Search Documents

By Paul Meadows

This Bureau of Mines report presents operating practices and results of pressure maintenance and secondary recovery by water injection or by water injection supplemented by gas injection. Particular emphasis is placed on the results of water injection, which is the principal oil-recovery method employed in projects covered by this report. No attempt is made to study gas-injection projects or operations that are considered water-disposal projects. Also, this report does not include water-injection projects that have not been in operation long enough to evaluate results. Figure 1 is a map of north Louisiana showing the geographical locations of the projects included in this report. Most of the data used in this study were supplied by unit operators, operating companies, and the Louisiana Department of Conservation. Reservoir information and recovery data are generally those supplied by the operators, but include revisions where deemed necessary.

Jan 1, 1962

By W. Sondermann

"AbstractThe construction of a distribution centre of minerals for a global mining and resources cooperation demanded the control of deformations and displacement of the stack reclaimer facilities on very inhomogeneous subsoil conditions. The variation of quality from soft clay with CPT values below 1 MPa up to rock formations were the challenge in design and execution of all the foundation works.The advanced design considerations were resulting in a barrier wall system to limit the deformations of the up to 40 m deep bored pile of the stacker-reclaimers, whereas the layout of the barrier wall and the stiffness of the elements had a major impact on the residual lateral forces to be absorbed by the bearing structure.IntroductionA large international raw material distribution organisation is currently building an iron ore and pellet distribution centre on the north-western coast of Malaysia. The distribution centre will handle around 90 MTPA (million tons per annum) of iron ore and includes accompanying plants for loading and unloading iron ore and pellets, pelletizing plants as well as corresponding storage space for these raw materials. The total storage space extends about 800m north to south respectively 1400m east to west and is about 200m from the coastline. The project area is located in a wide valley basin, bounded by a range of hills to the north. The existence of soil with low bearing capability in the area designated for the plant meant that measurements for ground improvement were required in the storage areas, in order to combine the needs of iron ore and pellet storage areas with requirements of the loading facilities as the overall project demand.Project LayoutThe iron ore distribution centre and the pelletizing facility both consist of an import/export jetty, material handling facilities, pellet plant and the associated infrastructure. This publication describes the execution of ground improvement and foundation works for the loading and storage system, which consists of five rows of stockpiles and four intermediate rows of stacker-reclaimers. The total area of these systems comprises 278,881 m2 (Fig. 1)."

Jan 1, 2014

By Jean R. Garcia, Paulo J. R. Albuquerque, Renato P. Cunha, Osvaldo Freitas Neto

"Abstract Results obtained from in-situ load tests carried out on drilled displacement piles sunk in a porous, lateritic and unsaturated soil deposit, are analyzed in this paper. Three slow-maintained load tests were performed on deep instrumented piles with a diameter of 0.37 m and around 12 m long. The soil deposit consists of a superficial, silty clay “porous” layer 6 m thick, with an average standard penetration blow count (NSPT) of 4 and cone tip resistance and sleeve friction (qc and fs) of 1.5 MPa and 48 kPa, respectively. Under this layer there is a residual stratum 10 m thick, geotechnically consisting of a “porous” clayey silt with an average NSPT of 7 and qc and fs of 2.4 MPa and 202 kPa, respectively. The water table was reached at a depth of 17 m below ground level. The results of the field load tests yielded a maximum pile load (average for the tests) of 1428 kN, which is twice as high as corresponding experimental values from standard bored piles with similar geometric conditions. Exhumation of one of the tested piles was carried out after the test, in order to check integrity and shaft conditions. Numerical finite element analyses, using the commercially available French Code LCPC Cesar®, were performed in order to back-analyze the geotechnical soil parameters for a post execution pile condition. The results permitted a better understanding of the improvement of the subsoil given the intrinsic execution characteristics of this particular pile. It was also possible to note that drilled displacement piles have great potential to become an economically viable solution in tropical soils, given the enhanced behavior of such piles when compared to alternative (cheaper) techniques. In fact, it has several advantages which should make it a key foundation type in the Brazilian market in the future.IntroductionMost buildings in tropical soils use, as the main type of foundation, deep bored or auger type piles. These types of foundations can be performed in various ways, for example with or without soil extraction, with or without bentonite mud and so on. Two main processes maybe formulated: the first execution process is typified by bored pile types, continuous flight auger piles etc., which do not cause excessive soil displacement during excavation. With respect to the second process, one could mention, amongst others, driven piles (precast concrete or steel), Franki piles and drilled displacement piles, which do displace the soil during excavation by pushing the soil laterally around the hole in order to allow either the penetration of the pile or the excavator auger."

Jan 1, 2014

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

By Tano Balbin, Valery Astakhov, Juha Timperi, Lauri Koresaar

"Online elemental analysis is the basis of optimal flotation control in mineral concentrator plants. Traditionally XRF analyzers have been used as the online analysis method. However, online XRF analyzers struggle to measure elements below calcium in atomic number (Z=20). For many processes lighter element assays would be beneficial to improve control of grade and recovery. Processes where elements below Ca are required include P, Mg and Si in phosphate concentrators, Si, Mg and Al in iron concentrators, and S and C in gold concentrators. Laser-Induced Breakdown Spectroscopy (LIBS) based elemental analysis can readily be applied to these processes. LIBS is based on generating plasma in the slurry sample by a high energy laser and analysis of the plasma by optical emission spectroscopy. Capabilities of a new Courier® 8 analyzer based in LIBS technology are demonstrated for elemental analysis starting from lithium (Z=3). Results of a plant installation in a sulfide gold concentrator provide a good agreement with the analyzer and laboratory assays.IntroductionEffective process control can be regarded as one of the fastest paying investments for a mineral processing plant. Process optimization in flotation circuits requires constant feedback of the process state. If only manual laboratory samples are available, this optimization becomes difficult due to the long delay between taking the sample and acquiring the laboratory result. If the element grades are available in online basis, the operator or automatic process control system can make corrective actions in real time.Online X-Ray Fluorescence (XRF) analyzers have been in use at concentrators for decades. The XRF analyzers can provide a fast, accurate and precise analysis from slurry streams. However, the drawback of XRF analyzers is their lack of capability to measure elements below Ca (Z=20) in atomic number. The low energy X-rays of the low atomic number elements get absorbed by water in the sample, protective window of the analyzer, or air between the sample and spectrometer."

Jan 1, 2017

By Richard H. Spencer

The purpose of this program was threefold: (1) to identify the symptoms of poor or inadequate performance of trolley carrier phone systems; (2) to assess the root causes of performance difficulties and classify them on the basis of equipment, coupling, or transmission; (3) to propose, analyze, test, evaluate and verify means of overcoming performance difficulties. Based on interviews and discussions with knowledgeable persons, laboratory experiments, and in-mine measurements, it was determined that the major impediment to good carrier phone system performance is the extreme signal attenuation found on the trolley wire/rail largely due to the many bridging loads. Three means are identified to help overcome the performance difficulties: the low impedance trolley wire, a method of improving performance by capacitively loading the transmission line; the dedicated wire, a low-loss means of extending trolley signal coverage; the use of isolators to remove the offending bridging loads at the carrier frequency. Other subjects treated in the report are design reviews of hardware, guidelines for the use of information in the report, recommendations, and a description of a probe for measuring trolley wire current.

Jan 1, 1977

As part of its research on advanced mining technology, the U.S. Bureau of Mines emphasizes studies on in situ leach mining. This research enables the Bureau to develop technical information that can allow mining companies to adopt in situ leach mining methods. Research results should help to remove the technical and economic barriers currently hindering the development of commercial in situ leach mining operations. This report contains papers summarizing results of Bureau research on various aspects of in situ leach mining. A featured topic is the cooperative field experiment of the Bureau and Santa Cruz Joint Venture in a copper deposit near Casa Grande, AZ. Discussions in-clude an overview of the entire project, cost modeling, environmental permitting, laboratory core-leaching experiments, petrographic studies, and an evaluation of the geologic structure in the region. In addition, papers describe hydrologic modeling and geophysical studies of solution flow during leaching. Preliminary geochemical modeling studies are also summarized. A final paper describes a nonionic chemical additive with potential for significantly reducing the high costs of drilling in in situ leach mining.

Jan 1, 1989

By Rosaire Emond

Le concept du forage horizontal a été développé voilà de nombreuses années. Différents types de plate-formes permettant le forage horizontal depuis une cheminée ont été conçus par divers manufacturiers ou opérateurs miniers. Entre autres, on connaît bien la griffe de montage Alimak à laquelle peut être fixée une plat-forme sur laquelle est montée une foreuse. En 1992, Ross-Finlay a développé sa propre plate-forme de forage qui à notre opinion améliore la flexibilité du concept du forage horizontal, en augmente la productivité et en diminue le coût d?ensemble tout en assurant une sécurité accrue des travailleurs. Tel que montré à la figure 1, la plate-forme employée à la Mine Kiena est composée d?un toit de protection contre les chutes d?objets et de deux passerelles de forage de forme carrée. Le toit et les passerelles sont fixées à une structure de 6.5 m de longueur équipée de deux assemblages de rouleaux (non montrés à la figure) permettant de faire glisser l?ensemble sur des rails Alimak. L?angle du toit et des passerelles peut être ajusté pour des cheminées dont le pendage varie de 65 degrés à 85 degrés.

Oct 1, 2001

By Donald W. Ross

"INTRODUCTION Sponge iron has been made commercially since 1912 at a Swedish ceramic plant; and the product, known as Swedish disk—type sagger sponge iron, has an excellent reputation as a superior furnace feed wherever high—grade steels are made. The general procedure for making brickyard sponge iron was described frequently in Swedish technical journals prior to 1932 and at that time consisted in filling clay refractory containers, called saggers, with a super-concentrate of Gellivare magnetite plus the necessary amount of solid reducing agent and desulfurizer and then firing in a Hoffmann ring furnace, as used in the ceramic industry.The early Swedish publications describe two types of brickyard sponge iron: (1) An inferior high-sulfur product obtained by mixing the ore and reducing agent, and (2) a high-grade low-sulfur product in the form of coherent disks 7 to 9 inches in diameter and 1 to 1-1/2 inches thick made by the saggers with alternate layers of solid-fuel reducr and of uniaxed ore."

Sep 1, 1945

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

Jan 1, 2006

By P. H. Morris

To achieve the full potential of sub-aerial co-disposal the properties of the co-disposed wastes must be known and understood. A description is given of the morphology and properties of waste deposits that were formed during 19 field trials of sub-aerial co-disposal at the dual Goonyella-Riverside mine in Queensland and at Hunter Valley No.1 and Warkworth mines in New South Wales

Jun 19, 1905

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

By Scott A. Walker, Frank L. Rollo

"The San Francisco Museum of Modern Art (SFMOMA) in downtown metropolitan San Francisco, California, is supported on a mat foundation. Although the mat foundation of the original museum was designed to accommodate a future expansion, the plans for expansion that developed in 2010 required a larger footprint to accommodate the new space requirements of the museum. The new, larger expansion was designed by lead architect Snohetta. It will be a tall 12-story, steel-framed building occupying an area that was once the eastern part of the existing museum as well as two adjacent and newly acquired parcels.As designed, the expansion includes a 30-foot-deep excavation which is surrounded by adjacent buildings and improvements. Because of variable subsurface conditions at the site, geotechnical challenges included mitigating anticipated differential settlement between the existing and new foundations, preventing overstressing of the existing mat foundation, controlling groundwater to prevent settlement of surrounding improvements, and providing temporary support of adjacent structures during excavation for the new basement.To address several of the geotechnical challenges, soil-cement mixed (SMX) ground improvement was recommended by Treadwell & Rollo. However, during contract negotiations and construction, the specialty contractor proposed using jet grouting as an alternative technique for ground improvement. The jet grouting approach was accepted in principal, but when implemented was only marginally successful. Accordingly, the contractor eventually installed SMX panels using a Cutter Soil Mixing (CSM) machine. Because the CSM machine was a late arrival during construction, the contractor was not able to take advantage of the ground-improvement technique to install many of the shoring elements that we had originally recommended (such as the cut-off shoring wall). In the end, SMX panels were installed as ground-improvement beneath the new mat foundation to (1) reduce the potential for liquefaction in clean sand below the groundwater by providing increased rigidity to the soil, (2) reduce the potential for disturbing a weak underlying marsh deposit during construction, and (3) transfer vertical building loads to a layer of underlying dense sand.This paper also discusses the quality control and quality assurance programs that were implemented to check that the ground-improvement techniques used were thorough and complete and provided the required strength to transfer the new foundation loads to the underlying strata."

Jan 1, 2014

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980

By Philip K. Hopke

A systematic study of the mechanism of interaction of 218Po(RaA) armed by the decay of 222Rn with airborne particulate matter has been made. The rate of attachment of RaA to particles in the diameter range of 0.1 µm to 10.0 µm has been measured as a function of particle size, concentration, and composition, radon concentration, time of interaction, relative humidity and temperature. It was found that under the conditions in these experiments the attachment rate was proportional to the square of the particle diameter and varied with temperature and relative humidity. The composition of the particles apparently has no effect on the attachment. The variation in attachment rate was related to a sticking probability coefficient of approximately 0.02 that varies systematically with temperature and humidity. In addition, the rate of deposition of RaA on the wall of the attachment kinetics system was measured and also found to change with temperature and relative humidity.

Jan 1, 1980

By I Thin, L Morizzi, C Seymour, G Mungur

Olympic Dam has been investigating mine design options for the South Mine Area (SMA), which will continue using the existing sublevel open stoping (SLOS) method. The SMA is an undeveloped mining area, located south of the existing underground mining areas currently in production at Olympic Dam. The SMA study reached the stage where geotechnical inputs were required for stope design, infrastructure location and ground support forecasts. A large database of geotechnical data was collected to inform open pit designs for the ODX (Olympic Dam expansion) project (resulting from 659 drill holes). This geotechnical data has since been reprocessed to align with design inputs required for the SLOS mining method. The result has been the construction of a preliminary three-dimensional mining rock mass model (MRMM) that has been incorporated into preliminary stope mine design and infrastructure layout assessments, which have taken into account the predicted prevailing ground conditions.As with any model, it is necessary to improve the confidence in its predictability; therefore the model must be calibrated. The preliminary SMA MRMM was no exception. First pass calibration was possible with results from underground geotechnical window mapping from exposed rock mass conditions in the lateral development and surface geotechnical holes for ventilation shafts.The SMA project continues to advance and has started a program of resource drilling. Selected holes have been identified that target data limited areas. This will ensure that the data gaps are infilled in order to maintain the required data density required to improve the model confidence. In addition, further underground window mapping in the SMA will provide ‘mine scale drill hole’ data that can be used to either update the MRMM or as part of planned future calibration. Stope performance data from stopes will provide further valuable data for calibration purposes.The proposed paper will present the process and findings that have been followed in order to establish a well calibrated geotechnical model that can be used with an acceptable level of confidence in the ongoing refinements of the mine design and planning process for the SMA.CITATION:Thin, I, Morizzi, L, Mungur, G and Seymour, C, 2016. Building and calibration of a geotechnical model for sublevel open stope design at Olympic Dam, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 523–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The 18th annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held on Saturday, Dec. 2, 2000 at The Westin La Paloma in Tucson, AZ. The 2000 inductee, guest of honor and featured speaker at the banquet will be Ronald C. Cambre, chairman and chief executive officer of Newmont Mining. He will be honored for his role in positioning Newmont as an innovative and key player in the gold mining industry.

Jan 1, 2000

By Robert G. Harris

During the last five years there have been significant improvements in face support monitoring techniques particularly in respect of face pressure. The measurement of support loading pressures was originally conceived as a maintenance aid for the hydraulic systems but recent work has also included geological loading displays of the complete face as well as individual supports. This paper briefly examines the means of obtaining this information, together with some examples of actual face data. Also included is a summary of the benefits of such monitoring and an outline of future development work.

Jan 1, 1993

By J. Moore, D. Gault, R. V. Lugn

Impact of small projectiles with velocities between 0.9 and 7.3 km per sec on basalt produce craters chiefly by the ejection of fragments. Weight-size distributions of the ejecta are linear for part of the size range of the fragments. Cumulative weight-size distributions of the ejecta from different craters vary because of erratic formation of large fragments and a large percentage of ejecta below 0.1 mm. In the range of velocities studied, the crater depth is approximately proportional to the 0.75 power of velocity of the projectile. This relationship may represent a transition regime between the fluid impact regime and the undeformed projectile impact regime. The volumes per unit of projectile energy of the craters produced are comparable to those reported for lower speed projectile impact and drill bits. An experimental investigation of projectile impact on rock is being conducted jointly by the Ames Research Center of the National Aeronautics and Space Administration and the U.S. Geological Survey. Projectiles are launched with light-gas guns at the Ballistics Range of the Ames Research Center. The craters and ejecta produced in these experiments are being studied by the U.S. Geological Survey. Steel, aluminum and polyethylene projectiles weighing from 0.25 to 0.015 g were accelerated to velocities of 0.88 km per sec (2,900 fps) to 7.3 km per sec (24,000 fps) with a light-gas gun, using hydrogen as the propellant medium. Projectiles impacted the targets normal to plane rock surfaces in an atmosphere of air with a nominal pressure of 25 to 50 mm of mercury. The metal projectiles were mounted in supporting four-piece nylon sabots, which guided the projectiles down the launching tube. After launch, aerodynamic drag acted to separate the sabots from the projectiles. Impact velocities were determined with time measurements and spark photographs of the projectiles in flight. Ejecta were collected in lucite and aluminum containers placed around the target block. A small hole in the containers permitted projectile entry. Impact of projectiles of the size employed produced craters in the rock targets chiefly by ejection of fragments. The craters are small, roughly conical depressions with crushed and intensely fractured rock at the bottoms of the depressions. The ejecta are composed of pieces of the projectile and rock fragments ranging in size from a few tenths of a micron or less to several centimeters in maximum dimension. In this paper, the structural features of the craters, the weight-size distributions of the recovered ejecta, and crater depth and crater volume relationships are described. DESCRIPTION OF CRATERS Typical craters (Fig. 1) produced by experimental projectile impact in basalt are shallow, wide base

Jan 1, 1963

By C. Tan, C. Detournay

Wellbore stability is a major concern for drilling in naturally fractured formations. The infiltration of drilling mud into the fractures is a factor, which may compromise wellbore integrity due to the loss of strength experienced by the fractures. The reduction in the fracture frictional and cohesive properties is attributed to weakening of the infill materials and lubrication of fracture asperities by the mud filtrate. One way to investigate the influence of mud infiltration on wellbore stability in fractured formations is to use a numerical modeling approach. A requirement for the numerical model is the ability to predict the region of mud infiltration. This paper describes a numerical technique to model the extent of mud infiltration for application in coupled fluid-mechanical simulations in densely fractured rock masses using the computer code, UDEC. Several factors are considered including fracture pattern, in-situ stresses, reduction in joint frictional angle and cohesion, viscosity of the mud filtrate and fracture plugging. Results of numerical simulations are presented to illustrate the technique and show the influence of these factors on the extent of mud infiltration. Un des problèmes importants posés par le forage en milieu fissuré saturé, est celui du maintient de la stabilité du puit. L’infiltration de boue de forage dans le massif peut avoir pour effet de réduire les propriétés frictionnelles et cohésives des fractures et de compromettre ainsi la stabilité du puit de forage. Le radoucissement des propriétés des fractures est attribué à la dégradation du materiau de remplissage et au pouvoir lubrifiant des boues. L’analyse numérique offre un moyen d’investiguer l’influence jouée par l’infiltration de boue sur la stabilité du puit. Un des critères de sélection du modèle numérique sera son pouvoir de prédiction du domaine d’infiltration de boue. Cet article décrit une technique numérique permettant de modéliser l’infiltration de boue de forage dans le cadre de simulations hydro-mécaniques, en milieu à haute densité de fractures, effectuées avec le logiciel de calcul UDEC. Parmis les facteurs tenus en compte, on trouvera la nature du réseau de fractures, les contraintes in-situ, le radoucissement en friction et cohésion des joints, la viscosité de la boue et le bourrage des fractures. Des résultats de simulations sont présentés pour illustrer la technique et montrer l’influence de ces facteurs sur la taille du domaine d’infiltration de boue. Bohrlochstabilität ist ein wichtiger Aspekt für das Bohren in geklüfteten Gebirgsformationen. Das Eindringen der Bohrlochstützflüssigkeit in die Klüfte kann die Bohrlochintegrität wegen des Verlustes der Festigkeit des Kluftsystems gefährden. Die Reduktion der Reibung und kohäsiven Eigenschaften ist der Schwächung der Kluftfüllung und der Schmierwirkung der eingerungenen Stützflüssigkeit in Bezug auf die Kluft-Asperities geschuldet. Numerische Berechnungen sind ein Weg zur Untersuchung des Einflusses der Infiltration der Bohrlochstützflüssigkeit auf die Bohrlochstabilität in geklüfteten Gebirgsformationen. Eine Voraussetzung für numerische Modelle ist die Fähigkeit den Bereich der Infiltration der Stützflüssigkeit zu prognostizieren. Diese Publikation beschreibt ein numerisches Verfahren, um die Reichweite der Infiltration von Stützflüssigkeiten mittels fluid-mechanisch gekoppelter Simulationen im engständig geklüfteten Gebirge mit dem Programm UDEC zu modellieren. Verschiedene Faktoren, wie Kluftmuster, Gebirgsspannungszustand, Reduktion von Kluftreibungswinkel- und kohäsion, Viskosität der Stützflüssigkeit und Rissabdichtung wurden untersucht. Ergebnisse numerischer Simulationen werden präsentiert, um die Vorgehensweise zu illu

Jan 1, 2003