Search Documents

By D. Royston

SAG mill liner development draws primarily on practical experience from SAG milling operations supported by computer-based modeling of charge motion in SAG mills and on established good design practice. Liner design needs to respond to the process aspects of mill liner action that are critical to good SAG mill performance, i.e., the impact of shell liners on the grinding action and of grates and pulp lifters on pulp discharge. In recent years, the trend in large SAG mills has been to use wide-spaced shell lifters with large lifter face angles, primarily to reduce packing and ball/liner damage, and to use larger, hence fewer, mill liner parts to reduce downtime at liner change-outs.

Jan 1, 2007

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

By R. W. Fedors, S. T. Green, G. R. Adams, C. Manepally, L. B. Browning

This paper provides estimates of large-scale temperature gradients that can be used to support modeling of natural convection and cold-trap processes in thermally perturbed drifts. Temperature influences estimates of the quantity and chemistry of water contacting engineered components (e.g., drip shields and waste packages) in a potential high-level waste repository at Yucca Mountain, Nevada. Temperature gradients drive natural convection and cold-trap processes, which could affect the distribution, quantity, and chemistry of liquid-phase water contacting drip shields (waste packages).The confluence of high temperatures, liquid-phase water, and high chloride may lead to corrosion of drip shields and waste packages. An overview of the evolution of environmental conditions in thermally perturbed drifts is presented to provide a context for the estimates of temperature gradients. A mountain-scale conduction-only model is used to estimate temperature gradients and temperature differences for a drift located at the center of a potential repository. Thermohydrologic models and heat transfer algorithms are used to evaluate the reasonableness of the conduction-only results. Estimates of temperature using an in-drift heat transfer algorithm account for the possibility of drift degradation and formation of a rubble pile on the drip shield. Temperature differences between the center and ends of the drift are estimated to rapidly increase to 80 °C soon after repository closure. That temperature difference decreases over time to 15 °C after 10,000 years. Local temperature gradients are generally estimated to be less than 0.2°C/m, though the gradients can be much larger near changes in lithology and near the end of the drift. The estimates of temperature gradients do not account for intermediate- and small-scale variations, such as those influenced by differences in heat loads between waste packages, intra-layer variations in thermal properties of the surrounding fractured rock, or localized drift degradation.

Jan 1, 2004

By Lawrence S. Darken

STAFF: Editor, Gerhord Derge Cornegie Institute of Technology Schenley Pork Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: J. S. Smart, Jr., President; C. C. Long, Past-President; K. L. Fetters, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: C. L. McCabe, Chairman; H. L. Bishop, K. L. Fetters, J. J. Harwood, W. A. Krivsky, F. C. Longenberg, R. E. Lund, W. 0. Philbrook, L. L. Seigle, R. L. Smith, and F. L. Vogal. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: C. L. McCabe, Chairman; R. E. Lund, Vice-chairman; D. H. Baker, Jr., W. A. Krivsky, R. A. Lewis, Paul Qusneau, A. S. Russell, R, E. Shinkoskey, W. W. Stephens, and M. E. Wadsworth. Institute of Metals Division: L. L.Seigle, Chair-man, P. A. Back, J. J. Backer, l.l. Bessen, J. 0. Betterton, Jr., J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, R. B. Gordon, C. D. Graham, Jr., R. W. Guard, J. C. Gurland, E. L. Harmon, J. J. Hager, A. A. Hendrickson, M. Harmon, J. N. Hobstatter, H. H. Johnson, Jr., H. 5. Kolish, R. R. Nash, T. N. Rhodin, R. H. Richman, W. Rostokar, P. G. Shawmon, C. W. Spencer, L. Slifkin, J. K. Stanley, C. D. Starr, R. Steinitz, and H. C. Stumpf. Iron and Steel Division: H. L. Bishop, Chairman; 2. E. Boni, F. C. Langenberg, J. B. Wagstaff, and T. V. Wainwright. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription PetroleumEngineers,$30 per year for non-AIME members in United States and North, South, and Central America; 332, foreign; $5 for AlME members. Single copies, $4.00, single copies foreign, $5.00. The AlME is not responsible for any statement mode or opinion expressed in its publications . . . Copyright 1%1 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address; AIME New York ..Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts.. .Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 221, Number 4.

Jan 1, 1962

By E. R. Maize

This report is the second of a series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company's Crucible mine, operating in the Pittsburgh bed in Greene County, Pa. This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939

By L. Andrews

Keywords: mineralogy, phase-chemical, chemical-looping combustion, XRD, SEM, EDS, QEMSCAN, PGM, slag, matte, ilmenite Mineralogy, traditionally associated with concentrator studies, is being increasingly applied to problems in pyrometallurgy. Such investigations commonly make use of a number of techniques, and the results are combined for a meaningful interpretation, which can lead to a successful solution. Mineralogical applications are described from pyrometallurgical operations. Examples are given of studies and investigations involving mineralogy in chemical-looping combustion, feed monitoring to platinum-smelting furnaces, and losses to slag in base metal and platinum smelting.

Jan 1, 2011

By Jhony Mamani

El presente texto describe los casos de recuperación de recursos en rampas y taludes finales de un tajo abierto. El primer caso está referido a la recuperación de mineral en la rampa principal del tajo Chaquicocha, y el segundo, la recuperación de mineral en taludes de los tajos El Tapado y La Quinua.

Jan 1, 2017

Some 800 analyses for Cu, Zn, Pb, Ag, Fe, S, CaO, MgO, C02, Si02 and Al203 were used to examine the elemental constitution of the Mount Isa ores, and, for comparison, those of the Northern Leases area.Lead: zinc relations show little order from sample to sample, but means of large zones (Le. individual orebodies) show a highly linear inverse relationship. Lead: silver ratios are fairly constant from sample to sample, and means show a highly linear direct relationship.Sulphide sulphur appears to be related to carbonate and alumina abundance, sulphur decreasing systematically with increase in the ratio CO2:AI203. In all graphs involving members of the group CO2-A203-S the lead-zinc and copper ores conform to the same simple trends, confirming that the two ore types and their host rocks are genetically closely related. The earlier deduction of a volcanic-sedimentary origin for the sulphides of the Black Star orebodies appears compatible with present findings.On the basis of such an origin, the pattern of sulphide occurrence and mineralogy in the Mount Isa district is possibly related to the configuration f the upper surface of the "Eastern Creek Volcanics", the facies patterns of the overlying sedimentary rocks, and to the oldest faults affecting the two.INTRODUCTIONStanton (1962) described and interpreted the chemical constitution of the Black Star No. 2 lead-zinc and the 650750 copper orebodies at Mount Isa. The investigation has now been extended to the other principal orebodies of the area.The earlier study showed that the host rocks of the two adjacent Black Star orebodies were constitutionally closely related, and suggested that this was probably due to their original formation in contiguous zones of sedimentation. On this basis the silica-dolomite of the copper ore appeared to represent the slightly more shoreward, "limey" member, probably a fairly massive algal calcareous sediment laid...

Jan 1, 1963

A pilot plant was constructed for the low temperature carbonization of Wallarah (N.S.W.) coal at the rate of 300 lb/hr. The design was based on an entrained state carbonizer developed by Parry and D.S. Bureau of Mines co-workers. Prior to delivery to the client, the plant was successfully operated over periods of several days duration.INTRODUCTIONIn September 1961, the Australian Mineral Development Laboratories (A.M.D.L.) was engaged by the Broken Hill Pty. Co. Ltd. (B.H.P.) to design, construct and test an entrained state coal carbonizer with a capacity of 300 lb/hr of Wallarah (N.S.W.) coal. Char product was required within the specification 15·5 -I- 1 per cent volatile matter. The design was to be based on a pilot plant developed by Parry and others in the D.S. Bureau of Mines Coal Research Laboratory at Denver, D.S.A. The method involved the carbonization of fine coal by entrainment with air in an externally heated reactor. The heat required for the carbonization of the coal was to be supplied to the bed both through the reactor walls, and also by internal combustion of products in the bed. Several D.S. Bureau of Mines Reports of Investigations weFe used as the main guide to the physical layout and proportions of the plant. However, the individual units required detailed designing, before engineering drawings could be prepared and fabrication begun.A 10 ton sample of crushed Wallarah coal was used for preliminary testing of the plant. The first test run on the pilot plant was carried out in February, 1962. After some modification a second test of longer duration was conducted in August, 1962. These operations aimed at running in the plant and also at determining the operating temperature to produce specification char and the maximum capacity of the...

Jan 1, 1963

By Denis Thibodeau

The selected mining method for the Rodeo lower Zone is slot and slash. Initial design indicated that the stope height should be limited to a maximum of 18 m, thus six levels were needed to extract the ore. Higher stope height in the Rodeo Lower Zone means less development thus less capital required to extract the available reserves. It was proposed to eliminate one level by establishing 30 m and 24 m level intervals. To ensure that no stability problems will be encountered by eliminating one level, a Matthew analysis, based on diamond drill core information, was performed for the Lower Rodeo Ore Body. In addition, comparisons between the rock mass quality of Meikle Main Zone below 1825 L and Meikle East Zone between 1600 L and 1750 L with the rock mass quality of the Lower Rodeo were made

May 1, 2002

By E. R. Maize

This report is t e second of s series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company?s Crucible mine, operating in the Pittsburgh bed in Greene County, Pa, This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939

By D. Lusinga

Hydrocyclones are a common feature in almost all mining operations in the world, serving mainly as classifiers. Some of their advantages include low capital costs, low space requirements and their ability to reduce residence time in closed circuit grinding processes. Although an extensive body of literature exists for hydrocyclones, these devices are still inherently inefficient, and more research is currently being undertaken, particularly in the field of modelling. In the vast body of hydrocyclone literature published so far, there has been little or no effort devoted to analysing the effect of the cone force ratio on the performance of hydrocyclones. The cone force ratio is defined as the ratio of the spigot to the vortex finder diameter (Shah, 2005). In this study a total of 44 tests was carried out in a custom-built rig at the University of Cape Town. These tests were aimed at evaluating the effect of the cone force ratio on the performance of as mall diameter hydrocyclone. The cut size and water split were used as the criterion for evaluating the performance of the hydrocyclone. Results from the tests showed that the cut size decreased with an increase in the cone force ratio. The cut size also appeared to decrease as the calculated locus of zero vertical velocity (LZVV) shifted inwards. The water recovery to the underflow appeared to increase with an increase in the cone force ratio. The effect on the cut size of adjusting the cone force ratio was found to be higher for a coarser feed than it was for a finer feed.

Jan 1, 2009

About MAC ? The national organization of the Canadian mining industry ? Mining, smelting and refining of base and precious metals ? Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ? Many associate members ? www.mining.ca

Aug 1, 2013

By John D. Rockaway

Failure of the mine floor supporting coal pillars frequently occurs when the subcoal strata include "underclays" or other low strength strata. The failure process has been studied to define the response of these materials to applied coal pillar loads and to determine the applicability of bearing capacity analysis to evaluate unsafe conditions. The study has been accomplished through an investigation of both the intact and insitu geotechnical properties of the subcoal strata and through the installation of floor movement monitoring instrumentation. The results of these studies have indicated that both the shear strength of the underclay and the stratigraphy of the subcoal strata must be considered in the analysis. The shear strength was the major controlling factor determining the ultimate load carrying ability of the materials, but the thickness and stratigraphic position of the weak layers influenced the mechanism of the failure process. The methods of bearing capacity analysis were used to define pillar stability that included provisions for taking into consideration a two-layer system. Conditions assumed for a coal mine where a weak underclay overlies firmer strata. The results of the analysis compared very well with observed mine conditions, indicating marginal conditions in areas of the mine which later experienced pillar support failure. In addition, a "heave factor" was derived to predict potentially unstable floor conditions in the mines studied in detail.

Jan 1, 1979

By Michael Alber

Coal mining by the longwall method typically causes seismic events. This paper describes the research on mining induced seismicity around two specific longwalls at 1100m depth under several old longwalls. A local network featuring 21 geophones has been installed, underground core drilling and an extensive rock testing program were executed. A rock mechanical model featuring a multi-layer strata was created for use with numerical analyses. Seismic events were localized and three different event types are described. Focal analyses yielded distinct modes of failure. Those types are explained by different failure mechanisms, namely fault activation, remnant pillar punching and beam failure. The use of rock mass classification, rock mass strength criteria and in situ stresses together with 2D and 3D numerical analyses allows evaluating the findings from seismology approaches. Conclusions are drawn that the orientation of longwall with respect to the major horizontal stress orientation plays an important role in mine induced seismicity.

Jan 1, 2008

Exploring the Breakage Environment in Mills with Discrete Element Methods

Sep 13, 2010

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

By Albert W. Deurbrouck

The percentage of coal cleaned mechanically has increased greatly in the past 30 years. This technological change in preparation methods, accompanied by mechanical innovations in most phases of coal mining, has enabled the industry to supply quality coals at competitive prices. The Bureau of Mines has contributed to this progress by conducting research on coal-preparation problems, by evaluating the performance of domestic-and foreign-made preparation equipment, and by recording advances as they occur in industrial coal-cleaning practices. The Bureau's work in this field is recorded in the more than 150 technical and scientific publications listed in this volume. These reports, published by the Bureau over the past half century, document the Nation's progress in a vitally important phase of fuel technology.

Jan 1, 1961

By K. J. Fair, H. W. Smith, D. R. Francis, J. M. Toguri

"Bench-scale batch milling and screening tests were carried out on secondary aluminum dross 10 produce an aluminum concentrate. To complement these tests, an analysis of a commercial plant was also performed by sampling dross at various stages in the plant's milling and screening circuit. These studies have indicated that benefits of increased capacity, grade and recovery of aluminum metal can be realized by addition of screens before the ball mill, longer grinding period and by grinding the smaller size fractions more efficiently.To test the predictions, a plant test was performed on the milling of100tons of secondary dross. The recycling of the large size fraction (+1/8 in.) of aluminum dross through the impact mill rather than through the rate limiting ball mill resulted in a comparable aluminum grade. The ball milling of the _1/ 8 in. + 10 mesh size gave a dross grade of71% AI. A lower feed rate to the ball mill resulted in a higher final grade. With minor modifications, secondary dross can be processed in 22% of the time it takes with the present circuit without a sacrifice in grade.IntroductionSecondary aluminum dross is a mixture of metallic aluminum, aluminum oxides and salts (alkali halides). Any comminution process deforms or slowly grind s the malleable metal phase and reduces the size of the friable, brittle, oxide-salt phase relatively fasterr(1).The milling of aluminum dross is performed to upgrade the metallic aluminum fraction. Figure I shows a flowsheet for the milling of secondary dross as presently practised at Metals and Alloys Co. Ltd., Toronto, Ontario. At point A, large acceptable grade material is hand picked for refurnacing, the unacceptable off-grade material is sent to the sweat furnace and the remaining, + 2 in. fraction is recycled through the 3.9 ft by 4.1 ft impact mill. For simplification, three ball mills are shown. However, in reality there is only one, a 5 ft by 10 ft ball mill used in a semi-batch mode. The 2 in. + 3/8in. and 3/8 in. + 10 mesh products are remilled in the ball mill. The -10 mesh material is discarded as waste."

Jan 1, 1987

The ore is very 'refractory. It consists essentially of arsenical pyrites, iron pyrites, zinc blende, galena, antimony as sulphide and probably, in combination with galena, as Jamesonite, magnesium, and aluminium silicates with quartz. Some of the oxidized ore, of which there is very little, has a very interesting composition. A specimen shown to me by the ,general.manager, Mr. F. B. Stephens, consisted of hydrated arseniate of iron, orpiment, pyromorphite, lead oxide, with magnesium silicates and quartz. The ore found in the mine with a composition similar to this specimen was valued for gold contents at 60 oz. per ton. This ore is found as a small leader, which runs parallel to the main ore body, at intervals cutting through it.The ore is conveyed from the mine to the reduction works by means of a double road tram line. The mine is situated about rooo feet above the plant on a hill. The grade is so great (about I in 2) that the loaded trucks coming down are able to pullthe empty ones up, thus obviating the necessity of motive power for haulage. All that is necessary is two large grooved pulleys, fixed at the summit of the hilI, and provided with a rope-break for steadying the speed of the trucks down the hilI.

Jan 1, 1903