Search Documents

By M. E. Alam

In the present study, 1.1 volume percent of nano size copper was incorporated into pure tin using hybrid microwave sintering assisted powder metallurgy route. Microwave sintered samples were extruded both at room temperature and at 230 °C. Microstructural characterization studies were conducted on the extruded samples to investigate the distribution characteristics of secondary phase and grain morphology. Room temperature tensile test results revealed that hot extruded Sn-Cu samples exhibited higher strengths (~ 41%, in case of 0.2% yield strength and ~ 38%, in case of ultimate tensile strength) and ductility (~ 15%) when compared to room temperature extruded samples. On the contrary, the tensile properties of pure tin remained independent of extrusion temperature. An attempt is made in this study to correlate the effect of extrusion temperature on the microstructural evolution and tensile properties of Sn-Cu solder.

Jan 1, 2009

By E. H. Myrhaug, K. Aasly, T. Malvik

Six different types of quartz and quartzites used as raw materials by ferroalloy plants have been investigated with respect to their thermo mechanical properties. In order to investigate the effect of the thermal shock caused by the rapid heating of quartz when it enters the furnace, the following techniques have been used for both in situ investigations and investigations of pre-heated quartz: -Heating stage microscopy for in situ observation of heating effects. -Shock heating of quartz in an induction furnace An optical microscope-mounted heating stage was used for in situ observations of the microscopic effects of heating up to 1300 ºC. The effects of heating were observed at different temperature intervals in different samples. The main temperature intervals were below 573 ºC and above 1000 ºC. The cause of the observed effects is interpreted as fluid inclusion decrepitation for T<573 °C and structural implications (micro cracks, grain boundaries and remaining fluid inclusions) at T>1200 °C. Shock heating of the samples was carried out in an induction furnace to 1300 ºC for ten minutes. The effects of the heating were studied with different techniques such as direct observation during and directly after heating, optical microscopy and XRD. Combined transmitted and fluorescence light microscopy shows that the heated quartz show an opening of the grain boundaries and evenly distributed micro cracks that were not present in the unheated reference samples. In some of the heated samples, weak generation of cristobalite was detected by XRD.

Jan 1, 2007

By E. H. Burroughs

Persons interested in th_e study of petroleum and allied substances have long felt the need of a bibliographic index to the literature. This bibliography, which is intended to be the first elf a yearly series, has been compiled by the petroleum division of the Bureau of Mines with a view to satisfying this need. The references include only the more noteworthy writings that appeared during the year 191.5 in both ·the United States and foreign countries. Only patents plainly applicable to the industries in point have been included, although, of course, a close scrutiny of the great volume of patent literature might reveal many other patents of possible value. The references are arranged according to the subject classification on pages 3 to 11. This classification, which is to be followed in the succeeding bibliographies of this series, is offered as a guide for further study and classification of the pertinent literature.

Jan 1, 1918

By L R. Marshall, M J. Rubenach, T G. Blenkinsop, J S. Cleverley

The source and transport regions of fluidised (transported) breccias outcrop in the Cloncurry Fe-oxide-Cu-Au district, providing insights into the origins of other fluidised magmatic-hydrothermal breccias such as kimberlites. Discordant dikes and pipes with rounded clasts of metasedimentary calc-silicate rocks and minor felsic and mafic intrusions extend several kilometres upwards and outwards from the contact aureole of the 1530 Ma Williams Batholith into overlying schists and amphibolites. The brecciation initiated at depths &gt;10 km and may have resulted in surface breaching. We used analytical equations for particle transport to estimate clast velocities (eÆ 20 ms-1), approaching volcanic ejecta rates (up to 80 ms-1). The wide range of CO2 fluid inclusion densities (up to 150 MPa), the localisation of the base of the breccias in contact aureoles, and the scale and discordancy of the bodies suggests the breccia transport process was triggered by an abrupt release of overpressured fluid. At these depths, such extreme behaviour may have been achieved by release of dissolved fluids from crystallising magma, in combination with a strongly fractured and fluid-laden source, sitting under a strong, low permeability barrier, and such parameters may be analogous to the asthenosphere/lithosphere boundary in the case of kimberlite initiation. The relationship of these breccias to the Ernest Henry iron-oxide-Cu-Au deposit suggests they may have been either fertile or æfailedÆ orebody feeders.

Jan 1, 2005

By Stephen R. Iverson

Manganese deposits exist in the Wonder Mountain RARE II area (fig. 1). The manganese mineral is primarily bementite, a silicate. It occurs with Jasper and manganese oxides in tabular or irregular lenses along the contact between red limestone and basalt. There are about 11,000 tons (10,000 t) of indicated sub-economic resources in the northeast part of the study area. Of this, 10,700 tons containing 27.1 percent manganese is at the Apex Prospect and 300 tons averaging 24.8 percent is at the Brown Mule Mine (fig. 1). Another 1,000 tons (900 t) containing 27.0 percent manganese is at the Steel Creek deposit 0.5 mi (0.8 km) west of the area (Wiebelt, 1942, p. 1, 2). Each of these deposits is subeconomic due to small tonnage and high estimated recovery costs. They are in a regional belt of manganese occurrences trending northwesterly through the area. Pardee (1921) reports that manganese ore was shipped from the Triple Trip (Brown Mule) Mine in 1916.

Jan 1, 1982

By Samuel Frimpong

The interaction of oil sands with a ground articulating pipeline (GAP) system has been simulated with the dynamic model established in this work by combining the multi-body and soil dynamics with the Automatic Dynamic Analysis Mechanical Systems (ADAMS) software. Mathematical models governing the interaction of the GAP system with the oil sand terrain have been modeled based on the theory of multi-body and soil dynamics. These models consist of GAP track-oil sand contact model for generating the contact force between oil sands and track and load-deformation oil sand model for capturing the dynamic behavior of oil sands. A virtual prototype has been created and simulated in the ADAMS environment. The simulation result of the effect of load on oil sand deformation indicates that maximum deformation value increases non-linearly with load varying from 0 to 60t. This study provides a solid foundation for further research and the GAP technology development.

May 1, 2004

By GA Harrison

The introduction of Extra Low Profile (XLP) mechanised equipment within Anglo Platinum is aligned with the overall New Mining Technologies strategy to focus on continuing modernization of our mining operations to achieve injury free sustainable production and cost effective mining technologies. The method allows for the introduction of a suite of XLP and Low Profile (LP) equipment in a narrow reef (1,2m) mining environment. For the first time it is now possible to achieve total trackless mechanisation at these stoping widths and XLP Breast mining has the potential to add more value when benchmarked with conventional mining and other mechanised methods. Various types of XLP equipment were tested at different sites within Anglo Platinum and this paper describes the XLP equipment evolution to-date. It concludes with recommendations on our future strategy regarding implementation and roll out of the XLP technology within Anglo Platinum.

Jan 1, 2008

The proper selection of a coal for a particular use depends on knowledge of fundamental data concerning the coals that offer, particularly their type and rank. Type of coal depends on the nature of the original plants and the environment in which they accumulated.Rank reflects the subsequent metamorphism of the coal, and is of two kinds-physical rank and chemical rank.INTRODUCTIONIn the different coalfields of the Commonwealth of Australia there occur many different kinds of coal which provide the coal-research worker with a wide range of material, but to the fuel technologist they represent complex problems in utilization.In the past it has been common practice to instal coal-using equipment of a design based on plant used in large industrial centres of other countries and then search for supplies of suitable coal. This has led to the transportation of coal mainly from New South Wales to other States, which have inadequate supplies of coal suitable for use in the equipment they have installed. However, modern economy and industrial practice demand local resources of coal for the development of industry, transport and domestic services, and a change in the old order is rapidly taking place. Technologists and engineers are now faced with the problem of designing and installing equipment to use whatever kind of coal is available in local coalfields.Much has been accomplished in this direction and important investigations are at present being carried out, but there still remains a wide field of problems for research.In planning and carrying out investigations into coal utilization it is essential that fundamental data and knowledge should be available and that its significance should be appreciated.

Jan 1, 1955

By William B. Hughes

The rubber-sleeve core barrel was developed to improve core recovery from unconsolidated sands, where it is most difficult to obtain cores with conventional barrels. The use of a rubber-sleeve core retainer, together with other departures from clsual design, has required a considerable amount of testing to prove its op-erability. Tests run in shallow experimental holes and in drilling wells in the U. S. and Vemzuela have, to a large extent, proved the operation of the barrel. Internal mechanism troubles, such as sandbinding of the sleeve, have been largely overcome. Cores have been recovered from completely unconsolidated sands where conventional coring has almost been abandoned because of poor recovery. In addition to retaining the core until brought to the surface, the barrel gives a "packaged-ar-cut" core, which is coilverzient for handling and transportatiorz. In the initial work, drag blade cutters, roller cutters, and tungsten carbide insert cutters were usrd for cutting unconsolidated sands. Further bit head development is presently being conducted using diamond heads in unconsolidated sands where shaler, hard sands, and limestones are encountered in adjacent formations. Thir work should render the barrel capable of cratting and recovering most types of formations, possibly including broken and frac- tured fornlations. This development is being carried on in cooperation with a diamond bit manufacturer. INTRODUCTIO N For many years the oil industry has needed greater recovery of cores from unconsolidated formations. Conventional equipment has been used to core unconsolidated sands with little success. Specifically, a core barrel was needed which would recover unconsolidated sands in a condition that would give useful reservoir information. DEVELOPMENT OF &apos;THE RUBBER-SLEEVE CORE BARREL Basic Requirements of Unconsolidated Sand Corino The basic need was defined as a core barrel that would obtain a continuous unconsolidated core with sand grains in place as deposited in the formation. A preliminary survey of coring equipment and search of the literature pointed out the weaknesses of conventional core barrels. Laboratory tests using unconsolidated sand in a metal tube simulated actual sand movement into the core barrel during conventional coring. In conventional barrels the core sometimes crumbles and bridges, or fails under compressive column action, becomes oversize, and wedges against the walls of the inner barrel. The core barrel requirements established by the surveys and preliminary tests are as follows. 1. The core should be held to- gether as it is cut so it cannot crumble and bridge against the walls of the coring tool, care being taken not to permit damage from fluid circulation. 2. The core should be continuously supported as it is cut so it will not have to support itself in compression. 3. The core should be packaged in the barrel to retain an undisturbed condition during the trip out of the well. The packaging should be such that the core can be removed from the barrel and shipped to the core analysis laboratory without physical disturbance or alteration of fluid content by exposure to the atmosphere. Operation of the Rubber-Sleeve Core Barrel The rubber-sleeve core barrel (Fig. 1) meets the basic requirements for the recovery of unconsolidated sands.

By Mark A. Williams

"This paper was originally intended to be a presentation of a case study of two surface bituminouscoal mines in the southern Appalachian coal fields located within five miles of each other. These mines were nearly identical in every aspect from geologic setting to equipment application. Althoughrepresentatives from each mine desired to participate in the preparation of this paper through support in providing background information and in review and editing, it was later concluded that, due to the environmental sensitivity associated with each mine, it may not have been a good decision to present this case study in a public forum."

Jan 1, 1994

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977

By Ludwig Schmidt

"IntroductionThe evaporation losses of gasoline in the refinery, can be reduced by proper methods of refinery construction and operation. When gasoline evaporates slowly, as when stored in tanks that are not vapor tight, the most volatile part evaporates first, so that the remaining liquid in not only less in volume, but is also lower in quality. In some,evaporation changes the characteristics of the product so much that it must be reblended to meet trade specifications.Refiners are, therefore, greatly interested in the various appliances and methods used to reduce these losses. In the past this interest has been directed largely to storage tanks, probably because evaporation from tanks is more readily observed than losses during other refinery operations. As tests by the Bureau of Mines on evaporation of gasoline from small storage tanks had indicated that the losses during the various stages of refining might be equal to or greater than those of standing storage, a survey was during the spring and early summer months of 1924 in a large number of refineries in the Mid-Continent field. In order to enable the refiner to select the results of those tests that conform most nearly to the conditions that he has to meet, tests were conducted at various stages of refining, as follows: (1) Randown tanks, (2) (agitators), (3) filling tank cars, (4) storage of refined products, and (3) miscellaneous handling. The results are presented in this paper."

Nov 1, 1925

By Jacques F. Abrahamse, Kevin A. Bahe, T. Arthur Palm, Gregory E. McCluskey, Stephen L. Bessinger

Introduction Basis For System San Juan Coal Company (SJCC) is a subsidiary of BHP Billiton. Until recently, BHP Billiton operated three surface mines in northwestern New Mexico: Navajo, San Juan, and La Plata. The San Juan and La Plata Mines supplied the San Juan Generating Station operated by Public Service of New Mexico. Stripping ratios at those operations were increasing, and by 2000 a feasibility study was underway to develop SJCC’s vast underground reserves as a replacement. Early in the evaluation and planning phase for the San Juan Underground Mine, it was determined that the target seams (Fruitland #8 and #9) had a high propensity for spontaneous combustion. Spontaneous combustion was identified as a risk, both to personnel and equipment, and to the ability of SJCC to reliably fulfill its obligation to the power plant. In the last 20 years, several western US coal mines suffered underground spontaneous combustion events and/or mine fires. Included in this group were Colorado Westmoreland’s Orchard Valley Mine (1987), RAG’s Willow Creek Mine (1998 and 2000), Oxbow’s Sanborn Creek Mine (1999), the West Elk Mine of Arch Coal (2000), Arch’s Skyline Mine (2002), Western Fuels’ Deserado Mine (1996), and the West Ridge Mine of Andalex Resources (2003). The cause for the majority of these fires was spontaneous combustion. Fighting the fires required injection of an inert gas or foam. Nitrogen and carbon dioxide were the predominant choices of inert gas. In all cases, the gasses had to be trucked in from considerable distances. Before the inert gas could be used, injection holes had to be drilled into or near the suspected fire locations. This drilling and trucking caused costly delays in the timing of the fire fighting effort, and was not as precise as desirable. Emergency purchasing of gas and pumping services was extremely expensive, running as high as $70,000 per day at one mine. As a result of the experience of other western US coal operators, and the risk inherent with spontaneous combustion at SJCC, it was decided to pursue installation of a nitrogen delivery facility on-site at SJCC. This decision was later expanded to include a continuous supply of nitrogen.

Jan 1, 2005

By T. R. Paquin

Powerful, easy to manipulate, ventilation modeling software is readily available to most mining engineers. Too often when preparing an initial ventilation model, engineers will go overboard in their design, creating a complex model with hundreds of branches. When, in practice, the creation of a less complicated ?to the point? model, containing a few well-constructed branches, would have delivered the same results. In this paper the author will demonstrate, by using actual feasibility report examples, that when designing a ventilation model, engineers should make more use of the K.I.S.S. (?Keep It Simple, Stupid?) Principle. As mining industry consultants we must continue to improve on, and deliver timely and cost-effective results to our customers.

Jan 1, 2009

By A. More, J. M. Míguez, J. Bullón

In 2000 Ferroatlantica started a project with the aim to develop a new casting machine for silicon and other ferroalloys. Until now, it has been cast more than 25.000 tons of silicon for the chemical and metallurgical market. This system has improved the process yield, productivity and product quality which place?s Ferroatlantica at the top of technology development in this field. After the first presentation of the Ferroatlantica?s casting machine at Infacon X, we would like to show the improvements in the control which have permitted us to increase the lifetime of the copper and to obtain, at the end of the machine, the right product size for the customer avoiding the current necessity of crushing and sizing the lumpy metal. Furthermore, we have improved the system in relation to the obtaining of smaller granulometries at the end of casting machine. Not only is this kind of machine cost competitive for special silicon applications but also for other normal ferroalloys with different specifications of size and thickness.

Jan 1, 2007

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010

By F. G. Horino

This report presents the theory and design of a stiff loading machine used by the Bureau of Mines. The machine incorporates three high-strength steel columns as the restraining member in parallel with the specimen. The theory presented gives the basis of design and the dimensions of component parts of the machine. Laboratory verification of the theoretical stiffness is described using three different setups involving a hydraulic jack and spacers and confirms the stiffness calculations to within 1 percent. Experimental techniques, testing procedures, and special equipment designed for determining the complete stress-strain behavior of NX cores of both hard and soft rock are described. Typical test data are presented as force-displacement curves for two rock types, a marble and a granite.

Jan 1, 1972

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab, Coleraine, Minnesota, to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002 after the development of models for magnetic separators, hydro-separators and fine screens. A project funded by the U.S. Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Minorca plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Concentrator Modeling Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2009

By V. B. Dale

San Manuel has been a modern prodigy from its inception to its present status as a block-caving operation producing 33,000 tons per day. The deposit was discovered, prospected, and developed with modern techniques, and nearly all planning was done from results of an extensive drilling program through an average overburden of 670 feet. The Federal Government had a prominent part in the discovery and primary development of San Manuel. The first 17 holes were drilled by the Bureau of Mines, and discovery of the large, low-grade, disseminated copper deposit is credited to the Bureau. A loan fund of 94 million was granted through the Reconstruction Finance Corporation to the San Manuel Copper Corp. for development of the deposit and erection of concentrating and smelting facilities. Then, while the mine was still being developed, the Defense Materials Procurement Agency contracted to buy a large amount of copper at a pegged price.

Jan 1, 1962

By L. Joncourt, N. Touchard, G. Pochart, C. Perdon

Worldwide, the major Manganese ores can be separated into three different types: ?Oxidized ores (MnO2): in Australia, Gabon, Brazil,?. ?Semi-oxidized ores (Mn2O3): in South-Africa, Australia,?. ?Carbonated ore (MnCO3): in Ghana, South Africa, Kazhakstan?. The other Manganese ores are less rich but can be used locally or in the neighbour countries (China, Ukraina, India?). Since the beginning of the 20th Century, Manganese has played a big role in the steel industry process average usage ratio: 9,5 kg/mt of steel). The recent grow-up of this industry has led to an increase of Manganese ores demand. In parallel, several companies have increased their Manganese ore producing capacity. In this presentation, we explain the link between the main Manganese ores characteristics and the key different factors for an effective and low cost Mn alloys production (HCFeMn and SiMn): ?Chemistry ?Size ?Reactivity Then we will point out the advantages of Comilog ore and Sintec ® usages in various Manganese alloy metallurgical process compared with the other main ores and with the local ores. Some advised formulations for the different kinds of furnaces and alloys will be also discussed.

Jan 1, 2007