Search Documents

By M. T. Styles, E. Condliffe, R. C. Leake, R. J. Chapman, D. J. Bland

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Quantitative point analysis and microchemical mapping identified 52 different types of mineral in inclusions, usually ranging in size from 5 to less than 1 micrometre, inherited from source bedrock. A combination of grain chemistry, heterogeneity and inclusions provides a grain signature reflecting the type and history of source mineralisation. Several grains from an alluvial site are needed, to allow for bedrock variation and the presence of inclusions in only 10-20% of grains. A total of 1 530 grains obtained from 30 localities in Scotland were of ten types, two of them minor variants. Two types in the Highlands may be related to centres of Caledonian igneous activity, but the most widespread is likely to have been of deep-seated origin and structurally controlled. Gold in the Ochil Hills is probably from a source associated with Devonian andesitic activity. In the Southern Uplands, grain types reflect two separate episodes of mesothermal lode gold mineralisation and relationships with Permian red beds/mafic volcanics and with Tertiary dykes

Jun 19, 1905

By Wilbert T. Malenka

A modified factorial experiment was used to determine the effect of operating factors in hydraulic mining of anthracite. Seven basic factors at various levels were considered. The significant factors were found to be pressure-volume, pattern, and jet traverse speed. Mining data were programed for computer, and a prediction equation was determined from printout information based on the hydraulic "jumbo" operating parameters and characteristics of anthracite, The source of error is discussed. The prediction equation is general in nature and might be useful in delineating performance characteristics in the design of equipment and/or more effective utilization in a medium with characteristics similar to those of anthracite.

Jan 1, 1968

By J. M. Pei

In this paper, the nonlinear finite element analysis is used to study the support system of a tunnel which is designed to pass through deep-embeded stratum. The rock mass is rather intact, though a section of tunnel will pass through the weak belt. Under the influence of the high ground stress, the condition of stability and the form of support become complicate. This paper, talcing into account the nonlinear properties of rock mass and the Interaction between rock, and support, makes a comparison between the two kinds of soft and rigid support systems, and analysed the changes of their bearing forces.

Jan 1, 2010

By T Salles, G Duclaux, E R. Ramanaidou

In a continental environment, sediment mobilisation, dispersion and deposition are mainly controlled by mass gravity and streamflow processes. Alluvial sedimentary systems have an important economic value because of their capacity to host mineral resources. In the Hamersley Province, alluvial iron deposits (including the well-known detrital iron deposits and channel iron deposits) play an increasing role on the commodity market. Alluvial deposits exploration is challenging and generally involves geomorphologic and stratigraphic field studies, as well as expensive exploratory surface sampling and drilling. We applied a new surface processes modelling technique to investigate iron rich material, ie the erosion product of bedded iron formations -dispersion in the Hamersley Province. LECODE is a 3D-parallel surface processes forward modelling code designed to compute surface flow and solve erosion, transport and sedimentation on the geological time scale. The code offers new quantitative ways to better understand how sedimentary deposits develop in intra-continental and channel environments. Here we show that our integrated forward model is capable of opening a window to the construction of sedimentary architectures, including facies distribution, deposit thickness and development of heterogeneities such as mineral traps over the modelled domain. The model results represent 1 Ma of surface evolution and are validated through comparison to published paleovalleys map and known occurrences of iron ore deposits. This numerical modelling approach allows for the first time to track alluvial materials from source to sink through time, test existing geological models and faithfully reproduce the first order distribution of alluvial iron deposits in an area of interest. This work strongly suggests the presence of iron rich alluvial deposits reserves under cover, in unexplored detrital fans in the Fortescue Valley. This method, potentially coupled with sediment geochemistry and basin analyses studies, has the potential to maximise alluvial iron deposits exploration success, while reducing exploration cost and associated environmental impact.CITATION:Duclaux, G, Salles, T and Ramanaidou, E R, 2013. Alluvial iron deposits exploration using surface processes modelling - a case study in the Hamersley Province (Western Australia), in Proceedings Iron Ore 2013 , pp 75-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By B Brown, P J. Hommert, B J. Thorne

"Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. A"" improved damage model based on microcrack growth in tension allows finite elementcalculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model."

Jan 1, 1990

By T van der Meer, A Salokannel, M Martikainen, L M. Nevatalo, J McCulloch

Water use and wastewater management is becoming a focus for many industries around Australia and the rest of the world. Good quality water is increasingly being recognised as a precious resource, and regulations on the bulk storage and discharge of waste streams is becoming more stringent in order to protect the environment, existing water reserves and the communities that use these resources. Components such as heavy metals, arsenic, cyanide, and sulfate from acid mine drainage are some that occur at mining and metallurgical processing sites. Removal of such components can allow safe re-use of these streams, reducing the new water requirements of the process, or else allowing acceptable discharge to the environment. Re-use or discharge of treated water eliminates or reduces the risk associated with storage of large volumes of contaminated water on site.Technologies where a contaminant is selectively precipitated and removed as a sludge are used for many of these treatments. Selection of the best treatment option for wastewater must depend on what is suitable to each site, and consider not only the nature of the contaminant, but also other aspects, including the location and situation of the site, local regulations, cost of reagents, the sensitivity of the local environment and waste sludge disposal options. To outline how an effective and economical solution can be designed and delivered, this paper will present a case study for the removal of arsenic from a site wastewater, from assessment of the problem, selection of suitable technology, design and implementation, to the benefits delivered to the site.CITATION:Salokannel, A, Nevatalo, L M, Martikainen, M, van der Meer, T and McCulloch, J, 2013. Technology selection for removal of contaminants from an industrial wastewater, in Proceedings MetPlant 2013 , pp 531-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Met M. E

In choosing the subject for my address to you this evening I was actuated by the knowledge that in the past Australian metallurgical problems have been solved by the introduction of extremely interesting processes. Frequently such processes originated in this country, or at least were first adopted here on a large scale.Chronologically there comes to mind the application of chlorination to the Mount Morgan ores from 1888 onwards.Then the application of pyritic smelting to the Mount Lyell ore body in 1896, followed closely by the successful flotation of zinc blendÇ! at Broken Hill, about 1900, and the treatment of the refractory Kalgoorlie gold ores by roasting and cyaniding. With the development of the differential flotation process at Broken Hill came the production of a slime lead concentrate carrying zinc which necessitated the use of a high zinc slag in the lead smelting process. Although previously considered impossible, the necessarytechnique was successfully evolved at Port Pirie resulting in the accumulation of large tonnages of zinc-bearing slag as potential sources of that metal. The past twenty years have witnessed:-(a) The establishment of a flourishing iron and steel industry, with its attendant coking and by-product plant at two centres in New South Wales, namely, Newcastle and Port Kembla.(b) The establishment of an electrolytic zinc process at Risdon in Tasmania.*Presidential Address, Melbourne, 20th August, 1936.

Jan 1, 1936

By B. G. Tarasov

This paper proposes the further development of a recently identified shear rupture mechanism (fan mechanism) that elucidates a paradoxical feature of hard rocks ? the possibility of shear rupture propagation through a highly confined intact rock mass at shear stresses that can be significantly less than frictional strength. In the fan mechanism, failure is associated with consecutive creation of small slabs (known as ?domino blocks?) from the intact rock in the rupture tip, driven by a fan-shaped domino structure representing the rupture head. The fan head combines such unique features as extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Consequently, the failure process caused by the mechanism is inevitably spontaneous and violent. Physical and mathematical models explain unique and paradoxical features of the mechanism, which can be generated in primary ruptures and segmented faults. The fan mechanism provides a novel point of view for understanding the nature of spontaneous failure processes, including shear rupture rockbursts. The process explains, in particular, features of shear rupture rockbursts such as activation at great depths, generation of new shear ruptures in intact rock mass, nucleation of hypocentres at significant distances from the excavation, shear rupture development at low shear stresses, and abnormal rupture violence.

Jan 1, 2014

Recovery of Tantalum Capacitors from Waste Printed Circuit Boards Using a Pneumatic Separator

Sep 13, 2010

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By Charlie Wyche

The British Solomon Islands Protectorate continued developmental work on bauxite deposits on the Islands of Rennell and Vaghena. A feasibility study was completed by Mitsui Mining & Smelting Co., Ltd., and Pacific Aluminum Ltd. (a subsidiary of Conzinc Riotinto of Australia Ltd,), and negotiations with the Government were in progress. The Government will receive a 25% share if the project is realized. It was estimated that the Islands contain 60 million tons of bauxite with an alumina content of 45% to 50%.

Jan 1, 1980

By J. F. McIlwain

The Bureau of Mines has investigated fumes generated by selected welding electrodes used in mines in order to help determine their relative health hazard potential. Fumes were generated and collected in an enclosed chamber for subsequent generation rate and chemical constituent determination. Shielded metal arc electrodes from the following groups were tested: AWS types E308-16 and E310-16 stainless steel, ECoCr-A Co-Cr hardfacing alloy, ENiCr Ni, an Mn-Cr buildup alloy, E7018 carbon steel, and EII018-M low-alloy steel. Flux-cored wire electrodes of this last group also were tested. Fume generation rates and the chemical composition of the fumes were measured. From these data, exposure in-dices were determined, which give a relative measure of the health hazard potential of using the electrodes. The effect of welding onto build-up alloy layers on the fume composition also was examined for five of the higher alloy groups.

Jan 1, 1987

By J. Wright

Since the 1960’s toroidal conductivity has been used to determine the Alumina to Caustic ratio of the digester discharge liquor stream. In recent years the application of ceramic materials have allowed the sensors to moved upstream to provide tighter control of the process. In the Bayer process, dissolving the aluminum contained in bauxite ore in caustic soda and converting it to aluminum oxide produces alumina. An important parameter of the process is measuring the alumina to caustic ratio in the digester discharge stream. The A/C ratio at a given caustic concentration is a measure of the degree of saturation of the alumina in the plant liquor. The aim in the process is to achieve a high A/C ratio. There is however a limit where precipitation will occur if the A/C ratio is too high. For many years conductivity has been used to determine the A/C ratio. Conductivity of discharge liquor is related to the caustic concentration. The change in the caustic concentration is in the same direction of the change of solubility of the alumina. Controlling the conductivity through adding additional bauxite ore and varying the dilution flow can increase plant yield.

Jan 1, 2001

This paper gives a general description of mining operations at the Mount Morgan Open Cut. Certain features such as blast hole diamond drilling, which may be of particular interest, have been described in detail. The paper is covered by the following headings:-1. History2. Ore Reserves and Production Data3. Mining Methodsa. Design and Layout of the Open Cut.b. Overburden and Ore Breaking.c. Loading and Transport of Ore and Overburden.d. Transport of Men and Supplies.e. Survey and Assay.f. Drainage.4. Power and Compressed Air5. Mining Equipmenta. Shovels.b. Mine Transport.c. Dozer Tractors.d. Drill Shop.6. CostsHISTORYIn order to appreciate fully the design of the present Open Cut at Mount Morgan, a brief outline of the Mine's history and past mining methods is necessary. In 1882 the Mount Morgan Syndicate began to mine this large gold-copper orebody by small hill-top quarries...

Jan 1, 1952

By Michael Godard, Peter Cleyle

"Suncor Energy’s Project Millennium increased oilsands production capacity by an additional 95,000 barrels per day to its present level of 225,000 barrels per day. This massive venture included an expanded Mine, new Extraction and Upgrading facilities, as well as, steam and utilities infrastructuresIn the Primary Extraction process, removal of the bitumen from the oil sand begins with slurry preparation and is followed by primary , secondary and tertiary separation processes. The final cleaning step of the bitumen froth is the Secondary Extraction process, that removes residual water, mineral and solids to produce a clean diluted bitumen suitable for Upgrader feedstock.This paper will review the flowsheet of the Millennium Primary Extraction facility, from its recent commissioning through the ramp up to design production rates. In addition, new technologies in the Primary Extraction flowsheet will be reviewed.INTRODUCTIONAs conventional supplies of oil and gas are depleted in Canada, the Athabasca oil sands industry of Alberta becomes an increasingly important source of energy. Today, high quality crude from Alberta’s oil sands accounts for roughly 30% of Canada’s daily petroleum production. According to government projections, over the next 7 years, oil sands production is expected to more then double, and by 2010 more than half of Canada’s crude oil is expected to come from the oil sands.Oil sands deposits consist of a layer of sand saturated with bitumen covered by a muskeg overburden and underlain by silt and clay. The oil sand is mined where the overburden is economical to remove, typically less than thirty meters thick. The Athabasca oil sand deposits around Fort McMurrray is ideal for mining. Bitumen can be described as a diverse collection of hydrocarbons, organosulfur, and nitrogen compounds."

Jan 1, 2004

By Hanlong Liu

The construction process and load-bearing behaviors of Cast-in-place Concrete Thin-wall Pipe Piles are analyzed based on its application on Yan-Tong Expressway project. The low strain test, static load test and field excavation are also carried out. It can be concluded that the new type of pile is convenient to construction with high bearing capacity and reliable quality, which has great potential in practical engineering.

Jan 1, 2006

By M. Valdebenito, J. Rajala

An OCS Expert control system was implemented by Svedala Cisa at the Minera Maricunga Refugio Crush-Leach Operation near Copiapo, Chile. The purpose of the Expert system was to maximize production through the primary and secondary crushing circuits and help balance crusher usage between each stage to maximize total plant production. Interesting aspects of the control strategies are discussed. Benefits of the control were verified through a randomized On/Off test program. Tonnage increases ranged from 5% to approximately 20% at good confidence intervals. Benefits analysis results are discussed. The crushing plant at Refugio is very remote and is located at approximately 15,500 ft. This poses many challenges. The effect of altitude and remote location on plant operation are discussed.

Jan 1, 2002

By M. Q. W. Jones

This paper presents a compilation of physical properties of rocks from the Bushveld Complex. The database consists of more than 900 measurements each of thermal conductivity and density. The data are well distributed from localities around the Complex and most rock types are well represented. Thermal conductivity and density are shown to vary widely in the ranges 1.8-4.2 W m-1K-1and 2600-4200 kg m-3respectively. Although only 190 heat capacity measurements are available, this parameter is quite uniform for most rock types present, 800-900 J kg-1K-1, except for chromitite, which has a lower average, 750 J kg-1K-1. Rocks encountered in deep platinum mines are particularly well characterized and this has important implications for prediction of mine refrigeration requirements. The heat flux into a semi-infinite region with properties typical of the Bushveld Complex as a function of time is substantially lower than an equivalent model for the Witwatersrand Basin.

Jan 1, 2015

By A. M. Bryukhanov, A. G. Mnukhin

The report states accident rates for gassy/dusty coal mines represented as an ergatic system "man – machine - environment" with further analysis by the method of conditional probabilities. A coal mine has been analyzed with allowance for the attending personnel, equipment and environment as a sequence of events and states. Probabilities of operational states have been determined and prediction of mine behavior has been made on the basis of investigation findings for equipment and the personnel states, and analysis of the environment (i.e. mine and mining conditions). Utilization of expert estimation methods has been considered for determining major operational parameters of gassy/dusty mines. The importance of standardized values of permissible occupational risks (permissible probability of accident, PA) is demonstrated. It is also stated that a procedure is essential to determine these values, involving regular check-ups of the integral safety criterion at all mines and further development of customized recommendations for individual mines on efficient improvement of accident situations. Methodology to determine the assessment criteria has been developed and scientifically substantiated for permissible accident rates in hazardous industries.

Jan 1, 2003

By G. O. Rading, B. O. Odera, M. J. Papo, R. Couperthwaite

"Platinum-based alloys are being developed with microstructures similar to nickel-based superalloys for potential high-temperature applications in aggressive environments. Since the chemistries of nickel and platinum are similar, Pt-based alloys can be made with gamma prime ~Pt3Al precipitates in a gamma (Pt) matrix. Currently, the Pt-Al-Cr-Ru system is one of the bases for developing Pt-based alloys, where Al allows the formation of thePt3Al precipitate and also gives protection from the alumina scale formed, Cr provides oxidation resistance and stabilization for the L12~Pt3Al phase, and Ru provides solid solution strengthening in the (Pt) matrix. Four Pt-Al-Cr-Ru-V and two Pt-Al-Cr-Ru-V-Nb alloys were made, with compositions based on a quaternary alloy, ~Pt82:Al12:Cr4:Ru2, which hadpreviously been identified as having optimum properties. Four of the as-cast alloys had the targeted two-phase structure of ~Pt3Al and (Pt), and two were single-phase ~Pt3Al. Vanadium partitioned more to (Pt) than to~Pt3Al. There was an improvement in hardness compared to the quaternary alloys. The best addition of V was ~15 at.%; higher additions resulted in brittle intermetallic phases of the Pt-V system. The effect of Nbcould not be ascertained because of its high losses."

Jan 1, 2015