Search Documents

By M. Karmis

The determination of the surface area which may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted Furthermore, the influence of both mining and geological factors, such as mining width and depth and overburden lithology, on this angle is examined, using the Surface Deformation Prediction System (S.D.P.S) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1994

By N. Kuyucak

While Acid Rock Drainage (ARD) occurs naturally, its management poses challenges especially at the decommissioned sites. Two passive systems were designed and implemented at two different decommissioned mining sites in Canada in order to treat the seepage with ARD characteristics. One seep originating from a reclaimed tailings pond was neutral mine drainage (NMD) containing circumneutral pH and dissolved metals (e.g., nickel, zinc) in elevated concentrations. The other ARD from a tailings stack showed net acid drainage characteristics with low pH and higher metal concentrations than regulated limits. Due to the different ARD characteristics occurring at each site, different types of treatment systems were designed and implemented. Both sites experience extreme winter conditions. The NMD has been treated mainly by limestone drain and aerobic systems since 1997. The acid ARD has been treated by a system consisting of an anaerobic sulfate reducing bacteria (SRB) cell, an aerobic cell and a limestone filter since 2004. As this site has no access roads, space, or power, a significant capital cost as well as sludge disposal/storage requirements would have been required to institute a chemical (active) treatment system. Both systems have been successfully treating seepage and producing a water quality year round that could comply with regulated objectives.

Jan 1, 2010

By S. S. Xue

A study has been conducted to remove iron from sulfate solutions using Eichrom's Dipex® extractant, P,P?-di(2-ethylhexyl) methanediphosponic acid (H2DEH[MDP]). It is found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 10 6 Over 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 1999

By R. J. Sweigard

Deep tillage is used widely as a Means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage. A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids during deep tillage to prevent any significant recompaction from occurring. Various amendments were injected into the soil in the laboratory using a small-scale ripping and injection system. Measurements were made of selected soil properties to evaluate the feasibility of this method.

Jan 1, 1993

By E. R. Bauer

The trend in underground room-and-pillar coal mining is to employ remote-control continuous mining machines and extended cuts, 12 m (40 ft) deep or more. This system of coal extraction, adopted by over 435 mines, can create additional worker-safety hazards. To address the ground control and worker-positioning hazards, a combination of statistical analyses and numerical modeling was conducted. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the Coal Mine Roof Rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling to predict roof displacements during extended-cut mining was completed. The paper describes the results of these studies and their impact on the safety of extended-cut mining.

Jan 1, 1999

By P. H. Qi

Activated carbon loaded with gold from different halide solutions has been characterized by thermal analysis techniques. The mechanism of gold uptake by carbon varies from predominately adsorption for gold iodide to predominately reduction for gold chloride. TGA and DT A measurements confirm the existence of adsorbed gold-halide species within the micropore structure of carbon. These results suggest that the ration of reduced; adsorbed gold increases for gold halides in the order Au-I > Au-Br > Au-Cl. In the case of Au-I, TA results for the loaded carbon were compared with pure compounds of 12, AuI and AuI3.

Jan 1, 1996

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By D. Williamson

In the post war years metals analysts and statisticians have generally tracked the demand for metals in line with changes in OECD industrial production (IP) growth rates because, undoubtedly, the correlation between IP growth and metal demand was reasonable. However the correlation was exaggerated. During times of expanding IP growth metal demand increased at a faster proportional rate than IP growth. This was probably due to industry restocking in anticipation of growing demand at the start of each economic cycle. Conversely, metal demand would slacken at a greater rate than would be suggested by negative IP growth as industry destocked in order to reduce costs. Nonetheless, overall, a reasonable correlation between IP growth, over the longer term, and metal demand could be painted. Yet, although this correlation has stood well since the last world war it has been based on the fact that the bulk of the world's IP growth stemmed from the industrialized countries of the western world, latterly including Japan. The so called "developing world" was of little consequence, whilst countries of the Soviet Union and Communist Bloc were deemed to be closed, self-contained entities which, for each metal, would either be net exporters or importers. These quantities would be used by analysts to calculate the overall supply/demand equation for the western world only and to deduce whether a commodity was in shortage or surplus. It is now believed that this method of projecting total world supply and demand for raw materials is outdated and takes little account of the worldwide political changes which have occurred since the collapse of communism and the revitalization of China, albeit under a notional communist government. It is no longer appropriate to assess global balances for raw materials on the basis of three economic blocs namely, western world, developing world and communist bloc. Rather, global balances need to be projected on a global basis. In this regard, since the collapse of communism and the removal of many other totalitarian regimes, capitalist forces are at work and are attempting to satisfy, with some considerable success, the expectations of the great mass of the world's poorer people. Such people, usually located in Asia, Africa and Latin America have aspired to the same standard of living as people living in western Europe, North America and Japan. Now, with free market forces at work their aspirations will start to be met. Consequently, the demand for metals and other raw materials will now rise at a much faster rate than at any other time in the world's history. Not only will the production of raw materials have to keep pace with rising IP in the developed world but will also have to keep pace with the demands associated with the rising expectations of rapidly increasing populations in the developing world, as well as from within the old communist bloc countries. This paper sets out to argue the case that metal demand could well increase at a rate faster than the world's mining companies, governments and financiers can deliver.

Jan 1, 1997

By T. S. Golosinski

Use of contractors to excavate, load and haul mined material is widespread in Australia. It is also becoming a common practice in many other countries. The paper reviews current practices in Australian contract mining. Various types of contracts are reviewed, including partnering arrangements and alliancing between the contractor and the mine owner. Applicability of various types of contracts to specific mining situations is discussed, as is their impact on overall mine performance

Jan 1, 1998

By D. A. Peterson

A research program is currently in progress at the University of British Columbia to determine the potential of composite cable bolt reinforcement in Canadian mines. Several prototypes of glass fibre cable bolts have been tested. Their evaluation consisted of lab testing at the University of British Columbia, United States Bureau of Mines (Spokane) and trial installations at Detour Lake, Winston Lake, and Myra Falls Mines. A market analysis of cable bolts within the Canadian mining industry has been completed. Fibre reinforced polymer composites have a high potential as cable bolt reinforcement in mining applications. They prove to be a viable alternative to steel cable bolting.

Jan 1, 1993

By W. D. Keller

Scan electron micrographs, SEM's, will be shown of representative refractory clays from Missouri deposits, with counterparts from other localities. The story is in the pictures, ("1000 words in each picture"), but clay types include the following. Plastic, semi-plastic, and semi-flint "fire clays" of Missouri have textures which appear to retain certain relic texture of ball clay. Flint clay is composed of tightly interlocking packets, sheaves, and books of kaolinite. Diaspore and boehmite mineral textures characterize those "clays". Surface-boulder diaspore shows very pronounced recrystallization and crystal enlargement from original, unexposed first-grade diaspore.

Jan 1, 1977

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. It is also a major exporter of minerals. Canadian open pits are highly mechanized and use state of the art equipment and support technology. During the past few years significant productivity improvements have been achieved by taking advantage of larger equipment; in pit crushing and conveying; truck dispatch systems and electronic management tools. The most recent developments in Canadian Open-pit Mining are related to hydraulic transportation and the application of Global Positioning Systems. Mine planning is computerized; environmental issues are dealt with in all phases of planning; equipment modifications are pursued with vigor to keep them functioning in the hostile Canadian North.

Jan 1, 1999

By S. Tuylu, D. Adiguzel, U. G. Akkaya, A. Bascetin

"One of the main problems for storing of the tailings is acidity occurrence due to several factors such as existence of sulfuric minerals and also the pollution in seepage waters by mobilization of metal ions, which holds great risks in terms of environmental regulations. Because of these specified reasons, tailing materials to be used in a SPD formula should have comply with some specifications. Among these properties; oxygen content, temperature, matrix suction and pH are the most important parameters. In the study, the relationships between the parameters mentioned are investigated to reveal optimum paste design layout. The lowest amount of seepage water obtained from the paste layers in the pilot cabinet was found as 2150 ml from 3rd layer. As for the maximum seepage water and the average of the all 11 layers were found as 4909 ml from 6th layer and 3273 ml respectively. The reactions occurring according to the oxidation, as seen at seepage water of second and third layers, decreased the pH of system to the under of 7 value. Additionally, when the seepage water of first layer’s EC value is 2.93 mS/cm, the EC value of second layer is increased at 3.54 mS/cm. The other parameters are evaluated with the obtained results of the tests to determine the optimum storing conditions for SPD.INTRODUCTION Conventional waste disposal methods, although widely used, pose great environmental risks. One of the most important issues is acid mine drainage (AMD). Tailings of metallic mines contain heavy metals, aggressive chemicals and hazardous materials. In the presence of oxygen and water, an oxidation reaction can occur, causing a decrease in pH of the environment, and heavy metals that are present in the environment can dissolve easily. Subsequently, heavy metals can pollute underground water basins, creating a great amount of danger for the ecology and potable water resources. Another important risk associated with conventional waste disposal methods is accidents related to the waste dam. Higher volumes of water and tailings (usually 15% solids and 85% water by weight) are sent to waste dams, making it very difficult to control the stability of the dam under conditions such as static and dynamic loads (seismic activities, vibrations caused by blasting, etc.), flooding, and seepage. In case of an accident or failure, the spread of great amounts of mud containing hazardous chemicals and heavy metals can harm the environment of the dam site significantly (Bascetin et al., 2014). In the paste technology, depending on the type of ore, tailings used in the paste mixture can contain sulphide minerals (such as pyrite and pyrrhotite). These minerals are known to be reactive with water and oxygen to produce acidity (sulphuric acid)."

Jan 1, 2015

By T. F. Dumm

With increasing interest in the physical cleaning of fine coal, there is a need for extension of the sink-float analysis procedure to finer sizes. Problems arise, however, in ensuring complete dispersion of the particles in the heavy liquids. A procedure has been developed in which surfactants are used as dispersing agents and solids concentration is minimized (using a simple formula to estimate the minimum weight needed for statistical reliability). Using centrifuges to increase separation rates and sub-sieve particle size analysis of the specific gravity fractions, a complete size-specific gravity distribution can be obtained. Analyses have been performed on coal samples as fine as -10 µm.

Jan 1, 1987

By D. A. Shock

Utilizing the technology developed for oil well stimulation by hydrofracing, a disposal system which permanently fixes the waste has been proven. Large quantities of radioactive waste can be processed by a single well system making this method an attractive method for permanent radioactive waste disposal. The system depends on locating a relatively thick formation of impermeable, but easily fracturable rock such as a shale, creating a horizontal fracture, pumping the waste into the fracture in a form which will subsequently solidify and seal the fracture from the well system. The paper presents the theoretical considerations from creating and extending horizontal fractures and how these considerations were used in designing a waste disposal system which is now operating.

Jan 1, 1964

By V. Z. Sun

One of the major concerns of ground control in a coal mine is safety against failure of one of three components (i.e. roof, pillar, or floor) of the mine entry. In order to better design and evaluate stability of the mine entry with a certain confidence, a reliability approach is introduced rather than using the conventional safety factor (SF) method only. Advantages of using the reliability approach is that it not only takes variability of both rock/coal properties and stress distribution into consideration, but also assesses the stability of each component and mine entry as a whole system. Therefore, it is anticipated that, by using this approach, the current ground control technology in coal mine will convey a better sense of confidence. The results of a case example show a significant influence on the current design concept and stability evaluation of mine entry.

Jan 1, 1997

By N. Sahin, M. Can, Z. Ekmekçi, Y. Öztürk, Ö. Biçak, I. B. Çelik, B. Kocabiyik

"In this paper, a case study from Çayeli Bakir Isletmeleri A.S. (Rize, Turkey) about the selective flotation of copper minerals from sphalerite is discussed. Çayeli Cu-Zn Sulfide Ore contains different ore types, such as yellow ore, clastic ore, bornite-clastic ore, bornite-yellow ore, and black ore. For some of these ore types, selective flotation of copper and zinc is very difficult presumably due to presence of secondary copper minerals such as bornite, chalcocite and covellite, and also surface oxidation. These factors affect Cu-Zn selectivity due to activation of sphalerite particles in the ore during the process. The main objective of this work was to improve Cu-Zn selectivity by optimization of the pulp chemistry for different ore types of Çayeli ore. After preliminary flotation tests investigating effects of different chemical conditions, a plant survey was performed to determine the plant performance and sources of the problems when problematic bornite-clastic ore is treated in the plant. Various chemical conditions are tested in the laboratory scale test for better depression of sphalerite in copper flotation circuit. Combination of Na2S+ZnSO4+MBS was found to be the most effective depressant scheme. INTRODUCTION Ore variability is one of the most important factors affecting performance of a process plant both in short and long term planning. The geometallurgical modelling becomes a common tool to determine ore variability problems and develop the most efficient solution during life of mine (1, 2). Flowsheet design and equipment selection and sizing are usually done based on the results of ore variability test works. However, in some cases ore variability may not be foreseen during the design stage and therefore the solutions should be developed based on the existing flowsheet and equipment in the plant. In this situation, ore characterisation, problem statement and diagnostic testing should be applied step by step. The problem could be due to changing feed grade, mineralogical characteristics, grindability and surface characteristics when flotation is involved. The variability in feed grade with fixed mineralogy can be handled with relatively simple modifications (i.e. adjusting throughput or equipment capacity) in the plant. Variability in ore mineralogy is the most complex and difficult problem to tackle. Because, mineralogical variations could bring variations in mineral composition, texture and liberation. These variations can potentially lead to the variations in grindability of the ore and flotation behaviour. Variations in grindability are usually managed by optimization of operational parameters in grinding circuit, as it would be costly to replace the existing equipment in the circuit (3). The variations in flotation behaviour are mainly due to variations in mineral types and distribution, texture and surface oxidation. One or all of these factors could be observed in a flotation operation. Therefore, a comprehensive investigation both in plant and lab scale should be conducted for definition of source of the problem. The testwork to solve the problem and retrieve the performance is planned and conducted depending on the source of the problem (4, 5)."

Jan 1, 2017

By Brajendra Mishra, Himanshu Tanvar

Niobium and tantalum extraction industries heavily depend on fluoride chemistry for metal oxide production. This study concentrates on developing a fluoride-free approach utilizing alkali treatment for selective dissolution of niobium and tantalum phases. The application of microwave heating in the alkali treatment of columbite significantly reduced the processing time, providing a higher reaction rate and recovery than conventional heating. A short duration of microwave exposure (6 min) elevated the sample temperature to more than 900 °C, resulting in the rapid formation of water-soluble niobium and tantalum complex. Metal recovery from the solution was attempted through direct precipitation using guanidine carbonate as the precipitating agent, resulting in a mixed oxide product with > 90% purity. On the other hand, solvent extraction was also attempted using methyltrioctylammonium chloride as an extractant, providing a niobium oxide and tantalum-rich mixed oxide with > 98% purity as the final product.

Mar 23, 2024

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By Jorge Amaya, Nelson Morales Varela, Francisco Saavedra, Gonzalo Nelis, René Gómez

Precedence constraints are broadly used in mathematical models and algorithms for mine planning to model, for example, slope angles in open pit operations or connectivity in underground mines. Unfortunately, these constraints do not capture relevant geometrical aspects for the design of the mine like minimum bottom space of pits or smoothness of the economic envelope in block caves. In this work, we present different approaches that utilize precedence constraints generating economic envelops that are more suitable for design purposes. The numerical experiences show that the proposed techniques produce high value envelops with better geometrical properties and that the methods proposed can be computed efficiently.

Jun 25, 2023