Search Documents

By S. Mohanty, K. Sarangi, S. Dash, P. P. Patra

Industrial effluent from various industries contains heavy metals that are a serious threat to humans, flora and fauna in water bodies, and the environment. The heavy metals are dumped after precipitation, which has serious environmental consequences. In this paper, a 2D axi-symmetry CFD model has been developed to study the extraction of chromium ion from industrial effluent, in a hollow fibre membrane, using Alamine 336 as the carrier and kerosene as the diluent. The Navier Stokes equation was used to predict the velocity profile of the aqueous and organic phases, and species transport equation, which considers both convective and diffusive mass transfer, was used to predict the concentration profile of the chromium ion in the computational domain. The distribution coefficient was experimentally determined at a pH 4, which was found to be the optimum pH. Numerical simulations were performed considering 11.11 mol/m3 of initial feed concentration for chromium ions and extractant concentration of 0.2 M. Simulations were carried out with various aqueous and organic flow rates, and validated with experimental data. Keywords: CFD, metal extraction, hollow fibre membrane, heavy metals

Jan 1, 2020

By L. G. Austin

The paper summarizes the current state of development of simulation models for SAG and FAG mills, and gives the results of recent investigations of the physical processes occurring in autogenous grinding. The breakage process is treated as the sum of three regions of breakage actions: normal breakage caused by nipping of particles between media (steel balls or pebbles); abnormal breakage caused by media when the particle or lump is too big in relation to the media to be readily nipped; and self-breakage resulting from the chip¬ping fracture and abrasion of the tumbling action of rock lumps. Each region of breakage action has associated specific rates of breakage and primary progeny fragment distributions. A simplified form of the model was used to predict the performance of an 8 m diameter SAG mill with L/D = 0.5 grinding a copper ore, and predicted maximum capacity and minimum kWh/ton at about 6% ball load at 25% total filling. Two FAG mills of L/D = 2 were necessary to give the same capacity, and the simulations indicated a lower kWh/ton for these mills. For this ore, both systems were technically feasible.

Jan 1, 1987

By A. García-Gutiérrez, A. Aragón-Jerónimo, R. Salazar-Mendoza

A theoretical analysis of a two-region solid-liquid flow system in horizontal pipes is presented, which considers a stationary bed of drill cuttings as a porous medium (-region) below of a two-phase dispersed flow (-region).The method of volume averaging was applied in this study to derive a rigorous mathematical model in which each variable is precisely defined. This model includes the volume-averaged transport equations for both the two-phase dispersed flow and the porous medium regions and terms from a macroscopic forces balance. The solution of the two-region model allowed evaluation of the behaviour of pressure gradient as a function of velocity, total volume fraction of cuttings and the relationship of the height of the stationary bed and pipe diameter. The solution is based on a backward finite difference explicit scheme. The simulated physical system is a pipe of 4.135 m in horizontal length and 0.0508 m in diameter. A one-dimensional, mesh-centred grid, consisting of 100 nodes, is used. The numerical results were compared with experimental data on slurry flows and a good agreement was found. Keywords: two-phase, cuttings transport, solid-liquid flow, drilling modelling, volume averaging.

Jan 1, 2007

Book new a Book reviews Economics of the mineral industries. 4th Edition. Society of Mining Engineers (Caler No. D, Litleton, CO 80127, U.S.A.). 660 pp. Reviewer: M.A. Ford Foundry technology, by P.R. Beeley. Durban, Buterworth Scientific, 1982. R124 + GST. Reviewer: A.P. van Wyk Underground Transport Symposium. Johannesburg, The South African Institute of Mining and Metallurgy Special Publication SP 1. 300 pp. R65 (Non-Member), R55 (Member), + GST. Reviewer: C.L. Workman-navies A summary of the Project DevelopmentSymposium as presented by The Australasian Institute of Mining and Metalurgy. $A 25.00. Reviewer: D.J. van Niekerk Geology of uranium deposits. Proceedings of the CIM-SEG Uranium Symposium, September 1981, edited by T. I. I. Sibbald and W. Petruk. Quebec, The Canadian Institute of Mining and Metallurgy, Special Volume 32, 1985.268 pp. Canadian $40 members, $50 non-members (plus $3 for postage and packaging). Reviewer: M.S. Toros Crushing and grinding process handbook. Chichester (England), Wiley, 1986. £49. Reviewer: M.P. Hay O'okiep's 50th birthday The 0'okiep Copper Company Limited, situated at Nababeep s,ome 35 km from Springbok, recently celebrated its fiftieth anniversary.

Jan 1, 1987

By A. Rödfalk, P. Bloemer, J. P. Nilsson, N. Brogden

"Reliable and accurate metal transfer information during silicon tapping from an EAF is invaluable for decision-making and process optimization, while obtaining such information safely is a necessity.Elkem Thamshavn Norway, a producer of metallurgical-grade silicon, identified inherent safety problems with gauging fill levels in ladles using dip bars while molten metal was continuously pouring from a rotating EAF. Operator safety was a paramount concern, and an alternative automatic method of controlling the tapped fill level needed to be found.It was also considered that further benefits could be achieved such as monitoring the tapping flow from the EAF in order to identify any clogging, as well as the potential to use the live feed from such a system to assist decision-making regarding work around the taphole area.Agellis Group AB, Sweden, a company with over 30 years of experience in gauging molten metal levels in the metals industry, was able to design a solution for Elkem Thamshavn that would provide the required real-time process data while enhancing operator safety.This paper shows how the Agellis AB EMLI-L system was successfully installed at Elkem Thamshavn’s EAF continuous tapping area, how ladle fill levels were constantly monitored, and how full ladles were replaced by empty ones without the need for operators to be in the tapping area to take level readings. The results were used to compare the accuracy and reliability of Elkem Thamshavn’s current measuring methods with that of the EMLI-L system. The paper also covers how problems such as how to connect, run, and protect cables in and around the EAF tapping area, as well as connector and cabling survivability during the three day refractory pre-bake period, were solved. Finally, the paper discusses the potential production improvements, maintenance requirements, and data integration attainable through the installation of the system, as well as the major safety improvements that have been achieved."

Jan 1, 2014

By E. Arghavani, S. H. Amiri, S. Zare, F. Sepehri, M. Ramezanizadeh

Mineral processing plants include different stages like crushing, grinding, classification and concentration, all of which have partially affect the final product. To identify and solve the related problems of each stage, process audition should be carried out continuously to find the major solutions of improving product and decreasing the maintenance and operating costs. The Iranian Gohar-Zamin iron ore beneficiation plant consists of equipment such as gyratory and cone crushers, high pressure grinding rolls (HPGR), ball mill, dry and wet double-deck vibrating screens, hydrocyclones cluster, magnetic drum separators, thickener and horizontal vacuum belt filters. The defects of initial design as well as current non-standard operating conditions of equipment were monitored and detected and the opportunities for process optimisation were presented as follows: establishing the control loop of power draw for cone crushers, the modification of feeding chute in cone crushers to minimise the non-uniform wear of parts, removing segregation in the fresh feed bin and screen’s circulating load chute in order to provide the proper feed to HPGR, reducing wear rate on HPGR rolls surfaces, decreasing the amount of rejected materials in screen, equalising the solid content and particle size distribution (PSD) of feed in all magnetic drum separators and equalising the PSD of hydrocyclones overflow. This paper provides a guideline for the mineral processing industry to focus its efforts on process design to deliver the efficiency with minimum capital costs. Keywords: Process audition, gyratory crusher, cone crusher, HPGR, screening, hydrocyclones, magnetic drum separators

Jan 1, 2020

Solvent loading: It is agreed that it is advantageous, as far as reagent cost is concerned, to operate at maximum solvent loading. However, owing to the fact that no reliable automatic solvent flow controller is yet available, control tends to be erratic with the result that there is risk of losing uranium. As can be seen from Mr Tunley's plot, the graph representing total ammonia cost is fairly flat between loadings of 3.5 and 4.0 gpl, while the graph representing uranium loss in the raffinate is steep. It is, therefore, safer to operate slightly below optimum loading in the absence of absolute control. Should the purity of the final product gain importance, operation at optimum loading or even slightly above, may be advantageous. Solvent losses and clarification of pregnant solution: The cost of replacing solvent, as indicated by Mr Carman, represents a high percentage of the overall Purlex costs. It is, therefore, agreed that, amongst other factors, efficient clarification of the pregnant solution and mixer-settler design have an important bearing on the cost. However, as at Blyvooruitzicht, the Buffelsfontein plant can tolerate a suspended solids content of 50 ppm without serious deterioration in efficiency. An increase in the suspended solids content from 15 to 50 ppm normally accounts for an increase of approximately 1 ppm in amine loss. Clarification of acidic pregnant solutions is much more difficult than that of alkaline solutions. Sand clarifiers are being used at Buffelsfontein with moderate success. Clarified solutions containing less than 20 ppm of solids in suspension can be produced, depending on the quantity and type of flocculant used in the filtration process, the thickness and the grading analysis of the sand beds and the quality of supervision. An on-stream duty of approximately 0.15 gallon per sq ft of surface area is obtained. Hydraulic handling of clarifier sand, while cleaning, may effect the efficiency of a clarifier, as size segregation of sand particles may lead to inefficient "pockets" in a sand bed. Control of the solution level in the sand clarifier also affects the quality of the effluent. Exposure of the sand bed invariably causes a cloudy effluent. Recycling of the final and initial solution discharged before and after skimming the clarifier sand improves the clarification efficiency significantly. Post-precipitation of silica and possibly sulphate salts, after clarification, may give a false impression of inefficient clarification. This phenomenon is more pronounced when treating hot supersaturated solutions. Ageing and cooling of the solution before clarification assist in stabilising the solution and reduce precipitation after clarification. The maintenance cost of sand clarifiers at Buffelsfontein is in the order of 0.35 cent per metric ton of solution treated. A redundant ion-exchange column has been tested successfully, either as a primary or a secondary clarifier, depending on the quality of the filtrate treated. The conventional pebble and sand beds in the column have been retained. Operation was enhanced by the addition of a two-foot deep resin bed as a filtering medium. The suspended solids content was reduced to less than 5 ppm. Mixer-settlers: Mixer-settler design is a controversial subject but, in view of the high costs of solvent compared to relatively low pumping costs, it is believed that mixing and pumping functions should be separated. Separate facilities for pumping and mixing not only give greater operational flexibility but also permit eventual changes in the flow circuit as technology develops. Scrub technique: Unlike the pilot plant, where the crud was carried away in the aqueous phase, crud is carried over with the organic phase in the full-scale plant. This carry-over of crud into the strip bank aggravates crud formation in the first strip stage. This phenomenon may result from a slight difference in settler design and/or a variation in the relative phase depths in the two plants. Bypassing of the scrub aqueous solution from the fourth to the second stage was introduced in order to avoid dilution and partial neutralisation of the acid added to the third stage, as it is known that a low pH value enhances the transfer of iron into the aqueous phase. The low aqueous flowrate in the third scrubbing stage was overcome by introducing an aqueous phase recycle. Gleaning: Mr MacDonald's contribution on "gleaning" was most informative. This process for recovering solvent from raffinate seems to show at least as much promise as coalescers and other methods employed to date. Similar tests conducted at Buffelsfontein pilot plant gave 60 per cent amine recovery from raffinate containing 10 ppm amine. However, the circuit was not operated at equilibrium and recovery may be expected to drop as the amine concentration of the "Gleaner" circuit increases.

By J. F. Morrison, C. H. Wyndham, N. B. Strydom

INTRODUCTION The shovelling of rock in stopes is still a basic and important operation in many gold mines in the removal of gold-bearing rock from the stopes. There is, however, little factual knowledge of the factors which influence the the rates of energy expenditure and work output, and of the way in which variations in these factors, individually or in combination, affect the mechanical efficiency of the mine workers. What for example is the influence of different rates of shovelling, shovel loads and distances of throw? How does stope width and dip of the stope affect the mechanical efficiency of men shovelling rock? Recently a simple physiological test was introduced into the gold mining industry for classifying Bantu recruits into those capable of hard, moderate and light work. If this test is used to select only those Bantu mine workers who are capable of hard work for the task of shovelling rock in stopes then the rate of energy expenditure which could be expected from these men is 1.5 litres/min for the entire period of the shift. With an adequate knowledge of the influence of the various factors which affect the rate of energy expenditure of men shovelling rock in stopes it would be possible to set work standards for Bantu mine workers in stopes. This should be done in terms of the rate of shovelling, the shovel load and the distance of throw for any combination of width of stope, dip of stope, condition of foot wall and grade of rock in such a way that the resultant energy expenditure would be the 'optimum' that could be expected from the men but would be within their capacities for physical work of an endurance nature (that is, 1. 5 litres/min from the 'average' Bantu mine worker). Work standards could thereby be determined for the different stopes of a mine on a sound and systematic basis. In order to supply the information required a study was carried out by the Human Sciences Laboratory in which the work output and energy expenditures (in terms of oxygen consumption in litres/min) were measured on six highly trained Bantu mine workers under the following conditions: (a) rates of shovelling of 3, 4, 5, 6, and 10 shovels per minute. (b) loads of from 9 to 18 lb on the shovel. (c) distances of throw from 8 to 20 ft. (d) stope width of 28 in., 42 in. and 72 in. (e) dip of stopes of 0°, 15° and 30°. (f) rough and smooth footwalls and various grades of rock size. This paper gives the main results of practical importance of this study. Method The experiments were designed and conducted in conjunction with the Work Study Department of one certain underground conditions such as variable stope widths, stope angle, etc., were made available in a mine Surface Training School and suitable subjects were selected from the large number of labourers being put through the training school. Subjects Bantu recruits who had returned to the mine for a new contract and who had previous underground experience on shovelling were considered to be suitable as subjects for the experiments. The particulars of the subjects are given in Table I. TABLE I PHYSICAL CHARACTERISTICS OF SUBJECTS Weight Height Surface area Max O2 capacity Subject (Kg) (cm) (sq meters) (Litre/minute) A 71.5 167.3 1.80 3.5 B 61.5 162.3 1.65 2.8 C 63.0 164.1 1.69 2.4 D 66.5 167.4 1.75 2.8 E 70.2 164.6 1.77 3.0 F 77.8 173.1 1.92 3.8 Training The method of shovelling, accepted by the Work Study Department, was demonstrated to the subjects who then practised the movements with empty shovels, under the supervision of an instructor. After the technique was mastered, the men started shovelling rock and were trained for at least four hours per day to work at the higher shovelling rates. Training was continued for three weeks to enable the subjects to achieve a reasonable degree of physical training and conditioning. Shovelling method In both the kneeling and standing positions the subjects faced the pile of rock, grasped the shovel in the accepted manner and pushed the blade of the shovel into the base of the pile of rock, sliding the blade between the rock and the concrete floor. In the standing position (72 in. wide stope) the back leg assisted in the movement by pushing the knee against the back of the hand holding the shovel handle. In the kneeling position the elbow was tucked into the side of the body so that the muscles of

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

By N. V. Moraka

Mining companies are required by law to improve representation of women on their boards. However, progress in this regard has been slow. Boards of directors play an important role in formulating corporate strategy, risk assessment, and effective governance for sustained financial performance. Although some women have successfully maintained board seats, others have been unable to do so. It is difficult to ascertain whether women are being appointed as tokens to satisfy social pressures, as little is known about the experiences of women board members in mining, which may inform or refute tokenism. In-depth interviews were conducted with 20 women and 16 men across six listed mining companies. Thematic data analysis revealed evidence of tokenism where recruitment to mining boards is compliance-based and is informally driven by influential directors. Adverse boardroom experiences that further confirmed tokenism were reported by women, such as disregarding their contributions, condescending behaviour, and limited influence in decision-making, while other women sought to validate their competence and oppose social exclusion. This study recommends that a strong Board Chair and nominations committee is critical to ensure sustainable recruitment of competent and suitably qualified women; and further foster a culture of inclusivity and valuing gender-diverse boards.

Dec 13, 2023

By R. M. Mashishi, T. Malehase, O. J. Okonkwo

The concentrations of selected trace elements (As, Cd, Hg, and Pb in run-of-mine (ROM) coal, discard, and coal product were investigated to assess the efficiency of beneficiation in reducing trace element concentrations and ascertain any implications regarding environmental compliance to regulatory frameworks. Samples were collected from a colliery in Mpumalanga Province twice a month for a period of 24 months. The samples were ashed to approximately 0.21 mm, then digested in a mixture of 70% HNO3 and 40% HF and analysed using inductively coupled plasma-mass spectrometry (ICP-MS). Except for Pb, the mean concentration of all elements decreased from the ROM stage to the coal product stage. The order in which trace elements occurred from the highest to lowest throughout the production chain was Pb>As>Hg>Cd. With the exception of Cd, the mean trace element concentrations in the discard were above the total concentration threshold (TCT) set for landfill disposal. The As, Hg, and Cd concentrations in the product were well below the thresholds for all land uses. However, Pb concentrations in the product coal were above legal limits, which is of concern with regard to environmental compliance and the performance and marketability of the product.

Dec 13, 2023

By S. Swanepoel, A. V. Cherkaev, Q. G. Reynolds, M. Erwee

Ferrochrome (FeCr) is a vital ingredient in stainless steel production and is commonly produced by smelting chromite ores in submerged arc furnaces. Silicon (Si) is a componrnt of the FeCr alloy from the smelting process. Being both a contaminant and an indicator of the state of the process, its content needs to be kept within a narrow range. The complex chemistry of the smelting process and interactions between various factors make Si prediction by fundamental models infeasible. A data-driven approach offers an alternative by formulating the model based on historical data. This paper presents a systematic development of a data-driven model for predicting Si content. The model includes dimensionality reduction, regularized linear regression, and a boosting method to reduce the variability of the linear model residuals. It shows a good performance on testing data (R2 = 0.63). The most significant predictors, as determined by linear model analysis and permutation testing, are previous Si content, carbon and titanium in the alloy, calcium oxide in the slag, resistance between electrodes, and electrode slips. Further analysis using thermodynamic data and models, links these predictors to electrode control and slag chemistry. This analysis lays the foundation for implementing Si content control on a ferrochrome smelter.

Mar 14, 2024

By J-N. Oyourou, R. McCrindle, C. J. S. Fourie

"Many mines in South Africa were inappropriately closed and left unattended during the last century. These old mines are potential sources of environmental pollution and may pose a health risk to local populations, since the surrounds contain elevated levels of toxic elements. Soil from the old Edendale lead mine property in Mamelodi Extension 11, east of Pretoria, which was suspected to be contaminated with lead, was analysed. The mine, which primarily extracted galena, was decommissioned in 1938. During this study, the old mine property and surrounds were screened for zinc and lead using a field-portable X-ray fluorescence (pXRF) spectrometer. The metal concentrations, which ranged from 18 to 7 300 mg/kg for zinc and from 50 to 21 000 mg/kg, for lead, were plotted together with the GPS coordinates to produce a concentration distribution map for lead and zinc. This map revealed three anomalies of unacceptably high concentrations, possibly corresponding to areas where ore had been piled or dumped to waste from the old mine. Thirty-six of the soil samples that were analysed by pXRF on site were selected and analysed in the laboratory using inductively coupled plasmaoptical emission spectrometry (ICP-OES) for verification purposes. The zinc and lead concentrations obtained from the two analytical methods were compared using linear regression analysis. Excellent correlation was obtained between the results from the two methods (r2 = 0.99 for zinc and r2 = 0.95 for lead). IntroductionEarly economic development in South Africa was based mainly on mining. However, these activities left a legacy of approximately 6 000 improperly closed mines scattered throughout the country (SAI, 2009; van Schie, 2012). Due to their proximity to settlements, these abandoned mines may pose a potential health risk to humans and an environmental hazard. Mining activities generate large amounts of waste, mostly in the form of overburden and process tailings, which often contain high concentrations of toxic elements. Bioavailable toxic elements can contaminate crops growing in the polluted area (Kala, 2010; Marwa, Meharg, and Rice, 2012) or eventually migrate and detrimentally affect the groundwater (Rösner and van Schalkwyk, 2000). Moreover, sulfides accumulated in mine waste generate acid minewater (Rösner and van Schalkwyk 2000). Unfortunately, owners of mines, closed before the promulgation of the Minerals Act more than twenty years ago (Act 50 of 1991), avoided the compulsory rehabilitation of the environment enforced by this legislation. Toxic elements, such as lead, which were confined within ores, may become exposed through mining and are therefore more easily mobilized within the environment. Elements essential to human and plant metabolism, such as zinc, when exposed by mining activities, may become hazardous due to elevated concentrations (Aslibekan and Moles, 2003; Wuana and Okiemen, 2011). Humans exposed to potentially toxic metals may experience harmful effects as discussed elsewhere (Nriagu and Pacynar, 1988; Wayne and Ming-Ho, 2005)."

Jan 1, 2019

"Chairman: Mr. K. F. LaneRapporteur: Mr C. T. ShawPapers:Design of crushing plant flow sheets by simulation by T. GurunThe impact of transportation networks upon the potential supply of base and precious metals from Sonora, Mexico by P. de V. Harris and D. E. EurestyProfitability sensitivity analysis of a mining venture by C. A. Beasley and E. P. PfleiderTechnological innovation and its potential effect on the opening of new gold mines in South Africa by N. C. JoughinMr Turgay Gurun, in presenting his paper, indicated that this simulator was no purely theoretical exercise, but that the model had been used in the design of crushing plants of capacities ranging from 3 000 tons per day to 66 000 tons per day, and that recently the design of a plant of capacity of 99 000 tons per day had been studied.The crushing plant simulator was an independent portion of a much more comprehensive simulator for the design of a. complete recovery plant. It would be possible to use each section of this simulator on its own, and simulators would be designed to cover flotation concentrates, cash flow analyses of the entire project, and so on.Each simulator would be backed by a comprehensive data bank. For example, the crushing plant simulator was backed by such a data bank which included the performance and cost data from five manufacturers for an average of 30 items of process and materials handling equipment each. This meant that data preparation involved generally less work than would be required for a manual calculation. On average, data preparation for one run took 30 minutes and three minutes of computer time on an IBM 360/40 completed the run. The model could be valuable as a design tool in that it allowed the designers an opportunity to make a thorough examination of many alternative designs. It was also of value to plant operators as it could be used to predict the consequences of operating decisions.This paper generated much interest and there were numerous questions and contributions, so many, in fact, that the discussion had to be cut short.It was pointed out by Mr K. F. Lane that crushing plants represented a very large capital investment. A plant designed for 40 000 tons per day at 98 per cent efficiency might well in practice be run at 50 000 tons per day at, say, 83 per cent efficiency. He asked how, therefore, their design could be investigated without building economic criteria into the model? The author conceded that this was a tender point. He would have liked to have given facilities for more variability of the metallurgical information. He pointed out, however, that while there was no overdesign for conservatism built into his system, some overdesign was inevitable as the performance characteristics given by the manufacturers were generally conservative. Also, in his system, if lower recovery was allowed for, the system would nut through more tonnage."

Jan 1, 2014

By B. Orgilbayar, B. Unursaikhan, S. Sukhbat, Ts. Zagarzusem, D. Baasanjav, L. Jargalsaikhan, E. Otgonjargal, N. Sugir-Erdene, Ts. Soyolmaa

This study has investigated the efficacy of the gravity beneficiation method based on gravitation and centrifugal forces for manganese ore. Powdered samples of manganese ores from the Unagad deposit in Mongolia were analysed for their element and mineralogical composition using ICP-MS and X-ray powder diffraction (XRD). The analysis presented the mineralogical compositions of the ores as hydro goethite, manganese minerals and magnetite, gangue minerals as quartz, albite, orthoclase and microcline of manganese ore. Manganese minerals are white in colour and have micro-veinlet, fine grained-aggregates associated with gangue minerals. The most important manganese minerals are hausmannite, pyrolusite, rhodochrosite, and manganosite. The composite of feed containing 17.31 % Mn and 36.3 % SiO2 was processed in a shaking table. In the experiment, a concentrate assaying 41.37% Mn was obtained from this composite with 65% recovery. In another experiment, f80=0.074 mm particle size ore was used in the MGS concentration test. A concentrate containing 38.34 % Mn with 75.2% recovery was produced in this experiment. The results showed that it is possible to obtain concentrate through gravity processing of manganese ore, which is an economically beneficial process for producing a product of a standard requirement. Keywords: Manganese ore, gravity separator, centrifuge, shaking table 1. Introduction

Jan 1, 2020

By P. Muthaphuli

Kumba Iron Ore?s Zandrivierspoort (ZRP) magnetite-haematite project aims to mine and beneficiate a magnetite resource with low contaminant levels to produce from 1 Mt/a to 2.5 Mt/a product, which will be either a concentrate, micro-pellets for direct reduction, or blast furnace pellets. Anglo American Technical Solutions Research conducted a number of piloting campaigns to validate the process design flow sheet, demonstrate process performance, and to generate data for use as a design basis. Secondary to this, the pilot plant was to produce approximately 7 t of magnetite-haematite concentrate with low enough SiO2 to be used as feedstock for pelletizing studies. The pilot plant achieved 34.2% mass yield, at 69.0% Fe, 2.2% SiO2, from an IsaMill grind of 80% -45 µm. This product quality will compare favourably to other leading direct reduction (DR) pelletizing concentrates. However, two-stage comminution to 80% -75 µm and beneficiation of ZRP ore will produce a blast furnace (BF) quality pelletizing concentrate, indicative quality being 67.6% Fe and 4% SiO2, at higher mass yields. An economic evaluation between producing a DR and a BF pelletizing concentrate will have to be conducted prior to finalizing the concentrate production flow sheet..

Jan 1, 2014

By A. Dabbagh

The aim of this research was to investigate the effect of coke particle size on the thermal profile of the charge bed in the sintering process of iron ore. Six different ranges of coke particle size that could be used in practice in the sintering line of Esfahan Steel Company (ESCO) were used while parameters such as ratios and particle sizes of other ingredients, ignition temperature, and suction power were kept constant. Thermal profiles were obtained by measuring the temperature changes at three points in the sintering bed. The influence of coke particle size on rate of temperature rise, maximum temperature of the sintering bed, and the flame front velocity of the sintering bed was determined by analysing the thermal profiles. Moreover, the cold strengths of the sinters were measured using the Tumbler method. The results indicated that the coke particle size has a significant impact on the thermal properties of the sintering bed. Based on the results, a coke particle size between 0.212 mm and 3.350 mm was determined as the optimal range for the specific conditions in the sintering line of ESCO. Keywords iron ore sintering, coke particle size, thermal profile, flame front velocity, Tumbler index.

Dec 1, 2013

By P. J. van Staden, T. W. Walker

The Minfurn is a novel carbon-regeneration furnace developed at Mintek. It combines the advantages of direct resistive heating in a vertical-tube furnace with those of continuous operation, in a furnace whose capital, operating, and maintenance costs compare favourably with those of conventional rotary kilns. After successful tests under experimental conditions on carbons containing different contaminants, a 3 kg/h unit was installed on the carbon-in-pulp (CIP) plant at the Klipwal Gold Mine near Piet Retief, where it has been operating at, on average, 123 per cent of its design capacity. Since the installation of the Minfurn, monthly average losses of dissolved gold of less than 0,02 p.p.m. have been maintained for several successive months for the first time since January 1989. It is also possible that the monthly average residue values have been reduced. Further improvements to the carbon circuit are possible, and the possibility of making further savings by a reduction in the carbon-throughput rate still needs to be investigated. The mathematical modeling of the furnace has progressed to the stage where the future scale-up and design of the Minfurn can be carried out by simulation of the performance of different designs, and choosing the design that yields the desired performance.

Jan 1, 1993

By C. C. Johnson

In the fourteen years that Rössing Uranium Limited has been in production, the metallurgical operations and controls on the leaching plant have evolved through four basic stages. Initially, the emphasis was placed on the achievement of consistent plant operation by overcoming severe startup difficulties. The second stage involved the attainment of the design operating targets, and also the commissioning of the ferric-leaching reactors in order to achieve a ferric ion concentration of more than 3,0 g/l. Improvements in control then became the priority, with the emphasis on consistently achieving the target concentrations of ferric ions, total iron, and terminal acidity. The latest phase has concentrated on the optimization of costs by means of adjustments to the historically established operating parameters in order to achieve large savings on consumables while maintaining the leaching efficiencies. Apart from the obvious incentive of reducing costs in an inflationary economy and a depressed uranium market, impetus for this work was given by a change in the type of ore from the open pit, which has the effect of reducing the extraction efficiency while increasing the consumption of consumable materials. These problems and their solutions are discussed in detail, and the importance to cost-effective optimization of an accurate, up-to-date cost-reporting structure is stressed.

Jan 1, 1990

By M. U. Ozbay, D. R. Lougher

An in-situ experimental programme was carried out to improve the understanding of the rockmass and pillar behaviour in moderately deep hard-rock mines. The experiments were carried out at Impala Platinum mines and consisted of precise levelling measurements in the footwall of the reef, stress measurements in pillars, convergence measurements in the stope, and petroscope observations in pillars. The results were analyzed using a computer program in an attempt to quantify the characteristic behaviour of the rockmass as well as the pillars. The measured off-reef displacement data were found to co11fonn to the trends obtained from elastic modelling and the correlation could be improved by modelling the small pillars with reduced modulus to simulate yielding' of the pillars. The stress strain curve obtained from analyzing the in situ results, showed that a 6x 3 xl m pillar yields without significant load shedding at peak stress levels of approximately 208 MPa. The closure measurements confirmed that the mechanism of yielding is mainly that of pillars punching into the foundations. Slight to moderate sidewall fracturing and slabbing might be contributing to yielding, but to a much lesser degree than the former mechanism, as the petroscope observation revealed the existence of an intact region beyond 0,6m from the pillar sides.

Jan 1, 1995