Search Documents

By C. Musingwini

The subject of optimal planning of level and raise spacing for inclined narrow reef deposits has received intermittent attention over the years because the subject matter is inherently complex. Previous work has approached the problem as simply that of simultaneously minimizing the total excavation and haulage cost associated with the development workings. However, when level and raise spacing are altered, other factors such as productivity are negatively affected, thus requiring a delicate trade-off of contradicting planning or optimization criteria. The paper concludes that the problem is actually of the multi-criteria decision analysis (MCDA) type, contrary to traditional thinking that the planning problem is achieved solely by minimizing waste development.

Jan 1, 2010

By Scott C. Vollmer

This paper seeks to examine some of the technical factors influencing the deflection of Mechanically Stabilized Earth (MSE) retaining walls based on the authors' field observation of numerous structures. Excessive deflections can be unsightly and can be perceived as wall failure. Deflections can cause cracking or gapping of the facing units and general misalignment. Deflection of the reinforced backfill zone behind the wall face can result in settlement of the backfill zone and adjacent pavement cracking. Deflections can be the result of excessive movement external or internal to the reinforced soil structure. This paper only examines internal factors affecting wall deflections. External factors such as foundation settlement are not discussed.

Jan 1, 2003

By Paul C. Schmall, Lucian P. Spiteri, Arthur B. Corwin

Moving groundwater is generally recognized as the most adversarial condition for ground freezing. Moving groundwater can occur due to natural or man-induced groundwater flow, but either way may result in freeze formation difficulties. History has shown that if the condition goes undetected, catastrophic failure of the frozen shaft or excavation can occur. The success of ground freezing under potentially flowing groundwater conditions depends on an evaluation of the likelihood for this condition; an accurate and early diagnosis, with a careful evaluation of freeze pipe temperatures and piezometer water levels; and timely reaction to mitigate the possible delays. Successful remedial measures have included the reduction of ground permeability by modifying the soil properties between the freeze pipes with various kinds of grouting, or increasing the freezing effect by adding freeze pipes and/or the use of liquid nitrogen as the freezing agent.

Jan 1, 2007

By A. E. Lewis

Particle morphology is a term that is used to describe the overall external shape and appearance of particulate solids. From the physical point of view, a precipitated solid is characterized primarily by the size and morphology of the particles (Sohnel andGarside, 1992). If the morphology of the crystal structures is to be related to the processing conditions, then the morphologies need to be quantified in some way. This can be achieved by using surface area measurements as well as fractal dimensions. The key idea is that rugged and indeterminate systems can be described by using a fractional number that describes the ruggedness of the system (Kaye, 1989). In other words, when the complexity of a structure, such as an agglomerate, increases with increasing magnification, it is useful to employ fractal dimensions to describe the structure. Fractal geometry proposes that, instead of attempting to measure the length of an irregular boundary, the rate at which the length of the boundary approaches infinity with increasing resolution should be calculated. Cross-sectional profiles of rugged particles can thus be quantified using the fractal dimension, and a measurement of the ruggedness of the morphology obtained. One of the additional uses of measuring the fractal dimension is that the measured value can be related to the physical properties and formation characteristics of the particle (Kaye and Trottier,1995). The morphology of nickel crystals was quantified with fractal dimension calculations of particle cross-sections. Particle cross-sections were obtained by mounting the particles in resin and polishing back. These were then photographed using Scanning Electron Microscopy and the resulting profiles analysed using the structured walk technique.

Jan 1, 2001

By S. Peterson, E. C. Westman, P. L. Swanson

Coal bumps are brittle, violent failures associated with high stresses and competent host strata. To study bump mechanisms, conditions in the vicinity of a deep longwall mining face in bump-prone strata were monitored using three discrete systems. First, a microseismic monitoring network recorded mining-induced seismic events throughout the mine and surrounding strata. Second, pressure variations and distributions on the longwall shield legs across the face were recorded. Last, tomography surveys imaged seismic transmission properties ahead of the face. Results from the three systems were correlated in an effort to increase understanding of mining-induced stress redistribution and bump potential. An initial, one-week study showed that the correlation between averaged tomogram values and seismically active areas had a coefficient of correlation (R) of 0.89. Further results of these studies demonstrate that the tomography system is capable of imaging heavy shield-leg loading and bump-prone conditions prior to them disrupting the face operations.

By I Halikia, T Lilis

Lead smelter slags, produced during the last century in quantities ofmillions of tonnes at Lavrion, Greece, have recently been used in theconstruction of Lavrion harbour. In order to evaluate the geochemicalstability of slags and assess their environmental impact on the aquatic environment, a detailed study on lead leachability under conditions that simulate subsea environments was carried out. Leaching experiments using magnesium chloride solutions under mild temperature conditions were conducted and the effect of main parameters on lead solubility was examined. Furthermore, kinetic analysis on the experimental results was performed. Based on the results, lead dissolution increases by increasing the reaction time, magnesium chloride concentration in the bulk solution and temperature, whereas it decreases by increasing the slags particle size. The reaction order was found to be approximately 0.5 at the initial extraction stages and the activation energy value from the Arrhenius plot was estimated to 29.8 KJ/mole. Diagnostic equations applied to all the experimental data reveal that lead dissolution is mainly controlled by diffusion through the ferrosilicate matrix of the slag particles, which is in accordance with the low activation energy value. The JanderÆs diffusion equation [1-(1-a)1/3]2=kt was proposed as the equation representing the reaction of lead dissolution from slags using magnesium chloride solutions.

Jan 1, 1999

The work described herein is the opening phase of an extensive system of underground excavation undertaken under contract with a Malayan authority.The specifications called for the lining of all tunnels in earth or broken rock with circular segmented cast iron lining, similar to that of the London tubes, and it is the installation of these linings which it is proposed to discuss.Owing to the long deferred delivery quoted and the obvious need for speed of access to the internal installation, it was decided to defer driving the completed circular section and substitute two small timbered headings.These could later be opened out in turn to full section and lined without prejudice to traffic, since both of them had access to the internal workings.NATURE OF ROCKThe rock series through which the circular sections were driven consisted of:(a) A wide zone of intrusive porphyritic granite, consisting generally of orthoclase phenocrysts in a ground mass of micro pegmatite. This area showed advanced weathering, varying from a stage showing slightly tinted kaolin containing approximately 20% of small boulders to one of ultimate decomposition to pure kaolin;(b) A narrow zone of weathered augite diorite, consisting of rock masses of a maximum weight of some 100-150 tons, isolated by clay seams up to 1 ft. 6 in. in width.The whole area was in a state of quasi-hydrostatic equilibrium, which resulted in heavy pressure immediately after excavation. Freshly broken faces would appear to be quite solid but, within a few minutes, would commence to sweat and "slab off" under pressure and, unless support was placed promptly, the whole face would burst out and run from above. Mucking was slow, owing to the plastic nature of the clay and the ease with which it puddled into slurry.In zone (b) a good deal of trouble was experienced because of the fact that the somewhat heavy blasting necessary tended to cause movement of the large rock masses. Subsequent scouring out of the supporting clay bands by the waterflow permitted settlement of the ground on to the timbers and many reinforcing sets were therefore required.The timbering of the pilot headings and its relation to the cross-section of the circular tunnels is shown in Fig. 1. Top and side spiling was driven in the ordinary way, but in bad ground intermediate sets and breast boards had to be placed. These sets were usually withdrawn after the...

Jan 1, 1941

By Robert B. Bittner

"AbstractLarge diameter tubular piles offer significant advantages in terms of design performance and economy for major marine structures. This is particularly true for foundations of major overwater bridges in regions of high seismicity such as the west coast of North America. The use of large diameter piles in the range of 2 to 3 m diameter means that fewer piles are required, and the size and mass of the pile caps can be significantly reduced, thereby greatly reducing lateral load demand during seismic events. Another advantage of using larger diameter piles is increased pile stiffness that allows the pile caps to be located at or near the waterline rather than being positioned at or below the mud line. This elevating of the pile cap offers significant cost savings by eliminating the need for deep cofferdams. However, relocation of the pile cap creates new problems and opportunities in regard to the means and methods used to construct the pile cap. With the pile cap at depth, conventional steel sheet pile cofferdams with thick tremie seals are typically used to isolated the cap location and allow dewatering for construction of the cap. However with pile caps positioned up off the bottom, conventional bottom founded cofferdams are no longer cost efficient. Float-in or lift-in cofferdams have been developed to address the need for a more cost efficient method for cap construction. This paper describes the key features of the concept and provides three case history examples of its successful implementation.Pier Construction Using Conventional Sheet-Pile CofferdamsCofferdams are temporary structures used in the construction of bridge piers and other marine structures. Their primary purpose is to hold out water and unstable soil from the construction area, and thereby, allow in-the-dry construction of the permanent structure below the water line and quite often below the mud line. Typically, cofferdams consist of long interlocking steel sheet piles driven through water into the bottom of the waterway. The sheet piles form temporary exterior walls which are typically braced internally with wales and struts. The bottom of the cofferdam is typically sealed with tremie concrete or an impervious clay layer if one exists. The depth at which this type of cofferdam can be used is typically limited by the length of steel sheet pile that can be transported and handled by conventional marine equipment."

Jan 1, 2014

By A H. Clemens, P Lindsay

Acid producing potential static tests have been undertaken on sample lithologies from New Zealand coal mines, to rank the lithogies into acid producing waste rock and stable non-acid producing waste rock. Results indicated that the main acid producing waste rock in the Waikato coal region are the marine Whaingaroa siltstone and the Glen Massey formations and the main alkaline producing lithologies were the Tauranga group volcanic-derived sediments (A & D) and the Mesozoic basement. Coal ash analysis of 28 samples from 28 mines have also been analysed for reactive S percentage and their base potential has been quantified by the chemical index of alteration (CIA). The results provide mine management in the Waikato Coal region with a classification of problematic and stable waste rock types. XRF and CIA values determined from wash drill cuttings would provide a method of determining waste rock volumes and magnitude of palaeo-weathering underground.

Jan 1, 1999

By J Widjaja, E Hermawan, M Muharam, L Damanik

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The island of Java lies within the Sunda-Banda magmatic arc, which is characterised by multiple phases of volcanic activity and extensive compressional deformation. Along this zone, significant gold and copper mineralisation occurs, including some of the world’s largest deposits. In West Java, epithermal gold mineralisation is typically located in a series of extensional and strike-slip faults that cut Miocene to Pliocene volcanic rocks. These are all low-sulfidation, epithermal, vein-stockwork-style deposits developed in Miocene to Pliocene calc-alkaline volcanic rocks, which have been intruded by shallow-level plutons.This paper discusses an example of epithermal mineralisation at Mt Subang, West Java. Gold mineralisation was originally identified from stream sediment, panned concentrate and rock geochemistry sampling in the early 1990s. Geophysical surveys (magnetics and induced polarisation resistivity/chargeability), trenching, pitting and diamond hole drilling has subsequently revealed silicified-quartz vein epithermal gold mineralisation hosted within fault structures. It is clear that these structures acted as hydrothermal fluid pathways leading to the development of mineralised offshoots along north–south extensional and en-echelon arrays of north-east–south-west and transtensional faults. A number of vertical offshoots also occur in flexures and fault jogs. Post-mineral faulting has subsequently dissected and offset a number of the offshoots. Therefore, a detailed knowledge of structure and fault kinematics and displacement magnitudes is required in order to understand the geometry and continuity of mineralisation across major structures and maximise the resource potential. A range of exploration targets were modelled, indicating a minimum and maximum of 0.2 and 1.8 Moz of gold respectively.CITATION:Cunningham, M J M, Muharam, M, Damanik, L, Hermawan, E and Widjaja, J, 2015. Structural controls on the localisation of low-sulfidation epithermal mineralisation in West Java, Indonesia , in Proceedings PACRIM 2015 Congress, pp 227–234 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J. Olsson

Introduction Stainless steel has by tradition been a common construction material for hydrometallurgy processes and the most common grades can be found amongst the ASTM 300-series, i.e. austenitic grades of type 304L, 316L and 317L. However, there are a number of new grades available today, which imply more cost effective solutions for those designing plants where good resistance to acids, containing the desired metal ions, often contaminated with chlorides and other halides, is the key issue. There are austenitic-ferritic or duplex grades having the same or even better corrosion resistance than the austenitic grades and approximately twice the strength, which enables design in thinner gauges, which in turn implies less weight and less cost. They have also excellent engineering properties, enabling fabrication of process equipment, machinery and different types of tanks. On top of that, they contain less nickel and molybdenum than their austenitic counterparts, which implies not only lower cost for alloying elements, but also a more stable price when considering the price fluctuations for these alloying elements during the last years. This paper describes briefly the family of duplex stainless steel and it presents a number of relevant corrosion tests where duplex grades have been compared with austenitic grades. The results have in several cases been verified by in-plant exposures in zinc and copper production plants. It also describes applications and experience of duplex grades within a variety of hydrometallurgy plants. Installations of highly alloyed austenitic grades will be described as well. The corrosion tests and service experience reported cover hydrometallurgical processes based on sulphuric acid.

Jan 1, 2007

About 15 per cent of total electricity (400 MkW) was generated by nuclear power plants in the world (2009) and about 36 000 tons of uranium has been mined in uranium mines annually. Radioactive waste material is produced from uranium mines and nuclear power plants. The wastes must be disposed or stored safely for long-term. If they leak and/or move from disposal or storage sites due to air/groundwater flow, then a serious environmental pollution can occur. Hence, multi-layer system has been proposed and employed in order to seal off these radioactive waste materials from biosphere. Basically, bentonite is now used for establishing absorbing and sealing layers in this system. However, the amount of high quality betonite is very limited and in some cases it is hard to be obtained.On the other hand, a great deal of refuse from coal burning plants is produced every year and the amount of it is expected to be higher each year, especially in developing countries. More than half of flyash is utilised and the remaining is disposed at the disposal sites. However, the life of the disposal site is limited and it is diff cult to find a new disposal site. It is requested that the percentage of the utilisation of the flyash be increased in every field.From the above two points of view, a flyash-based barrier layer/cover system is considered in this research and this paper discusses the applicability of flyash as a content of barrier layer/cover material based on the results of a series of laboratory tests.

Dec 6, 2010

By D. E. Wolfson

As part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Raleigh County in beds 28 inches or more thick, in thousand tons, is: [ ]

Jan 1, 1957

By V. Brabie, S. Jansson, L. Bohlin

The rate of dissolution of solid MgO-C and doloma into liquid in CaO-Al2O3-SiO2-MgO slag at different temperatures was studied under conditions of forced convection by rotating cylindrical refractory specimens in a stationary crucible containing the molten slag. The corrosion rate was calculated from the change in diameter of the cylindrical specimens. Refractory specimens were 13 mm in diameter and 70 mm long. The specimens were rotated for15 to 120 minutes at speeds of 100 to 400 rpm in the molten slag. The rate of corrosion increased with temperature and with the rotating speed of the rod, and decreased when the slag was nearly saturated with MgO. The experimental results confirm the assumption that the diffusion of magnesium oxide through the slag phase boundary layer controls the corrosion process. The corrosion mechanism seems to be the dissolution of the refractory materials into the slag, followed by penetration of pores and grain boundaries and dispersion of the grains in the slag. Keywords: MgO-C refractory, doloma refractory, molten slag, corrosion rate, corrosion mechanism

Jan 1, 2004

By S. Banisi, J. Marois, A. R. Laplante

"This paper compares the behaviour of gold and ore in the grinding circuit of Hemlo Gold Ltd. Particular attention is given to grinding kinetics, classification behaviour, and liberation. For grinding kinetics, laboratory grinding of gold flakes and silica, 840-1200 um in size (14/20 mesh), was also performed to provide a standard for comparison and to study in a controlled environment the mechanisms of breakage, folding, smearing and impacting.Grinding kinetics were characterized at laboratory scale with breakage and selection functions. The breakage function showed that 75% of gold disappearing from the 840-1200 um class reported to the 600-840 um; this figure is much higher than for silica ( 46%) or most other minerals, and implies that comparatively fewer fine fragments are produced from the breakage of gold flakes, on account of gold's malleability. The selection function of silica was four times that of gold. At plant scale, the ratio of the selection function of ore and gold increased from 6 for at 50-100 um to 20 at 500-1000 um.Observation of original flakes and their fragments with the scanning electron microscope showed that the main mechanism of ""grinding"" from the 840-1200 um to the 600-840 um class was folding rather than actual breakage. This was confirmed by a measure of individual flake weight. The postulated breakage cycle is that relatively globular flakes become increasingly serrated through grinding; they can then regain their original shape through folding and reflattening into cylindrical and spherical shapes, as the majority does; however, some fragments will at this point undergo actual breakage. Photographic evidence is presented to support the proposed mechanisms.Smearing of gold unto silica was observed when silica was ground after a gold, and embedding of silica into gold flakes when gold was ground after a silica. Both mechanisms occur whenever gold and harder minerals are jointly ground, and result in ""unliberation"" of gold. It is postulated that smearing of gold onto other minerals plays an important role in explaining how gravity recovery can increase overall gold metallurgy, especially when used ahead of flotation.Classification of gold in the primary hydrocyclones takes place at a much finer cut-size than ore, 20 vs. 57 um. This and the slower grinding kinetics result in high gold circulating loads in the primary loop, 6700%, and a gold content in the primary cyclone underflow (PCUF) is twenty four times that of the ore. The gold size distribution for primary cyclone overflow is much finer than that of the ore, although they are essentially similar in the PCUF.Liberation, or more accurately ""gravity recoverability"", was assessed with a 7.5 cm (3"") Knelson concentrator. It varied between the thirties for the primary mill discharge and two cyclone overflows, to highs of 89 to 92% for the PCUF and secondary mill discharge, 89 and 92%, respectfully."

Jan 1, 1991

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By R. D. Lindsay

Pamour Porcupine Mines, Limited has been actively engaged in the ''Custom Tolling'' of Gold-Bearing materials throughout the past decade. Experience acquired in this area was utilized to design and commission a custom gold milling facility at its operations in Timmins, capable of:(a) Accepting a bulk ore test sample at the rate of 150 t/d for crushing, sampling, and metals analysis;(b) Processing gold-bearing ores at a rated capacity of 150 t/d, to produce a goldbearing sulphide concentrate;(c) Processing free milling gold ores at a rated capacity of 80 t/d for total cyanidation;(d) Cyaniding custom gold flotation concentrates at a rated capacity of 80 t/d; and(e) Processing of complex gold/copper or carbonaceous ores, requiring an impurity flotation concentrate separation stage prior to cyanidation, at a rated capacity of 100 t/d.Items considered in the process design and development included:- various gold ore types available for processing;- flowsheet flexibility required;- sampling strategy as related to head grade determination and metals accounting; and- contract considerations.This paper highlights how these various considerations were used to design Pamour's ''Custom Gold Milling Facility''.

Jan 1, 1987

WHILE in the employ of the Broken Hill Associated Smelters and the Electrolytic Zinc Oompanies at their South Melbourne Research Station, the writer was detailed to investigate the principles underlying the Parkes Process with a view of determining:1. The Interdependence of the variables:(a) Quantity of zinc required per charge,(b) Temperature of stirring of each zincing,(c) Silver content of the bullion after first zinculg,(d) Silver content of the bullion after second zincing,(e) Silver grade of the crusts produced for retorting, with reference to the method of working the Parkes Process then in operation at Port Pirie.2. The possibility of effecting improvements in the Port Pirie practice of desilverising, especially with respect to:(a) Silver grade of the crusts produced for retorting.(b) Quantity of zinc required per charge.The method of desilverising in practice at Port Pirie was a two-stage zincing.In both zincings the bullion was cooled to its solidification temperature and the silver crusts which separated from the lead were completely removed.The crusts from the first zincing were retorted, and the crusts from the second zincing were returned to the first zincing of the next charge.

Jan 1, 1925

By Bradley V. Johnson

This publication summarizes the in-house and contract research and development projects conducted since 1974 by the Bureau of Mines for the control of noise and vibrations from surface mine blasting.

Jan 1, 1982

By A. Jarosz

The surface manifestation of underground mining usually entails five distinct types of surface movements, which can affect or damage surface structures, facilities and renewable resources. These movements developing at the surface can be described by (Bell, 1975; Bhattacharya and Singh, 1984): - vertical displacement, i.e. subsidence, - horizontal displacements, - slope or tilt, i.e. the derivative of the vertical displacement with respect to the horizontal distance, - curvature, i.e. the second derivative of the vertical displacement with respect to the horizontal distance, and, - horizontal strain, i.e. the derivative of the horizontal displacement with respect to the horizontal distance.

Jan 1, 1986