Search Documents

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By J. H. Bassarear

Conventional crushing and grinding circuits are compared to semiautogenous circuits. Recent installations of each circuit are reviewed and seven methods of using autogenous or semi- autogenous techniques are described. Steel and power consmption data are reported and benefits of a dedicated digital computer are discussed.

Jan 1, 1981

By P. G. Vikre

Several factors have caused less emphasis to be placed on geologic mapping in mineral exploration in the last 15 years. These include opportunities for "easy" discoveries of near surface gold and silver deposits in developed countries, and of base metal deposits as well in less developed countries, a decline of emphasis on geologic mapping in many universities, and a decline of useful mapping by government agencies in many areas. Geologic mapping is simply a way of recording geologic observations on volumes of rock larger than can be seen from one place. Since most geologic processes involve systems larger than this, mapping is also essential to understand the significance of observations made on smaller volumes of rock, such as thin sections and sample taken for chemical or isotopic analysis. To be useful, the observations recorded through geologic mapping are then interpreted to arrive at an understanding of the 3D geometry and geologic history of a volume of rock, which is used to direct mineral exploration, or any number of other purposes.

Jan 1, 1995

By Donald M. Hausen

Microscopic evaluation of trace quantities of metalliferous phases in flotation products requires counting large numbers of particles. Particle counts of many thousands may be required for precision, but not obtained practically by conventional microscopic techniques. A less tedious microscopic method for evaluating trace sulfides in mill tailings was developed for the O'okiep Mining Company in South Africa. Hundreds of thousands of particles were evaluated by this method called "gross-counting." Gross-counting consists of counting microscopic fields rather than point-counting individual particles. Total counts are calculated by multiplying the average number of particles per field by the total number of fields examined over the entire mount. Total gross-counts range from about 20,000 particles for +200 to 100,000 or more for -400 mesh size material in lucite mounts. Sulfides and metallic particles in each field are identified and tallied along with field counts. Totals for each type of metallic particle are divided by the total gross-count to give volume percent which is corrected to weight percent by specific gravity factors.

Jan 1, 1969

By M. A. Anderson

After mope than fifty years Of Continuous operation, the Nevada Mines Division found itself faced with declining ore headings and metallurgical efficiencies, and rising operating costs. Although intensive process improvement programs had been initiated at various times in its history, insufficient return on investment served to defeat plans for any major changes in circuitry. The advent of practical large-volume flotation machinery, along with the success of long-range exploration drilling programs, complimented the results of an intensive program of research and development. The result of laboratory testing, pilot plant testing, and full scale plant tests was the proven indication of metallurgical improvement given increased flotation residence time and the effect of mechanical agitation in flotation.

Jan 1, 1975

By Enrico Pavese, Tim Kearney, Stefan Lemke

Watertightness is of central importance in hydraulic and underground structures but has always been associated with a risk, as demonstrated by the very high impact that water inflows have on the damage of linings and infrastructure (Howard, 1991; Sandrone and Labiouse, 2011). Concrete is vulnerable to groundwater and chemical contaminants in the soil. These can leach into the pores and cracks of the concrete and degrade its integrity, causing spalling and corroding the reinforcing steel. Moisture migrating into the building can also degrade structural elements over time and lead to mold and other hazards to occupants’ health. In this connection, the demands placed on the setup and detailed design of the seal depending on the negative influence by water on the one hand and on the other hand on the function of a construction in view to its watertightness classification. Thus, the reliable functioning of a seal is of particular significance in the case of traffic tunnels, which are not easily accessible for all subsequent repairs after the construction in seepage water and especially when located in a pressure water zone (risk–cost assessment). Requirements for the long-term efficiency and quality of underground structures have increased in recent decades. Today, the standard lifetime requirement for an underground infrastructure project is 100 to 120 years and, in some cases, even higher. This calls for high increased attention to the durability of the whole structure and of each individual element. Standards, which started as application guidelines given by the manufacturers, are available in the market since the 1980s and are constantly adapted to the current developments in various technical committees. Differentiations are made between: Manufactures application guidelines, case studies or published articles Test standards for the laboratory to guideline the testing procedures (air temperature, type of test equipment, dimensions, test speed, test duration, concentration, type of liquids, monitoring, tolerances, interpretation of results, documentation, etc.), developed by committees based on material and laboratory experts Application standards, which include test standards but also the related minimum performance requirements (values) for material, processing, and quality assurance (practical tolerances), developed by committees based on a wide range of experts (e.g., designers, construction companies, applicators, manufactures, owners, test institutes, quality engineers) and therefore also based on a wide field of experience, different views and up-dated case studies. In the following there are some examples of guidelines and published information’s, ranked according to the year of issue, which are relevant for the development of waterproofing specifications in the tunnel industry:

Jun 13, 2023

By Ben E. Adams

The Duval Corporation Sierrita copper and molybdenum mining complex is located approximately twenty-three miles south of Tucson, Arizona. The original open pit mine, Esperanza, was put into operation in 1958 and utilized one tailings dam until the Sierrita operation began in 1970, and a second pond was started. Both tailings operations continued to be operated separate and independently of each other until 1977, when the Esperanza Mill was temporarily shut down, and the Esperanza Tailings Dam was retired from service. Except for short periods of use, no new tailings were put on the surface. With the reactivation of the Esperanza Mill in 1979, the Esperanza tailings were combined with the Sierrita Mill tailings and put on the Sierrita Dam, leaving the Esperanza Dam in a retired state.

Jan 1, 1984

By Glenn E. Craig

The practical and effective pulp distributor here presented is believed to be of a completely new and innovative design. It was developed at the San Nicolas Plant of the Marcona Mining Company in Peru, where it has been thoroughly plant tested using iron ore slurries of a particularly abrasive nature. It has proven to be superior to the apparatus originally installed, or to any observed in operation elsewhere. In plant practice the capacity and efficiency of many process units such as screens, magnetic separators, and jigs are strongly affected by the loading pattern, and for better results the flow of pulp must be proportioned across the receiving lip in equal quantities per unit width. The distributors originally installed on the drum magnetic separators in San Nicolas proved to be unsatisfactory, and several trial modifications failed to show any improvement. As is usually the case, feed rates were being steadily increased, and appreciable losses to tailings resulted. A check of the distributors on the market discloses no reasonable substitute, so efforts were directed toward devising an entirely new type. Required was a positive type of action which would guarantee that the pulp flow be spread equally along the length of the drum. Discussion As indicated, the motivation for development was simple necessity. The plant in San Nicolas crushes, grinds, and concentrates magnetic iron ores of a particularly abrasive nature, and depends largely on magnetic separation to obtain a marketable product. Feed to the numerous drum magnetic cobbers and finishers varies from rod mill discharge at a nominal minus ten mesh to a ball mill fine grind of seventy percent minus three hundred and twenty-five mesh. Operational factors affecting the magnetic separators were well controlled,

Jan 1, 1971

By Robert L. Gamble

The world's largest fluidized bed steam generator located at Rivesville, West Virginia is currently undergoing initial operation. This unit is designed to generate 3708 kg/s (300,000 Ib/hr) equivalent to 30 MWe of superheated steam while firing coal in a fluidized bed of limestone. Coal was first fired in this unit in December, 1976 and start up operation is progressing.

Jan 1, 1977

By Zygmunt Sadowski

Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of chemical additives and metal ions present either added or present as contaminants, on the flotation. Fuerstenau and Palmer (1976) have studied in detail the adsorption of multivalent cations onto oxide and silicate minerals. It was observed that the adsorption of a multivalent metal species exhibits a sharp pH dependence which is related to the formation of hydroxy complexes of the metal ions in solution. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances cations such as Ca2+, Mg2+, Fe2+ and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions.

Jan 1, 1986

By James J. Broderick

In the production of Pig Iron - Limestone, Coke and Iron Ore pellets are changed to the blast furnace and reacted at approximately 2,800 degrees F. The resultant products are molten iron and a molten slag - not unlike lava. The molten slag stream is channeled into open pits, cooled with water, crushed and sized for various industrial applications. The production of steel from pig iron in open hearth, B0P, BOF and electric furnaces results in somewhat similar slags: but since free lime is normally the flux, the resultant slags are not satisfactory for use in cement pastes. When exposed to water, the lime slakes, expands by 250% and ruptures the concrete. Thus, the slag discussed first is Blast Furnace Slag composed of 30 to 40% Silica (SiO2) Alumina (AL202) 7 to 16% Lime (CaO) 32 to 45% and Magnesia (MgO) 5 to 15%. The oxides do not exist as free oxides but rather as silicates and alumino silicates which are chemicall inert. Since transportation costs limit the area of use, blast furnace slag can only be found in concrete products produced within 60 to 100 miles of a blast furnace operation. Even within these areas where slag is in heavy supply, quite often the use of slag is minimal for concrete aggregate and the major outlet is road base.

Jan 1, 1985

By Karl C. Dean

To assist in the reduction of environmental degradation resulting from milling operations, the Bureau of Mines has developed, and successfully demonstrated, chemical, vegetative, and combined chemical-vegetative procedures for stabilizing milling wastes under varying environmental conditions. Costs of achieving reclamation using these stabilization procedures are compared with those of other physical and vegetative approaches. The Bureau's chemical-vegetative procedure for establishing vegetation directly on fine-sized wastes compares favorably with other stabilization processes that have been used.

Jan 1, 1972

By J. R. Arnold

The problem of recovering gold from a cyanide solution has been plaguing metallurgists since the cyanidation process was discovered in Glasgow, Scotland.1 The "perfect" method has never been found and this paper will not purport to fill that gap. But we, at Gold Fields, feel that we have developed a workable, cheap and efficient method of producing a refinery - ready product that has several distinct advantages over conventional electroplating techniques. The Gold Fields replating system is presently being used at their Ortiz and Mesquite operations. In short, the system electroplates the gold out on stainless steel wool, instead of mild steel wool as is usually done, then replates the gold by reversing the current onto stainless steel plates. By doing this the steel wool can be reused many times, the gold can be scraped off the plates cleanly and quickly, the operating costs are reduced and the slag production is greatly reduced.

Jan 1, 1986

By Daniel C. McLean

Many of the major copper ore bodies throughout the world contain chalcocite (79.9% Cu) as the principal copper mineral, yet the grades of copper concentrates produced from these ores rarely exceeds 25 to 28% Cu and in one known instance went as low as 13%. The low grade has traditionally been attributed to the presence of "activated pyrite" and/or chalcopyrite, and the universal approach has been excessive regrinding with all of its inherent effects-high capital, energy and maintenance costs, excessive sliming, and concentrate filtration difficulties (high moisture content). E. P. Cadwell, former Chief Metallurgist for American Cyanamid Company, did extensive microscopical studies on several of these types of concentrates from South American operations during the 1950's and discovered they all had one common feature--the pyrite particles in the concentrate were all rimmed with thin films of secondary chalcocite or covellite. As far as a flotation bubble or reagent is concerned, a rim of chalcocite is the same as a solid particle of chalcocite, and as long as a rim is present, the particle is going to float. Upon examination of these rimmed particles under the microscope, it becomes quite obvious why regrinding will never solve the problem and why maximum increases in grade by this technique rarely give improvements in grade of greater than 3 to 5% Cu.

Jan 1, 1983

By Thomas R. Hightower

The Thunderbird plant was erected in Sullivan County in Indiana during 1958-1959. It was first put in operation in March of 1959. At the present time the source of the raw coal is from the Indiana No. 6 seam. The underground operation at present consists of two continuous mining units and two conventional units. The underground is all belt haulage and the first unit with which this paper is concerned is the slope belt. It is a 48-inch-wide inclined belt with 980-foot centers and a lift of 275 feet. The belt is powered with a 350 H, P, motor and has a rated capacity of 600 Tons per Hour. The belt is equipped with a Merrick Scale Company Weightometer, The raw coal moves from the belt to a 6'x12' extra heavy Allis-Chalmers Ripl-Flo equipped with 6" round-hole screens. The over product of the screen is fed into a 10'x20' long McNally- Pittsburg rotary breaker equipped with 4-l/2" round-hole screens. The oversize rock is discharged into a bin that is emptied with a refuse truck. The through-product of the breaker, along with the through-product of the Ripl-Flo, passes either directly to the McNally Giant washbox or to a 36" belt that transports it to a 1000-ton storage bin,' The change from either to the washbox or to the storage bin is made by use of a motorized gate controlled by the plant operator,

Jan 1, 1961

By Arthur L. Raub

During the last decade, there haven't been any great innovations in the design features of a copper concentrator. What has worked well in the past continues to work well, so that major breakthroughs have been minimal. Conservatism in the ranks also plays an important part. As a copper concentrator is not designed and built everyday, Davy was elated to have an important part in this project. This is the story of the design of the oracle Ridge Project located north of Tucson on the back of Mt. Lemmon at an elevation of 5,900 feet on the N.E. slope of the Catalinas. The Oracle Ridge property, formerly known as the Control Mine, is owned by Oracle Ridge Mining Partners, a joint venture between Continental Materials Corp. of Chicago and Union Miniere of Brussels, Belgium; both or¬ganizations specializing in the non-ferrous metal industry.

Jan 1, 1979

By Seppo] [Kreula

Outokumpu Oy has acquired considerable experience with on-stream X-ray fluorescence analyzers and with computer control of flotation processes over several years. It became evident at the outset of this work that a reliable and accurate on-stream analyzer was more than a collection of different pieces of hardware linked together. Extensive work was done to develop an integral analyzer system, beginning with process samples through the spectrometer to report typewriters, recorders and the control computer. To date, over ten Courier-300 analyzer systems based on this development have been installed world-wide, several of which provide the key information for successful computer control systems. Computer control of flotation processes has been under development at the Pyhäsalmi concentrator since 1968. Two different control strategies have been implemented. The copper flotation is controlled by means of a mathematical model and economic criteria, whereas the "evolutionary operation principle" is applied to the zinc flotation. The computer control system installed at' the Vuonos-mine has been developed according to the same guidelines. In order to consolidate this wide experience, a flotation computer control system, Proscon-100, was developed by Outokumpu Oy, and the first system was installed at Kotalahti in 1972. In addition to the technological experience, enough information has also been gathered to illustrate the economical, benefits accruing through the use of these advanced tools of automation.

Jan 1, 1973

By R. W. Leonardson

Tectonic activity in northern New Mexico during late Oligocene and early Miocene time presaged events which led to the development of molybdenite deposits at Questa. East-northeast directed crustal extension produced north-northwest striking tensional fracture systems paralleling the early Rio Grande rift. A sequence of Oligocene andesite flows and breccias is overlain by a thick early Miocene rhyolite ash-flow tuff. Eruption of the tuff initiated collapse of the Questa cauldron: the south margin of which occurs as an east-northeast striking, north-dipping structurally weak zone. Continued east-northeast post-cauldron extension permitted the high level emplacement of granite stocks with coeval rotational deformation of fault blocks composed of cauldron fill and [ ] floor. The stocks occupy north-northwest fracture zones in the south margin of the cauldron, and porphyry dikes occupy east- northeast striking faults that define the south margin. These two fracture systems have played a dominant role in localizing the intrusive porphyries and associated mineral deposits at Questa. A molybdenite-bearing breccia matrix and related stockwork mineralization generally occur within volcanic rocks. Mineral deposits are spatially related to fault zones and the upper con- tact of their source intrusives. Deposits are localized in fault zones up to several thousand feet long and 100 to 500 feet in diameter. Magmatic-hydrothermal solutions from the source aplite porphyries have produced potash metasomatic alteration which is strongly centered on the mineral and ore zones. Alteration in ore is represented by orthoclase, quartz and secondary biotite. This pattern grades into secondary biotite and propylitic zones forming successively weaker alteration assemblages away from ore. Younger phyllic and argillic assemblages are particularly widespread only where strong north-northwest extensional fracture zones cross the south cauldron margin.

Jan 1, 2013

By Gerhard Lang

"Slurry Microtunneling is a well-established technology building on over 20 years of experience in successful tunnel installations under all kinds of soil conditions across the U.S. and Canada. Recent microtunnel installations prove that initial hesitation, e.g. curved drives, is fading and long-distance pipe jacking projects as well as lake outfalls are being considered. One of the younger technologies is Direct Pipe®, which combines the benefits of HDD and Slurry Microtunneling. It fits exactly into the area where HDD is not feasible or too risky to apply. The paper points out the benefits of the Direct Pipe® technology for owners, engineers and contractors and discusses the latest developments of Slurry Microtunneling for long-distance, curved drives and sea/lake outfalls with wet recovery of the equipment such as on the ‘Keswick Outfall Project’ in Ontario. The first Direct Pipe® installation in the US was executed in August 2010. Since then, another 22 crossings have been carried out amongst a total of more than 60 Direct Pipe® crossings worldwide. INTRODUCTION Pipelines installed underground are indispensable for supplying the growing world population with water, oil, gas and electricity, for removing wastewater and for providing functioning telephone and communications networks. During recent years the limits of trenchless applications have been permanently shifted, leading to higher and more stringent project requirements and consequently new technologies, either as further development of existing methods, or through the development of new methods by incorporating elements of proven technologies. MICROTUNNELING TRENDS IN NORTH AMERICA Slurry Microtunneling has a wider geological application range in comparison to EPB and hard rock Microtunneling. The Slurry MTBM can be equipped with specific cutting wheels to cope with different soil conditions. The most flexible and most often employed type is the mixed soil cutting wheel, which contains a mixture of disc cutters as well as scrapers for varying soil conditions from cohesive soils (clay, silts) to highly permeable soils including sands, gravels and cobbles and even hard ground formations such as rock and boulders. A detailed geotechnical report provides the appropriate data to configure the MTBM and its features to the ground conditions expected. Mixshield or hydroshield (AVN/AVND) MTBMs in particular, can be safely operated with little overburden (~ 3-5 x machine diameter) and minimum risk of frac-out or settlement on the surface. This is especially beneficial in urban areas with sensitive buildings or for river crossings with protected fish habitats."

Jan 1, 2016

By R. K. Mensah-Biney, M. T. Hepworth, K. J. Reid

The loading characteristics of gold-bromide species onto activated carbon were evaluated using a batch system. The overall loading of gold onto activated carbon was rapid for the first few hours, but it continued without cessation as a result of the reduction of gold. Therefore, conventional equilibrium considerations were not applicable. Although loading continued slowly after several days, an abnormally high, loading capacity value of 10-12 meq/g carbon (650-800 kg Au/t) could be attained in 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of (AuBr4)- species to the external surface to be reduced to metallic gold by carbon. Elution of gold from loaded carbon was feasible provided the carbon had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical, and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon for gold-bromo species is discussed.

Jan 1, 1994