Search Documents

By S. Pal, A. K. Lahiri

Most of the compounds present in slag are surface active. This gives rise to foaminess of slag. The foam life and foaming index are normally determined by the draining rate of slag through the plateau border, so the foaming index is directly proportional to slag viscosity and inversely proportional to slag density and bubble diameter. When a small amount of a strong surface active compound like P2O5or Cr2O3is present in slag, however, the foam life increases significantly and the above relationship is not obeyed. The strong surface active compounds reduce the draining rate from the film between the adjacent bubbles so the film draining controls the life of the foam. The thickness of the film, Marangoni force, viscosity of the slag, and diffusion of surface active compounds determine the film draining rate. The interplay of these factors leads to very low or high film draining rates and affects the film and foam stability significantly. Keywords: slag, foam, foaming index, film draining

Jan 1, 2004

By D. R. Hack, N. M. Sirakov, M. L. Feves, M. Iwanowski

This paper presents a new approach capable of volume calculation of 3D reconstructed geological objects. The method is based on a well-known concept that states the volume of an object can be computed as the limit of the sum of the area of infinite number of sections, which cut the 3Dobject. Since shortage of input data about the geological objects usually exists, Mathematical Morphology and polynomial interpolation are employed to generate a set of intermediate sections between the set of initial sections. A Mathematical Morphology tool is applied to compute the area of the two of sets initial and generated 2D sections. Regularities together with Delaunay Triangulation are employed to perform 3D reconstruction. A formula is developed on purpose of volume calculation of the reconstructed objects. A set of ten theoretical, electrical resistivity cross-sections were generated and used to perform an experiment to show the capability of our approach to estimate the volume of complex 3D geological object in case of sparse 2D sections. The volume determined using the morphological approach presented in this paper show good correlation with the volume of the original input object. Advantages and disadvantages of our volume calculation approach are discussed in the conclusion of this paper. Keywords: electrical resistivity, sparse 2D sections, geological objects, smooth 3D visualization and volume calculation.

Jan 1, 2003

Experimental studies on viscosity of titanium bearing slags have been reviewed and the assessed data were used in extending the capability of the structurally related viscosity model for silicate melts, developed by the present authors. Experimental data on ternary and higher order systems containing CaO, MgO, MnO, FeO, Al2O3, TiO2, Ti2O3, SiO2were assessed and used. The newly extended viscosity model represented the viscosity behaviour over broad temperature and composition ranges. The structural role played by TiO2and Ti2O3in silicate network structure is discussed with respect to their effect on viscosity of melts. Keywords: viscosity model, TiOx containing silicate melts, silicate network structure.

Jan 1, 2004

By F. M. G. Egerton

Mechanisation of mining operations is not a new concept in the world of mining. Machinery has been developed, manufactured and used for many decades in massive orebodies and coal mines, both locally and abroad. Because of their size and the huge tonnages available, massive ore bodies lend themselves very easily to mechanisation. However, little progress in mechanisation has been made in narrow tabular orebodies in South Africa. The equipment available for narrow tabular orebodies requires excavations of a size that introduce large volumes of waste dilution. Nevertheless, it is essential for South African miners to experiment with mechanisation and to find a solution to the problem. This address looks at current conventional mining methods and compares them to bord-and-pillar type mining methods. Off-reef mechanisation is also touched on. It then looks at different hybridised mining methods that are being used, i.e. a mixture of conventional mining and mechanisation. It finally looks at future prospects for mechanisation in narrow tabular orebodies.

Jan 1, 2004

By J. M. Font, R. G. Reddy

Jan 1, 2004

By H. Hamma, R. Fehrmann, M. Gaune-Escard, G. Hatem, S. B. Rasmussen, K. M. Eriksen

The molten salts M2S2O7and MHSO4, the binary molten salt systems M2S2O7-MHSO4and the molten salt-gas systems M2S2O7-V2O5and M2S2O7-M2SO4-V2O5(M = Na, K, Rb, Cs) in O2, SO2and Ar atmospheres have been investigated by thermal methods like calorimetry, Differential Enthalpic Analysis (DEA) and Differential Scanning Calorimetry (DSC). Fundamental thermodynamic data like temperatures and molar heats of solid-solid transition and fusion, phase diagrams, heat capacities of solids and liquids, heat of mixing, and heats of complex formation have been obtained and are reviewed here. Also EPR spectroscopic evidence of V(IV) complexes and their structure are reported and the results are discussed in relation to the mechanism of SO2oxidation by V2O5based industrial catalysts. Keywords: Alkali pyrosulfates, alkali hydrogen sulfates, vanadium pentoxide, EPR spectroscopy, complex formation

Jan 1, 2004

By R. T. Jones

Slags have been produced as by-products from pyrometallurgical processes for thousands of years, and have generally been regarded as waste. Many of these slags are no longer seen as residues merely to be discarded, but as potential economic sources of metals, or as useful by-products in their own right. Slag cleaning can enhance the recovery of valuable metals in existing pyrometallurgical processes, or can produce economic value from recycling old slag dumps. For example, a process has been developed and implemented industrially for recovering cobalt from copper smelting slag in a DC arc furnace. The relatively non-leachable behaviour of glassy slags allows them to be used as a very safe means of disposal of metallurgical waste streams, including many that are classified as hazardous. The high temperatures, reducing conditions, and good mixing that can be achieved in a DC arc furnace enable the effective functioning of this environmentally beneficial means of disposal. Lead blast furnace slag can be rendered safe for disposal by treating it using the Enviroplas process, which strips most of the hazardous lead from the slag (and traps the rest in an insoluble glassy slag) and recovers economic quantities of zinc by absorbing (in a lead splash condenser)the zinc vapour that is fumed off in the furnace. Another example can be seen in the recovery of a chromium- and nickel-containing alloy from stainless steel plant dust, while producing a disposable residual slag. The examples presented here illustrate that it is possible to develop processes that are both economic and environmentally beneficial. Keywords: DC arc furnace, plasma, slag cleaning, cobalt recovery, zinc fuming, Enviroplas, jigging, re-melting fines, environmental, economic

Jan 1, 2004

By H. Urata, K. Ishii

To determine the effect of F ions in the molten alkali silicate systems on their structures, quenched Na2O-SiO2-NaF systems were investigated by Raman spectroscopy and molecular dynamics simulation. The systematic increase of 1100 cm-1band intensity in the Raman spectra of the silicate melts accompanying the replacement of F for O provides the evidence for concomitant polymerization of melts. From the molecular dynamics simulation, it was confirmed that most of substituted F was mainly coordinated to Na+ ions but not Si4+ions. These results were consistent with the mechanism in which F associated with otherwise network-modifying Na rather than with network-forming Si. Since F was associated to Na+ ions, the replace of O ion by two F ions promote the polymerization of silicate melts. Keywords: fluorine; molten flux; slag structure; molecular dynamics simulation; Raman spectroscopy.

Jan 1, 2004

By E. Chen, M. Barati, K. Coley

The reaction between carbon and slags is of significant importance in direct smelting of iron ores, EAF slag foaming and copper slag cleaning processes. This reaction is known to occur via gaseous intermediates and it is important to have fundamental data to understand the relative importance of each reaction step. In this study, the rate of CO2dissociation on different slag surfaces is measured using an isotope exchange technique. It was found that increasing iron oxide content up to 30 wt per cent does not have a significant effect on the rate constant while increasing from this limit, increases the rate constant dramatically. Activation energy of CO2dissociation on slags of unit basicity and different iron oxide contents is in the range of 180±40 kJ/mol. It is found that rate constant dependence on oxygen potential in the slag phase is increasing with iron oxide concentration. In the case of copper making slags, the influence of copper oxide is found to increase the magnitude of apparent rate constant, while decreasing the activation energy considerably. Key words: Gas-slag reaction, CO2dissociation, copper slag, kinetics, isotope exchange

Jan 1, 2004

By P. Gonzalez, C. Ariyo, L. Holappa

Oxidation state of titanium was determined in CaO-SiO2-TiOxslags in the composition range25–53 per cent CaO, 27–46 per cent SiO2, 10–55 per cent TiOxat 1873K using gas equilibration method. In the experiments, slags with different titanium oxide contents were equilibrated with a known carbon monoxide and carbon dioxide ratio. The results were used to determine the Ti3+and Ti4+contents as well as the activity coefficient ratio of corresponding oxides in the slag. The dependency of the activity coefficient ratio as a function of oxygen partial pressure was determined. Keywords: titanium, titanium oxide, activity, activity coefficient, slag iron, carbon monoxide,carbon doixide, gas, equilibrium.

Jan 1, 2004

In ilmenite smelting, the FeO content of the feed material (nominally FeO.TiO2) is decreased by reduction with carbon. In a parallel reaction, a significant amount of the TiO2is reduced to Ti2O3.One of the striking features of these reactions is a consistent relationship between the extents of FeO and TiO2reduction; this relationship is independent of furnace size. It was recently proposed that this relationship follows from the solidification behaviour of the slag, where the final slag composition corresponds to the minimum melting point (?eutectic groove?) in the FeO-TiO2-Ti2O3phase system; the hypothesis is that solidification equilibrium with the freeze lining stabilizes the slag composition. If this is the case, the system of slag and freeze lining must be capable of correcting two types of disturbances: thermal and compositional. Thermal disturbances result from incorrect power input, for the feed rates of ilmenite and reductant. For example, excessive power input will tend to overheat the slag, causing the freeze lining to melt partially, establishing a new steady-state heat loss from the furnace. Compositional disturbances result from an incorrect reductant input for the given power and ilmenite input. In this work, the dynamic response of the slag and freeze lining to different inputs (flow rates of ilmenite and reductant, and power input) is modelled. The model is based on solidification equilibria, and quantified heat loss through the freeze lining. The conclusion is that the solidification equilibrium cannot constrain the composition to the eutectic groove for typical operating conditions. Keywords: ilmenite smelting, freeze lining, solidification, high-titanium slag

Jan 1, 2004

The distribution of chrome spinels in a magnetically fractionated ilmenite concentrate sourced from the Murray Basin was characterized by XRF assaying, quantitative electron microprobeanalysis, grain mapping, automated mineral phase clustering, and modal analysis. At least 14 distinct chrome spinel types were present in the concentrate. There is considerable variation in the amount of each chrome spinel type present, although a high-Mg, high-Al phase makes up close to 45 per cent of the total spinel population. Magnetic fractionation results showed significant variation in the composition and relative abundance of spinels reporting to each fraction. Low magnetic field strength fractions (ie. high susceptibility grains) were dominated by chrome spinels that are mid-range in Al and Cr. These spinels have the highest magnetite, ulvospinel and Fe(Al,Cr)2O4components. In comparison, the high field strength fractions (i.e. low susceptibility grains) have the majority of the grains with high-Al contents indicating a higher proportion of Mg(Al,Cr)2O4component. Spinels high in a (Al,Cr)2.67O4non-stoichiometriccomponent are absent at low field strengths but tend to be concentrated in the high field strength, non-magnetic fractions. Intermediate field strength fractions tend to exhibit a broad spread in spinel compositional types. A mild roast treatment of the sample had no clear effect on the distribution of chrome spinels between different magnetic fractions, but it did cause a change in the magnetic properties of the accompanying ilmenite grains. The effect of more extreme roasting conditions on the magnetic properties of the chrome spinels is to be determined.

Jan 1, 2003

By S. Witzke, J. Lehmann, H. Gaye

The modelling work presented here concerns Ni-bearing steels produced by Imphy Ugine Précision. In such grades, the contents of elements such as silicon or titanium must be precisely controlled by slag/metal treatments. The slag phase is described by IRSID slag model that has been slightly revised in order to better fit recent SiO2activity measurements in the low SiO2content domain of the CaO-Al2O3-CaO system. The metallic alloys are described by the unified interaction parameter model (UIPM). In this formalism, the interaction coefficients, giving the effect of nickel on Al, Si, Mn and Ti activities, have been determined by electrochemical measurements and/or extracted from industrial data on slag/metal treatments concerning a wide range of alloy compositions: [ ] Keywords: slag, Ni alloyed steels, activities, interaction coefficient

Jan 1, 2004

By J. Lehmann, H. Gaye

A brief review of Computational Thermodynamics software concerning the modeling and prediction of reactions involving metals, slags and fluxes is presented. Their application for various steelmaking treatments is discussed. Examples concern phosphorus removal in BOF and EAF, ladle steel desulfurization, and specific treatments for inclusions control in semi-killed or Al-killed carbon and stainless steels.

By T. Tamura

It is known that the CaO-FetO-P2O5slag system has a wide liquid miscibility gap at steelmaking temperatures and this two-liquid slag phase has many advantages such as high activities of both FetO and CaO and high amount of P2O5. The phosphorus distribution ratio between the two-liquid slag and molten steel was confirmed to be higher than that between CaOsat.-FetO-P2O5slag and molten steel. The two-liquid slag may be useful for dephosphorization of molten steel and reduction of slag volume. Furthermore, the phase equilibrium of two-liquid CaO-FetO-P2O5slagsaturated with MgO was measured to determine the applicability of the two-liquid slag to dephosphorization in steelmaking process. Keywords: slag, refractories, solid solution, two-liquid phase, dephosphorization, steelmaking, phase equilibrium.

Jan 1, 2004

By E. T. Boshoff

Paper written on project work carried out in partial fulfilment of B. Eng. (Metallurgical Engineering) The weathering of kimberlite can be accelerated with cations in solution if swelling of the kimberlite occurs in contact with the weathering medium. The type and amount of swelling clays present, along with the surface charge and cation valence, determine the degree of swelling that can occur. Crystalline swelling occurs by the incorporation of cations in the interlayer spacing of the silica sheets. Kimberlite exposed to cupric cations showed very strong weathering, indicating that this type of weathering may be considered a viable process option. Kimberlite fines generated after weathering with monovalent cations showed poor settling behaviour compared to kimberlite weathered with di-, and trivalent cations.

Jan 1, 2005

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

By D Reddy

Rosh Pinah Zinc Corporation is a zinc-lead mine located in southern of Namibia. It is currently considering the development of a low grade ore body containing about 2.8% zinc. This ore can be utilised by the concentrator if it could be upgraded prior to the ball mill. Preliminary work indicated that the ore may be upgraded in a pre-beneficiating stage by using dense medium separation, X-ray sorting or a combination thereof to a feed grade of minimum 9% zinc. This paper describes the process followed in evaluating the technologies for pre-beneficiation. The results from test work indicated that the low grade ore is amenable to pre-beneficiation by both dense medium separation and X-ray sorting. A comparison between the two technologies showed that dense medium separation marginally outperformed X-ray sorting on grade and recovery. The results for the X-ray sorting were achieved by tuning the calibration curve specifically for the samples tested.

Jan 1, 2008

By G. J. van Tonder

The use of Molecular Recognition Technology (MRT), a highly selective separation technology using specifically designed ligands (such as macrocycles), has been demonstrated to be an effective treatment process for removal of several ions that are commonly found in many hydrometallurgical circuits as well as in environ-mental treatment operations. Ions removed by MRT include base, heavy and transition metals, precious metals, halides, and alkali/alkaline earths. A MRT pilot plant run was conducted at Zincor to demonstrate the cobalt/nickel purification of zinc electrolyte, and to recover saleable pure cobalt/nickel sulphate solution. The MRT process holds various advantages, which include the elimination of a catalyst such as arsenic trioxide, conventionally used in cobalt and nickel cementation. SuperLig® 138 can be used to remove cobalt and nickel from120?170 g/l Zn-solutions at pH 1?2. The Zincor MRT application demonstrated its capability of concentrating large volumes o copper barren impure solution at low cobalt and nickel concentration levels in the feed, to small solution volumes at high cobalt and nickel concentrations. Around 99.5% of the cobalt was removed from solution with cobalt impurity levels in feed varying between 10 mg/l and 26 mg/l.

Jan 1, 2002

By O. I. Ostrovski, D. K. Belashchenko

The aim of this paper is the construction of models of systems with ionic and ionic-covalent bonds (molten salts) using experimental diffraction data and the calculation of their structure and thermodynamic and transport properties. Modelling was performed using algorithm BELION, in which the non-coulomb part of interaction potential between ions in the model was determined by the method of iterative simulation which targeted agreement between calculated and experimental partial pair correlation functions (PPCFs). The ionic charges in salts, which can be fractional, were determined by minimization of internal energy. In this paper, the algorithm BELION is applied for chlorides of alkaline-earth metals. Pair potentials, PPCFs, atomization energies, self-diffusion coefficients and electric conductivity are calculated. The charge of alkaline-earth metals was in the range of 2.0-2.1, slightly increasing from Mg to Ba. Partial pair correlation functions and atomization energies of models agree well with experimental data for MgCl2, SrCl2and BaCl2. Keywords: molten salt, molecular dynamics, partial pair correlation function, ionic charge, atomization energy, diffusion.

Jan 1, 2004