Search Documents

By C. R. Speers

The induced elastic stresses in the sidewalls of gold-mining tunnels at a depth of 4000 m in the Witwatersrand exceed the peak compressive strength of even the best-quality quartzite rocks. Laboratory tests measuring post-yield stress versus strain response show that brittle fracture occurs, followed by a loss in strength associated with strain-softening behaviour. Numerical modeling based on an assumed Mohr-Coulomb criterion fitted to the test results shows that large ongoing deformations of the sidewall occur, leading to total tunnel failure without adequate support. A methodology is presented to enable a quick assessment to be made of support requirements in terms of ground characteristic curves for numerically derived pressure versus displacement. From these curves, estimates can be made of the force levels for cable bolting and of the thickness and strength requirements for shotcrete linings. As an example of its application, the methodology is used in a comparison of the relative stability efficiencies of a square-shaped tunnel and a horizontal ellipse-shaped tunnel.

Jan 1, 1996

By K. Levin, P. Lloyd

During the commissioning phase, which is usually the most exciting part of a project involving the design and construction of metallurgical plant, the commissioning engineers interact between the client and the project management. The client wants to see whether all the equipment that he has bought and that, in his opinion, has taken far too long to erect will actually work. Project management expects the commissioning people to con¬vince the client that this is the best design ever developed and that never before have time and money been spent so well. The commissioning team has to fulfil these expectations. Commissioning work is a `shirt sleeve' function, with little of the glamour that is normally associated with fields such as engineering and operations. The team usually works in a partially completed plant with more temporary than permanent services and little (if any) office accommodation, normal working hours do not apply, and the demands made on the team change suddenly and dramatically. This article outlines the activities of the commissioning group and the systems used to smooth the commissioning path.

Jan 1, 1981

By D. J. Bosman

The impoved densification of sludge from neutralized acid mine drainage. by D. J. BOSMAN, B.Sc., (Member) The paper describes an investigation aimed at finding a solution to the accumulation of acid mine drainage in the old workings at Coronation Collieries, Kromdraai. The problem involved the neutralization of the acid in the water, without the large volumes of sludge and the large amounts of dissolved solids that usually result from neutralization. Pilot-plant work on the site using a limeneutralization process developed at Bethlehem Steel Corporation (U.S.A.) showed this to be a feasible method. A sludge of 22 per cent density was obtained under optimum operating parameters. The amount of suspended solids in the overflow water was very high, but this does not give rise to concern because the full-scale plant at Kromdraai will practise secondary sedimentation by running the thickener overflow through large dams with a theoretical retention time of 25 days. An analysis of the theory underlying the process is also made.

Jan 4, 1974

By J. A. L. Napier

An analytical solution to the best choice of cutoff grade for a mine is deduced for an assumed model of selective mining. It is found that this choice is determined by the constancy of a special function, the Hamiltonian, over the life of the mine. It is suggested that the appropriate constant value for this function should be determined by the expected long-term average of the paylimit. In that case, the optimum profile can be calculated at each point in time according to the prevailing working cost and product price. In particular, a decision can be made between operation at the true paylimit or at the subsidized paylimit implied by either the lease and tax formulas or the assistance formula for gold mines. It is also shown how the basic formulation can be extended for 'use in the determination of the optimum joint paylimit for two products over the life of the mine.

Jan 1, 1983

By J. R. de Wet

The behaviour of mild steel in aqueous cyanide solutions similar to caustic cyanide elution solutions was investigated at high temperature in electrochemical experiments. The anodic polarization diagrams of mild steel indicated that steel may undergo active dissolution under these conditions. The rare occurrence of gold plating in practice is the result of the limiting of the anodic dissolution of the steel by the presence of a passive layer on the steel. This passive layer is stable only in a certain potential range, and the free corrosion potential attained determines whether the steel will be passive or active. For conditions typical of elution columns, several corrosion potentials are possible, depending primarily on the initial condition of the steel and the concentration of oxygen in the solution. If these conditions result in the formation of a passive layer on the steel, changes in concentration and temperature will not necessarily result in plating since the layer may exist in a metastable form.

Jan 1, 1993

By M. T. G. Davis, J. V. Cleasby, H. J. Wright

Mining practice in the Kimberley Division of De Beers Consolidated Mines Limited by J. V. CLEASBY. B.Sc.. A.R.S.M. (Fellow). H. J. WRIGHT. B.Se.. M.Sc.. (Fellow). And M. T. G. DAVIES. B.Sc. (Visitor) T his paper highlights the changes that are taking place at De Beers Consolidated Mines Limited in mining methods, mechanization, and employment practices. De Beers has four underground mines in Kimberley itself (Dutoitspan, Bultfontein, De Beers, and Wesselton), and two open-cast mines outside Kimberley (Finsch and Koffiefontein). Emphasis is placed on the new method envisaged for Koffiefontein when it becomes an underground mine. The paper also includes notes on chemical drilling and on winding practices.

Jan 12, 1975

By R. J. Davidson

The mechanism of gold adsorption on activated charcoal by R. J. DAVIDSON: M.Se., Ph.D. (Rhodes) (Visitor) The adsorption of gold onto activated charcoal is most dependent on the concentration and character of the 'spectator' cations present in the adsorption medium. In the presence of calcium ions, gold is adsorbed as the calcium aurocyanide complex. The degree to which the aurocyanide complexes are adsorbed follows the series Ca> Mt:> H> Li> Na> K, calcium aurocyanide being the most stable complex and potassium aurocyanide the least firmly bound. If a loaded charcoal, where the gold is present as the calcium complex, is treated initially with either sodium carbonate or potassium carbonate solutions, the gold can subsequently be eluted from the charcoal with hot deionized water as either the sodium or the potassium complex respectively. The elution of gold with deionized water appears to be most attractive practically and economically, and has several potential applications in the recovery of gold from dilute solutions.

Jan 10, 1974

By L. A. Cornish, B. Eatwell

Austempered ductile iron (ADI) is a ductile iron which has had its matrix toughened by an austempering process. The alloy exhibits remarkable properties, which it owes to a unique microstructure comprising graphite nodules embedded in a matrix of acicular ferrite and carbon-enriched austenite. The properties include high strength combined with high toughness and ductility. Excellent wear resistance is also exhibited because, under strain, the austenite is transformed locally to martensite. Samples of ductile iron were austempered to produce grades I and IV AD!, and were tested at various strain rates. The grade IV ADI exhibited higher strengths and lower difficulties, and the strengths were found to be more dependent on strain rate. Transformation to martensite was more prevalent at the lower strain rates. A mechanism of increased flow stress and work hardening in the austenite of the matrix is proposed to explain the higher strength of the samples at high strain rates, where significantly less martensite is formed in the matrix.

Jan 1, 1995

By H. S. Sichel

Statistical valuation of diamondiferous deposits By H. S. SICHEL, D.Sc The valuation of diamondiferous deposits depends on (i) the density distribution, (ii) the size distribution of stones and (iii) the selling price structure prevailing at a particular time. In the density distribution the stochastic variable is defined as the number of individual stones found per sample unit irrespective of the stone size. The density distribution is discrete and allows for barren sample units. As diamonds often occur in clusters, a Poisson mixture distribution is derived which is entirely new, as existing discrete distributions cannot represent the stone number frequencies found in nature. For the sizes of diamonds, which are measured by weight, a new compound logarithmic normal distribution is developed. Combination of (i), (il) and (iii) leads to a meaningful appraisal of diamondiferous ground expressed in monetary value per production unit of mining. Finally, confidence limits are calculated which allow for inferences from sampling to recovery.

By A. A. Snodgaass

This paper reviews lead as a commodity, starting with a brief historical outline and dealing with the various uses of lead in some detail. It then goes on to discuss some statistics in relation to the production and reserves of lead, before sketching its mode of occurence. The topics are approached in regard both to the world and to South Africa, with the emphasis on the later. The mining and concentration of lead at Black Mountain Mine at Aggeneys in the north-western Cape Province are detailed, before a general account is given of the smelting, hydrometalurgical extraction, and refining of lead, together with the processes used in these activities. The paper concludes with a discussion of safety and health in regard to lead and a brief look at the commodity's future.

Jan 1, 1986

By W. A. Lenhardt

During the past five years, several research projects on the causes of mining induced seismicity have been carried out by the Rockburst Research Department at Western Deep levels Limited. This paper summarizes the results of these investigations. Several types of mining-induced seismic events are addressed, and models of their mechanisms are presented. It is shown that most of the seismicity results from mining in geologically disturbed areas, and ways and means are discussed to reduce the seismic potential. Stabilizing pillars, for instance, have been introduced to reduce stresses at the stope face and to alleviate the facebursting problem. Facebursts still occur in areas of very low stresses, and pillars became the source of very large seismic events (M >3). At this stage, the understanding gained of pillar-associated events allows a review of current mining practices. Further, it makes possible an examination of the efficiency of measures to alleviate the effects of various seismically prone situations.

Jan 1, 1992

By Y. Zhen, N. Topliffe, G. Shou

The typical service life for a long distance slurry pipeline is15 to 25 years. Determination of wear rate for a pipeline could have a high economic impact on the pipeline project. Wear is a combination of chemical corrosion and mechanical abrasion. The contribution of each factor has to be determined project by project. Normally, chemical corrosion dominates the pipe wear in fine slurry pipelines. These pipelines have been designed with a velocity between 1.5 m/s and 2.5 m/s. Solids are suspended with high homogeneity across the pipeline section. Bottom wear is not much greater than the top wear and not sensitive to velocity. The wear pattern in the pipeline transporting medium coarse solids, such as milled ore and tailings, is different. Wear concentrates on the bottom of pipeline and the outer bends, and is more sensitive to flow velocity. Wear distribution along the pipelines is similar.

Jan 1, 2007

By Siemag Transplan GmbH

At the Hansa Mine in Dortmund, Germany, coarse run-of-mine coal, up to 60 mm in particle size, has been brought to the surface hydraulically from a depth of 850 m since November 1977. Hoisting is done by a three-chamber pipefeeder, by means of which up to 400 t/h can be lifted. The pipefeeder operates without problems, and has so far shown itself to be efficient and reliable. Vertical hoisting can be carried out by water supplied from the surface, from underground, or from a surface water supply in combination with minewater from underground. Water that flows into the mine, which would in any event have to be pumped to the surface, can be utilized for hoisting operations. The energy costs per ton of coal for a lifting height of 850 m vary between 41 and 62 South African cents, and therefore lie within the range of costs that apply to conventional hoisting.

Jan 1, 1980

By M. H. Moys

Accurate models of mill power are becoming more necessary as the design, operational, and control requirements for grinding mills become more stringent. Models of mill power are reviewed briefly, and a new semi-phenomenological model is derived. The conventional torque-arm model for mill power is combined with a model of the tendency of the load in a mill to centrifuge at high speeds, to describe mill power that can be related to several design variables (such as mil geometry, mill speed, and liner design) and control variables (such as load volume, slurry rheology, and mill speed in the case of variable-speed milling). The semiphenomenological nature of the model allows rational conclusions to be reached concerning the effect of various aspects of mill-load behaviour on mill power. The model is shown to be capable of describing reality with much greater accuracy than is achieved by empirical models such as the Bond model.

Jan 1, 1993

By R. M. Falcon

The paper opens with a summary of the major factors responsible for spontaneous combustion in coal discards. These include heat arising from the oxidation of coal and pyrite, and from the weting of dry or oxidized coal and pyrite; and certain petrographic conditions leading to self-ignition of the coal such as low rank, the presence of a high proportion of reactive constituents, and the occurence of highly porous and botanicaly structured inertinite macerals, The analyses of 6 samples from 2 discard dumps in the Witbank coalfield are included, which show that, according to a three-grade classification of liability to spontaneous combustion, one dump is 'reasonably liable' and the other is 'most liable', It is pointed out that factors other than liability to self-ignition determine the possible utilization of such discards, and that the prevention of oxidation is of great importance if they are to be utilized and spontaneous combustion to be prevented,

Jan 1, 1986

By G. Gafner

The paper gives the reasons for the development of a gold alloy of 990 fineness with good colour, durability, and mechanical properties, and explains why titanium was chosen as the alloying metal. Methods are described for the alloy?s production, solutionizing, and age-hardening. Mechanical properties are given as a function of deformation, age-hardening time, and temperature for three different starting states, and these properties are compared with those of some standard 14 and 18 ct jewelery alloys and pure gold. The effects of various salts and fluxes on the composition of the alloy after heat treatment at 1150, 800, and 500°C are discussed. These indicate how alloy scrap can be refined to pure gold, and how solutionizing and agehardening can be conducted without the use of vacuum equipment. The results of wear tests indicate that the alloy is more durable than normal coinage and jewelery alloys. Tips are given on the grain refining, soldering, and casting of the alloy.

Jan 1, 1989

By L. A. Vermeulen

Electronic circuits were developed and successfully utilized to record, store, and continuously transmit to a remote station physical information relating to the impacts of pebbles on the shell liners of an industrial pebble mill, and of electrical conduction in the mineral pulp. The information was obtained by the instrumentation of some of the bolts that are used to clamp the liner blocks and litter bars to the mill shell. The features associated with the impact and conduction signals have been interpreted, and it is shown that such signals can lead to continuous measurements of the volume of the load in an industrial mill. Information is given regarding the angular distribution of direct impacts of the pebbles onto the shell liners, the power required to promote impacts, the amount of material in flight, the impact velocity, and the average number of direct impacts with the shell liner that any given pebble undergoes in unit time in the given mill.

Jan 1, 1984

1. Book review Respiratory protection - principles and applications by B. Ballantyne and P. H. Schwa be (Editors). London, Chapman Hall, 1981. (Reviewer: M. J. Martinson) 2. New manual Swedish steel manual, 1981. Available from Jernkontoret, P.O. Box 1721, S-I11 87 Stockholm, Sweden. SEK 85. 3. Publications of the Mineral Policy and Energy Sectors, Canada General review by L. Tibbo. 10 pp. Columbium (niobium) and tantalum by D. G. Fong. 6 pp. Sulphur by B. W. Boyd. 13 pp. Statistical summary of the mineral industry in Canada. 66 tables. Uranium by R. M. Williams. 16 pp. 4. Mintek reports Report 2126 The determination, by microwave techniques, of the interface between pulp and froth. Report 2129 An electrode controller for submerged-arc furnaces. Report 2131 The separation of trace elements in manganese dioxide. Report 2132 The assessment of pellicular anion-exchange resins for the determination of anions by ion chromatography. Report M2 The preparation of two reference materials of South African fluorspar. Report M3 The platinum-group minerals in the UG-2 Layer of the Bushveld Complex at Maandagshoek 254KT.

Jan 1, 1982

1. Book review • World mineral statistics 1974 to 1978. Production: Exports: Imports. London, H.M.S.O., Institute of Geological Sciences, 1980. (Reviewer: R. P. King) This edition is the third in a regular series prepared by the Institute of Geological Sciences. It is a useful compilation of statistics on the production, export, and import of fifty-eight different mineral commodities. Each mineral is listed by country, and a table is provided for the annual production, the annual imports, and the annual exports for each commodity included. However, some commodities are treated in considerably more detail; for example, aluminium and bauxite have tables under the following headings: Production of Bauxite, Production of Alumina, Production of Primary Aluminium, Exports of Bauxite, Alumina and Aluminium, Imports of Bauxite, Alumina and Aluminium. The information presented is the latest official information available from primary sources; the compilers have not relied on data from secondary compilations. This publication will be of considerable assistance to all who are concerned with the trading of mineral commodities and their production.

Jan 1, 1981

By H. M. Friede

Notes on the composition of pre- European copper and copper-alloy artefacts from the Transvaal by H. M. Friede. Ph.D. (Visitor) Seven copper artefacts (five ingots and two ornaments) found at prehistoric sites in the Transvaal were submitted to analysis. All the artefacts showed a high copper content and a relatively Iow level of impurities. A little-known ingot type from the Limpopo Valley ('nail' ingot) is described, and its analysis is given. The analysis of two copper ornaments that come from sites dated to the 5th Century AD. and the 11th Century AD. showed the constancy of the composition of copper articles over long periods. The well-known 'Blaauwberg Ingot' was re-analysed, and the results showed that this ingot cannot be regarded as a true bronze. Analytical values for the composition of three brass artefacts from Bambandyanalo (Mapungubwe), Northern Transvaal, are given. Some aspects of pre-European bronze manufacture and brass smelting, and of early metal trade from the East Coast into the interior of South Africa, are discussed.

Jan 2, 1975