Search Documents

By S. S. Peng, C. T. Holland

Mountain Top Removal (MTR) mining started in West Virginia nearly thirty years ago. This surface mining method can extract multiple coal seams as thin as a few inches thick with total recovery and minimum rock dilution in very steep mountainous terrain. It is highly efficient even if coal seams are in close proximity and small in aerial extent. Consequently, MTR has been widely used in the Central Appalachian Coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) for the past thirty years with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impacts on the surroundings in the history of MTR mining. However, in the past two years the debate over the MTR mining has grown quickly and in times become very intensely. This paper describes chronologically the issues raised by various parties, legal actions, its impacts on mining permit application and research projects developed to address the issues.

Jan 1, 2000

By K. G. Thorne, L. J. Cabri, L. R. Fyffe, D. R. Lentz, D. Hoy

"Mineralization at the Main zone of the Clarence Stream gold deposit in southwestern New Brunswick occurs within a parallel series of quartz veins that occupy a NE-trending, steeply north-dipping, brittle-ductile shear zone related to the nearby terrane-bounding Sawyer Brook fault. This deformation zone cuts volcaniclastic sedimentary and volcanic rocks of the Silurian Waweig Formation, and is intruded by mantle-derived East Branch Brook gabbroic dikes and a number of felsic dikes. Intermittent shear-zone reactivation during local magmatic activity induced heterogeneous deformation and alteration of the country rocks and dikes. The terminal phase of shearing is associated with narrow pegmatite-aplite dikes that grade laterally into granophyric granite, and into an auriferous quartz vein. Gold, aurostibite, and gold-antimony intergrowths, predominantly with vein quartz, are associated with a low ƒO2 sulfide mineral assemblage (pyrrhotite, arsenopyrite, and berthierite) that has a sulfur isotopic signature consistent with a magmatic source. Gold saturation and deposition occurred episodically between 300° and 360°C at low activity of sulfur, predominantly in response to pressure reduction during brittle failure combined with the effects of decreasing temperature and sulfidation reactions during fluid-wall-rock interaction. Geochronological studies demonstrate that the timing of the emplacement of the pegmatite-aplite dikes and associated auriferous veins overlap with that of the Early Devonian Magaguadavic granite. Moreover, the composition of the dikes is consistent with their derivation from this granite as late fractionates. The Main zone of the Clarence Stream deposit is therefore interpreted to be intrusion-related, with the Magaguadavic granite being the ultimate source of the gold-bearing fluids. La minéralisation de la zone principale du gisement aurifère de Clarence Stream dans le sud-ouest du Nouveau Brunswick occupe une série de veines de quartz parallèles dans une zone de cisaillement fragile-ductile de direction NE et à pendage abrupt vers le nord apparentée à la faille de Sawyer Brook avoisinante qui délimite deux terranes. Cette zone de déformation recoupe les roches volcaniclastiques et volcaniques de la Formation de Waweig d’âge Silurien et est recoupée par les dykes de gabbro d’East Branch Brook, d’origine mantellique, ainsi que par divers dykes felsiques. La réactivation intermittente de la zone de cisaillement durant l’activité magmatique locale a entraîné la déformation et l’altération hétérogènes des dykes et de l’encaissant. La phase finale du cisaillement est associée à de minces dykes d’aplite-pegmatite qui passent latéralement à des granites granophyriques, puis à des veines de quartz aurifères. L’or, l’aurostibite et les intercroissances d’or et d’antimoine principalement associées aux veines de quartz sont associés à un assemblage minéral de sulfures à faible ƒO2 (pyrrhotite, arsénopyrite et berthierite) présentant une signature isotopique du souffre compatible avec une source magmatique. La saturation en or et la précipitation a eu lieu épisodiquement entre 300° et 350°C dans des conditions de faible activité de souffre, principalement en réponse à la baisse de pression durant la rupture fragile ainsi qu’aux effets de la baisse de température et aux réactions de sulfuration durant l’interaction entre le fluide et l’encaissant. Les études géochronologiques indiquent que l’âge de la mise en place des dykes de pegmatite-aplite et des veines aurifères qui leur sont associées coïncide avec le granite de Magaguadavic, d’âge Dévonien Précoce. De plus, la composition des dykes est compatible avec une origine provenant de ce granite sous la forme de phases fractionnées tardives. Le gisement principale (Main zone) de Clarence Stream est ainsi considéré comme étant associé aux intrusions, le granite de Magaguadavic étant la source ultime des fluides aurifères."

Jan 1, 2008

By Diógenes Albert Gomes

Neste trabalho são apresentados os impactos físicos e mecânicos da reciclagem de insumos refratários compostos por óxidos de magnésio ligado ao carbono, visando à reutilização destes como matéria prima para a confecção de novos tijolos. Os resíduos refratários substituíram, na formulação proposta, 100% massa de MgO utilizado nestes tijolos. O estudo envolveu a confecção dos novos tijolos e a realização de ensaios de caracterização dos tijolos produzidos, através de ensaios físicos. Os resultados mostraram uma porosidade final elevada na condição sem cura, resultando em valores de densidade e resistência inferiores aos dos tijolos produzidos com matérias-primas virgens.

Aug 16, 2017

By C. Villachica

El presente texto refiere la aplicación del carbón activo como reactivo en las soluciones de los procesos de concentración por flotación minera. La justificación de su uso es porque la mayor selectividad del proceso incrementa significativamente las utilidades de la compañía minera. Asimismo, otros usos del carbón activo en estudio, se extienden a la absorción de iones perjudiciales a la flotación, mejoramiento de la flotación bulk, recuperación de espumante y colector, recuperación de finos, mejoramiento de la sedimentación de los concentrados y la recuperación de la plata y oro de los efluentes de la fundición y relaves.

Oct 14, 1980

By R. J. Lytle

INTRODUCTION Prior to excavation in soil and rock, it is useful to know the subsurface structure. This is important information both for safety and for equipment scheduling reasons. It is useful to know whether parts of the subsurface might be potentially troublesome or of different character than is generally thought present. By using geophysical probing, it is possible to infer the location and size of these unusual regions. The ground structure is commonly estimated from core samples taken from boreholes. These cores give a detailed knowledge of the structure in the borehole. However, knowledge of the structure exterior to the borehole can only be extrapolated from core data. By using seismic and electromagnetic cross-borehole geophysical probing, remote probing can be used to sense the region exterior to boreholes. A recent advance has significantly improved the state-of-the-art for defining the ground structure between boreholes. This new procedure utilizes large amounts of data and provides a detailed picture of the subsurface. The data processing algorithms used are similar to those in medical imaging of the human body using x-rays, a science called x-ray tomography. This imaging of the ground is called geotomography, which is a shortened acronym for geophysical tomography. Several examples of geotomography applied to imaging ground structure are presented. Our approach has been to probe the ground with electromagnetic and seismic waves. We map the region of interest with signals transmitted between multiple source and receiver pairs lowered in boreholes on opposite sides of the region (Figure 1). The received signals vary according to the transmission properties of the media

Jan 1, 1979

By W. S. Steinberg

In 1963, the full-scale engineering study for the development of an iron, steel, and vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steelworks that produced steel and vanadium-bearing slag from a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for prereduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to open slag bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of the higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

By B. D. Paphane

Since the commissioning of the Tati Hydrometallurgical Demonstration Plant (HDP), which produces Ni and Cu cathodes as well as Co salt from sulphide concentrate employing Activox® technology for leaching, no kinetic data has been generated from the plant under normal operating conditions, from start-up to steady state. Therefore, this study seeks to determine the rate of reactions in the leaching circuit with a view to obtaining kinetic data for the system under the current operating conditions. Within the five-compartment autoclave operating at temperatures of 105°C to 110°C and 1100 kPa pressure, the extraction of Ni, Cu, and Co ions into solution is achieved through the oxidation of the sulphide concentrate using approximately 50 kg H2SO4 per ton, 10 kg NaCl per ton, and 1.21 kg O2 per kilogram of S2-. The autoclave reactions showed complex kinetics, with the reactions proceeding via some intermediate(s) before the formation of products. The results suggest that the reactions were dependent on the size of the metal ion of interest and the concentrations of the metal ions in the Tati concentrate as well as in chloride leaching. The order of the leaching rate constants was Fe2+ > Cu2+ > Ni2+ > Co2+ in all the compartments studied. The rates of leaching were also found to decrease as the concentrate moves from compartment 1 to compartment 4. For compartments 1 to 3, leaching was observed to be preceded by dilution of the repulp liquor (copper raffinate). The leaching rate for compartment 5 was slightly lower than that of compartment 1 but higher than the rates of compartments 2, 3, and 4 for all the metals studied. Keywords kinetics, hydrometallurgical plant, Activox

Jun 1, 2013

By M. C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuel cell vehicles, a broad-scoped project was initiated to quantify the costs associated with operating fuel cell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This paper outlines the results of the investigations to date defining the costs/benefits associated with capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment, and infrastructure savings are possible with the application of fuel cells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft, and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuel cell mining equipment is currently higher than diesel versions, the high cost of fuel cells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case, the operational savings would probably be sufficient to balance the supplementary capitalization costs. Comprehensive reports have been issued.

May 1, 2005

By G. Righettini, G. Desrivières, P. Mousset-Jones, R. Lacroix, M. C. Bétournay, P. Laliberté, S. Hardcastle

"Under the requirement to define the economic advantages of using hydrogen fuel cell vehicles, a broad-scoped project was initiated to quantify the costs associated with operating fuel cell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another.This paper outlines the results of the investigations to date defining the costs/benefits associated with capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America.Significant ventilation power, equipment, and infrastructure savings are possible with the application of fuel cells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft, and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuel cell mining equipment is currently higher than diesel versions the high cost of fuel cells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case, the operational savings would probably be sufficient to balance the supplementary capitalization costs.Comprehensive reports have been issued."

Jan 1, 2005

By C. Musingwini

The Bushveld Complex is economically significant and strategically important to South Africa, thus it is imperative that optimal extraction of platinum group metal (PGM) resources on the Bushveld Complex is achieved. Optimal extraction broadly requires that the maximum amount of ore is extracted by excavating and hauling the minimum amount of waste in the shortest possible time, at the least cost, and in the safest and most environmentally acceptable manner. In open-pit mine planning this entails among other things, minimizing the waste stripping ratio, whereas in underground mine planning it includes minimizing the metres of waste development. In conventional mining, the main development that is in waste or partly in waste and defines the mining grid pattern includes levels and raises. It was prudent to consider optimizing level and raise spacing in conventional mining because the method is a prevalent mining method on the Bushveld Complex accounting for nearly 70% of platinum production.

Jan 1, 2010

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

By C. Machio

This paper reports the results of a study to determine the effect of process control agent (PCA) on the characteristics of Ti-Mg powders during milling. It has been shown that a 2% increase in PCA content leads to up to a 40% increase in yield of the milled powder but reduces the kinetics of the mechanical alloying process. The introduction of 4% PCA decreases the mean powder particle size by up to 30%, whereas 6% PCA increases the mean particle size by up to 230%. The characteristics of the milled powders will be discussed in relation to the role of PCA in the milling process. Keywords Titanium?magnesium, mechanical alloying, PCA.

Jan 1, 2011

By Juan Mayta

Dada la situación actual y escenario post COVID-19, es fundamental adoptar estrategias de Gestión Colaborativa e Integrada de Proyectos, este artículo es el resultado de la aplicación de Virtual Design Construction (VDC) y Building Information Modelling (BIM) en la etapa de Diseño de un proyecto de reemplazo de Equipos Críticos en la Parada de una Planta concentradora de Cobre (Cu) para Sociedad Minera El Brocal, operación minera ubicada en Cerro de Pasco, Perú.

Sep 29, 2023

By S Thomson, M Lovitt, T Purvis, C te Kloot, T Nguyen, Z Liu

Ernest Henry Mine (EHM), located in north-western Queensland, is an underground copper/gold sublevel caving operation currently producing over 6 Mt/a of ore. The mass mining method of sublevel caving (SLC) used at EHM involves systematically blasting a series of uphole rings in parallel ore drives and drawing the broken ore using a top-down approach. Each ore drive contains multiple precharged rings to prevent having to charge in close proximity to the brow of the previously fired ring; however, the current initiation system still involves ‘hooking up’ all detonator lead cords of the first precharged ring. The unstable nature of a rill and working close to a brow presents hazards to personnel completing the hook-up process. There is also a business risk of ore loss when damaged ground support completely prevents access to the next precharged ring. If the hook-up step could be eliminated, the risk to personnel and the business would be significantly reduced.EHM engaged Orica Mining Services in 2016 to trial their WebGenTM 100 – wireless electronic blasting system (WEBSTM) for the first time in an underground mining environment. Having successfully signal-tested the equipment, two test holes were initiated, followed by a single production ring and then multiple production rings. In total, 30 production rings were successfully fired underground at EHM in 2017. To do this, WEBSTM was successfully integrated into EHM’s current charging and firing process, resulting in no business delays or loss to production. None of the 30 rings required hooking up and all were initiated from the surface with no personnel underground. A high level of ownership from all personnel involved ensured the trial was a success, and provided scope for wireless detonators to be used successfully on a large scale – both at EHM and other sublevel caving operations. WEBSTM is now a proven example of technology that can be used to improve safety in the mining industry, through eliminating the need for personnel to work in hazardous areas.CITATION:te Kloot, C, Liu, Z, Purvis, T, Thomson, S, Lovitt, M and Nguyen, T, 2017. Improving safety through technology – Orica wireless electronic blasting system trials at Ernest Henry Mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 39–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Michael Quadagno

Hudson River Pier 86, home of the historic USS Intrepid Aircraft Carrier and the Intrepid Sea-Air-Space Museum, is currently undergoing a $30M reconstruction. This project involves the demolition of the old timber pile supported pier and construction of a new 150 ft wide by 782 ft long concrete pier, built over the footprint of the old piles. The new pier consists of steel pipe piles, precast concrete pile caps, and a composite deck, made up of precast, prestressed concrete planks and cast-in-place concrete topping. This paper focuses on both the structural design and construction of the new pier, with emphasis on the pile foundation. Pier 86 is unique in that it is required to resist the extremely high lateral loads imposed on it by the permanently moored 898 ft long aircraft carrier during severe storms. A total of 360 steel pipe piles support the new pier. These piles, which are 24 in. in diameter and range in length from 58 ft to 175 ft, were driven down to bedrock. The piles, each having 200 ton allowable capacities, work together to resist the significantly large lateral loads exerted on the pier by the ship. The installation of the piles was unique in that all the piles, including the ?super-longs?, were fabricated to-length offsite, delivered to the site via truck and barge, and installed in one piece, eliminating the need for field splicing. The Pier 86 reconstruction will be completed within an extremely aggressive 18 month schedule, from January 2007 through June 2008. The refurbished aircraft carrier Intrepid will return home in September 2008, and the grand re-opening of the pier will be on Veteran?s Day 2008. This paper provides a case history for owners, government agencies, engineers, and construction professionals that will be faced with the challenges of designing and building new piers.

Jan 1, 2008

By Miguel Ángel Zúñiga Castillo

El presente texto señala la importancia del transporte minero como actividad en el sistema de costeo. En ese sentido, este se divide en transporte al interior de la mina y al exterior de ella. El primero implica que el mineral sea transportado in situ hasta la tolva de la planta de beneficio, donde no hay una etapa de transformación o concentración, mientras que el segundo traslada los concentrados hasta su destino final como son las fundiciones y refinerías en el mercado europeo, asiático y americano. Por ello, se busca seleccionar la mejor etapa de transporte que responda a las condiciones de las máquinas y equipos que trasladen el mineral desde el interior a la superficie de la mina. Así también se realiza un análisis macroeconómico de la importancia del flete en la actividad minera, originando un perfil de ahorro en la generación de divisas para el fortalecimiento del rol minero en el país.

Nov 24, 1986

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009

By Randall M. Wheeler

It is important to be able to quantify the effects of blast delay designs on vibration characteristics. White was the first company to develop commercially available software, called Alpha-Blast, for this purpose. The program can indicate relative amplitude and frequency results to be expected from the use of particular delay intervals. If enhanced vibration effects from delays are a problem, a technique to evaluate this situation will be invaluable.

Jan 1, 1994

By Wayne Burmeister, Danie Benade, Louis Meyer, Hugo Joubert

What is not measured cannot be managed. This is true of most things, including a furnace lining. This paper describes a Lining Management System used for this purpose. It provides the operations staff with a management tool to predict long term lining life and acts as a process optimisation tool. It alarms and records upset furnace conditions. Outputs from the system are described as presented through a specially developed software package and interface. It includes vertical and horizontal furnace sections showing estimated isotherms through the lining as well as the furnace bath. It also shows calculated heat flux values, estimated lining wear and the freeze layer profile. A novel three-dimensional display is described which provides the operator with a big picture view of the furnace crucible profile under real time operating conditions. The powerful trending facility for analysing both measured and calculated values is discussed. The required instrumentation hardware as well as the installation thereof is described, with special reference to an electrically insulating thermocouple socket design. Finally feedback is provided on the first year?s performance of the system installed on an open ferrochrome furnace at Assmang Chrome, Machadodorp, South Africa.

Jan 1, 2007

By Vladimir N. Rudashevsky, Louis J. Cabri, Nikolay S. Rudashevsky, Thomas Oberthür

"EPD (Electric Pulse disaggregation) and HS (hydroseparation) are exceptional technologies for research, concentration, evaluation, and mineral extraction of specific minerals such as precious metals (Au, Ag, PGM), kimberlites (extraction and concentration of indicator minerals), zircons and baddeleyite (recovery of objects for geochronology), and even gemstones (method of evaluation and production of the 100% gemstone concentrate of ideal crystals) etc. EPD is used for recovery of pristine undamaged crystals of diamond, emerald, ruby, sapphire etc, including large crystals. It was tested on various hard ores and was especially successful for recovery of “soft” minerals from “hard” matrix. EPD products are very convenient for HS processing, resulting in representative concentrates of all heavy minerals including the finest particles (5-10 µm). The combined EPD and HS method enables high sensitivity (20 ppb) for evaluation of precious metal ores providing objective information about original grain size, associations, and recovery using a very small amount of sample (1-3 kg). Latest developments of EPD and HS techniques at CNT Mineral Consulting Inc. include the HS-21 hydroseparator (50 kg/hr) and the Spark-21 EPD (5 t/hr), which enables use of both techniques for prospecting and mineral processing of industrial size samples of certain ores.INTRODUCTIONThe main task for mineral processors is to find a reliable technology for testing of mining feasibility and the efficiency of mineral extraction procedures. Among various mineral processing approaches of extraction and concentration there are two alternative cost-effective methods that can be described as the most environmentally benign and complementary: electric-pulse disaggregation and hydroseparation. These techniques were tested on many different ore types and process products with great success providing a precise and comprehensive mineralogical determination of different accessory precious metal and other useful minerals constituent in rocks, ores, and tailings.This article describes several examples of EPD and HS use: native gold from the Kostomuksha deposit (Karelia, Russia), a Ag-Au deposit in South America, zircons from ancient ultramafic igneous rocks of SW Greenland, bauxites of West Australia, PGM from the Driekop dunite pipe and gemstones (ruby, sapphire, emerald and demantoid) from different deposits."

Jan 1, 2008