Search Documents

By Don Painter, Nico Sutmoller, Lori M. K. Kahikina, Brian Dorwart

This paper will address the feasibility of using low-density cellular concrete (LDCC) for an annular fill application where project conditions required pumping the LDCC material for distances of up to 16,000 feet. These conditions occurred during construction of the Kaneohe-Kailua Sewer Tunnel in Oahu, Hawaii, between 2014 and 2018. Located on the island of Oahu, Hawaii, this 13-foot-diameter rock tunnel extends for approximately three miles from the Kaneohe Pre-Treatment Facility to the Kailua Regional Wastewater Treatment Plant. The tunnel was built to convey wastewater and provide temporary storage for peak wet weather flows entering the collection system, thereby reducing the potential for uncontrolled discharges. LDCC was chosen for this project partly due to its environmental benefits, which were essential for an application contiguous to the inland marine and coastal waters of the Pacific Ocean. In order to ensure optimal performance characteristics—compressive strength (with a requirement of 300 psi at 56 days), flowability, and light weight—were achieved, extensive testing of various LDCC products and mix designs was completed. The testing measured the initial set time of the LDCC as well as the compressive strength needed to reduce the quantity of grout lifts required for the project.

Jun 13, 2021

By William Gleason

"While the American Exploration & Mining Association (AEMA) was preparing to close one chapter and begin another during its annual conference in Spokane, WA Dec. 3-7, word of a significant victory on an issue that has been important to the association for many years came from the halls of Washington, D.C.During a keynote address on Dec. 6, Joe Balash, assistant secretary of Land and Minerals Management for the U.S. Department of the Interior (DOI), told a sold-out lunch crowd that the DOI had released final drafts of proposed revisions to the Obama-era greater sage grouse conservation plans. The revisions suggest removing hundreds of thousands of acres of federally protected habitat in Utah, and easing restrictions on energy development and other activities, including mining, in Colorado, Idaho and Wyoming.The protections of the sage grouse were put in place by the Obama administration in 2015. The sage grouse, a prairie fowl, is considered by conservationists to be a key indicator species for the health of America’s sagebrush ecosystem. The previous plan to protect the ground-dwelling bird imposed restrictions to development in sage grouse habitat, but did not place the birds on the endangered species list — a move that many believed would have imposed far more rigid rules.AEMA, and its executive director Laura Skaer, led the way in the fight against the Obama-era greater sage grouse plan, arguing that the plan unnecessarily hurt economic development.“We were the first organization to point out that the greater sage grouse was being used to stop mining, oil and gas production and grazing on public lands in the interior mountain west,” said Skaer who is retiring from AEMA with a significant legal win on this front. “Early on, we cautioned that the proposed Land Use Plan Amendments would be worse than a listing (of the sage grouse) under the Endangered Species Act. Very few believed us until they saw the plans with all of the restrictions and the recommendation for a 4-million-ha (10-million-acre) withdrawal from mineral entry. We were the only organization that filed comments on all 88 Land Use Plan Amendments in 11 states covering more than 24.2 million ha (60 million acres).”"

Feb 1, 2019

By Xianyang Qiu, Xiuzhi Shi, Chen Xie, Xiaofeng Huo, Yanhai Wang

In upwards medium-deep hole cut blasting, many confinement effects exist due to the small number of free surfaces, which is mainly provided by an empty hole. If the cut blasting effect cannot meet expectations, then subsequent blasting construction will be seriously affected, and large security risks to operators in the stope can be induced. The number of free surfaces is directly related to the layout of the cutting borehole. Therefore, it is necessary to optimize the layout of the first round of cutting boreholes. Theoretical analysis, numerical simulations, and field tests were used to study the formation process of cut blasting and optimize the layout of the first round of cutting boreholes. Based on the blasting parameters in the field, LSDYNA software was used to establish cut blasting models with four kinds of borehole layouts in the first round. The RHT constitutive model was used to simulate the rock-breaking effect. The numerical results show that the cut blasting effect is optimal when Nos. 3, 5, 7, and 9 are charge holes and Nos. 1, 2, 4, 6, and 8 are empty holes. In addition, the greater the number of empty holes, the larger the release space and the better the cut blasting effect. The uniformity of the empty hole distribution, namely, the uniformity of the release space, also affects the cut blasting effect. The field results indicate that a good cut blasting effect can be achieved by optimizing the borehole layout.

Sep 7, 2023

By M. S. Celik, H. Du, J. D. Miller, F. Cheng, O. Ozdemir

"In this paper, recent progress with respect to the flotation chemistry of soluble salt minerals is reviewed, and some of the more relevant issues including the hydration states of ions, the interfacial phenomena of salt surfaces and the flotation behavior of selected soluble salts are discussed. Due to the high solubility, the flotation of most soluble salts has to be carried out in their saturated brines. Anecdotal evidence has suggested that the hydration states of the ions have significant influence on the physicochemical properties of the solutions, the surface charge and wetting characteristics of the minerals, the collector adsorption states and, further, the flotation behavior of the soluble salts. In this regard, reviewing past research findings, efforts are made to establish a correlation between the ion hydration states with the flotation behavior of the soluble salts. Further, advances in understanding the significance of colloid adsorption involved in the soluble salt flotation process are addressed, and future research efforts to understand the soluble salt flotation chemistry are suggested.IntroductionSoluble salt minerals are essential raw materials for the production of a variety of commodities, fertilizers, potassium hydroxide, soda ash, magnesium compounds and other chemicals. These soluble mineral resources can be processed using flotation technology and, currently, more than 80% percent of the world’s potash is produced by the selective flotation of KCl crystals (sylvite) from other salt crystals, predominately NaCl (halite) and other more complex salts (Searls, 1990). Despite the successful application of flotation technology in the potash industry, the mechanisms for collector adsorption on soluble salts have not yet been fully understood and, therefore, have been of considerable interest to flotation researchers for many decades."

Jan 1, 2015

By Robert L. Randall

The mineral industries have a continuing need for market forecasting and analysis for a variety of purposes, among which are organization and control of the sales effort, financial and corporate planning, and evaluation of the anticipated revenue from investment in proposed projects. For anything beyond the simplest extrapolation, some kind of economic reasoning or analysis is called for, which may or may not be incorporated into a formal or quantitative model. The principles described here apply to most of the commercially significant minerals and metals. The examples are drawn largely from the copper market, as it is the one with which I have the most practical experience. Practical forecasting is the process of analysis and synthesis from three categories of knowledge: facts and statistics, theory, and practical knowledge and informed opinion. Although many attempts have been made to build forecasts on only one of these three pillars, none has been successful as an operating procedure because of the lack of balance. There are no facts about the future-only about the present and the past. Facts can illuminate the future, but the future can be described only in terms of probability or more or less likely states of affairs-not as a continuous extension of the past and present. Likewise, theory, although useful as an organizing discipline and for providing a methodology of analysis, is inadequate for the complexities of reality. This is especially so when there is feedback between plans and forecasts to produce a new outcome and when there are significant elements of unpredictable free will, such as presidential jawboning or foreign policy considerations. Such elements are difficult to accommodate in neat theories, although they must certainly be reflected in the forecasts. Pure opinion frequently suffers from both a lack of-disciplined reasoning and the presence of biases or self-interest. While the future is unknown, it tends to cast its shadow before it; hence, forecasting is the art and science of positioning oneself so that the shadow becomes visible to the forecaster.

Jan 1, 1979

By M. A. Cristovici

The possibility of using surfactants as wetting agents for the suppression of sulphide ore dust has been investigated. Numerous surfactants were examined to determine their characteristics and to investigate their ability to improve the wetting of the sulphide ore dust. However, the surfactants selected as suitable dust suppressors proved to have a negative effect on the flotation of the ore contaminated with such reagents. A method was developed to eliminate the detrimental influence of dust-suppressing surfactants. It consisted of surfactants adsorption on activated carbon and separation of loaded carbon prior to flotation. The technique is simple and requires minimal changes in the plant flowsheet.

Jan 1, 1990

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

P.T. Freeport Indonesia's latest expansion has increased total mill throughput to 125,000 dry metric tonnes per day. The most recent expansion included the installation of a Semi Autogenous Mill designed to treat more ore than any other single SAG mill currently operating in the world. Also included in the expansion were two large ball mills, rougher and cleaner flotation including conventional and column cells and a regrind circuit. All equipment is supported by a modem distributed control system. This paper describes the design considerations, construction, commissioning and start-up of the SAG concentrator and support facilities and includes an overview of the oreflow and milling facilities.

Jan 1, 1996

By Stephen H. Stow

The relationships between the amount of light reflected off 21 samples of Florida phosphate and the chemical, composition of the samples were examined. It was found that the reflectivity of a rock is directly related to its chemical composition and that darker phosphates (less light reflectance) have relatively high amounts of iron, organic C and sulfate while lighter-colored rocks were rich in phosphorus, fluorine and aluminum. The use of reflectivity measurements could have economic applications in the phosphate rock industry: color specifications for rock shipments could he met, beneficiations by optical sorting could be performed and semi-quantitative analyses could be made rapidly and inexpensively.

Jan 1, 1971

By Michael J. Mankosa

Increased emphasis has been placed on recycling consumer and industrial waste products. This trend has created a new industry that is focused on recovery/ separation of byproducts from waste material. As a result, interest has increased in the development of separation systems designed for the recycling industry. Much work has been done in this area. However, existing techniques developed for minerals beneficiation are often ignored. An example of is the foundry industry. There are currently more than 3,000 foundries in operation throughout the United States. Each consumes between 9 and 900 t/d (10 and 1,000 stpd) of sand for mold production. Either silica, chromite or zircon is, used in various combinations with chemical or clay binders. After casting, the sands are typically discarded into a landfill. This practice has become an environmental concern, especially the disposal of chromite and zircon. Silica sand is not environmentally sensitive. But it is used in greater abundance (6 to 7 Mt/a or 6.6 to 7.7 million stpy)and thus has prohibitive haulage and landfill costs. Current technology for sand reclamation involves thermal treatment to remove residual binders followed by dry mechanical attritioning (Leidel, 1993; Klein, 1994). This approach results in high losses due to fines generation and high costs associated with thermal treatment. As a result, this approach has shown only limited success. Stringent regulations are also affecting the disposal of secondary materials, such as plastics and metals. This is particularly true for the ferrous and nonferrous scrap metal industry. It plays a major role in industrial recycling of steel, aluminum and copper. Applications such as wire recycling present challenging problems since a hazardous byproduct (plastic insulation) is generated by the recycling.

Jan 1, 1997

By Joern Katzer

It is vitally important to any tunnel project to have an accurate and reliable survey control network inside the tunnel for layouts, as-built surveys, and to provide guidance to the tunnel boring machine (TBM). However, the concepts and methodology to provide such a survey network are sometimes not well understood. For example, the first anticipated survey task that takes place during the bidding process is often ignored, which is to provide a comprehensive survey network preanalysis for the surface network and tunnel traverse based on survey statistics that will be used to make informed decisions on the survey requirements and methodology. Instead, these steps are often only vaguely based on previous results and prior tunneling experience. But each tunnel is different, and a solution that worked for one tunnel project might be unsuitable for another. The purpose of this paper is to provide tunnel project engineers, managers and surveyors with the general concepts for tunnel survey methodologies and examines several statistical tools for a basic horizontal and vertical tunnel survey preanalysis. These survey statistics tools provide useful estimates of the expected lateral and vertical tunnel traverse accuracies, but are not a replacement for a comprehensive tunnel network preanalysis. The proposed formulas do not take centering errors into account, are using average distances for each traverse leg, and assume that the survey data is free of outliers in the measurements. It is very important that the estimated instrument accuracy is based on true values that are reflective of measurement precisions that are actually achievable inside the tunnel to provide accurate results.

Dec 1, 2022

By H. Jiang, Y. Luo

The study develops an automated, high-efficiency drilling control system to reduce respirable dust and increase energy efficiency in underground coal mines. It uses specific energy to evaluate efficiency and proposes a comprehensive drilling control algorithm based on laboratory tests. The algorithm optimizes drilling parameters to maintain high efficiency, reduce dust generation, and improve safety.

Feb 12, 2022

By R. M. LaDouceur, C. A. Young, W. Nicholas

"Salicyl hydroxamic acid (SHA) adsorption on two rare earth oxides, lanthanum and yttrium, was studied. Adsorption at both surfaces occurred in two stages. Initially, the monovalent anionic collector appears to adsorb significantly and instantaneously in stage one and then becomes sluggish in stage two presumably because the initial stage passivated the surface. By comparison, adsorption during the sluggish second stage with lanthanum oxide did not stop but with yttrium oxide essentially stopped. Surface monolayer formation could not be observed in either of the two cases. Both stages appear to be due to multilayer formation of a surface precipitate as proven by Raman Spectroscopy for lanthanum oxide but inferred for yttrium oxide. Unlike the use of octyl hydroxamate as stated in the literature, increasing temperatures do not increase adsorption such that flotation of rare earths with SHA may be performed at room temperature leading to improved recoveries as well as significant energy savings. INTRODUCTION Rare Earth Elements (REEs) are comprised of the 15 lanthanides along with scandium and yttrium. The REEs with lower atomic numbers are relatively more abundant and are categorized as light REEs. On the contrary, the REEs with high atomic numbers are less abundant and referred to as heavy REEs. They are not really “rare” and, in fact, some of them are quite abundant in the Earth’s crust; it’s just that they “rarely” exist in concentrated deposits but rather are found dilute and practically everywhere. REEs share very similar physico-chemical properties but, because many of these properties are unique, they have gained enormous importance in recent times making several critical and strategic pending their use. For example, REEs have found extensive application in phosphor coatings, magnetics, and automobile cracking catalysts. Early technology was not advanced enough to produce commodity level production of the REEs and can be attributed to REE-bearing ores containing many rare earth minerals (REMs), not just one. In this regard, there are numerous REMs but bastnaesite, xenotime and monazite are considered to be the most common. Bastnaesite is a fluorocarbonate whereas the other two are phosphates. The separation of the individual REE-bearing minerals from the ores is not an easy task since they also exhibit very similar properties. Consequently, when flotation is used, it is done to produce bulk REM concentrates. For REM flotation, it is well established that octyl hydroxamate is more selective than fatty acid collectors (Pradip and Fuerstenau, 1983 and 1991). Liu et al. (2006) indicated that hydroxamates are the most common collectors for REMs. Pavez et al. (1996) studied the adsorption of oleic fatty acid and octyl hydroxamate on REM surfaces. Cui et al. (2012) studied the interaction of octyl hydroxamate with various REMs surfaces using various spectroscopic techniques such as XPS, FT-IR and Raman along with electron microscopy and concluded that such techniques offer ample information to establish adsorption mechanisms. Ren et al. (1997) studied napthalenic hydroxamic acid as a unique collector for flotation of REMs from bastnaesite ore and indicated that more selective collectors were needed. From these studies, it is clear that the quest of more selective collectors is essential but understanding how they adsorb at mineral surfaces is prerequisite to improving flotation performance."

Jan 1, 2016

By Deniz Akbay

The strength of rocks and soil is a crucial design parameter in engineering projects, and it can be determined through various test methods such as uniaxial compressive strength, tensile strength, and shear strength. The point load index test is a popular indirect test method for predicting the uniaxial compressive strength of rocks. However, the reliability of the point load index’s estimation of uniaxial compressive strength of rocks is questioned due to the wide range of coefficients that are used to predict uniaxial compressive strength of rocks using point load index values. Factors such as the shape and type of rock specimen, practitioner, and test apparatus used can affect the accuracy of the point load index test. This study investigated the effect of four different specimen shapes used in point load index test (diametral, axial, block, and irregular lump tests) in predicting the uniaxial compressive strength. The rock samples were tested using four test procedures which are called diametral, axial, block, and irregular lump tests. The results showed that the irregular lump test was the most accurate in predicting uniaxial compressive strength, with the highest correlation coefficients and lowest mean absolute percentage errors. The point load index test can be used as a reliable predictor of uniaxial compressive strength of rocks when the irregular lump test is preferred.

Oct 18, 2023

By S. Chander

A series of nonionic and anionic surfactants were tested to enhance the flotation response of a low rank coal. An ethoxylated octyl phenol and several polypropylene polyethylene block copolymers were tested as nonionic surfactants. The anionic surfactant was a dioctyl sulfosuccinate. All the surfactants employed improved the yield significantly but the influence on grade was complex. Separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents tested, a correlation between emulsifying power of the surfactant and flotation was observed. An increase in the number of droplets produced in surfactant containing systems was considered to be the main reason for increase in the yield. Since it increased the number of collisions between dodecane droplets and coal particles. When a surfactant was introduced into the flotation pulp prior to addition of dodecane, it decreased the benefits of the surfactant significantly. The decrease was attributed to an increase in the wettability of coal and a decrease in the surfactant available for emulsification. When a suitable surfactant was added as a solution dissolved in the oily collector, a considerable increase in yield was observed.

Jan 1, 1993

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

To solve the problem of time-consuming and low precision in updating the open-pit vehicle transportation network, a high precision road network model construction method for unmanned vehicles in open-pit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3 + C (DeepLabv3 + Concat) is presented. Then, the road information extracted by the DeepLabv3 + C network is used to construct a three-dimensional model of the open-pit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicle meeting in open-pit mines, a vehicle meeting strategy was proposed. This strategy is used to guide the navigation of unmanned vehicles in open-pit mines. Besides, the DeepLabv3 + C network is verified by comparing the mIOU (means Intersection Over Union), accuracy, and continuity of road image extraction with the mainstream networks. The road network model constructed in the first step is quantitatively analyzed, and its performance is compared with GPS trajectory clustering methods. At the end of the paper, vehicle running simulation is carried out on the road network model by using Unity (a 3D visualization simulation software). The results show that the road network model constructed by this method can meet the navigation requirements of unmanned vehicles in open-pit mines, and the feasibility of the vehicle meeting strategy is proved.

Jan 11, 2022

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022

By J. F. Cornelsen

Wheel loaders are currently being used in many mining applications for a variety of reasons. While they sometimes provide the lowest loading cost, a primary advantage of the wheel loader versus other loading systems is the increased versatility and mobility inherent in a wheeled vehicle. The advent of large wheel loaders with much greater digging capability enhanced wheel loader usage in severe loading applications. To match these severe conditions, machines offered today were designed to work in these rocky conditions. Soon after the introduction of large wheel loaders into rocky conditions, however, it became apparent to many users that tire costs could at times account for up to 50% of total hourly operating costs on large wheel loaders. In some applications, tire costs alone pushed wheel loader economics beyond the economic feasibility for these jobs, prohibiting their use. In an effort to combat high tire costs, several attempts have been made to put fast moving steel around the tires to provide a strong interface between vehicle and ground. Some earlier attempts involved wrapping tracks around tires. Mechanical difficulties with these systems limited their customer acceptance. Subsequently, the development of protective tire chains came into favor. While tire chains offered added protection to the tires, the cost and maintenance of the chains remains a problem in 1972, the Dystred arrangement was announced for usage on a 6 cu yd wheel loader from Caterpillar Tractor Co. (See Figure 1). The Dystred offered the advantages of greatly increased tread life over conventional tires, as well as resistance to tread puncture in most situations. The arrangement basically employed a track system similar to that used on track type loaders. Pin and bushing wear often caused high hourly operating costs and excessive machine downtime. In addition, the connection of shoes through the use of links, pins, and bushings forced a limitation on too speed of the vehicle.

Jan 1, 1976

By Yinan Zhang, Y. Luo

Most of the reported coal spontaneous combustion events occur in surface and underground mines where low rank coals (i.e., subbituminous and lower for this particular studies) are extracted indicating their high propensities for spontaneous combustion. Low rank coals have high moisture content (15 to 45%) and are capable of absorbing more moisture in dried condition. However, it is hard to induce the initial stage of self-heating process for the low rank coal using the current laboratory R70 testing method — a method widely used in the coal industry. Like a sponge, dry low rank coals can absorb water vapor in the air while the heat contained in the moist air is transferred to coal and served as the required activation energy to initiate the coal self-heating process. In order to prove this theorem and quantify the effects, the R70 adiabatic oxidation testing method has been improved to introduce a controlled moist flow into the coal reaction vessel. Tests using the new method and its setup on low rank coals showed that the initial self-heating process of coal sample can be greatly accelerated by the added water vapor — impossible with the regular R70 method. Once the self-heating is sustained, the removal of air moisture can further accelerate the process.

Sep 17, 2021

By Dongjie Zhang, Shuxin Liu, Jianduo Wang

Broken rock mass and unreasonable stope structure parameters can cause excessive ore loss and dilution in sublevel caving; this is the main problem faced by caving mining in recent years. This paper proposes a stope structure parameter optimization method suitable for steeply inclined medium-thick broken ore bodies and evaluates the reliability and effectiveness through case studies. To solve the problem of large ore loss and dilution in the high-end wall sublevel caving method of Xilinhot fluorite mine, it is necessary to select proper stope structure parameters. Based on the theory of random media, an end-wall ore drawing experiment was carried out, and the bulk flow parameters needed to optimization of stope structure parameters were determined. In the experiment, it was found the draw-out body of high-end wall ore drawing showed a fine top and a thick bottom; the granular media had good fluidity. The reasonable caving step is determined to be 1.2 m instead of the 1.6 m originally used. Through the optimization experiment of the mining route position along the vein, the study found that the best route position is different with the ore body inclination. When the inclination angle of the ore body was 90°, the reasonable route was located in the center of the ore body. When the inclination angle of the ore body was between 85° and 90°, the route moved from the center of the ore body to the footwall at a rate of 22.5%. When the inclination angle of the ore body was between 80° and 85°, the route moved to the footwall at a rate of 54.8%. When the inclination angle of the ore body is not greater than 80°, the route should be arranged on the boundary of the footwall. Field application results showed the dilution rate reduced by 7.66% and the recovery rate increased by 7.31%. Field test results verify the effectiveness and applicability of the optimized stope structure, which corroborates the effectiveness and applicability of the optimized stope structure.

Mar 10, 2022