Search Documents

By J. Schoenbacher

Park City Municipal Corporation (PCMC), long before being recognized as an Olympic venue was known as one of the great American silver mining towns. During a century of active mining, the Park City mining district produced millions of ounces of silver in addition to a substantial amount of mine tailing waste. Since 1985 the City has been remediating these impacts with state and federal oversight. One particular challenging CERCLIS site, that was previously a historic mine tailings pond is known as Prospector Square Development (CERCLIS Listing Silver Creek Tailings UTD98051404). This site has been very challenging due to the metals that impact the shallow ground water that eventually drain into the Silver Creek Watershed. To address the water quality impairment the City and Missouri University of Science and Technology teamed up to investigate the feasibility of constructing a horizontal-flow wetland to treat this pollutant source. This effort began with the building of a pilot cell in June of 2004 and lead to the construction of a full scale horizontal-flow wetland in the fall of 2008. The design of the pilot and full scale biocell was based upon lab-scale research conducted by the Missouri University of Science and Technology. In October of 2008, the Prospector Drain effluent was introduced to the system and to date analytical results reveal that the biocell is treating the Prospector Drain outfall below the Silver Creek Total Maximum Daily Load (TMDL) endpoint goals for zinc .39 mg/L and cadmium .00075 mg/L. The water chemistry of the influent, that originates from the historic silver mine tailings pond, is impaired with zinc and cadmium and has low iron with a pH of roughly 6.5. The construction of this unit encountered many challenges related to constituent relations, regulatory scrutiny, constructability and start-up. Nonetheless, since implementation this unit is considered a success for improving water quality within the Silver Creek Watershed.

Jan 1, 2011

By M. G. Hester

The ore reserve modeling of stratiform uranium deposits to be mined by selective underground mining methods must be done with consideration of the erratic nature of the ore forming processes that produced the mineralization. Estimation methods that model the uranium grade as a smooth transition between high grade and low grade drillhole intercepts tend to greatly overestimate the ore tonnage. Care must be taken to first establish realistic ore pod geometries and then estimate the grade of the reserve units within the pods.

Jan 1, 1985

By J. S. Hall

The performance of a full-scale balling drum circuit is well known to fluctuate, and is difficult to control. The fluctuations stem from causes that are not readily quantifiable. Results from plant tests show that surging of the recycle tonnage is dependent, inter alia, on the method of bentonite addition, small variations in drum or cutter bar speed and the method of drum water addition. This paper presents detailed observations from experiments on full-scale drum circuits, including preliminary results of a computer measurement and control scheme. Size distributions measured at points along an industrial drum are presented, together with the results of a mathematical model fitted to one plant data set. Model predictions are also included emphasizing the importance of screen performance on circuit stability.

Jan 1, 1983

By Magnus Ericsson

The unexpectedly quick recovery in world crude steel production in the second half of 2009 was due almost entirely to increased production in China that began in late 2008. Previous peaks in monthly production in China were matched by April 2009. The rest of the world had still not reached pre-crisis production rates by May 2010. Chinese production drives growth, but there has been some growth in most other larger crude steel producing countries as well, compared to production in 2009. If the production rate of the first four months of 2010 continues, the total output of crude steel in 2010 will be somewhere around 1,410 Mt (1.5 billion st), the same as in the record year of 2007.

Jan 1, 2010

By W. R. Dengler

Dynatec Mining Limited contracted to sink a lS00 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.S ft.) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (l5 ft.) diameter double-drum hoist to sink the shaft with 12.S tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1992

By A. E. Torma

The efficiency of Thiobacillus ferrooxidans in the desulfurization of a high-sulfur content New Mexico coal was demonstrated. The optimum condition of process variables were found to be pH = 2.3, particle size = 38 µm, pulp density 14.1% (W/V) and temperature 33.9°C. Larger scale experiments carried out with these optimum conditions resulted in coal desulfurizations above 97%, while in sterile controls this was only about 10%.- The rate of desulfurization was described with an exponential expression with respect to the effects of coal particle size. The effect of pulp density on coal desulfurization was quantified by a Monod type equation. The apparent activation and deactivation energies, the frequency factor and temperature coefficient were derived from the effects of temperature to be ?aE - 11720 cal mol-1 and A = 30.44 mol dm-3s-lin the range of 20 - 35°C; ?Ed = 43930 cal mol-1 and A = 9.82 x 10-39 mol dm-3s-1 in the range of 35 - 45°C; and Q10 = 1.94 in the range of 20 - 30°C. The thermodynamic values [(?G+, ?H+ and ?S+)] of the activated complex were calculated. The generalized second order regression equation relating the degree of biodesulfurization of coal to the leach parameters was shown to adequately predict coal desulfurization within the range of process variables studied.

Jan 1, 1987

By Thiemo Hagedorn, Gerhard Weissbach, Ralph Bergmann, Wilhelm J. Kogelmann

The objective of this unique method is to multiply the advance rate of conventional tunneling while improving both ground control and the safety of the crew. The high advance rate is achieved by concurrent rock excavation and installation of concrete lining at fully synchronized work phases. The novel TACHUSMATIC system consists of a high-production, robotic cutter boom, an automated slip form and continuous mucking and conveying. This novel system utilizes the inherent bearing capacity of the rock that is activated by a small, initial deformation. The supporting resistance is then provided both by the rock mass itself and the pumped in concrete lining. During the hardening of the concrete, the hydraulic cylinders of the TACHUSMATIC automatically apply the appropriate support resistance, thus providing safe ground control. This novel tunneling system is practically a fully automated, fail-safe NATM that does not require highly skilled engineers and crew. The TACHUSMATIC can be used for construction of circular, rectangular and horseshoe-shaped tunnels. When equipped with the Alpine Multi-Tool Miner (MTM) systems, the machine can work in a wide range of ground and rock conditions. The use of novel, diamond-tipped cutter bits (picks) will increase hard rock cutting capabilities and will significantly reduce pick consumption. Because of its moderate cost, the novel system is an economic alternative to conventional tunneling even at short drivages. A new installation is cost-effective for tunnels longer than 750 meters (2,500 ft.) At a typical tunneling project, the cost permeter is about 25% lower than with conventional methods.

Jan 1, 2003

By Eugie Kabwe

The increase in depth of mines due to the depletion of surface deposits leads to unsafe tunnel construction and overall ore extraction. This is due to tunnel instability associated with the surrounding rock mass’s ability to exhibit creep that occurs over time. However, the explicit description of this mechanism using conventional constitutive models has proven to be difficult and inadequate. Hence, this paper presents an integrated viscoelastic viscoplastic visco-damage model with the Duvaut-Lions function. The presented model is calibrated by experimental data to determine the viscoelastic viscoplastic and visco-damage parameters. It is further implemented in a finite volume numerical code and verified on an experimental scale by numerical modeling of a cylindrical specimen. It describes the 3-phase creep mechanism perfectly as compared to the inbuilt conventional integer-order derivative model. Results from the conducted verification show that it can successfully be employed to describe the long-term behavior associated with the creep mechanism.

May 16, 2021

By V. Dentoni

The paper deals with the assessment of the visual impact generated by surface mining and quarrying. Previous research works proved the applicability of an indirect method based on the elaboration of digital images through which the extent of the visible altered area and the chromatic contrast with the surrounding environment is calculated. The resulting level of visual impact allows an objective comparison among different cases as far as the evaluation procedure is univocally defined. The article illustrates the application of the method to a number of selected quarries located within the Sardinian territory; different issues are discussed such as the choice of the viewpoints from which the pictures are taken, the influence of the distance from the quarry to the selected viewpoints, the light condition and the orientation of the quarry faces. Moreover, the visual impact level obtained from pictures taken at the same time with five digital cameras are compared in order to evaluate the contribution on the overall uncertainty.

Jan 1, 2008

By Jorgen Elbrond

The capacity calculation of complex transportation systems involving variable activity times such as encountered in the mining industry are often worked out by means of simulation, which reconstructs waiting times and cycle times. The queuing theory, which mathematically calculates waiting times, has been used mainly to describe the, phenomena. This is due partly to the difficulties encountered in modelling complex systems and partly to the difficulty of reconciling the required time distribution laws with the real phenomena by means of the queuing theory. It is, however, obvious that formulas for capacity calculations would be preferable to simulation procedures because of their higher calculation speed, shorter and more flexible programs and shorter programming work. The calculation procedure presented in this paper is composed of some rather simple models, which are based on the queuing theory, and on some probabilistic and some deterministic considerations. The models are supported by observations, and to some extent by simulations. It has been attempted to find all the components of the cycle time and to include them in a comprehensive model. It is the intention to demonstrate that even quite complex mine transportation systems can be treated by means of the queuing theory with the advantages mentionned above and, without sacrificing the precision of the estimates. The speed of calculation of a wide range of parameter combinations is such that the procedure can be used extensively by a project engineer in the search for optimal modifications of the entire transportation system.

Jan 1, 1979

By L. Sandbak

The TRJV Mine is located approximately 43 miles northeast of Winnemucca, along the east flank of the Osgood Mountains in the Potosi Mining District, Humboldt County, Northwest Nevada (see Figure 1). The Turquoise Ridge Mine is an underground mine, and is a 25% joint venture partner with Newmont Mining. The TRJV mine utilizes the underhand cut-and-fill mining method due to the relatively low rock quality in the ore zones and the relatively shallow dipping 25-45 degree ore body geometries. This paper defines a rehabilitation risk rating system (RRRS) for prioritizing rehabilitation of drifts damaged in the mining processes including long term development drifts providing access to the mining areas. The ultimate use is as a mine planning tool for the organized scheduling of rehab in a timely manner. A few case studies of the most needy rehab areas identified by the RRRS mapping system is presented, and the type of rehab completed design for these areas. Suggestions on improving the rehab risk mapping system include the use of support history and rock mass strength rating factors.

Feb 23, 2014

By Robert W. Yokom

As the search for new sources of energy and minerals leads to more remote areas of the country - and the world - the need to plan for adequate housing and community facilities for the construction and operations workforces and their families takes on an importance equal to the mining and processing facilities themselves. A corollary to the need for planning is the increasingly crucial need for development companies to devise effective strategies for dealing with the local communities impacted by these projects. Experience has amply demonstrated the high price to be paid for failure to learn this lesson, a price measured in lost productivity, confrontation with local communities, labor turnover, mental health and other social and eocnomic problems. In Sweetwater, Wyoming, a new industrial activity caused the population to double from 18,000 to 36,000 between 1970 and 1974. During that period industrial productivity fell 25 to 40 percent, cost overruns on the principal new industrial facility exceeded 33 percent, annual employee turnover rates climbed above 100 percent, the local mental health clinic workload increased nine times and complaints to the local law enforcement agency increased 60 percent.

Jan 1, 1981

By Solomon J. Salat

During the major expansion of the Inspiration smelter, which took place in 1973, the bulk material handling system underwent a matching expansion in order to move the required materials. Inspiration is the first smelter worldwide to employ electric smelting in conjunction with the use of Hoboken converters (1), (2). The installation includes a 51 -MVA electric furnace, five 4.25m (14-foot) diameter Hoboken converters, rotary dryer, bedding plant, acid plant, heat recovery steam plant, and gas and dust handling system. See Figure 1, Plot Plan. As of today, the 51-MVA electric furnace is the world's largest in the smelting of copper. Engineering design for the installation was per- formed by Treadwell Corporation of New York. The task of designing the conveyor system was complex because the system had to be installed while the smelter was operating and with minimum plant shutdowns, and it had to serve both the existing and the new smelter. Existing conveyors were redesigned where necessary and incorporated into the new conveyor system. See Figure 2, Flow Sheet. The system encompasses the handling of such diverse materials as wet and dry copper concentrates, cement copper, silica flux, cold dope, and concentrate and flue dust.

Jan 1, 1979

By George W. Bain

Deposits of metals in only slightly disturbed strata have been attributed to sedimentation processes contemporary with deposition of the strata. Recently this origin has been extended' to a greater variety' of deposits and local enrichment has been attributed to selective remobilization of metallic minerals in the host stratum. Effects attending metallization and deformation, and exact age' of the metallization are compiled to establish the sequence of events in ore deposit histories in order to clarify importance of remobilization within a formation relative to introduction from an outside source into an fav¬orable host. The pertinence respectively of deposit; origin and geometry to the work of the mining geologist is reviewed. Dwarf faunas in the Clinton iron ore, Tully pyrite bed and Rammelsberg deposit, indicate abnormal metal ions in the sedimentary environment. Slight¬ly disturbed strata are host rocks in the Swedish Kolm, Timna, Kupferschieffer, and White Pine deposit; the latter two have ore only in conjunction with tectonic structures.

Jan 1, 1966

By Meng Li, Hao Nie, Weitian Ding, Mamdouh Omran, Ying Li, Yao Ge, Yaowei Yu, Abourehab Hammam, Lei Zan

This study examines the isothermal and non-isothermal reduction behaviors of iron ore compacts in a pure hydrogen atmosphere and compares the results obtained during the reduction process by CO. The different phases accompanying the reduction reactions were identified using X-ray diffraction (XRD) and its morphology was microscopically examined. In isothermal experiments, temperature plays a significant role in the reduction process. At any given temperature, the reduction rate during the initial stages is higher than that during the final stages. The reduction rate in H2 atmosphere was faster than in CO gas. The comparison of activation energy values suggested that reduction with H2 is more efficient thanwith CO. At the same temperature, the time required to achieve a certain degree of reduction was lower when using H2 gas than CO atmosphere. In non-isothermal tests, the heating rate has a significant effect on the reduction rate and reduction extent. At the same heating rate, the degree of reduction was higher in H2 atmosphere than in CO gas. Based on experimental data, the parameters of reaction kinetics were deduced by application of model-free and model-fitting methods. The reduction in H2 atmosphere was controlled by nucleation model (Avrami-Erofeev model), while the CO reduction reaction was controlled by gas diffusion.

Sep 29, 2020

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese (Mn) ferroalloys are chiefly consumed in the steelmaking process as a deoxidizing agent or as an alloying element to produce high-quality steels. These alloys are typically produced in a submerged arc furnace using coke, fluxes and manganese ores of a specific manganese/Fe (Mn/Fe) ratio. Preferred-grade manganese ores should have Mn content greater than 46 percent and Mn/Fe content greater than 5 to produce commercial-grade, high-carbon ferromanganese [1]. Selective mining of high-grade Mn resources has created a scarcity of these resources, which is emerging as a major challenge for the manganese and steel industry. Manganese ore resources are mainly distributed in South Africa, with about 32 percent; Ukraine, with about 17 percent; Australia, with about 17 percent; and Brazil, India, China, Gabon and Mexico, with lesser amounts.

By S. A. McGhee

Introduction ASARCO's Ray Operations include an open-pit copper mine in the Mineral Creek Mining District of Pinel County. The district is located in east central Arizona, 132 km (82 miles) southeast of Phoenix, AZ, and 126 km (78 miles) north of Tucson, AZ. The mine lies 8 km (5 miles) north of the Gila River in Mineral Creek Valley, between the Tortilla Mountains to the west and the Dripping Springs Range to the east. The rich copper deposits of the Mineral Creek mining district were first noted by a US Army Officer in 1847. The Ray Copper Company was the first major operation in the area. The company was named after the Ray mining claim, which was one of the earliest recorded claims. After decades of sporadic and unsuccessful mining ventures, the Ray Consolidated Mining Company was formed in 1910. The company introduced one of the first successful block caving operations in the world. In 1933, the Kennecott Copper Corporation acquired the Ray Consolidated Mining Company and continued operation of the mine under the same name until 1943, when the property was renamed the Ray Mines Division of Kennecott. Underground mining continued until 1955, when the mine was converted to an open pit operation. In November 1986, ASARCO Inc. purchased the Ray Mines Division and related facilities from Kennecott. The purchase also included the Hayden concentrator and the Ray Smelter, located approximately 32 km (20 miles) from the Ray Mine. This paper summarizes the 54,400 tpd (60,000 stpd) in-pit crusher and overland-conveying system and the 24,200 tpd (30.000 stpd) copper SAG concentrator and tailings disposal system constructed at ASARCO's Ray Complex - Ray Operations. General description of facilities The Ray concentrator includes a sulfide SAG concentrator, a "relocatable" in-pit primary-crushing plant and overland-conveyor system, a concentrator tailings-disposal system and plant ancillary facilities, The major elements of the project include: • A relocatable Fuller-Traylor in-pit 1524-mm (60-in) x 2261-mm (89-in) primary gyratory crusher at the 442 m (1450 ft) mine elevation. The crushing plant has a nominal capacity of 54,400 tpd (60,000 stpd) of sulfide ore. • A 1524-mm (60-in) wide x 1253-m (4110-ft) long overland belt conveyor, which runs from the in-pit crushing facility to a transfer station serving both the Ray Concentrator and the existing Hayden concentrator railroad load-out facility. • A 1524-mm (60-in) wide x 152-m (500-ft) long stackerbelt conveyor, which delivers a nominal 27,200 tpd (30,000 stpd) of ore from the transfer station to a 23,600 t (26,000 st) live-capacity coarse-ore stockpile serving the Ray Concentrator. • A nominal 27,200-tpd (30,000-stpd) concentrator, including semiautogenous grinding, flotation, copper concentrate filtration and associated plant ancillary facilities. • A tailings disposal system. Flotation tailings are pumped from the Ray Concentrator to a 122-m (400-ft) diam. thickener, located 4.8 km (3 miles) southeast of the Ray Concentrator site. The thickener overflow is pumped to two 76.2-m (250-ft.) diam. concrete process-water reservoirs. The thickener underflow, at 45% solids, is pumped to a new tailings disposal site located at Elder Gulch. • An HDPE-lined temporary-containment area to collect material from Ray Concentrator plant upsets and local storm-water run-off from a 100-year, 24-hour rain event. •A reclaim-water system from the Elder Gulch tailing pond area to the Ray Concentrator. • A 610-mm (24-in.) diam. x 31.9-km (19.2 mile) long fresh-water pipeline from the Hayden fresh-water-well field system to the Ray Concentrator. The overall process design criteria for the new Ray Concentrator is based on a nominal throughput of 27,200 tpd (30,000 stpd) of ore at 90% plant availability. However, based on the maximum performance capacity of the installed grinding equipment, it may be possible to achieve a sustained operating level in excess of 36,300 tpd (40,000 stpd) when processing soft ores. The balance of this paper will cover the major process systems including:

Jan 1, 1995

By Chiranjibi Santi, Amit Kumar Gorai, VIVEK KUMAR HIMANSHU

Air overpressure (AOp) and peak particle velocity (PPV) are the most undesirable effects of blasting in mines. It is an urgent need to design a predictor model for AOp and PPV for universal applications to minimize environmental effects and damages that occur due to blasting. The present study attempts to design an artificial neural network (ANN) model for the prediction of AOp and PPV in different conditions. In this study, the blast design parameters (number of holes, depth of the blast hole, stemming length, spacing, burden, distance of vibration monitoring location from the blast site, charge weight per delay) of two active mines (coal and iron ore) are considered in four different conditions for training and testing of the model for the prediction of AOp and PPV. The model was trained and tested in four different combinations of data (trained using data of one mine and tested using data of another mine, trained and tested using data of coal mine, trained and tested using data of an iron ore mine, trained and tested using combined data of both the mines) for examining the applicability in different conditions. The results indicate that R2 values are ranged from 0.886 to 0.908 and 0.8728 to 0.8959, respectively, in the prediction of PPV and AOp. A comparative study of the performances of the developed model with the other empirical model is also demonstrated. For this, the site constants of different empirical models were estimated individually for both the mines. The study results indicated that the ANN model performs much better than all the empirical models. It can be inferred from the results that blast vibration cannot be accurately predicted only from charge per delay and distance from the blast hole. The ANN model was considered many other factors and thus can predict the vibration level more accurately.

Jul 30, 2021

By C. L. Emery

The geology and early history of the discovery of potash in Saskatchewan as described by Heber Cole (1) and R. V. Thompkins (2) has dealt with the distribution of the salt beds and their potash content. From the many bore holes through the Prairie Evaporites the outlines and contours of the series have been well established. The thickest section of the salt beds lies to the north of the "barren" area and forms a belt running easterly to a point west of Yorkton. The "barren" area is a region where the salt has been redissolved and the strata have slumped down, to fill the voids. This area is of interest from the standpoint of rock mechanics. The potash-rich beds extend both east and west of the region. mentioned and the top of the Prairie Evaporite is at a depth below 3200 feet from the surface near Saskatoon and dips southerly at an average rate of about five feet to ten feet per mile.

Jan 1, 1966

By O. M. Arafat, J. A. Finch

Since its development, the functional performance equation for ball milling (McIvor, 1988) has facilitated a new understanding of industrial circuit cause and effect relationships, leading to significant strides in operational performance. Success stories of this approach to plant circuit performance improvement are now too numerous to list. Finch and McIvor (circa 1986) also discovered that the functional performance mill grinding rate at the size of interest was the same cumulative grinding rate that is calculated from mill feed and discharge size distributions using a first-order rate equation. By calculating these cumulative grinding rates for all screen sizes, a complete ball mill model is generated (as used by Finch and Ramirez, 1981). Others in industry, Hinde and Kalala (2009), for example, have noted the same. Lacking the complexity needed to maintain their interest, most researchers have ignored this model, broadly opting instead for Epstein’s (1948) characterization of grinding as a chemical reaction, combining selection rate and breakage size distribution functions. The much simpler ball mill model has previously been incorporated into a proprietary circuit modeling program (McIvor, 2005) and used for plant improvement work (for example, see McIvor and Finch, 2007, and McIvor, 2014). Now, by combining this business-friendly ball mill model with optimization criteria from functional performance analysis, a circuit modeling system (including the needed supplementary steps to assure successful plant implementation of circuit design changes) is at the disposal of every plant metallurgist, grinding equipment/ material provider and circuit designer.

Jan 11, 2017