Search Documents

By M. A. Trevits

Methane gas is an ever-present problem facing the underground coal mining industry. Mine operators are mandated by law to maintain safe concentrations of methane gas within the mine environment. Ventilation is used by all mine operators to reduce gas concentrations. When gas emissions are such that ventilation alone cannot control the gas, methane drainage methods must be applied. In the 1970's, there was a concern that unprecedented gas emissions would be experienced as mine operators began new developments in the deep and gassy Blue Creek and Pocahontas No. 3 Coalbeds. Such concern was well founded as significant gas volumes are being emitted as these mining operations mature. In 1971, the O.S. Bureau of Mines began to tabulate and track the change in mine emissions. These data were extracted from the underground coal mine quarterly air quality-quantity inspections performed by the Mine Safety and Health Administration. At that time, approximately 6,560 Mm Id (231.7 MMcfd) of gas were emitted from 430 underground coal mines. It was determined however, that the mines emitting less than 2,832 m Id (100 Mcfd) contributed only 2.1 percent of the total daily gas flow. In 1988, underground coal mines emitted 8350 Mm Id (294.9 MMcfd) from 487 mines. This report evaluates the changing nature of U.S. mine gas emissions over the last 18 years.

Jan 1, 1993

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper evaluates the effectiveness of similitude theory in predicting the draft of a rubber tire loader’s bucket during initial penetration. The work uses 1:16 and 1:8 scale models of an 18-t capacity load haul dump, scaled with the Buckingham Pi Theorem, to evaluate the prediction of draft and penetration under different operating and different dynamic conditions. The authors hypothesize that the observed relationships between draft and longitudinal penetration and the operating and dynamic conditions will hold true for an upscaled model. Similarly, the authors hypothesized that the results of experiments conducted with the smaller scaled model should predict the draft on an upscaled model. The results show that the relationships between draft and longitudinal penetration and operating and dynamic parameters are similar for both scaled models. Similarly, the draft on the upscaled model, predicted by using the experimental results of the small model, is similar to the measured draft on the upscaled model. The mean difference between the two is 1.71 N with 95% confidence interval of [-3.51, 6.93], which is very good given the average draft is approximately 330 N. Thus, the work indicates that both hypotheses are true for draft. However, the work shows that scaling muck pile particle sizes using the Buckingham Pi Theorem is not adequate to ensure good predictions of penetration. This work provides insights that will help design engineers to acquire useful data on scaled models and use it for various analyses on heavy machinery.

Oct 6, 2021

By Donald C. Violetta

During 1963 more than 200 million tons of coal was consumed by the public utility industry. Ash residual, from the burning of this coal has caused disposal problems. In order to prevent air pollution, dust collection systems have been installed to suppress the fine ash emitted from boilers before it is discharged into the atmosphere. The collected ash, called fly ash, must be removed from the dust collection facilities and disposed in some manner, usually at a substantial cost to the utility. Many years ago fly ash disposal was not a serious problem because the demand for power was relatively low and coarse coal was burned on stoker type traveling grate machines. The low burning rates utilized on these grates did not produce large quantities of air-borne coal ash while the mechanics of this system of burning resulted in a clinkered residue of cinders. Both of these conditions resulted in the production of only small quantities of fly ash. As the demand for electricity increased, a method of burning pulverized coal was developed and was introduced to the public utility industry in 1918 at Milwaukee, Wisconsin.1 This method of firing was considered a significant advance in steam electric generation as it (1) permitted the use of coals that could not be economically fired by other methods and (2) has generally resulted in improved efficiency, greater generating capacity and lower costs.2 The utilization of larger generating units using pulverized coal substantially increased the quantity of fly ash which resulted in a' more severe disposal problem.

Jan 1, 1966

By J. N. Cox

Coal preparation is based on the properties of noncombustable materials (impurities) in coal being different from the organic constituents. The most commonly used property difference is density, via its affect on settling rates; and either gravitational or centrifugal forces can be used to remove impurities. However, examination of various particles settling rate correlations shows that at smaller sizes, particle drag becomes a very important factor. Classification, based on differential settling rates, becomes impractical and some property other than density must provide the basis for fine coal cleaning. Froth flotation and agglomeration employ differences in surface properties to clean coal. These methods are very successful except that the oxidized surface of a pyrite particle is somewhat hydrophobic and will tend to be collected with the organic portion of the coal. Surface property cleaning techniques have not been very effective in rejecting sulfur, except for two-stage flotation.

Jan 1, 1984

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine's accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By J. Brune, P. J. Coleman, L. Martini

Research in the field of mining safety and health in the United States plays an important part in protecting the lives of miners. The National Institute for Occupational Safety and Health (NIOSH) Mining Program conducts surveillance, studies and developmental work aimed at improving the safety and health of miners. With recent reviews of the Mining Program by the National Academy of Sciences and the Mining Program response (NIOSH, 2008), the importance of setting goals, conducting high quality engineering and scientific research and evaluating the outputs, outcomes, relevance and impacts of these projects has been reemphasized. Surveillance of reported injuries is a first step in deciding on research directions and in designing specific projects. Groups of injuries often share features and attributes that suggest common causes and may respond to similar preventive efforts. Identifying groups of injuries also serves to prioritize intervention efforts. The Mine Safety and Health Administration (MSHA) Accident and Injury database (MSHA, 2008) provides individual case reports of mining injuries, illnesses and certain no-injury accidents (events such as roof falls that stop mine production or miners’ activities for more than one hour). This database is an indispensable resource for researchers and stakeholders needing information on the statistics of these events. From an epidemiological perspective, research projects target groups of miners at risk due to specific patterns of work, equipment, mine settings and the management of safety and health in their mines. Incidence rates are provided by the MSHA data for selected variables, such as surface/underground location, standard industrial classification and state. While incidence rates are the preferred measure for all variables, denominators are not typically available; for example, to more clearly understand the data about injury by occupational type, it would be necessary to conduct demographic surveys. A current survey of the demographics of the mining industry should be complete by 2010, which will allow incidence rates to be developed for a number of variables such as age, occupation and experience. This survey will provide the first update of its kind since the first survey was conducted in 1985. This report describes an alternative method of analyzing and presenting MSHA data for the purpose of identifying high-cost, high-severity injuries and illnesses. Researchers at the NIOSH Spokane Research Laboratory (SRL) developed programs to find the top five most frequent accident classes, natures of injury, types of accidents and other selected variables from the MSHA database. Studying these variables gives a cross-sectional snapshot of the most frequent groups of injuries within a commodity, regional group or time period, and allows researchers to quickly understand developing patterns for new research projects. The primary benefit of this approach is to

Jan 1, 2009

By Rodolfo Lagos, Nicos Pfeiffer, Ben Harding, Clayton V. Deutsch

This paper documents a probabilistic resource modeling workflow for the Round Mountain epithermal gold deposit. The set of categorical and continuous variable simulated realizations provides a model of variability and uncertainty given the current orebody knowledge. These realizations can be used to quantify and understand expected deviations in reconciliation during mining and provide a more accurate measure of expected gold than an estimated model. Gold mineralization at Round Mountain is primarily contained within tertiary tuff units, which dip gently to the west and thicken towards the southern part of the orebody. Domain boundaries are modeled as combinations of lithology and alteration; alteration domains are constrained to be within the tuffs. Large-scale geologic uncertainty is strongly influenced by parameter uncertainty, particularly the input histogram. The spatial bootstrap characterizes prior global uncertainty in the input histogram for categorical and continuous variables. Categorical models are generated using hierarchical truncated pluri-Gaussian (HTPG) simulation. Continuous variable simulation is carried out within the simulated domain boundaries using trend models to account for non-stationarity.

Aug 19, 2023

By L. Zhou, A. Martikainen, G. Goodman

Continuous airflow monitoring can improve the safety of the underground work force by ensuring the uninterrupted and controlled distribution of mine ventilation to all working areas. Air velocity measurements vary significantly and can change rapidly depending on the exact measurement location and, in particular, due to the presence of obstructions in the air stream. Air velocity must be measured at locations away from obstructions to avoid the vortices and eddies that can produce inaccurate readings. Further, an uninterrupted measurement path cannot always be guaranteed when using continuous airflow monitors due to the presence of nearby equipment, personnel, roof falls and rib rolls. Effective use of these devices requires selection of a minimum distance from an obstacle, such that an air velocity measurement can be made but not affected by the presence of that obstacle. This paper investigates the impacts of an obstruction on the behavior of downstream airflow using a numerical CFD model calibrated with experimental test results from underground testing. Factors including entry size, obstruction size and the inlet or incident velocity are examined for their effects on the distributions of airflow around an obstruction. A relationship is developed between the minimum measurement distance and the hydraulic diameters of the entry and the obstruction. A final analysis considers the impacts of continuous monitor location on the accuracy of velocity measurements and on the application of minimum measurement distance guidelines.

Jan 1, 2012

By A. Mertzanis

The way and methods used for the surface mining of bauxite until the end of the twentieth century in the area of Ghiona, resulted in a significant burden to the natural environment, especially in the cases where it covered extended parts of forests and forest areas as well as important geomorphological formations. The impacts from the surface mining of bauxite which in fact constitute the object of this study relate mainly to the interruption of the natural continuity of the land relief and the alteration of the natural geomorphological activities and are due to: a) the alternating excavations with fronts of great heights, b) the depositions of large volumes of waste materials which originate from the revealing of the ore and c) the dense road network constructed in order to get access to the mine locations.

Jan 1, 2006

By I. Papadopoulos

Nowadays, geophysical prospecting is implemented in order to resolve a diversity of geological, hydrogeological and geotechnical problems. Though plenty of applications and a lot of research have been conducted in the country-side, only a few have been reported in the literature concerning urban areas, mainly due to high levels of noise present that aggravate most of the geophysical methods (e.g. electromagnetic, seismic, gravity etc.) or due to spatial limitations that hinder normal method implementation (e.g. electrical). Among all geophysical methods, electrical tomography proves to be the most rapid and urban noise insusceptible technique. This work presents a case study in the urban area of Hania (Crete I., Greece), where Electrical Resistivity Tomographies (ERTs) have been carried out for the detection and identification of possible buried ancient ruins or other manmade structures, prior the foundation of a building. Nineteen profiles were surveyed in a 20x40m grid using dipole-dipole configuration. The results indicate two areas of interest, that are interpreted as probable old wells, in the context of the existence, in former times and in the same area, of an olive oil plant. In the vicinity, near surface ancient ruins have been disclosed, but no such evidence provided this survey, for the particular area under study and the prospected depth. The collected ERT-data were processed by applying advanced algorithms in order to obtain a 3D-model of the study area that depicts more clearly and accurately the interesting subsurface structures.

Jan 1, 2005

By Caibin Wu, Bin Xie, Jiaqi Tong, Ningning Liao, Chong Zeng

Understanding the energy-size reduction relationship is vital to grinding process; therefore, this paper aims to show the energy-size reduction of magnetite-calcite binary mixture in a laboratory wet conical ball mill. Single magnetite, single calcite, and blended magnetite-calcite mixture at three weight ratios in four particle sizes were ground in a laboratory wet conical ball mill at four grinding time periods. The results showed that the particle size distribution of both fine particles and coarse particles of single and mixture ground product fitted well with the PSD computed by Rosin–Rammler-Benne function. The larger mass percentage of calcite is, the higher t10 of binary mixture ground product is. On the contrary, t10 in the mixture decreases as the percentage of magnetite in the mixture increases. The different breakage behaviors in blended samples are due to the hardness and particle size. The results of calculated ratio of energy absorption factor showed that the calcite consumed more energy in the breakage process of binary mixture than ground alone. The JK size-dependent breakage model based on the t10 method fits all the experiment data, be it generated from pure minerals, mixtures at different weight ratios, or each component separated from the mixture.

Jun 4, 2022

By J. C. Watts

Monitoring and control of conventional industrial wet grinding circuits is conceptually straightforward. However, since production objectives and operating constraints can vary widely from plant to plant, there is probably no single overall grinding circuit control strategy which is "best" in all cases; in-variably some compromise is necessary between performance desired under ideal conditions and performance achievable in practice. The recent advent of relatively low cost, reliable, high speed small computer systems is revolutionizing daily operations in increasing numbers of metallurgical processing plants. Of special power and capability is a hierarchical computer network like that currently in use at the Pinto Valley Operations of the Cities Service Company. Several satellite processors for key plant areas communicate with a master computer operating under a powerful multitasking real-time operating system. Hardware and software structure is such that downtime on one of the processors -including the master -does not have a major impact on overall system operation. Admittedly, the powerful, core efficient table driven satellite software, which handles process/computer communication, calculation of nonmeasured process variables, and basic Direct Digital Control functions, is difficult to modify. However, important high level process monitoring, report preparation, graphic display, and supervisory control functions -including economic optimization -can be implemented by project engineers at the plant site. Thus, for example, new control strategies can be quickly examined and rapidly evaluated. Such computer monitoring capability also permits use of short duration process pulse tests for approximate dynamic modeling and rapid calculation of controller tuning constants for single loop dominant systems. Following a brief back-ground discussion of the Pinto Valley Project, we present some of the more interesting results and conclusions of our work over the past year.

Jan 1, 1978

By K. E. Harrison

The acid rain legislation has passed into law. This new law has caused the power generation community to investigate alternative methods to obtain compliance with the new legislation. One thing all of the power companies have concluded is the answer is not easy. Do we switch fuels to burn all low sulfur compliance coal? Maybe possibly only partial desulfurization by means of a dry sorbent system? Or, finally, maybe a wet scrubber system? Whatever the choice, the power community needs to investigate all of the alternatives. In 1988, ICF Kaiser Engineers, Inc. (ICF KE) responded to a request by the U.S. Department of Energy for the engineering development of advanced physical fine coal cleaning. ICF KE responded and was awarded a contract to conduct a multi-task program to develop an advanced flotation system to eliminate pyritic sulfur and retain as much energy as possible. ICF KE assembled a team that included members of industry, academia, and industry research organizations to conduct this multi-task program. The program includes sixteen (16) tasks. This team had personnel to help solve some of the anticipated problems and to provide industry prospective on the viability and commercial potential for any concepts proposed. The primary team consists of a major coal producer, Babcock and Wilcox, Eimco Process Equipment Company, and Virginia Polytechnic Institute and State University.

Jan 1, 1992

By Dolf Vos

The balling section of the pelletizing plant at Hoogovens IJmuiden consists of 7 balling drums. Each with an average capacity of 100 tons of green pellets per hour. The balling drums are equipped with rotating scrapers and water-spraying systems. The scrapers are installed in order to restrict the growth of the race to a certain thickness. The spraying system is used to adjust the desired value of the moisture-content of the rewetted ground ore, the pellets and the race. The desired value is the value by which the balling- process is stable, good pellets are formed and surge occurs within certain limits. In October 1980 the construction of one of the balling drums has been modified. The rotating scraper was removed and the inner wall of the drum was supplied with a rubber-lining. In 1982 a second balling drum has been rubber- lined. At the same time the Tyler vibrating screen of this balling circuit has been replaced by a roller(bed)screen. By the end of 1983 all 7 balling circuits will be equipped with rubber-lined drums in combination with roller(bed)screens. The combination of these two modifications will improve the quality and the screen analysis of the green pellets, moreover resulting in savings on energy- and maintenance costs. This paper describes the influence of a rubber- lining on the balling process and the green pellet quality by carrying out in-plant testruns in November/December 1980. The testrun results have been compared with the results of a not modified balling drum.

Jan 1, 1983

By K. Lang

A test section of the upper most lift and underlying lifts of a large scale copper heap leach operation was instrumented and monitored with advanced wireline geophysics, fiber optics and resistivity electrode arrays. Elemental Capture Spectroscopy (ESC) copper measurements, resistivity measurements from an Array Induction Tool (AIT), electrical resistivity tomography (ERT) and distributed temperature sensing (DTS) with fiber optics provided integrated near real time data about the performance of the heap. During the leaching cycle, ECS provided continuous vertical measurements of copper in the upper most and underlying lifts in the test section of the heap and was used to generate a copper recovery curve. ERT inversion modeling provided high resolution 3D resistivity measurements, which were used to evaluate moisture distribution. DTS measurements of temperature were used to track the PLS front and calculate velocity. AIT induction provided highly precise bulk resistivity measurements. In-situ samplers provided PLS chemistry at multiple points. Properly integrated monitoring data can provide the heap leach operator with information that can be used to evaluate the hydrodynamics and metallurgy of the leaching process in near real time. Problems in the heap, such as pooling, channeling, longer lag and breakthrough times, excess acid consumption, increased solution in inventory, toe saturation and slope stability can be detected in near real time with the in-situ measurements evaluated.

Feb 23, 2014

By S. A. Rholl

This paper describes the Bureau of Mines experimental test program which evaluated the effectiveness of using high explosives to enhance orebody permeability. To determine the effect of stress on the fracture network generated by blasting, fifteen single-hole laboratory tests in granite blocks up to .067 m3 (2.4 ft3) in size were blasted using .12 to .20m (4.8 to 8.0 in) of 1.6xl0-3-, 3.2xl0-3-, or 6.5xl0-3-kg (25-, 50-, or 100-grain) detonating cord. In situ stresses were simulated using polyaxial load cells to apply uniform stresses of 1.72xl06 to 1.76xl07 Pa (250 to 2550 psi). All of the blocks were sawed to expose the blast-induced fracture patterns for analysis.

Jan 1, 1991

By Reed S. C. Rogers

There is recent evidence that high frequency screening can be a viable alternative to hydrocyclone classification for a wide variety of grinding applications. However, since high frequency screening is a relatively new development, the decision to use screens generally must be based on full scale screening tests of a slurry material of interest. In this paper the authors employ mathematical simulation models as an aid to evaluating the use of screens versus hydrocyclones for closed circuit fine grinding. This approach is validated in a pilot plant study and then demonstrated for the design of full-scale grinding circuit, including classifier cost comparisons. For the case of maximum production rates versus product size, without a constraint on fine product solids densities, results indicate that screening with Derrick sandwich type cloths can give higher grinding circuit production rates with more narrowly sized products than when hydrocyclones are used. These results are explained in terms of the bypass and Sharpness Index of the respective classifier partition curves. Classifier cost comparisons for the full scale circuit show that although the installed cost of screens is substantially higher than equivalent capacity hydrocylone operations, even modest increases in circuit capacity caused by screens; can significantly reduce total grinding costs.

Jan 1, 1985

By David L. Giles

The Lime Creek* ore body in northwestern British Columbia is one of the few commercial primary stockwork-type molybdenite deposits in North America. Others include the Climax, Urad-Henderson, Questa, and Endako ore bodies. They are mined on a low grade-high tonnage basis, and are open pit operations except for Climax and Urad-Henderson. Much recent geochemical research on both porphyry copper and stockwork MoS2 deposits has been concerned with dating of micas related to the mineralization and associated igneous rocks. The results appear to show that mineralization and the predominant magmatic events of the deposit are indistinguishable in age (1-5), except where dating has been in sufficient detail to resolve the analytical overlap (6). At Lime Creek, geologic information shows that the Main granodiorite, the major intrusive and dominant host rock for MoS2 mineralization, was emplaced and had solidified sometime prior to the introduction of MoS2. The first MoS2 episode is intimately related to localized bodies of kalialaskite which clearly intrude the older stock. K-Ar dating was undertaken to clarify the age relations between Lime Creek plutonism and the apparently younger hydrothermal event that began with kalialaskite.

Jan 1, 1975

By Richard L. Gordon, William A. Vogely

ENERGY POI.ICY-PRINCIPLES AND THEIR PRACTICE Persistently, at least since the end of World War 11, governments have intervened broadly, deeply, and incoherently in major energy markets. If we take a broad definition of energy that encompasses gas distribution and electric power, we can observe regulations of even older vintage. This trend, of course, is not unique to energy. Expansion of government controls has occurred in many areas. The relevant basic question about energy regulation, therefore, is not why is energy special, but whether any general principles exist to explain the wisdom of existing regulations. This review takes place at a time, the middle 1980s, in which a massive onslaught is being undertaken against government regulation. However, the present chapter is influenced primarily by my observations of the failures of energy regulations and not by any inspiration from those ideologically opposed to government intervention. Several subquestions arise in policy appraisal. A primary need is to establish clear objectives and determine the consistency between these goals and the policies imposed. Thus, the first step is to set objectives. The next is to outline ways to attain these goals. However, it should be recognized that many apparently distinct options are economically equivalent. When the goal is to charge producers or consumers for something, it is possible to attain the same result through either government ownership or taxing private transactions. The tax can raise the price to the level the government would have charged if it were the owner. Creation of a Department of Energy is not necessarily any different from having separate energy agencies well coordinated by some small supervisory body. Thus, a distinction should be made between substance and form in policymaking. The critical substance concerns such matters as whether the government imposes financial penalties, incentives, or rules to attain a goal. Then, there can be many equivalent ways to implement the basic policy form. The second prior illustration suggests that one favorite question is how to attain proper integration of policy. At various times, voices on either (or even both) sides of the Atlantic have called for a coordinated energy policy. The U.S. Paley Commission made this a primary goal for future policy. The western European governments that were the founding members of the Coal and Steel, Economic, and Atomic Energy Communities spent much time in the middle fifties and much of the sixties trying futilely to agree on an energy policy. (See Gordon, 1970 for an annotated review). The energy price rises of the 1970s rekindled United States interest in coordination. However, astute observers of the problem such as O. C. Herfindahl of the United States and Maurice Allais (1 962) in France warned the discussions confused form with substance. The crucial issues were what were the goals and what were the best types of policies to attain such goals. Policy suffered, not from poor organization, but from discord about the goals and how to attain them. All this suggests that we need principles to guide policy appraisal. The branch of economic theory known as welfare economics concentrates on providing guidance about the problems of policymaking. The theory examines both what

Jan 1, 1985

By Donald G. Rogich

The concept of initiating a large action-oriented contract, directed toward inherently safe mining systems, was conceived by the U. S. Bureau of Mines in January 1970. At that time we were in the process of establishing research contracts and grants, about 100 of which were let in FY 71 to deal individually with fairly specific technological areas. These projects in the aggregate covered a wide spectrum of health and safety problems. What appeared to be necessary was the creation of a project or program that would provide a focal point for the demonstration of many of the results of this research and also in the action sense culminate with working hardware and systems that could be tested and demonstrated over a fairly long teen. The concept of working demonstrable systems, rather than just a conceptual study, was, felt to be necessary for two significant reasons. In the development of any new system, the translation from concept to working hardware is usually a costly and time consuming process which acts as a deterrent to implementation. Secondly, many decisions in the mining community to change equipment or systems ,are based on first hand observation of the new system, in operational practice, an attitude which is certainly understandable in view of the high capital costs of equipment. The decision was made to procure a single R&D contract which would be aimed at developing underground coal mining systems which

Jan 1, 1972