Metallurgical Engineers to attend.

Jan 11, 1919

By M. M. Austin

PURE metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow.

Jan 1, 1930