Search Documents

By Bright Oppong Afum, Kojo Boakye, Kwaku Boakye

This research developed and simulated a novel multi-indicator Fatigue Detection and Alert System (FDAS) designed to enhance fatigue detection accuracy in mining environments. The system integrates a comprehensive set of inputs: eye blink rate, eye closure duration, yawning frequency, distraction levels, Pre-shift Check-in Scores (Self-report) and Electroencephalography (EEG) Levels. Using MATLAB’s Fuzzy Logic Rule Viewer (FLRV) and Simulink, simulations demonstrated the FDAS’s robust ability to process these diverse physiological and behavioural indicators accurately. It effectively classified operator fatigue into low, moderate, and high fatigue levels, consistently providing appropriate outputs and corresponding intervention recommendations across various mixed-signal scenarios. The system achieved a calculated accuracy of 85.19% across 27 test entries, with a standard deviation of approximately 1.8459, confirming its reliability for real-time fatigue monitoring. These findings highlight the significant potential of this fuzzy logicbased approach to proactively identify early signs of fatigue, substantially enhancing safety and operational efficiency in demanding mining operations.

Feb 22, 2026

By L. B. Hales

December 3, 1972, James Wm. White presented the results of an instrumentation and process control survey which was sponsored by the Anaconda Company at the annual Tucson Subsection AIME meeting.(1) Twenty-six responses were obtained from questionnaires sent to 48 operating plants throughout the world. The survey results were discouraging in that there were more failures and problems than examples of success. The following quotes are taken from the text of the paper. "We run our mill by the seat of our pants." 'If these blue sky Ph.D.'s (in the instruments and controls area within research) had some operating experience they wouldn't make a lot of the suggestions they do."

Jan 1, 1981

By Andrea B. Baldwin

In recent years, federal and state regulatory agencies have tightened air emission standards. Two of the acid gases, hydrochloric acid (HCI) and sulfur dioxide (SO2), are under heavy scrutiny for reduction. . Most traditional scrubbing systems, i.e. wet scrubbers and spray dryers, meet the standards but they typically are high in capital cost, have significant space requirements for equipment, and are difficult to maintain. Dry sodium injection (DSI) is a alternative technology that has been shown to be effective in HCl and SO2 removal while being the inverse to the problems listed with traditional systems. This paper covers the mechanics of dry injection scrubbing using the most effective sorbents, sodium bicarbonate and mechanically-refined trona (natural sodium sesquicarbonate). It presents DSI performance data for Chambers Medical located in Hampton, SC. This facility incinerates local medical and municipal solid waste. Chambers Medical has used mechanically-fined trona for HCl and SO2 removal since late 1991.

Jan 1, 1995

By Yanli Huang, Qiang Sun, Jixiong Zhang, Yuzhuo Jiang, Dan Ma

Mining accidents due to inrushing water are caused by sudden changes in seepage owing to structural damage to key strata of the aquiclude. The backfill mining method can be used to control the movement of the strata, weaken the evolution of fractures owing to damage by key aquiclude strata (KAS), and control the channel for inrushing water. This study develops a mechanical model of a composite beam on a non-uniform elastic foundation of the KAS by analyzing the coupling relationship between the filling body and the key water-resisting layer of the aquiclude. Equations of the deflection-induced deformation, bending moment, and maximum tensile stress of the KAS are analyzed, formulae to calculate the allowable tensile stress and backfill materials’ compaction ratio (BMCR) to ensure structural stability are derived, and are used to provide the critical BMCR for their structural instability. The results of field measurements show that the subsidence of the roof was 600–700 mm with an average BMCR of 80.63%. Damage to the overlying strata was controlled to ensure safe mining and the disposal of solid waste from the aquifer. The research here is useful for ensuring safety during mining while protecting water resources.

Jul 12, 2022

By Ehab Gomaa, K. A. El‑Nagdy

Backfilling material such as tailing (mine wastes) mixing with cement or gypsum has grown throughout the world’s underground mines. However, despite their growing popularity, the typical hydraulic and mechanical fill types utilized in many mines still exist. Deep underground mining has increased due to the lack of commercial minerals nearby. Mine wastes were considered the main part of backfilling to prevent environmental pollution, ground subsidence after mine abandonment, and mine collapse during deeper extraction phases. The cemented backfill technique is the principal technique used in underground mines, which include cement with fly ash and/or filter dust, cement with tailing material and fly ash, gypsum with fly ash, and synthetic anhydrite with fly ash and have been reviewed. It has concluded that a backfilling material must be selected based on further goals, available material near the mine site, and economic factors. This paper analyzes different backfill material mixtures to create a technique that will increase safety in underground mining conditions and foresees an appropriate formula that gives high uniaxial compressive strength. The multiple linear regression (MLR) on the collected data from the experimental works to construct the relationship between the uniaxial compressive strength (UCS) of the mixture and the components of the backfilling and the prediction formula for expected compressive strength was obtained. The results revealed that the predicted regression equation was robust and reliable to predict the (UCS) for the new components of the filling (cement (CE), filter dust (FD), water content (WC), and time (T)).

Oct 3, 2023

By John Hanna

Recently. researchers at The University of Alabama have developed a two-step method for the treatment of phosphorus sludge that includes bulk removal of phosphorus by physical separation techniques followed by remediation of the residual P4 in the sludge using a novel wet air oxidation technique known as "HSAD", Tests made on samples of the electric furnace phosphorus sludge have demonstrated that essentially complete and fast removal of the P4 in the sludge can be achieved by the HSAD wet oxidation treatment, Further studies were made to determine the applicability of the two-step process on sludges of various origins. P4 contents different pre-treatment and storage conditions, The present work discusses the mechanisms and factors controlling the HSAD wet air oxidation remediation approach.

Jan 1, 1992

By Ray E. Williamson

One of the prime objectives of the mine industry is to develop a low cost way to clean up what has been called "The Rape Of Mother Nature". The project falls under the broad umbrella of reclamation, which is now considered an essential part of the mining cycle. As such, it is being given full consideration in the initial planning of all surface operations. In most areas, if a proposed mining system does not lend itself to proper reclamation, it is not an acceptable system. By combining mining and reclamation plans, a producer not only can minimize reclamation costs, but can also restore the land to usefulness and insure continuing profits after a deposit is depleted. As long as fifteen years ago, many of the larger mining companies were already deeply involved in this extra cost work. Even then the involved companies were projecting a great need for a bigger bulldozer, Bigger than anything commercially available. At that time, the D9 tractor weighed about 60,000# bare weight.

Jan 1, 1975

By H. M. King

A combination of chemical, statistical, geographic, and microscopic analyses reveal that sulfur in West Virginia coals is extremely variable in both form and abundance. Coals in southern West Virginia typically contain less than 1% total sulfur with organic sulfur being the dominant species. Northern West Virginia coals average about 2% total sulfur, mainly contributed by sulfur minerals. In addition to these regional trends, significant variations in sulfur form and abundance exist both vertically and laterally within individual seams. On both regional and local scales, the pyritic sulfur component can vary significantly in mineralogy, particle shape, maceral association, and particle size.

Jan 1, 1986

By J. Drelich

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size and distribution of mineral inclusions in coal on its wettability are briefly reviewed.

Jan 1, 1999

By T. Marcher, C. Mathiesen, M. Allende, S. Bauer

"A unique pumped hydro storage facility using the ocean as a lower reservoir, combined with solar PV to create consistent, clean power will be presented: the Espejo de Tarapacá Project is comprised of a 300 MW seawater pumped storage hydroelectric plant using the Pacific Ocean as its lower reservoir and an existing natural concavity at the desert as its upper reservoir. The plant site is located in Chile’s northern coast 90 km south of Iquique. The site is characterized by a rocky shoreline and about 600 m of flat terrain moving inland, with an abundance of rock outcrops, after which there is a steep 700 m cliff. The power house and all waterways will be underground. The main focus is to present the rocks being expected in the underground works. As one of the actual most tectonically active regions of the world the seismic activity is particularly relevant and will be outlined in the presentation. INTRODUCTION Valhalla Energy is an independent Chilean-owned power development company. It focuses on the development, ownership and operation of renewable power projects. Valhalla was founded in 2011 with the goal of developing Chile’s natural renewable energy resources and strategically diversifies the country’s energy matrix away from an overdependence on imported fossil fuels. Valhalla began developing pumped storage hydro projects to provide scalable, clean, competitive, and reliable electricity by combining Chile’s superior solar resources with the country’s unique and extensive coastline suitable for storage.The capacity for renewable energy supply is driven by two distinct and unique natural characteristics found in northern Chile: (1) the abundant and reliable solar irradiation in the Atacama Desert and (2) a coastal site that benefits from a steep cliff and a natural concavity both within a relatively small land mass (see Figure 1). There are several potential sites in the northern part of the country that can be developed. The “Espejo de Tarapacá Project” is the first one to be built and subject of the present paper."

Jan 1, 2016

By J. L. Ellenberger, G. S. Esterhuizen, T. Miller, M. M. Murphy

A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor convergence monitors were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.

Jan 1, 2015

By Jacques B. Wertz

It is well known that the major fractures and lineaments presently recorded in Western North America are preferentially oriented along a general northwest direction (Figure 1). There are other features, however, more subtle, more elusive as a rule and which can only be inferred, occurring at right angle to this broad NW direction. It is intended a) to examine some of these NE or transverse trends, b) to compare these regional NE breaks to similar ones that transversally cut through the eastern part of the European Tethys, more specifically in Iran and Turkey, and c) to study their potential relationship to mineralization in both areas.

Jan 1, 1973

By G. Ferrara

During several years of operation in Europe, South Africa and other countries, the Tri-Flo has demonstrated to represent a substantial improvement of the dense medium dynamic separation systems. The reasons are: (1) high sharpness separation due to the multistage system and the application of new concepts in designing the regeneration circuit and controlling the medium rheology; (2) the possibility of performing two cuts at different densities using a since separation device and a single regeneration circuit. The paper discusses in detail the above mentioned points, with particular reference to the multistage technology, based on the circuit analysis theory, and to the control of the medium rheology based on recent work in the modelling, and simulation of the rheological behavior of dense suspensions.

Jan 1, 1993

The mineral sands industry is oriented primarily toward the supply of titanium (Ti) raw materials (titanium feedstocks) for the production of titanium dioxide (TiO2) pigment and titanium metal. Titanium minerals ilmenite, rutile and leucoxene, and titanium slag and synthetic rutile are all used principally as feedstocks for the production of white TiO2 pigment. It accounts for almost 90 percent of the world?s consumption of titanium minerals. The remainder is used for the production of titanium metal, fluxes for welding rods and as a metallurgical flux in iron and steel making. Titanium dioxide pigment is produced by two alternative process routes, the sulfate process or chloride process. The bulk of the world?s titanium dioxide is derived from the mineral ilmenite, which also contains iron oxide and other minor impurities. At some mining operations, the iron present in ilmenite is removed (ilmenite beneficiation) to produce a high TiO2 feedstock (slag or synthetic rutile) typically containing between 80 percent and 95 percent TiO2. Pigment producers then further process it to produce pigment.

Jan 1, 2011

By Ralph C. Flow

In Cleveland County, North Carolina, one and one-half miles south of Kings Mountain, Foote Mineral Company operates an open pit for the production of spodumene, feldspar, mica, and commercial stone. Spodumene concentrate is sent to Footers Sunbright, Virginia plant and to other customers. Exton, Pennsylvania and New Johnsonville, Tennessee plants produce lithium compounds sold to the oil industry for multipurpose lithium-base greases, to the metal industry as welding flux, to the air conditioning market, and to the glass industry. Ceramic grade spodumene, feldspar, and mica concentrates go to other processing companies from the Kings Mountain plant. Waste amphibolite is delivered to a neighboring quarry operation.

Jan 1, 1962

By E. Yigit

Hydrometallurgical production of zinc from concentrates is generally carried out by H2SO4 leaching. For the smooth operation of this process, some harmful components must be removed from the leach solution before the electrolysis stage; MgO is one of these compounds. Zinc concentrate samples from the Mount Isa mines were used in leaching tests. Leaching tests with an aqueous solution of H2SO4 and SO2 gas were carried out at various temperatures, pH levels and leaching durations. While duration and the pH value of the solution were effective parameters in H2SO4 leaching, temperature and pH were more effective in SO2 leaching for the removal of MgCO3 and CaCO3. Removal of MgCO3 and CaCO3 was generally achieved at low pH values. The results show that SO2 gas can be a good alternative to sulfuric acid in the leaching of MgCO3 and CaCO3

Jan 1, 2010

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

By S. Garcia

The Minera Yanacocha operation presents various operating challenges, due to the complex structure of several heaps interconnected with ponds and gold recovery plants. A comprehensive process model has been developed in order to better understand the effects of certain operating parameters on issues such as water usage and inventory. An integral component of the water/mass balance of the process is a model of each heap that describes the flow and chemical behavior based on the individual characteristics of the heap. A computational fluid dynamic (CFD) software framework is used to model the individual heaps. The structure, calibration and validation of the model are described. Several examples demonstrating application of the process heap model are presented for the La Quinua heap. The effects of loss of solution flow to the heap (i.e., pump failure), increased cyanide levels in applied solutions and higher copper head grades on the process operation and balance are investigated with model simulations and compared to the baseline operating conditions. An example of estimating gold production and inventory based on projected heap loading plans is provided.

Jan 1, 2010

By D. Shink

A small scale continuous flotation cell was designed and constructed at Noranda Technology Centre to develop a mobile testing flotation circuit located next to the production circuit. This mobile small scale flotation pilot plant can easily and economically be set up at any circuit in a mill and used to evaluate and predict plant performance against a given flotation condition. The main feature of the cell, beside the provisions of automatic pulp level and feed rate control, is to provide a reduced surface to volume ratio approaching to that of an industrial machine. This paper describes the basic design and the results of various testwork carried out to date including aeration, conditioning, reagents, recirculation, flotation gas, etc. are presented in comparison with the plant production results.

Jan 1, 1992

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020