Search Documents

By M. N. Bassim, W. W. Tennese

"Concepts of linear elastic fracture mechanics were applied to study two cases of failure, namely an equalizing beam from a tandem rear axle of a highway tractor unit and the main beam of a flat bed trailer. In the first case, the presence of a crack, initiated by stress corrosion cracking followed by significant fatigue crack propagation produced a state of stress which was sufficient to produce brittle failure. Calculation of the fatigue life agreed with the number of cycles that the structure experienced before final fracture. In the second case, it was demonstrated that a combination of low temperature and high loading rate was sufficient to cause brittle fracture.IntroductionFailure analysis of engineering components has generally been carried out without the benefit of fracture mechanics. It is generally understood that real structures inevitably contain internal or surface flaws which under an applied load, may propagate to fracture. Fracture mechanics relates the applied stresses to the crack size in specified geometries. Since its introduction approximately thirty years ago, fracture mechanics has evolved as a design philosophy which can be used to develop fracture-safe designs. It can be also applied in analysis of failures, to ascertain if sound design and fabrication methods have been used."

Jan 1, 1985

By C. Doucet

Since 2001, CANMET Mining and Mineral Sciences Laboratories (MMSL) have worked with Falconbridge Ltd. (now Xstrata Nickel) to evaluate trends in the strength development and water retention properties of a novel backfill material for underground mining, called gelfill. Between 2004 and 2006, extensive laboratory tests were undertaken under the leadership of the Deep Mining Research Consortium (DMRC). This paper compares results obtained from samples circulated through a mini-flow loop and a simple mixer. Although many parameters were studied over the last five (5) years, this paper focuses on the investigation of the effect of the mixing method, sequence and time, and the curing environment on strength development and water retention of gelfill. It was found that binder should be added as a powder to the mix in the mini-flow loop, and that mixing slurry in the mini-flow loop as opposed to the mixer generally yielded higher strengths. The practical implications of these observations are the subject of an on-going underground trial that will compare laboratory and in situ properties of regular slurry fill with gelfill.

May 1, 2007

Talvivaara deposits, Kuusilampi and Kolmisoppi, comprise one of the largest sulfide nickel resources in the world with 642 Mt in Measured and Indicated Resource categories. TalvivaaraÆs preferred extraction technology is bioheapleaching, which is already widely used for other metals, notably copper and gold. The company has demonstrated the viability of bioheapleaching technology for the extraction of nickel using the Talvivaara ore. The leaching process is heat generating and therefore suitable for the subarctic climatic conditions. The planned annual metal production is 33 000 t of nickel, 60 000 t of zinc, 10 000 t of copper and 1200 t of cobalt. Talvivaara deposits are well-suited for open pit mining due to a thin overburden, favourable resource geometry and a low waste to ore ratio. The ore is relatively low-grade, but well suited to bioheapleaching due to its high sulfide content. Bioheapleaching is a process whereby metals are leached from ore as a result of bacterial action. The bacteria used in the Talvivaara bioheapleaching process are endemic to the area and therefore well adjusted to the prevailing environmental conditions. The solution is collected at the bottom of the heaps and either re-circulated through the heap or fed to metal recovery. In metal recovery, nickel, copper, zinc and cobalt are precipitated from the pregnant leach solution and filtered to produce saleable metal products. After the metals are removed, the solution is further purified and returned to irrigate the heaps. Mining, bioheapleaching and metal recovery techniques for the Talvivaara mine have been tested in a 17 000 t on-site demonstration trial during 2005 and 2006. Subsequent construction of the mine started in 2007 and commercial production in the fourth quarter of 2008.

Jan 1, 2009

By R. J. Gunderman

A conventional trailing cable connection box on a continuous mining machine was modified by the addition of two innovative devices. These are a pressure vent to preclude buildup of high pressure due to an explosion in-side the enclosure, and a grommet-type cable entry to simplify and speedup cable entering procedures. The innovative devices were evaluated for eight and one-half months in a working section of an underground coal mine. Laboratory tests before and after the in-mine exposure show no measurable change in the devices. Following the favorable in-mine evaluation, technical performance criteria were defined to serve as the basis of approval for the use of the innovative devices. Additional tests to measure comparable gripping of the cable by asbestos rope, substitution rope materials and by the urethane grommet-type entry were included in this effort. Also, literature for the last 80 years was searched. Comments are provided as to how the innovative devices comply with 30 CFR Part 18.

Jan 1, 1982

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By Z. Lin, M. Isac, R. I. L. Guthrie

The kinetic and thermodynamic efficiencies of chromium recovery from the slag in an AOD process during the slag de-oxidation period with ferrosilicon is a complex process affected by slag basicity, temperature, the dissolution kinetics of the reducing agents, and intermixing of the slag/metal/alloy addition phases within the vessel. The present work focused on a study and simulation of the fluid dynamics and mixing behaviour of ferrosilicon additions in the AOD process for the production of stainless steel. In order to visualize the mixing behaviour, a two dimensional slice model of an AOD vessel was first built and filled with ZnCl2solution and then covered with silicone oil in order to represent the bulk liquid steel and slag phases, respectively. The injection of argon/oxygen process gases was simulated using air or helium. Particle trajectories and intermixing of the phases was monitored with a high-speed camera. To simulate the 75FeSi additions, glass spheres were used. A three-dimensional version of the AOD model was then constructed in order to confirm the adequacy of the slice model. Similar particle mixing behaviour was observed. Both models demonstrated that the ascending gas/liquid plume created two asymmetric mixing zones: a smaller rapidly re-circulating mixing zone adjacent to the side-wall locating the tuyere(s), and a larger mixing zone in the main part of the vessel. The process efficiency during the reduction period is governed by the thermal behaviour of ferroalloy as well as the mixing efficiency in the main large mixing zone. To enhance the recovery efficiency for chromium, small Fe-Si particles are suggested, given their wide distribution within the slag phase, and their large interfacial areas and rapid melting times for Cr2O3reduction from the slag. Keywords; modelling, ferrosilicon, chromium oxidation, AOD steelmaking.

Jan 1, 2004

By Douglas Milne

Most empirical and numerical approaches to design in rock mechanics incorporate rock mass classification. Numerical design methods generally use classification values to calculate input parameters for stress-based failure criteria. Empirical methods use classification to allow comparisons between similar rock mass conditions, generally based on a graphical design technique that differentiates stable and failed opening geometries. Classification systems are the best tool available for assessing rock mass properties; however, there are problems with classification systems that should be high-lighted. Rock mass performance can only be realistically estimated by coupling a unique description of the rock mass with known loading conditions. Current classification systems cannot provide a unique classification value. The weightings applied to quantify rock mass properties for classification can result in significantly different rock masses having the same classification values. These weightings have been proven effective for tunnel design and support, but classification systems are now used for many more applications. Rock classification systems evolved from a quick and easy field tool for estimating tunnel stability and support requirements. The need for a rapid field tool means that rock mass classification is relatively insensitive to improved methods of measuring rock mass properties. Problems with classification systems and their application are highlighted in this paper. These problems must be recognized and documented before improvements can be made. An understanding of the evolution of classification systems and their application for both numerical and empirical design approaches is invaluable in highlighting current shortcomings.

Jan 5, 2007

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pres-sure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports.5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolande No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a positive identification of the bed at Yolande No. 6 will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 180. As far as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By A. Yu. Lein, V. V. Maslennikov, S. P. Maslennikova, I. Y. u. Melekestseva, Yu. A. Bogdanov

Tellurium is a high-tech and also toxic element. This element shows sufficient contents in Fe-Mn crusts and nodules in the modern ocean to be involved in future industrial processes [Hein et al., 2003]. Tellurium minerals and contents are not well recorded in modern and ancient black smoker systems. Tellurides are rarely found in sulfides from the modern oceans [Iizasa et al. 1992; Maslennikov et al., 2010]. The previous common opinion that tellurium is scarce in active seafloor hydrothermal systems can be revised due to the recent discovery of abundant tellurides in chimneys from Brothers Volcano vent site [Berkenbosch et al., 2012]. We found abundant tellurobismuthite, hessite, and native tellurium in chimneys from Su Su Knoll vents sites (West Pacific). So, tellurides can be found in some chimneys but absent in others. The causes of this are poorly understood. These conflicting data create numerous questions and require an explanation. The problem can be resolved by research at different scales including analysis of relevant genetic features of host sequences, systematic textural and paragenetic studies of different types of chimneys, and their rare mineral assemblages. Paragenetic models, compositional analyses and ranges of tellurium-bearing minerals and the physicochemical interpretation of chimney diversity in different types of VMS deposits are the main subjects of our research. The data on tellurides in chimneys from ancient VMS deposits should also be useful to resolve this problem.

Sep 1, 2014

By G. H. Lewis, C. L. Krcil, N. S. Harding, D. E. Havekotte

Introduction Limestone injection work was completed in a 440-kW (1.5-million Btu per hour) pilot-scale combustor in preparation for a 50,000-kg/h (110,000-lb per hour) industrial steam boiler limestone injection test program. The main objectives were to: (1) identify the important variables that affect sulfur capture, (2) determine the maximum SO2 removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. A more detailed report is given by Lewis et al. (1985). The test program was divided into two phases. The objectives of Phase I were to determine the important variables that affect SO2 reduction and to investigate the effect of limestone addition on combustor operation and heat transfer surfaces. The objective of Phase II was to determine, using only the important variables identified during Phase I, the conditions that resulted in the greatest sulfur dioxide reduction. Phase I Test program Using one limestone, five variables were identified as having an effect on SO2 reduction. These are noted with their respective ranges: heat release rate [103 to 166 kW/m3 (10,000 to 16,000 Btu per hour-cu ft)], Ca/S molar ratio (0 to 3), flue gas oxygen concentration (3% to 5%), additive particle size [90% -150 µm (-100 mesh) and 90% -45 µm (-325 mesh)], and burner stoichiometry (SR = 0.75 and >1.15). A 2.3% sulfur northern West Virginia coal, pulverized to a nominal grind of 70% -75 µm (-200 mesh), was burned for the tests. The limestone used was obtained from a Maysville, KY, quarry and contained 51.75% (wt) CaO. An 11-run statistically designed program (plus three duplicates) was used to screen the five variables. The effect of limestone injection on the combustor heat transfer surfaces was determined by comparing the heat transfer rates through a slag panel and fouling probes during periods with and without limestone injection. Combustor operation was determined by noting any operating problems that occurred during the tests. Test procedure After furnace wall temperatures had stabilized at operating conditions, heat transfer surfaces (slag panel and fouling probes) and the convection section were blown clean, and a four-hour test was begun. The

Jan 12, 1986

By David P. Reddick

"Suncor Inc. Oilsands Group mining operation in Northern Alberta, Canada, has been blasting to loosen the oilsands to increase production and decrease maintenance of the bucketwheel excavators for over twenty years. In 1991 an area of the mine was encountered which had a working face of 130 feet rather than the usual 20 to 57. In order to maintain production objectives, the planning and blasting departments of the mine took on the task of blasting as much of the working face as possible. McGinnis Rathole Drilling Company provided the drilling for the project and Mining Services International (MSI) delivered the bulk explosives to the boreholes. It is believed the resultingblasts exceeded several known records in production blasting."

Jan 1, 1992

Present roof bolting practices in the collieries of Australian Iron and Steel Pty. Ltd. are outlined. Roof support has been improved since introducing roof bolts and it is hoped to increase the reliability of the bolts still further.Expansion-shell, and split and wedge roof bolts five to eight feet long are placed by "Atlas Falcon" and "Fletcher" roof bolters. Both anchorage and tightening have presented some problems.Good panel supervision is required if systematic roof bolting is to be properly co-ordinated with coal production without unnecessary delay to either. Successful roof bolting can only be the product of conscientious men and supervisors who are all convinced of its value. A rigid operational code should be established early and maintained.INTRODUCTIONRoof bolting is a method of support which is permanent and reduces or eliminates the need for other support; The method was pioneered in America and was first experimentally investigated in Australian collieries at Elrington in 1949 (McKensey, 1953). Pneumatic installation methods were employed. Subsequently, a method of using standard hand-held electric coal drills was developed at John Darling Colliery (Horseman, 1954). Pneumatic roof bolting equipment was first operated in the collieries of Australian Ironand Steel Pty. Ltd (A.I. &. S.) in 1951. Since then various hydraulically operated mobile machines have been installed in Australian collieries and these, together with improved pneumatic equipment, form the two present basic methods of placing ,roof bolts. Roof bolt anchorage is achieved by either split and wedge or expansion-shell bolts.The two broad types of roof bolting are 1. consolidation of strata, and 2. suspension support.

Jan 1, 1961

By P. K. Hofmeyr

Base Metal (Cu, Ni, Mo, Zn, Co etc.) analysis traditionally has been very slow in conventional analytical laboratories which can lead to additional costs being incurred in waiting time of drill rigs or mining excessively off-reef. Recent developments in the automation of analytical laboratories now allow for very rapid turn-around times for base metal analytical data which can help reduce such costs as well as reduce the unit costs of the analyses themselves. 2.0 CONVENTIONAL ANALYTICAL LABORATORY PRACTICE Conventional analytical laboratories are necessarily are very manual. Sample preparation is slow and laborious, samples are moved from stage to stage manually and, typically, all samples are processed in batches so a sample which is the first to be, say, milled has to wait for the complete milling of the batch before it advances to the next stage eg. mixed with wax prior to pelletising for XRF analysis. Inevitably this results in long sample data turn-around times for laboratories handling large numbers of samples. Manual sample preparation can only be accelerated by increasing staff which increases costs and can lead to additional errors being introduced. Cleaning of sample preparation equipment, eg. crushers and mills, between samples is essential to avoid cross-contamination between samples and this is slow and labour-intensive. In manual sample preparation the correct sample numbers staying with the samples is totally dependent on the efficiency of laboratory operators. It is extremely difficult to detect when errors have occurred due to the switching of sample numbers during the sample preparation stages. Running duplicates and QC samples at best is only partially successful in detecting when sample number switching errors have occurred. Errors of this nature and cross-contamination problems due to incomplete cleaning of sample preparation equipment tend to occur when laboratories are working at pressure due to high sample numbers and when supervisors are not present during 24/7 laboratory operations which is often required on plant process control laboratories. These problems are common to all conventional analytical laboratories and their magnitude is dependent on the level of control and efficiency of QC systems practised by individual laboratories. The disadvantages of conventional manual analytical laboratories can be summarized as follows:- 1. Labour-intensive which is costly especially when multiple shifts have to be used during 24/7 operations.

Jan 1, 2005

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

Jan 1, 1997

By J. G. Donaldson

Optimum conditions are given for chloridizing pyrite, marcasite, chalcopyrite, arsenopyrite, stibnite, and covellite with chlorine gas. The formation of metal chlorides is affected by the time and temperature of chloridizing, and by particle size of the sample. Chloridizing data also are given for chemically precipitated antimony (III) sulfide and copper (II) sulfide.

Jan 1, 1962

By Loren R. Anderson

Traditionally, an evaluation of the safety of slopes has been based on computing a safety factor against failure. In computing the safety factor, the geometry of the slope, the soil parameters and the pore pressures are treated as deterministic quantities even though they are known to be random variables. A pseudo-three-dimensional probabilistic slope stability model has been developed that treats shear strength as a random variable. The model uses the probability of a slope failure as an assessment of slope reliability. The model can accommodate zoned embankments of soil in which the strength is described by the Mohr-Coulomb strength envelope. Autocorrelation functions are used to describe the spatial correlation of the strength parameters, c and tan ø. Model error can also be included in the analysis. The model has been applied to an existing tailings dam and to several hypothetical examples. These examples are presented to illustrate the influence of the choice of the soil strength variability parameters on the probability of failure. The results show that the critical failure surface based on the minimum safety factor is not necessarily the failure surface that will yield the maximum probability of failure. The analysis of the tailings dam shows that variance reduction can be large and that the model error is the dominant source of uncertainty for the embankment analyzed.

Jan 1, 1982

By Khamis Y. Haramy

Quality assurance and quality control of drilled shafts has become a concern due to difficulties in accurately locating construction anomalies and determining load bearing capacity of defected drilled shafts. Various non-destructive evaluation techniques have been developed to estimate the integrity of the concrete in drilled shafts. While these techniques have been widely accepted, variables and unknowns can affect the measurement results. Results are typically difficult to interpret, leading to unnecessary construction delays and possible litigation over shaft integrity. In addition, influences of surrounding ground materials, stress states under different load conditions, and crack and residual stress development during concrete curing further complicate determination of shaft performance. This paper focuses on the evaluation of load bearing capacity of defected drilled shafts under various conditions by numerical analysis and modeling.

Jan 1, 2007

By W. F. Van Impe

The design of piles and of pile groups has remarkably progressed over the past two decades. The in­creasing complexity of the building concept implements a more rational approach of the deep foundation capacity and its interaction with the structure. Moreover, the understanding of the soil characteristics relevant to deep foundation behaviour, is continuously in progress because soil parameters are always more accurately determined; which also contributed a lot to the recent developments in pile capacity design. At last, due to the increasing sensitivity of buildings to deformations, continuous attention must be also paid to pile group settlements. The aim of this report is to discuss some of the mentioned more important pile design developments.

Jan 1, 1994