Search Documents

By Yuanbo Zhang, Mingjun Rao, Guanghui Li, Chongzhong Ouyang, Shuhui Zhang

Oolitic hematite ore with high-phosphorus content is currently recognized as one of the most refractory iron ore resources in the world. The high-phosphorus content and unique structure of the oolitic hematite ore make it difficult to be beneficiated. The process of direct reduction followed by magnetic separation has significance to the utilization of oolitic hematite ore, and sodium salts can improve the dephosphorization. However, the behavior of phosphorus during reduction roasting, and the intensified dephosphorization mechanism of sodium salts are not clear. In this study, by using chemical analysis, chemical phase analysis, XRD analysis, optical microscopy, and scanning electron microscopy analyses, the behavior of phosphorus during reduction roasting of high-phosphorus content oolitic hematite ore and the effect of sodium salts on behavior of phosphorus were studied.

Jan 1, 2015

By J. J. Kim

In a study of buildup in a green-feed reverberatory furnace, it was determined that approximately half of the crucible area has a moderate buildup of 25 in. or less, and that the area extending 45 f t from the burner end of the furnace has only a slight buildup. The false bottom, averaging 6 in. in thickness, was found to cover the entire crucible area. The stratification of Cr2O3, A12O3, and SiO2 occurs throughout the slag layer; this phenomenon is the principal reason for the formation of the false bottom in the green-feed reverberatory furnace. The false bottom is caused primarily by the settling of FeO*(A1,Cr),03 aggregates, which are derived mainly from returned converter slag. The false bottom can be transformed to a solid permanent buildup in the furnace, particularly when the matte is completely withdrawn. From the material balance of Al2O3 and Cr2O3 around the furnace, It is estimated that the average rate of aluminum chromite accumulation is approximately 0.3 ton per day or less.

Jan 1, 1976

By Kimio Itagaki

The distribution behaviours of the VA elements between the gas, slag and matte phases in copper smelting were evaluated on the basis of the thermodynamic data, most of which were determined by the authors. The distribution is basically dependent on the process factors such as temperature, the content of the element in charge, the amount of the waste gas and degree of vapour saturation with the elements. The thermodynamic quantities such as the activity coefficients of the VA elements in matte, the activities of iron and copper, SO2 or 02 potential and the distribution ratio of the elements between the slag and matte phases seriously affect the distribution, and the behaviours in various smelters could be explained systematically and reasonably by considering the changes in these quantities, In oxidation smelting at PSO2= 0.1 to 1 atm, the proportion of arsenic and bismuth in gas is predomi22t for the arsenic and bismuth distributions in both smelting and converting stages. The degree of vapour saturation has serious effect on the distribution, and sufficient contact between gas and matte phases is desirable for transferring arsenic and bismuth into gas phase.The elimination of antimony by means of vaporization is not significant. In reduction smelting at po2 = 10-11 atm, the proportions of arsenic and antimony in the gas phase are quite small, but the proportion of bismuth does not change significantly.

Jan 1, 1983

By Veena Sahajwalla

The cupola furnace is a coke-fueled shaft furnace used as a primary melting unit in iron foundries. Control of chemical composition of the iron tapped from the cupola is a key factor in productivity and quality control. In an effort to develop a control model for the cupola, a fundamental approach based on physical and chemical principles has been taken to describe the melting process. The behavior of oxidation of the solid charge in the stack of the cupola has been studied. Sulfidation of the charge materials by sulfur-bearing components released to the furnace gases from the coke has been described. Carburization of metal droplets of iron and of steel in separate molten streams has been characterized. Finally, reactions with alloying elements in the hearth (well) of the furnace have been defined. These reactions have been described in a computer-implemented model developed to predict the composition of the iron tapped from the cupola. The model has utilized the thermodynamics and kinetics of the oxidation, sulfidation, and carburization reactions, including temperature and physical aspects, in the various zones of the melting unit. The model predictions have been compared favorably with operating results.

Jan 1, 1992

By Gus Van Weert

Solvent extraction of iron from zinc refinery liquors has been investigated before, mainly on the MEHPA / HC1 stripping combination. Leakage of chloride into the zinc electrolyte and the costs of handling the ferric chloride eluate have prevented this option from being adopted. This work explores the stripping of the ferric loaded organic phase with nitric acid to take advantage of the possibility of regenerating up to 6N nitric acid, and clean spheroidal hematite production by autoclave treatment of ferric nitrate solution. The work was carried out with DEHPA (di 2-ethyl-hexyl phosphoric acid) in kerosine. Degradation testing proved the DEHPA to be very stable, when exposed to nitric acid solutions up to 6N and temperatures up to 70" C over a period of five days. Ferric iron was removed completely froma synthetic hot acid leach liquor, irrespective of the DEHPA concentration. Stripping the ferric turned out to be the problematic step. Although the stripping efficiency was considerable better at 50 than at 20° C, it decreased with increasing DEHPA/Fe ration in the organic phase. Eluates of no more than 5-10 g/l ferric nitrate were produced. surprisingly, nitric acid was found to be a less efficient stripping agent than sulphuric at equivalent normality and its efficacy levelled off above 4N. It was concluded that DEHPA does not appear to be the S.X. reagent to take advantage of the low cost autoclave decomposition of ferric nitrate opportunity in zinc hydrometallurgy and that another S.X. reagent, also resistant to nitric acid, but based on weaker compound formation is needed.

Jan 1, 1998

By Xu-ling Chen, Qian Li, Yong-bin Yang, Zhao Jing, Tao Jiang, Guang-hui Li

"It is generally known that alkali metals are harmful to blast furnace production resulting in aggravating RDI of sinters, abnormal expansion of pellets, deteriorating blast furnace lining, etc. Sinters regarded as dominating burden of blast furnace are determined as the main source of alkali metals. In this study, the removal behavior of potassium and sodium oxides by pre-reduction sintering during the sintering process was studied. The removal ratio ofK20 and Na20 was greatly influenced by coke powder content, carbon species, coke powder adding ways, additive and so on. Under the conditions of carbon rate 12% and 5% dosage of CO supplied in the sintering process, the corresponding removal ratio ofK20, Na20 was 69.00% and 32.79%, and metallization ratio could reach 4.65%. This technology provided a novel process for reducing the content of alkali metals in sinters and dramatically improving the quality of blast furnace burden.IntroductionSinter is the main iron-bearing charge of blast furnace for iron-making in China, making up about 80% of the total burden; therefore, its quality has a significant influence on the quality of pig iron and blast furnace operation. Research and practice of numerous years prove that potassium and sodium coming from ores are brought into blast furnace and upgraded, which is one of the essential reasons that lead to blast furnace nodulation and influences its strength. Currently, effective flow sheet to remove potassium and sodium is weak magnetic separation-intensive magnetic separation-flotation [l], while iron ore concentrate is still ofhigh levels of potassium and sodium. As sintering process is also not effective to remove potassium and sodium, blast furnace in China is of high alkali burden, e.g. it reaches 5.6-6.2kg/tFe in Baotou iron making plant, which is greater than international tolerated level of2.55kgltFe [l]."

Jan 1, 2013

By Jilai Xue, Jun Zhu, Baisong Li

"TiB2-C/C Function Gradient Materials (FGM) is used in cathode materials to improve aluminum wettability and melt penetration in aluminum electrolysis. In this investigation, FGM was tested for use as part of the cathode materials, where a 10 mm thick TiB2-rich layer was on the top as an Al-wettable surface, the TiB2-C layers in the middle as a gradient layer and the carbon on the bottom as a base. Electrical resistances ofFGM were determined in the temperature range of25- 9600C in argon atmosphere. The results show that the present of TiB2-C gradient layer can reduce the open porosity and the electrical resistance of the cathodes materials at elevated temperatures. The cathode samples after aluminum electrolysis usually demonstrates an increase in electrical resistance, but the application of FGM layer can compensate such an increase for certain extend due to less variation in porosity and lower the level of melts penetration.IntroductionCarbon is still used for aluminum reduction cathodes dominantly, but it has a poor wetting properties by liquid aluminum and the anode-cathode distance has to be kept about 4-5cm with an additional 1.3-2.0 V voltage drop [l]. TiB2 has better wettability by liquid aluminum with higher electrical conductivity and stronger chemical resistance to the electrolyte attack. And the wettability ofTiB2-C composites cathode on liquid aluminum can be also improved, while liquid aluminum can completely wet the cathode surface ifTiB2 content exceeds 27% [2-4]. However, during the process of TiB2-C composites cathodes preparation and aluminum electrolysis, the deformation by temperature variation or sodium penetration are great disparity between TiB2 and carbon due to their physical properties difference. This will accelerate the cathodes cracking and deterioration."

Jan 1, 2013

By V. M. Paretsky

The basic work conducted by Prof. A.Yazawa has demonstrated that in order to ensure single-stage white metal production by autogenous smelting of copper sulfide raw materials, it is most favorable to use highly basic slags, in particular oxide systems CaO-FeO-Fe2O3-Sio2. he special studies have been conducted in the Gintsvetmet Institute to investigate the composition and structure of slags produced on a semi-commercial scale when testing the KFP and FBP processes for white metal smelting, as well as the slag obtained in a full-scale KFP furnace at the Almalyk copper smelter. The investigations conducted have demonstrated why production of high-grade matte or white metal is associated with lower loss of copper in slag in a series: silicate slag I silicate-calcium slag I ferrite-calcium slag.

Jan 1, 2003

By Minjun Tang, Jianfeng Zhou, Feng Chen, Linjiang Qing, Xiaolei Song, Yufeng Guo, Tao Jiang

"Reduction swellability index (Rsn and low temperature reduction disintegration index (RDI) of vanadium-titanium magnetite oxidized pellets are harmful to the processing of ironmaking, for example, causing serious gas permeability, decreased yield, higher coke ratio and more furnace dust. Thus, the improvements of RSI and RDI of vanadium-titanium magnetite oxidized pellets were investigated in this paper, including the pretreatment of raw material, additives of dolomite or boric acid, pellets treated in chloride solution and so on. The results showed that damp milling as pretreatment and boric acid added in pelletizing were conducive to the RSI which decreased 5% and 7% respectively, while they were not efficient enough in improving RDI. Dolomite was efficient in improving RSI, but had negative effect on RDI. There was no evidence to show that RSI and RDI would be improved when pellets were treated in chloride solution. Pursuing this further, the mechanism of those improvements were investigated.IntroductionIn the world, vanadium-titanium magnetite utilization is investigated around how to recover iron, titanium, vanadium, and divided into blast-furnace method and non-blast-furnace method according to respective characteristics. Blast furnace method [1, 2] can recover iron and vanadium effectively, but Ti02 cannot be recycled. Non-blast-furnace methods include rotary kiln-electric furnace method, pre-reduction electric furnace method, reduction- grinding method and sodium vanadium-rotary kiln-electric furnace method and so on. [3-7]Comparing to the Non-blast-furnace method, the method of blast furnace smelting has been put into industrial applications. And it has the following advantages: First of all, effective recycling iron and vanadium; Second, technical problems of high titanium slag in blast furnace smelting; Third, it has mature technology in blast furnace smelting."

Jan 1, 2013

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

Inexpensive and high-quality sinter has an extraordinary position in iron making, and there are many factors influencing the sintering. This research takes the basicity and coal dosage as research subjects to do the experiments based on cost analysis with sinter pot experiment system. Linear program is taken to make the schemes of ore blending. During the experiments of changing basicity from 1.6 to 2.3, the properties and microstructures of the sinter are studied. It comes to a conclusion that increasing the basicity is beneficial to sinter quality but leads to higher cost. To further ascertain the cost of sinter and the potential of saving coke, the work of improving coal dosage is taken on the basis of experiments of changing basicity. Through analyzing the results, a formula (Y=1849+261.1R-130.6C) is proposed which indicates the relation among the cost, basicity and fixed carbon content. And it works well for actual production.

Jan 1, 2015

By Wei Yu, Tiejun Chun, Jian Pan, Deqing Zhu

In this paper, improving the pelletization of Brazilian hematite by adding a boron bearing additive was carried out, and the pelletization parameters were also optimized. The mechanism of boron bearing additive was revealed in the kinetics of crystal grain growth by using LEICA microscopy and its software to measure hematite grain growth. Good qualities of green balls are manufactured with drop numbers above 5.7 times/0.5m, compressive strength higher than 13 N/pellet and thermal shock temperature over 620? under the following conditions: 1.2wt% bentonite, 0.4wt% boron bearing additive, 7wt% moisture and pelletizing in disc for 15 min. When the green balls were preheated at 1000? for 8 min and fired at 1280? for 15 min, the compressive strength of the fired pellets containing boron bearing additive is about 3096 N/pellet, which is far beyond the standard requirement for good quality pellets. Compared to the fired pellets without adding any boron bearing additives, the compressive strength of fired pellets containing boron bearing additive is increased by 1225 N/pellet. It is revealed that adding boron additive into the hematite pellets help to form more liquid phases, lower the activation energy of the hematite grain growth by 135.2 kJ/mol and increase grain growth rate by 33.6%, leading to higher strength of fired pellets due to forming more coarse and dense recrystallized hematite and energy saving by firing at lower temperatures for shorten time.

Jan 1, 2011

By Lin Li, Wen Shi, Hua Wang

"Specimens of the ultra-low carbon bake hardening steel were soaked for 1 min to 5 min, and then cooled by water quenching. The internal friction experiments were carried out to detect the spectra of the specimens. Results show that Snoek peaks are present in all the specimens, however, an obvious Snoek-Koster peak is found only in the 5 min-annealed specimen. Besides, tensile results indicate that the bake hardening values increase with the annealing time prolonging from 1 min to 3 min, but decrease as the annealing time prolongs further to 5 min. The solute distributions in the specimens were characterized by three dimensional atom probe. Some segregated C and V are found in the 1 min-annealed specimen, and the C and V contents decrease as annealing time prolongs to 5 min.1. IntroductionAs an excellent member of automotive body panel materials, various types of bake hardening (BH) steels have been developed since 1980s. Bake hardening property, as one of the most important mechanical properties, has been studied by many researchers [ 1-5]. As is known, BH phenomenon is generally controlled by the interaction between solute C and dislocations. The Snoek peak of internal friction (IF) is very popular in the investigation of solute C [6-9]. However, result of internal friction cannot suggest the distribution pattern of solute C as well as its influence on BH phenomenon.Three dimensional atom probe (3DAP) can diagnose solute element atoms as well as nano-sized precipitates, and it is the only instrument that currently can identify the identities of individual atoms in a material and measure their spatial coordinates with the resolution close to 0.3 nm [10]. There have been a number of studies about using 3DAP to detect solute elements as well as nanometer sized precipitates [11-19]. For example, Hono et al. [16] used 3DAP to determine the solute elements in an age-hardened Mg-Ca-Zn alloy, and they also obtained the distribution patterns of the observed elements."

Jan 1, 2011

By Antoine Allanore, Luis A. Ortiz, Donald R. Sadoway

"The steelmaking industry has drastically reduced its energy consumption in the last fifty years, and today’s technologies are considered to operate at their optimal efficiency with respect to energy needs. To cope with new constraints related to greenhouse gas (GHG) emissions, a change of paradigm is necessary. One of the promising technologies that could be deployed to help reach CO2 mitigation targets relies on the intensive use of electricity: molten oxide electrolysis (MOE). This paper presents the key process parameters that need to be tuned to address the practical needs for both high productivity in a steelmaking reactor and for an energy efficient process. Herein we show that contrary to common perception, the electrolysis process for ironmaking requires less energy than today’s chemical reduction route. Furthermore, we prove that most of the energy that must be provided to operate the electrolytic iron production cell is thermal energy which is readily generated by joule heating during electrolysis due to large currents being passed through the electrolyte. The energy consumption of the electrolysis cell is therefore shown to be highly dependent on the cell configuration and the chemistry of the electrolyte. As a consequence, the CO2-impact of the technology strongly depends on both the power production mode and the technological choices for design of the process, including cell configuration. Surprisingly enough, even when the electricity generation is not carbon-free, MOE still appears to be viable from the perspective of reducing GHG emissions providing sound reactor design considerations are made.IntroductionIn the context of greenhouse gas (GHG) emissions mitigation, the steelmaking industry is considering several techniques that could sustain the efforts and progress achieved by this sector in the last decades [1]. A recent report [2] on potential routes for low-CO2 steelmaking highlighted for all techniques both the strong dependency of CO2 emissions on electric power production mode and the need for a decrease in energy consumption per tonne of steel. Incited to innovate with respect to this last criterion, the steel industry considers electrolysis to be a promising technological solution, and in particular the molten oxide electrolysis (MOE) process. This process conducts electrolysis in a mixture of oxides that dissolve the iron oxide feed, which by the action of electric current is decomposed into liquid iron and oxygen gas. The opportunity for reduction in energy consumption during steelmaking by MOE is commonly attributed to the “direct” pathway from iron oxide to liquid metal offered by the use of a molten oxide melt and operation at a temperature above the melting point of iron, ideally 1600°C, to provide enough superheat for tapping the molten iron product:"

Jan 1, 2011

By Vinicius Alves Gomes, Jean Igor Margem, Frederico Muylaert Margem, Sergio Neves Monteiro, Marina Rangel Margem

The interface between the matrix and the reinforcing fiber plays an important role in the efficiency by which an applied load is transmitted through the composite structure. The shear stress at the fiber/matrix interface can be associated with this load transference and, consequently, affects the composite strength. In the present work, pullout tests were used to evaluate the interfacial shear stress of malva fiber in epoxy matrix composites. A small critical length was found for the malva fiber embedded in epoxy, which corresponds to a relatively weak fiber/matrix bond and lower interfacial strength.

Jan 1, 2015

By Wen Chen, Xinghua Liu, Zeyou Peng, Qiulin Wang

"Limonite is a collective for iron hydroxide argillaceous materials. It is very difficult to be treated due to the wide variation in specific gravity and magnetism and the high argillization rate in the course of grinding and beneficiation. The iron ore in Huangmei, Hubei, China is the typical representative of limonite. If the limonite is processed using conventional physical beneficiation methods (e.g. magnetic separation, gravity separation, flocculation-desliming-flotation, or a combined process of the three), it can only be obtained an iron concentrate grade of 51.98% and an iron metal recovery of 86.64%. However, the technique of flash magnetic roasting-magnetic separation can improve the concentrate grade to 61.03%, iron recovery to 91.17%. This paper describes the tests of recovering limonite by flash magnetic roasting in detail.IntroductionLimonite (mFe2O3, nH2O)[1] is a general designation for hydrous iron hydroxides and argillaceous matters. Limonite is hard to be separated because of its complicated geneses, comparatively weak magnetism, nonuniform grain size and being easily slimed during grinding. So most small and medium enterprises sell deslimed limonite product which was dealt with just by simple methods of washing, magnetic separation or gravity separation and so on. In recent years with the iron ore prices soaring, significant progress was made in mineral processing research of limonite. Laboratory research and industrial test results showed that flocculation-desliming-flotation process and roasting-magnetic separation process are the two best methods to recover limonite till now. To compare these two methods, roasting-magnetic separation process is superior to flocculation-desliming-flotation process in aspects of beneficiation indexes and industrial stability."

Jan 1, 2012

By C. S. Ek

As a continuation of previous work, further tests have been carried out to recover silver from the residues obtained in a zinc jarosite process. Selective flotation has been performed with different reagents, and ?cleaning steps have been introduced to upgrade the silver concentrate. Leaching of crude residues, as well as flotation tailings, has been carried out with cyanide and thiourea. Finally, the different beneficiation methods are compared, and the industrial aspects? of their application are reviewed.

Jan 1, 1990

By Zhucheng Huang, Yuanbo Zhang, Kecheng Zhang, Guanghui Li, Tao Jiang

"With rapid development of Iron and Steel industry, plenty of metallurgical dusts and sludges are generated, which have not been effectively utilized because of their poor hydrophilicity and bad ballability. Agglomeration and roasting of metallurgical dusts & sludges with a new-type composite binder are studied in this paper. The results indicate that the dosage of the new binders can be decreased to 2.5 wt% from 3.5 wt% when using the wet-grinding process. Under the optimal conditions of briquetting pressure 2070 N/cm2, briquetting moisture content 13 wt%, roasting temperature 1000 °C and roasting time 40 min, the qualities of the green, dry and roasted briquettes meet the requirements of the industry production. The finished products have the compression strength of more than 2000 N/cm2, which can be used as high-quality burdens for blast furnaces.IntroductionWith rapid development of Chinese Iron & Steel industry, there are more and more serious resource shortage and environmental pollution existing. Converter sludges, containing 30% ~ 40 wt% moistures, are typically difficult for recycling [1]. Foreign processing technologies for sludges treatment are relatively advanced including cold-bonded agglomerates for blast furnace, RHF reduction for the dusts and sludges with high content of Zn and Pb, smelting and reduction. Domestic iron and steel companies use a small amount of sludges in sintering. However, the sludges have the characteristics of high moisture and containing harmful impurities, which directly affect the sintering mixture permeability and product quality [2-5]. There are also other technologies such as production of metallized pellets, cooling agents for steelmaking, etc [6]. All of these deficiencies and applied are not in large-scale."

Jan 1, 2011

By Zhucheng Huang, Ronghai ZHONG, Tao Jiang, Jun ZOU

The method of reduction roasting and magnetic separation of low-grade, micro- fine disseminated refractory iron ore following granulation with coal produced unexpected success. Pellets of iron ore with diameter between 3 and 8mm were granulated with coal, bentonite and water. The raw pellets and reduction products were analyzed by scanning electron microscopy and x-ray diffraction. Results show uniformly distributed coal powders inside the pellets improved the kinetics of the reduction process and accelerated the reduction rate. Reduction time was higher at temperatures below 890℃, which resulted in the formation of substantial amounts of fayalite. When temperature was increased, micro- fine hematite was then quickly reduced to iron metal and the amount of fayalite decreased sharply. When pellets were reduced at 950℃ for 25min, reduction products with 56.73% metallization rate were obtained. After grinding and magnetic separation, a concentrate with 72.18% Fetot was obtained.

Jan 1, 2015

By Hong Ouyang

A unified computational model has been developed for the Bridgman growth processes of B-NiAI and CdTe crystals. To handle the geometrical and physical complexities, a two-level approach has been developed. At the gtobatlevel, conjugate heat transfer, phase change dynamics, and variable material properties along with the realistic geometries and thermal boundary conditions are accounted for inside the entire crystal growth system. Refined calculations are then made within the ampoule, with the boundary conditions supplied by the global simulations. This model can optimize the use of computational source, help understand solidification behaviors, and improve designs of crystal growth system.

Jan 1, 1996

By Shigeatsu Nakazawa

Activities of Bi and In in the Bi-In liquid alloy were measured over the whole range of composition at the temperatures from 850K to 1050K. An alloy was vacuum-sealed in a quartz cell and heated at the temperature of interest. The absorption for 307nm radiation from Bi lamp was measured for Bi atom vapor in the cell. By heating a pure metal as a standard and measuring the absorbance as a function of the temperature, an analytical curve for Bi atom vapor was constructed and used for conversion of the absorbance to the vapor density. Bi activity was determined as the ratio of the Bi atom vapor density over the alloy to that over a pure metal. The same procedure was applied to the In 304nm radiation from In lamp and In activity was determined independently of Bi. Results showed that the liquid Bi-In system behaves like a regular solution.

Jan 1, 2003